Search Documents

By Theresa M. Bodus

The strength of roof shales is, in part, a function of the preferred orientation of clay minerals within them. Therefore, analysis of clay fabric under both air-dried and hydrated conditions should be helpful in understanding roof shale failure. Core samples were collected from the Energy, Anna, and Lawson shales, which are locally present as roof shales of the Herrin No. 6 coal of southern Illinois. The Clay Fabric Index (CFI) was measured for thirty core samples, using X-ray diffractomtry, to investigate the relationship between clay fabric and roof collapse in coal mines. Greater CFI values indicate a weaker preferred orientation among clay minerals, which generally results in a weaker inter-grain bond. Average CFI values for air-dried samples were: 0.15 for Anna shale; 0.20 for Energy shale; and 0.37 for Lawson shale, .After the introduction of water, average CFI values increased to: 0.28 for Anna shale; 0.22 for Energy shale; and 0.43 for Lawson shale. The laboratory results indicate the following: [l] under air-dried conditions, Anna shale is the most stable, followed by Energy and Lawson shales; and 121 under hydrous (mine) conditions, Energy shale is the most stable, followed by Anna and Lawson shales. In mine environments where roof failures involving Energy shale have occurred, planar trends delineated by a relatively high density of small (0.2-4 cm diameter) iron concretions have been reported along the failure surface. Radial cracks have been observed around unsealed anchor bolt holes in the Anna shale. Instability of the Lawson shale is ubiquitous in coal mines. In the laboratory, similar physical changes were noted in the shale samples after the introduction of water, including [l] increased hydration around the perimeter of iron concretions in Energy shale, [2] radial extension cracks in Anna shale, and 131 extreme slaking of Lawson shale. Measured increases in the CFI reflect the observed physical changes of the samples upon the introduction of water, which probably reflect changes in strength that may result in roof failures in hydrated mine environments.

Jan 1, 1989

By N Voller, A Ishmurzin, G Hackl, M Wu, A Kharicha, M Chintinne, C M. G Rodrigues, A Ludwig

Slag fuming (SF) is a critical process for recycling zinc-containing slags, but the corrosive nature of molten slag poses challenges to the reactor durability. The freeze-lining (FL) technique offers a solution by forming a protective layer on the reactor wall. It requires intensive cooling using watercooled jackets, which can stabilise the FL while compromising the energy efficiency of the process. This study presents a computational fluid dynamic (CFD)-based model to optimise the SF process by considering FL formation and its impact on heat transfer and reactor wall temperature. A volumeof- fluid (VOF) model is coupled with a mixture continuum (MC) solidification model to capture the intricate multiphase flow dynamics within the SF furnace. Two FL types are considered: FL solidifying on the reactor wall in the slag bath region; and FL solidifying on the reactor wall in the freeboard region. The FL of the first type forms when the slag temperature drops below liquidus temperature. The FL of the second type only forms when a splash-induced slag droplet collides with the freeboard wall and solidifies. A series of splashing events are necessary to coat the freeboard wall. The simulation was run until a global energy balance was reached. This means that the heat losses from the water-cooled jacket, bottom wall, outlet and fuming balance the heat gains from the hot gas injected through the submerged plasma torches. The increase in FL thickness, due to its low thermal conductivity, reduces the heat losses through the reactor walls. The calculated FL thickness and heat fluxes were in good agreement with industrial data, validating the model’s credibility. The simulation results provided valuable insights into the fuming process, including slag bath temperature evolution, slag splashing dynamics, FL formation patterns, local heat fluxes through the reactor wall and overall energy balance. These findings can inform process optimisation strategies to enhance the energy efficiency and sustainability of SF operations. The authors have built a prior version of the model framework and applied it to simulate FL formation in an electric smelting furnace (ESF). The results from both the ESF and the current SF highlight the applicability of such model framework to a range of industrial processes involving FL formation. This model framework can ultimately contribute to more energy-efficient and sustainable industrial operations.

