Search Documents

By C. Poon

For slope stability, knowledge of major and minor discontinuity sets that form the rock mass fabric is paramount for pit slope designs. Due to the increased awareness of health and safety in mining projects, efforts have been made to limit structural mapping in order to minimize the risk to personnel associated with approaching potentially unstable areas. Recognizing the importance of such safety precautions, Golder Associates Ltd. is applying a combination of techniques including 3D photogrammetry, conventional mapping and drilling with core orientation to enhance structural data collection. Photogrammetry uses digital photographs to produce a virtual model of a rock mass surface. The application of these techniques will be exemplified through an expansion design of an existing open pit. A comparison of stereonets obtained using these techniques showed some agreements, but also highlighted limitations of each method. The application of photogrammetry was found to be very useful in complementing the other existing techniques.

May 1, 2009

By H. S. Price, J. C. Cavendish, R. S. Varga

This paper presents a new technique for solving some of the partial differential equations that are commonly used in simulating reservoir performance. The results of applying this technique to a simple problem show that one obtains accurate pressure values near wells, as well as accurate pressure pdients, which can be explicitly calculated. The method is completely rigorous in that convergence of the discrete numerical solution to the continuous solution for both pressure and pressure gradient is established. High-order, piecewise-polynomial approximations are used near the wells where pressure gradients are steep, while low-order, piecewise-polynomial approximations are used elsewhere to reduce greatly the calculation time. This combination is shown to give a uniformly good approximation to the solution. These approximations, obtained by using a Galerkin process with suitable Hermite subspaces, are shown to be theoretically and numerically superior to the usual approximations obtained from standard finite-difference techniques. Not only are much greater accuracies obtained, but computer times are also greatly reduced. The application of this technique to multiphase flow problems (e.g., single well coning problems) would have considerable practical interest, but such extensions of this technique with full mathematical rigor have not been made as yet. However, the numerical methods presented here are general, and in principle extend to multidimensional, multiphase flow. Moreover, the preliminary results given in this paper are sufficiently encouraging that we feel the effort in attempting these extensions is justified. INTRODUCTION The problem of obtaining accurate pressure distributions and pressure gradients around wells is of considerable importance in the numerical simulation of reservoir performance. The most common approach to solving this problem is to use finite difference techniques (see McCarty and Barfield9 or Peaceman and Rachfordl0). This approach, however, has many disadvantages, the major one being that many grid points are generally necessary for accurately describing the pressure distribution and the pressure gradient around wells. This need for a fine grid results in large computer times and often in prohibitively high costs. Besides investigating the method of finite differences, some authors, such as Welge and weber17 and Roper, Merchant and Duvall,13 have considered a combination of analytical and numerical techniques with some success. These approaches, however, are all nonrigorous and quite often cannot even be applied. In this paper, we present a numerical formulation of high-order accuracy, based on the Galerkin method, for solving this problem. We treat here only the partial differential equation that describes steady-state, single-phase flow. However, the methods presented are general and in principle extend to multidimensional, multiphase flow. Specifically we treat special cases of the problem in two dimensions described by: where G is a rectangle (with sides parallel to the coordinate axis) with boundary ?G, ?/?n denotes the outward normal, and y and B are non-negative constants such that y + B > 0.