Aug 21, 2024

By J. P. Walker

"INTRODUCTION Sponge iron has been made commercially since 1912 at a Swedish ceramic plant; and the product, known as Swedish disk-type nagger sponge iron, has an excellent reputation as a superior furnace feed wherever high-grade steels are made.The general procedure for making brickyard sponge iron was described frequent in Swedish technical journals before 1932 and at that time consisted in filling clay refractory containers, called saggers, with iron ore plus the necessary quantity of solid reducing agent and then firing in an ordinary ceramic kiln. Two types of sponge iron were made in this way: (1) An inferior, high-sulfur product obtained by mixing the ore and solid reducing agent; and (2) a high-grade, low-sulfur product made by filling the sagger with alternete layers of unmixed ore and reducer, yielding sintered disks of metallic iron particles.Swedish disk-type sponge iron of interest to the steel industry because it has a very low sulfur content, even when made by the use of low-grade, high-sulfur coals for reducing and firing. The Swedish product also contains little siliceous gangue residue and is almost phos¬phorus-free. To those features must be added the high metallic-iron content -90 to 96 percent - and freedom from even small amounts of the metals that are undesirable in steel making.The details essential for successful operation of this procedure are not known, especially as regards improvements said to have been made since 19;2. The Bureau of Mines therefore decided to determine some of these missing details, and this report records the results of the first set of experiments on the manufacture of brickyard or sagger sponge iron."

Sep 1, 1945

Precast prestressed concrete piles designed to be end-bearing in a sand stratum at Drax Power Station met with extremely variable resistance during driving. Some piles came to virtual refusal almost immediately on entering the sand whereas others were driven to considerable penetration with very low resistance. Redriving and load tests on piles experiencing low resistance on initial drive showed that take up in strength occurred over a relatively short period of time. Investigations involving the use of pneumatic piezometers revealed the development of significant excess pore pressures during driving. Samples from boreholes showed that piles met the least resistance when the sand had a high silt content. Comparison with the original site investigation data demonstrated the difficulties in predicting detailed pile behaviour. The varied behaviour could not be related to the original borehole logs or to SPT or static cone penetrometer results. The factors controlling pile driving behaviour were essentially geological and could only be explained with reference to local soil grading.

Jan 1, 1989

During the course of the major research in the Metallurgy Department of the University of Melbourne into the creep characteristics of lead and .its dilute alloys, it has been the practice to prepare the majority of test specimens from rolled strip. From time to time during the progress of the work, certain variables involved in. the rolling of the experimental ingots have been investigated. It is proposed to collect together in this paper the results of these experiments. Some general features relating to the type of deformation produced have been discussed in a previous paper.While it is admitted that the conditions prevailing through this work differ' in some respects from those of industrial rolling practice, it is felt that many of the factors investigated have an important practical significance. Some of the work described forms a continuation of the researches of R. S. Russell (2) , (3) , (4), into the recrystallization of various pure leads after deformation by rolling.MATERIALS USEDIn this work, a variety of "pure" leads and certain dilute alloys made from the purest of the basis leads have been studied. The compositions of the basis leads and the corres...

Jan 1, 1940

By Aram Grigoryan

This paper addresses historical aspects and construction sequencing of the subway complex under Columbus Circle in Manhattan; the structural elements of the rehabilitation and new construction; and the challenges associated with design and construction. PB is providing engineering services to New York City Transit (NYCT) for the rehabilitation of the 59th Street/Columbus Circle Station Complex that services over 150,000 customers daily. The project involves structural repairs, modifications and new construction requiring underpinning and temporary supports, custom framing details, and construction staging procedures to meet stringent limitations within the operating transit station and around the Columbus Circle street intersections.

Jan 1, 2008

By M. Jeffrey

This study investigated the elution of precious and toxic metals from activated carbon. Gold and mercury are of primary interest, due to their value and environmental impact respectively. A laboratory elution rig was commissioned to simulate industrial Zadra and AARL carbon elution conditions. Mercury was found to elute most effectively in strong caustic cyanide solutions; gold was found to elute most effectively in hot low ionic strength solutions. As cyanide decomposes on contact with activated carbon at high temperatures, optimum elution conditions for gold conflicts with those for mercury?no practical compromise in conditions was found. However, sequential elution allowed reasonable recovery of both metals. Ongoing work is looking at the deportment of other metals under elution conditions.

Jan 1, 2009

By D Mnller, J L. Mauk

The Oblaga Cu-Au skarn deposit and porphyry prospect is located in the south-eastern edge of the Gobi Desert in western Inner Mongolia. The deposit occurs within metamorphosed middle Paleozoic volcanic, plutonic and sedimentary rocks.   Ivanhoe geologists recognise eight main rock types in the area. Calcareous sediments include conglomerate, interlayered siltstone-sandstone, and limestone. Covering the calcareous sediments is a slab of thrusted biotite granite, and above it is rhyodacitic lithic tuff which, in places, is overlain by alluvial sediments. Various plutonic rocks and related intrusion breccias have intruded these units. Monzodiorite, quartz-monzonite and monzonite tend to form thin, high-angle intrusions and the youngest andesitic intrusions are generally wider and subhorizontal.   The Oblaga Cu-Au skarn, which occurs in the calcareous sediments, shows typical prograde and retrograde mineralogy. Petrographic studies show that prograde skarn minerals have been overprinted by retrograde skarn minerals, and original host rock minerals have been texturally obliterated and completely replaced. The mineralogy of the Oblaga skarn deposit is very similar to other Cu-Au skarn deposits worldwide.   Sericitic and minor chloritic alteration occurs throughout the study area and may relate to porphyry-style mineralisation. Generally, this alteration is not intense and most rocks have retained their original texture. Geochemical analyses suggest that K-metasomatism is not widespread at Oblaga. XRD analyses suggest an upward and outward transition from sericitic to chloritic alteration.   Comparisons between Oblaga and other porphyry Cu-Au deposits worldwide show that Oblaga has very similar characteristics to deposits that have undergone sericitic alteration. However, Oblaga is special because it also has relatively intense chloritic alteration, which is uncommon in other porphyry Cu deposits described in the literature.

Jan 1, 2005

By Nikhil Dhawan, Veeranjaneyulu Rayapudi

This study investigates upgrading of low-grade banded hematite quartzite iron ore (Fe ~31%). Conventional beneficiation was found to be futile. The susceptibility of iron phases to microwave exposure and their selective absorption assists in the liberation of iron values. Microwave exposure of coarse particles at 540 W for 10 min yielded a concentrate with Fe 56.30% and recovery of 50.68%. Conventional carbothermic reduction at 500 °C, 60 min and 9% charcoal yielded a concentrate with Fe 57.6% and iron recovery of 68%. The presence of sufficiently bonded silica leads to an easy formation of a fayalite phase. The microwave reduction design yielded FeG of 57.6%, FeR of 47% and a yield of 24% at an optimal condition of 540 W, 8 min and 6% charcoal. It was found that a small fraction of microwave-irradiated ore-charcoal mixture melted rapidly, and pure ferrite balls were observed within 8 min. An optical micrograph of a ferrite ball reveals the retained austenite and martensite phase.

By Fennell B

A process for the recovery of cobalt from a speiss produced at Sulphide Corporation is presented. The speiss is leached in oxygenated sulphuric acid to dissolve the metallic iron at a pH of around 4. The resultant iron (11) is subsequently oxidized in the leaching vessel and precipitates as goethite. Acid is regenerated in the precipitation allowing dissolution of further speiss. Subsequent to the conversion of most of the iron in the speiss to goethite, conditions become sufficiently oxidizing to dissolve cobalt. Cobalt is not co-precipitated under the leaching conditions, yielding a pregnant solution containing the cobalt and some iron (11). The principal advantage of such a process is the significantly lower acid consumption over that obtained by complete dissolution followed by selective precipitation. An impure product of cobalt hydroxide can be obtained from the pregnant solution by neutralization.

Jan 1, 1983

By Eustáquio Vieira Junior

O Alto-Forno 3 da Usiminas, em Ipatinga, possui três regeneradores de câmara de combustão interna e passou por sua última reforma em 1999. Nessa reforma, não foram realizadas alterações de projeto nos regeneradores, sendo somente substituídas as fiadas superiores da parede de partição entre as câmaras de combustão e de regeneração e do checker, que se encontravam desgastadas. No decorrer de 2007 e nos anos seguintes, verificou-se a queda de tijolos refratários na região localizada acima do queimador cerâmico do Regenerador 7. Durante o processo investigativo, adotou-se a inspeção por videoendoscopia a partir de 2010. Face à deterioração da região onde se concentravam as quedas de tijolos e à postergação da reforma do Alto-Forno 3, decidiu-se pelo reparo a quente deste regenerador. O trabalho apresenta o histórico das ocorrências no Regenerador 7, as intervenções anteriores ao reparo, o planejamento e os resultados obtidos a partir da operação com dois regeneradores e o desempenho dos regeneradores do Alto-Forno 3 após o reparo a quente no Regenerador 7, mostrando a eficiência do reparo realizado.