Jan 1, 1970

By H. A. Wilhelm, P. Chiotti, G. A. Tracy

A summary of analytical, X-ray, thermal, and metallographic data obtained in the study of the Mg-U system is presented. No intermetallic compounds are formed by these two elements, and their mutual solubility is limited at temperatures up to 1255°C. The compositions of the liquids which coexist at 1135°C under a pressure of 3 atm are 0.14*0.05 wt pet U in magnesium, and 0.004 wt pet Mg in uranium. The solubility of uranium in magnesium decreases to 0.0510.03 wt pet at 675OC, and to about 0.0005 wt pet at 650°C. Due to the reactivity of both uranium and magnesium toward crucible materials, the choice of a suitable crucible presented a problem. Crucibles made from high purity magnesia to which 10 wt pet MgF2 was added to reduce porosity proved to be satisfactory. Some observations made with the use of other crucibles are given. THIS investigation was made to establish the phase diagram for the Mg-U system. Ahmann,' formerly of the Ames Laboratory, did some work on the system. He used several methods in an attempt to prepare Mg-U alloys. One of the methods involved the reduction of UF, with a large excess of magnesium. In these experiments, the magnesium wet the surface of the uranium, but there was no evidence for compound formation. The maximum solubility of magnesium in uranium was indicated to be 0.01 wt pet. In another set of experiments, uranium chips as well as uranium powder were heated in contact with molten magnesium in a graphite crucible for periods of time up to 48 hr. A reaction layer was found at the Mg-U interface in several instances. X-ray analysis of the layer material showed the presence of UC and some additional unidentified lines which were interpreted as indicating the possibility of an intermetallic compound of uranium and magnesium. These studies indicated the maximum content of magnesium in uranium to be 0.043 wt pet. One sample of magnesium which had been heated at 1025°C in contact with excess uranium was found by chemical analysis to contain 0.275 wt pet U. Rules, based on empirical or semi theoretical considerations, which attempt to predict the alloying behavior of metals have been presented in the literature. Although these rules are not infallible, they nevertheless serve as useful guides. Using them, several generalizations can be made concerning the Mg-U system. According to Hume-Rothery's' atomic

Jan 1, 1957

By J. H. Fletcher

AIR has been cooled, heated, washed; humidified and dehumidified for many purposes and in many industries. At a number of metal mines air is conditioned to reduce the high humidity and unbearable heat found in deep workings, and at some mines air is washed to allay siliceous dust. Steam is introduced into the intake air at many coal mines, particularly in winter, for the purpose of keeping loose coal dust so moistened that the hazard of an explosion is lessened. This paper will describe a further successful application of air conditioning in a coal mine, where, for over three years, all intake air has been cooled to a constant temperature for the sole purpose of preventing roof falls.

Jan 1, 1931

By Richard J. Mainiero, Marcia L. Harris, James H. Rowland

In the past several years, there have been a number of blasting-related carbon monoxide migration incidents. In each case, there have been some common factors that appear to be related to carbon monoxide migration. Geology, heavy confinement of the blast, close proximity to the affected structure, and open pathways into the affected structure are just a few. Prince William County, VA is an area undergoing a boom in suburban development. In the year 2001, more than 4,050 new homes were constructed within the county.1 In the new housing development located in Bristow,VA, trench blasting was utilized to excavate proposed sewage and utility lines. On November 8, 2002, a trench blast was conducted for the installation of utility lines. Later that evening a carbon monoxide detector alarmed in a nearby house. The gas company and fire department sampled for carbon monoxide and measured 100 ppm and more than 200 ppm on the first floor and in the basement respectively. Subsequent efforts to prevent migration of CO into the nearby homes met with mixed results. The only reliable technique for protecting neighbors from CO appears to be the placement of CO monitors in the homes. The events are presented and discussed.

By K. A. Johnson

Marshall and Bird have published the results of a cooperative investigation by the Bureau of Mines in which they developed a procedure for measuring the agglutinating value of coal.4 As stated in their paper, the procedure outlined was suggested by the early worn of Richters5 and Campredon,6 whose procedures were hurriedly modified to meet the need of an investigation then in progress. Since the publicatien of that paper, further work has been done in an attempt to show how the variables involved affect the concordance of the results, in order that such results may be obtained in different laboratories. Briefly, Marshall and Bird's method for determining the agglutinating value of coal consists in carbonizing an intimate mixture of 10 parts by weight of sand and 1 part by weight of coal in a porcelain crucible at a uniform temperature of 950° C. in a, vertical, cylindrical, electrically-heated furnace. After carbonization, the resultant buttons are crushed in a testing machine and the breaking strengths recorded in grams. The agglutinating value reported is the average breaking strength of 10 buttons. The coal for the test is prepared by crushing to pass a 100-mesh screen. The sand used as a diluent is sized between 40 and 50 mesh sieves with openings of 0.381 icon and 0.279 millimeters, respectively.