Aug 2, 2018

By Jose a. Sanchidrian, Ramon G. Eguren, Javier L. Amigo

On December 2013 a MEMU exploded at a blasting site in Norway, after burning for more than two hours. This paper describes the analyses made to determine the actual yield of the explosion, the lessons learned from the event and the actions taken as a consequence. The conclusions of the analysis were the following: - The yield of the explosion was 650-1450 kg TNT. In terms of AN and ANE they correspond to 1300 – 3700 kg AN, or 950 – 2450 kg ANE or ANE/AN blend. These quantities are 8 to 31 % of the explosive precursors in the truck. The burning of the truck and its load for two and a half hours had consumed more than two thirds (perhaps up to 90 %) of the explosive precursor material.

Jan 1, 2016

By Hudson S. B

With a particular electrode configuration, and a particular combination of electrode voltage and roll speed, a relatively small increase in electrode voltage, or a relatively small decrease in roll speed, resultsin a marked improvement in the separation of zircon from ilmenite. In general, fine minerals can be separated using a higher roll speed, or a lower electrode voltage, than is required to separate coarse minerals. The ionizing electrode should be reasonably close to the point at which mineral is fed on to the roll, and nearer to the roll than the non-ionizing electrode. The optimum conditions for the separation of zircon from ilmenite may not apply for the separation of other non-conductors from other conductors.INTRODUCTIONAlthough the high tension separators used in the Australian beach sand industry are efficient, this efficiency has been gained very largely by a process of trial and error, and not by a systematic study of the effects of changes in the operating variables. The optimum roll speed for a particular electrode position and electrode voltage, and the optimum electrode voltage for a particular roll speed and electrode position, can both be determined quite readily. It is not so simple to determine the optimum electrode position for a particular electrode voltage and roll speed. The reason for this is that the electrode used in high tension separators consists of two parts-an ionizing and a non-ionizing electrode respectively. The angular and radial positions of these electrodes, relative to the feed roll and to each other, affect the behaviour of conductors and non-conductors to varying degrees.

Jan 1, 1962

By Marianne Snedeker

In September 1985 we published a questionnaire asking about the content of MINING ENGINEERING and about your interests. By Dec. 10, our cutoff date, we had 430 responses, representing about 1.5% of the 28,238 people who received the September issue of ME. In the data that follow the tabulation and percentages are based on the number of individuals who responded to the particular question. About ME Through responses to the questionnaire, we were hoping to learn more about you, your interests, and how the magazine could better serve you. Those of you who responded told us something positive - you look at or read the magazine. Of the 430 respondents, 428 or 99.5% indicated that they had read or looked through the July and/or August issues. Those of you who refer to the magazine once are 207 or 48.5%. Those of you who refer to the magazine two or three times are 193 or 45.2%. Those of you who refer to the magazine four or more times are 27 or 6.3%. How much time do you spend reading the magazine? Of those responding to this question: 64 spent up to 1/2 hr 15.0% 224 spent up to 1 hr 52.6% 115 spent up to 1-2 hr 27.0% 23 spent more than 2 hr 5.4% In an informal survey among our staff, we determined that most people spend 1/2 to 1 hr reading magazines to which they subscribe at home. Does that match your experience? Many of you, 335 or 79%, clip your magazine for further reference. Also, many of you, 313 or 73.6%, do not pass your copy on to another reader, indicating that you are clipping it or receiving the magazine at home. Those magazines that are passed on reach: 1 person 3 0.7% 2 people 64 15.1% 3-5 people 34 8.0% 5 or more 11 2.6% Answers to what portions of the magazine you find useful indicated that the top three were Industry Newswatch, feature articles and Technical Papers; see Table 1. The "other" category included advertising - display, classified, Employment, and Professional Services - Washington Survey, New Products, Free Literature, book reviews, technology news, and Coming Events and Short Courses. We asked your appraisal of the technical level of the magazine. Of those responding, 39 or 9.1% indicated that it is too technical, 55 or 12.8% indicated it is not technical enough, and 335 or 78.1% judged it to have the correct technical level. In response to the question about whether you like to read an occasional feature that is not technically oriented, 21 or 5.1% said no, but an overwhelming 94.9% (393) said yes. Of the specific

Jan 1, 1986

By J. H. Daniel, S. Krzemien

Partners In Economic Reform, Inc., established a Polish-American Mine Center in Katowice, Poland, in 1996 to improve working conditions in the minerals industry. The program was based on the experience of mining companies, government, and labor in the United States, and was executed by a Coordinating Committee headed by the Center Director and Polish leaders from industry, State, labor, and academia. The cooperation among all parties has enabled safety and health issues to become part of industry restructuring with impressive initial reductions in coal mine fatalities. Existing work practices and attitudes of labor and management were assessed in coal mines throughout the country. Promotion, Rules, and Job and Task Analysis were identified as the areas requiring the most improvement, and are part of a post-graduate Safety Management program. Demonstration projects included measuring dust levels, using safety glasses, and promoting hazard awareness. Improved labor-management relations increased cooperation allowing for effective transfer of technology. Results can also be applied to improve the working environment of the manufacturing sector also undergoing restructuring.

Jan 1, 2001

By Jonkion M. Font

As a comprehensive contribution to the understanding of oxygen-blowing of matte smelting, the copper and nickel solubilities between the FeOx SiO2-MgO slag with saturated SiO2 and the Cu2S-Ni3S2 FeS matte with the NCu/(NcU+NNi) of 1, 0.75, 0.5, 0.25 and 0, in a MgO crucible were investigated at 1573 K under controlled partial pressures of SO2 at 0.1, 0.5 and 1 atm. The partial pressures of SO2, S2 and O2 were controlled by using an Ar-SO2-S2 gas mixture after passing through a sulfur reservoir. It was clarified that, at a given matte grade, the solubility of copper in the slag was independent of pso2 while that of nickel increased with increasing pso2. This notable difference was considered to be ascribable to the chemical formulas of the mono-metallic sulfides in which one copper atom combines with ½ sulfur atom while one nickel atom combines with 2/3 sulfur atom. It was also clarified that, at a given iron content in the matte, the pot and ps2 were independent of the matte species. This was ascribable to aFeS in the matte, which was independent of the matte composition, Ncu/(Ncu+NNi), at a given iron content in the matte.

Jan 1, 1999

By J. Hartikainen

Kemi cardboard mill is founded on the alluvial bed of Kemi river at the north-eastern cost of Botnic Culf in Northern Finland. The alluvium consists of sandy and silty layers underlain by thick medium dense silty moraine layer. The first cardboard machine, having a belt width of 7,4 m, was constructed in 1972 on 7,5 to 9,5 m long wedge-shaped precast driven piles. Because of the excessive differential settlements and sometimes unexpected dynamic malfunctioning of the machine it was decided to strengthen the foundation before installing the partly new machine and increasing the running speed from 500 to 750 m/min. Piling was done under extremly strick limitations concerning space, vibrations, settlements, dust etc. Extra vertical support was made by using 23...25 long x-form steel piles driven by compressed air pile hammer down to rock. The piles were held together with old piles by a conctrete frame with diagonals, which made the total system - machine - foundation frame, piles and ground - ridgid enough to avoid resonance during dynamic loading.

Jan 1, 2010

By E. F. Johnson, V. O. Naumann, D. P. Bossler

A method is presented for calculating individual gas and oil or water and oil relative permeabilities from data obtained during a gas drive or a waterflood experiment performed on a linear porous body. The method has been tested and found both rapid and reliable for normal-sized core samples. INTRODUCTION Individual oil and gas or oil and water relative permeabilities are required for a number of reservoir engineering applications. Chief among these is the evaluation of oil displacement under conditions where gravitational effects are significant, such as a water drive or crestal gas injection in a steeply dipping oil reservoir. Numerous proposed methods of obtaining relative permeability data on reservoir core samples have been too tedious and time consuming for practical use, or have yielded questionable and sometimes inconsistent results. A method has been developed by which the individual relative permeability curves can be calculated from data collected during a displacement test. The method is based on sound theoretical considerations. Using this method, with a properly designed experimental procedure, relative permeability curves can be obtained using core samples of normal size (i.e., 2 to 3 in. in length and 1 to 2 in. in diameter) within a few days after receipt of the core. In a recent publication D. A. Efros1 describes an approach to the calculation of individual relative permeabilities that is based on the same theoretical considerations. We believe the approach described in the present paper is more adaptable to practical application than the method implied by Efros. In addition, comparisons with independently determined relative permeabilities are furnished to substantiate the reliability of the new method. DERIVATION Previously the theory of Buckley and Leverett as extended by Welge2 as been used to calculate the ratio of relative permeabilities. In the derivation which follows, this theory is further extended to permit calculation of the individual relative permeabilities. The theory assumes two conditions which must be achieved before the method is applicable. They are that the flow velocity be high enough to achieve what has been termed stabilized displacement,3 and that the flow velocity is constant at all cross sections of the linear porous body. In stabilized displacement the flowing pressure gradient is high compared with the capillary pressure difference between the flowing phases. The high pressure drop insures that the portion of the core in which capillary effects predominate will be compressed to a negligibly small fraction of the total pore space. The assumption of constant flow velocity at all