Jan 1, 1930

By A. Wahab Khair, Nagendra P. Reddy

"This paper presents an analysis of preliminary tests on the effect of in-situ and operating parameters on fragmentation of coal using a specially designed unique automated rotary coal cutting simulator (ARCCS). In these tests coal blocks with an approximate dimension of 18 in. x 15 in. x 6 in. (45.7 cm x 38.l cm x 15.2 cm) were first. subjected to confining pressures, equivalent to in-situ conditions. Such. blocks were then cut by the cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted by using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using an optical microscope with a camera attached to it. Furthermore, the coal fragments were collected in bags using a vacuum cleaner. These fragments were then sieved for size distribution analysis. The results of the preliminary tests indicated that underground coal cutting can be simulated in the laboratory and the effects of the important parameters, i.e. operating and in-situ parameters, can be studied successfully. INTRODUCTIONThe continuous-mining machines which were introduced in the 1950's now account for more than half the production of coal from underground mines. Unfortunately, these continuous miners, which were designed for increased productivity, have also increased the concentration of respirable dust in mines. As a result, the Federal Coal Mine Health and Safety Act of 1969 was enacted to enforce on the coal operators that the airborne respirable dust not exceed 2 mg/m3, and was intended to reduce the incidence of coal workers pneumoconiosis. This plus the other aspects of the legislation and the subsequent monitoring and enforcement by MSHA made it very imperative that the coal operators provide a relatively healthier and safer working environment for the coal miners. Since 1970, the Federal government has paid over 11.7 billion dollars to more than 470,000 miners with coal workers pneumoconiosis and their survivors (1). These regulations, coupled with the assessment of the continuing burden on miners, the mining industry and taxpayers appear to have provided an impetus for the mining .community towards comprehending the different parameters that influence dust generation and entrainment."

Jun 1, 1988

By L. G. Marsh

The manufacture of lubricating oils from wax-bearing crude petroleums involves the removal and recovery of the paraffin wax contained in the lubricating distillates. During this process several intermediate products are formed, among them the mixture of waxes and oils known to the refiners as "foots oil." Because of its complex character, foots oil is little understood, and therefore methods of handling it in refineries are often inefficient. The Bureau of Mines is studying the manufacture of lubricating oils, and during the work has investigated the redistillation of foots oil. This report gives in brief the results of the investigation, and recommendations based upon it.

Jan 1, 1926

By C. H. Elder

A 5-hole pattern was drilled from the surface at a site near Oak Grove, Jefferson County, Ala., to degasify the gassy Mary Lee coal bed in advance of mining. Gas and water production was monitored for 1 year, 4 months to allow gas flow to stabilize fully. A thickened water stimulation treatment was designed and applied in one hole of the pattern to evaluate this degasification technique for the Mary Lee coalbed. A gas production rate of 70,000 fts/day after stimulation treatment indicates that the use of vertical boreholes coupled with hydraulic fracturing in advance of mining the Mary Lee coalbed would provide for more rapid degasification and could provide a possible source of natural gas.

Jan 1, 1974

By H. Conrad, K. Janowski, E. Stofel

In a previous paper,1 the occurrence of (0001) and (0111) twins was reported for compression tests of 60-deg-oriented sapphire rods in the temperature range from 1100° to 1300° C. Subsequent to this initial work, additional tests have been conducted, and twinning has been found to occur at temperatures as high as 1500° C. Also, the temperature and strain-rate conditions for the two types of twins and for slip have been established in more detail. The present note covers this more recent work. The compression-test data are summarized in Table I. The techniques for identifying the twins are optical examination up to X1000 and X-ray analysis.' It is evident that (0711) twins are pre-

Jan 1, 1965

By Donald E. Crowell

Due to falling metal prices and depletion of ore reserves, lead- zinc mining in the Leadville, Colo., area gradually came to a halt in the 1950's. Exploration work continued, however, and by 1969 sufficient ore had been blocked out to warrant sinking a shaft and erecting a new concentrator to treat 700 tpd. The new shaft and concentrator were to be located in Iowa Gulch several miles east of Leadville at an elevation of 11,100 ft. The Leadville project is a joint venture between Newmont Mining Co. and Asarco, with Asarco being the operator. Design work began in the fall of 1969. Engineering was done by Torkelson Engineering Co. of Salt Lake City in conjunction with the central engineering department of Asarco. The plant was constructed by Stearns-Roger Corp. Construction began in the spring of 1970 and the plant went onstream in April 1971.

Jan 11, 1972

By M. S. Klima, P. T. Luckie

An evaluation of the operating performance of a recently designed pneumatic centrifugal classifier is presented. This classifier has been modified from a separate air and feed input design to an entrained solids in air feed input. The evaluation first required determining the size distributions for the three streams (feed, fine, and coarse). Using size distribution data and mass flow rates, a size selectivity curve was calculated for each operating condition tested. This curve, in turn, was characterized by appropriate selectivity parameters (i.e., the equiprobable or cut size, the sharpness index, and the apparent bypass values). The variation of these parameters with classifier operating conditions was examined. From these evaluations, the "best" operating conditions for the classifier were then determined.

Jan 1, 1985

By W. L. Fink, R. S. Archer

This paper describes results obtained on aluminum-beryllium alloys and aluminum-beryllium-copper alloys in the preparation of which aluminum of 99.95 per cent. purity was used. The constitution and structure of the high purity binary alloys are given. The aluminum-beryllium eutectic occurs at 0.87 per cent. beryllium and 645° C. The solid solubility of beryllium in aluminum at 631° C. is 0.05 per cent, beryllium, and at room temperature is less than 0.013 per cent. beryllium. The densities of the alloys are substantially the same as the values calculated on the assumption that the densities of the elements are not changed by alloying. All of the alloys age-harden at room temperature after a solution heat treatment, and the chill cast aluminum-beryllium-copper alloys age-harden at room temperature without a prior solution heat treatment. Hardness and tensile properties are given. Salt spray corrosion tests on sheet specimens are described. It is shown that beryllium docs not lower the corrosion resistance of aluminum to salt spray provided the alloy has received a solution heat treatment. Commercial Possibilities of Beryllium Alloys Beryllium has certain properties such as low density, high hardness, good corrosion resistance, low thermal expansion and fairly good electrical conductivity, which would indicate that it is worthy of consideration as an ingredient of light alloys. It was not until recently, however, that beryllium could be produced with sufficient ease to encourage research along this line. The production of beryllium by electrolysis from a fluoride bath has now developed to the stage where it could be used commercially if there were sufficient demand for the element. Claims made in certain newspapers and technical articles in regard to thc strength and corrosion resistance of thc aluminum-beryllium alloys are not justified by experimental results. Moreover, beryllium is an expensive metal ($200 a pound at the time this work was done) and, on account of the nature of its ore and the consequent difficulty of its extraction, it will in all probability continue to be a relatively expensive metal, although the cost would undoubtedly be a great deal less than $200 a

By Bingwen Z, Fengyi K

The hydraulic-stowing mining method is most effective for mining thick coal seams. It is superior to the sliced cover- caving and artificial mining method and the fully mechanized sublevel-caving mining method for the following reasons - a much higher recovery rate is achieved, there is much less surface subsidence and roof pressure, there is no hidden danger of gob fire, and much less methane emission and coal dust problems, etc.. However, its superiority is overshadowed by its backward stowing technique which makes mechanisation of mining and stowing difficult, causes bleed water interference to production and to the environment and is uneconomic because of the high cost of stowing material. These disadvantages limited its application to coal seams that are difficult and not suitable to be mined by other mining methods. The remedy is in reforming it thoroughly to permit mining of otherwise unminable seams and this paper presents the reformation.