An efficient and portable mathematical model has been developed for simulating heat transfer in six-in-line slag-resistance-heating electric furnaces for smelting sulphide ores to produce base metals and platinum group metals. This model is a steady-state one relating furnace conditions and performances to various control and input parameters. Some transient effects occurring in electric furnaces are neglected for computation efficiency. This article describes the model development and modelling results. The present model is capable of predicting: (i) temperatures at various locations in a six-in-line furnace, such as slag bath, matte bath, solid charge, freeboard space, freeze lining, cooling water, and air gaps between solid material components, etc. (ii) freeze lining thickness, (iii)smelting rate, and (iv) heat loss rate, etc. A typical feature of the model is that it is easily portable to different application platforms and sufficiently efficient with execution times less than a few seconds. Therefore, it is possible to apply the model for online prediction and control of heat transfer and freeze lining thickness in industrial electric furnaces.

Jan 1, 2011

By H. A. Lequear, J. D. Lubahn

A sudden change from one constant strain rate to another during a tensile test causes an unusual transient in aluminum alloy 61ST. A sudden change from one constant stress to another during a creep test does not produce an unusual transient in this material. A specially devised test shows that the nature of the previous steady-state conditions, which the sudden change disturbs, is one of the factors affecting the transient behavior. Some of the observations may be explained in terms of strain aging. USUALLY a sudden change during a tensile test from one constant strain rate to another causes a small, abrupt vertical shift from one stress-strain curve to another, parallel one. This behavior is apparently characteristic of all metals at very low temperatures and of many metals for wide ranges of temperature. It is illustrated in Fig. 1 for some early data on 61ST tested at — 195oC, and in Fig. 2 for some recent data on copper at room temperature. The greater accuracy of the results of Fig. 2 over previous ones' is due to the equipment shown in Fig. 3. Three levers apply the bulk of the load, while the changes in the small remainder load are indicated sensitively by a low capacity load scale. Refs. 2 and 3 describe the recording equipment. A test like those in Figs. 1 and 2 provides the information necessary to determine the rate sensitizrity, n,4 of the metal. ( a log s ) ? log s n = ------------------------ ----------------------------= ( a logs e, ? log e logS2-logS1 log S2/S1 log i2 — log e1 log e2/e1 where S equals stress: e is logarithmic strain or natural logarithm of (final gage length/initial gage length);" i is strain rate or de/dt: and n is rate sensitivity, rate of change of log stress with log strain rate at a given strain, or (a log S/a log i),. Normally, the rate sensitivity, n, is positive, which means that an increase in stress causes an increase in rate. However, certain exceptions, attributed to strain aging,5 have been observed. Fig. 2 indicates how rate sensitivity values are derived from the measurements. Table I summarizes the rate sensitivity values derivable from Fig. 1. In contrast to the behavior of copper in Fig. 2, the aluminum alloy 61ST, which strain ages when tested near room temperature, exhibits an unusual transient when the strain rate is suddenly changed,' as shown in Fig. 4. Initially, there is a comparatively sudden vertical shift of the stress-strain curve in a direction corresponding to the rate change, but then the curve gradually shifts back again. The initial shift is not as sudden as might be expected, because the testing machine is unable to achieve the impressed rate change instantaneously, as illustrated in Fig. 2. The behavior shown in Fig. 4 will be referred to as a tensile transient, the word tensile implying that the behavior was observed in a tension type of test. The corresponding test, where the strain rate is maintained constant except for the sudden change, will be called a tensile transient test. A creep transient, by contrast, will be defined as a temporarily abnormal behavior in a creep transient test, where there is a sudden change from one constant load to another.' In Fig. 4, a naive look at the gradually decreasing and then increasing load after a sudden rate incre-

Jan 1, 1957