Jan 1, 1992

By M. R. Geer, H. F. Yancey

WITH the exception of pneumatic processes and ii few special beneficiation methods of comparatively limited application, all mechanical coal-cleaning and mineral- dressing processes involve the admixture of solid particles with a liquid, generally water. Upon completion of the beneficiation process the solids must be reclaimed from the water. With coarse particles separation of solids from water is accomplished readily by the simple expedient of screening, but recovery of fine solids presents a much more difficult problem. Thickening and dewatering are practiced so generally, both within the mineral industry and else- where, that they have been the subject of study through the years and a number of processes for making the solid-liquid separation have been developed. Dorr-type thickeners have been standard equipment for many years, and more recently driers employing centrifugal force have gained in popularity. 1 A cyclone device employed to thicken the loess suspension is a novel feature of the loess heavy-medium coal-cleaning process developed by the Netherlands State Mines in the thirties. The cyclone thickener was first mentioned by Driessen2 in 1939 in a paper describing the loess process and has been the subject of two more recent reports by the same author.3 The cyclone does not differ greatly from cyclone dust collectors used in this country for years, except that it is operated wet rather than dry. Advantages of the cyclone over other thickening devices are its simplicity of construction, high capacity, and the fact that, having no moving parts, it is simple and inexpensive to operate. The Bureau of Mines became interested in the cyclone after one of the present authors observed it in operation in the Netherlands in 1945. The first experimental work with the cyclone conducted by the Bureau of Mines was an investigation of the unit functioning as a heavy-medium cleaner for fine coal-a use for the cyclone that was conceived long after it had been perfected as a thickener. The results of this investigation were published last year.4 The present investigation deals exclusively with operation of the cyclone as a thickener. OBJECT AND SCOPE OF INVESTIGATION Although the cyclone thickener has been dealt with in three reports by Driessen, its use as a thickener was not the principal subject of any of these reports and therefore neither the cyclone itself nor its operation was described completely. The design of the cyclone was described only in a very general way, only limited operating results were given, and virtually nothing was disclosed about the influence of the various possible operating variables. Moreover, the Netherlanders apparently had employed the cyclone exclusively for thickening loess and had not employed it on coal slurries. One English colliery has used a cyclone to thicken coal slurry,5 and as it appeared that

Jan 1, 1948

By M. A. Elliott, F. W. Brown

"INTRODUCTION During the recent war the Bureau of Mines, at the request of one of the armed services, investigated the hazards that night be encountered 5n handling perchloric acid, particularly if spilled on certain materials. The hazardous nature of perchloric acid when mixed with reducing agents had been known qualitatively, but it was desired to obtain quantitative data on the explosion hazards of such materials. Accordingly, tests were made to determine the sensitivity of mixtures of perchloric acid and oxidizable materials to initiation by heat, impact, sparks, flame, and explosive impulses. This report summarizes the results of those tests.PROPERTIES OF PERCELORIC ACIDAnhydrous perchloric acid is a colorless,hygroscopic, volatile, mobile liquid that fumes in the air. The anhydrous acid is unstable at ordinary temperatures, and therefore the commercial acid is a water solution containing either 60 percent or 70 percent by weight of the anhydrous acid. The commercial acid is widely used in chemical analysis, frequently to oxidize organic material. If proper precautions are not observed, such an oxidixation may become exceedingly rapid and result in an explosion. Several such explosions involving the acid are mentioned in the literature. 4, 5, 6/"

Jan 1, 1948

By F. Estrada

El presente estudio revela la geología del yacimiento diseminado de cu-mo de almacén de Ica. Este depósito porfirítico, inicialmente estuvo compuesto de microgranito y pórfido cuarcífero, los cuales son relacionados con los procesos de alteración y mineralización del depósito. Posteriormente, estos eventos intrusivos de postmineralización están representados por un enjambre do diques de composición decítiica, pórfido diorítico cuarcífero y andésitico. Asimismo se describe el proceso de mineralización y la distribución de este mineral, la alteración hidrotermal y el zoneamiento de la mineralización-alteración.

Nov 20, 1972

By L. A. Wright, H. L. McKinley

PINE Creek mine of Union Carbide Nuclear Co. is some 23 miles northwest of Bishop, Calif., in the Sierra Nevada Mts. Office and mill are 7800 ft above sea level, the 1500 level portal is at 9300 ft, the A level portal at 10,800 ft, and the 3050 portal at 11,500 ft. Original claims were located in 1916, and the mine worked intermittently until 1936, when it was purchased by Union Carbide Corp. Since then the property has been operated continuously, except for two brief periods when operations were suspended because of manpower shortages. Mine production through 1956 amounted to 2,792,425 dry tons of ore.

Jan 10, 1957

By J. O. Marsden

The Candelaria copper-gold mine is located approximately 25 km south and east of Copiapo in Region III, Chile. The original concentrator was designed to treat 28,000 t/d (30,800 stpd) of chalcopyrite-bearing ore through a circuit consisting of a single 11.0 m (36 ft) diameter SAG mill, two ball mills, conventional rougher and scavenger flotation, column cell cleaner flotation, and ceramic disc filtration. The plant was commissioned in August 1994 and quickly reached capacity and expected levels of metallurgical performance. In May 1996, a decision was made to double the capacity of the concentrator by the addition of a second line of equipment. The expanded facilities were commissioned in October 1997, less than 18 months after the decision to proceed, and well within the budget. The original concentrator facilities were replicated or duplicated as much as possible, however, a number of important equipment changes were made to take advantage of industry developments since the original concentrator was designed. These included the use of Eimco 120 m3 (4,200 ft3) cells for rougher and scavenger flotation and the installation of a Svedala VTM -800 Vertimill for regrinding. This paper describes the rationale behind these changes and explores the reasons for the success of the project.

Jan 1, 1999

By D. R. Wright

"The modest thermal efficiency of the steam turbine cycle essentially determines the heat required and, therefore, the coal consumption and ash production of pulverized-coal-fired powerplants. This paper emphasizes how some properties of coal and its ash can crucially affect the operation of a steam generator and its flue gas cleaning equipment. A brief reference to some siting factors and economics reaffirms the all-pervasive influence of the properties of coal and ash and establishes the importance of a firm supply of cooling water. The economics of scale remains a compelling factor in selecting the size of units, despite disappointing performances by some of the larger units. Environmental considerations suggest that smaller units still have a role to play. IntroductionCoal fuelled one industrial and economic revolution, beginning two hundred year s ago . It was the precursor of competing fuels, notably natural gas, oil and uranium, which eclipsed it in terms of convenience and rate of growth.The turmoil that now exists because of rapidly dwindling supplies of no-longer-cheap oil and the concerns about nuclear energy-justified or unjustified-exacerbated by an operating incident at the Three Mile Island Nuclear Powerplant, prompt speculation for a resurgence of coal, especially where it cangenerate electricity to replace energy from imported oil.The world's reserves of coal are not inexhaustible, although they are ample for several decades. Of greater import is the fact that the world's coal reserve s are more widely distributed than its oil reserves, and they appear less convenient as instruments of economic and political persuasion by opportunist powers. The crux is whether or not the world will accept all that a massive, if temporary, return to coal implies.Combustion of pulverized coal in steam generators to pro duce electricity is a 50-year-old, well-understood technique; it is undergoing continuous refinement to meet evolving environmental and economic criteria and is not found wanting. It is certainly the only technique available and technologically advanced enough to replace oil immediately on a large scale. Although it may take a decade to bring a new coal-fired powerplant into service, this delay is a reflection on nontechnical and administrative processes. Capital and operating costs of coal-fired powerplants are significant and subject to inflation, but, because of the accumulated experience in this field, the ability to control costs is better than for those energy processes which are less mature or still in embryo form. More exotic, soft energy systems, touted as the panacea for world energy problems, have still to prove themselves on the scale they are needed and under the stringent climatic and operating conditions coal-fired powerplants have already mastered."

Jan 1, 1980