Search Documents

By Lori A. Simpson

Mission Bay is a 300-acre reclaimed site in San Francisco, California, that is currently being redeveloped. Plans include new neighborhoods, parks, a new University of California, San Francisco, research and development campus, a biotechnology campus, and commercial office buildings. New infrastructure is being constructed throughout the site, consisting of utilities, pump stations, and roadways. Previously, Mission Bay was a part of the San Francisco Bay. Reclamation of the shallow bay coincided with the booming development in San Francisco in the 1880s and continued through 1920. Subsurface conditions are extremely variable throughout the site. The stratigraphy generally consists of 5 to 45 feet of fill, up to 140 feet of weak, compressible clay (?Bay Mud?), dense sand, stiff clay, and bedrock of the Franciscan Complex that has been encountered 5 to 210 feet below the ground surface (bgs). Geotechnical issues related to these subsurface conditions include liquefaction, lateral spreading, settlement, and adequate foundation support. This paper presents case studies of the geotechnical aspects of design and construction of several buildings in Mission Bay, highlighting the similarities and variability in the subsurface conditions and the different conclusions and solutions developed for each project. The case studies will include: 1) a building supported on steel H-piles where the depth to bearing varies from about 70 feet bgs in one half of the site to 165 feet bgs in the other half; 2) a building supported on precast, prestressed, concrete piles bearing in a thick, very dense sand layer; 3) a building with over 100 feet of Bay Mud supported on 120- to 180-foot-long PCPS concrete piles driven to bedrock adjacent to buildings supported on steel H-piles driven to bedrock; and 4) sites where auger pressure grouted displacement piles (APGD) and Tubex piles were installed. Case studies will include results of pile driving analyzer (PDA) testing and static pile loads tests, where performed.

Jan 1, 2006

Since its inception in 1962, the Julius Kruttschnitt Mineral Research Centre has adopted the view that an effective method of training highly qualified engineers for the mineral industry is the pursuit of postgraduate research programmes conducted in operations, that is, in the mines and processing plants of the industry which the research serves. The paper describes how this is achieved in practice, at little or no cost to the taxpayer, and explores the strengths and weaknesses of this approach in the context of a dual mission for the Centre: 1. The postgraduate training of engineers for the mineral industry. 2. The production of useful R &I) for the mineral industry. Topics discussed include financing, relationships with industry and Government, the maintenance of academic excellence, research style, the marketing of research, and limits to growth.

Jan 1, 1989

By G. Caron, M. Boisclair

In 2005, CANMET-MMSL used its pool of expertise in ground control, open pit and underground mine engineering, mineral processing, information technology and applied mineralogy to launch a mine-to-mill research project. The objective of the project was to optimize the distribution of rock breakage energy among blasting, crushing and grinding activities, thereby maximizing the efficiency of energy utilization within comminution processes. Tests were designed to demonstrate that this approach could reduce the energy consumption, thus contributing to the reduction of Green House Gas (GHG) production in the Canadian mining industry. The project was accomplished in collaboration with DynoConsult and Dyno Nobel Canada Inc., a world leader in commercial explosives. Data analysis from 12 blasts (six with electronic and six with pyrotechnic detonators) in three different geological formations of a quarry (soft, medium and hard rock) shows that electronic blasting technology increases rock fragmentation by 15% (in hard rock) to 20% (in soft rock). A more uniform rock fragment size distribution is also obtained. The impact of the improved quality blast product on downstream processes of the quarry is a productivity increase of 5% in rock excavation and transportation, an energy reduction of 10% at the primary crusher and an increase of 15% of the primary crusher throughput. A soft-sensor prototype, based on primary crusher data (i.e. energy consumption, throughput, feed and product size distribution) and a simplified computerized process model, was developed for on-line measurement of the rock operating work index. Additionally, 385 rock samples and specimens were collected and prepared to determine the tensile and compressive strength of the rock material, to evaluate the aggregate crushing work index, and to examine the development of micro- and macro-fractures by means of binocular and SEM microscopy. Blast-induced rock damage was evaluated at the end of the laboratory testing program. Even though a reduction of rock hardness of around 30% was observed after blasting, the impact of the blasting method (i.e. use of electronic or pyrotechnic detonators) on the induced rock damage could not be observed. It is either absent or not perceptible with the accuracy of the measuring techniques and the number of samples analyzed.

Jan 1, 2007

Underground Mine Drainage may be conveniently divided into two operations:(a) Collecting and transporting drainage water to the pump eastern.(b) Elevating water to the surfacc by pumping.This short paper describes a system which automatically performs operation "a" and which has been developed on the South mine at Broken Hill, under the supervision of the mine foreman, Mr. F. McDonell. Operation "a" does not come under the heading of "subsidiary mine" drainage.SUMMARY(1) All drainage waters are collected by gravity flow into sumps.(2) Automatic control boxes operate syphons which transfer water from level to level to pump cisterns or to feed water service.EQUIPMENTSyphon Control Boar - Constructed of 10 ft. x 2 ft. oregon timber, suitably bolted together and equipped with a Bailey's cistern valve, with copper ball float control, and 12 in. pipcs and fittings forming a syphon (Fig. 1). One of these boxes is placed on each level at the shaft.The valve and float are so arranged that when the float is up (ie, box full) the valve will be fully open, and when the float is down (ie, box empty) the valve is closed. The vertical range between the cxtreme positions can be altercd by lengthening orshortening the adjustable arm of the float. The ideal valve is one...

Jan 1, 1927

By Alan G. MacKinnon

Loads and stresses from pile driving are increasing from heavier piles and more powerful hammers. Stresses can be dangerous to equipment stability. Equipment developer MacKinnon tells how to compute stresses for all positions of the crane boom and angles of pile batter. From a paper presented at the DFI-University of Hawaii Seminar, April 1985.

Jan 1, 1986

By C. R. McClung

"Molybdenum, in the form of molybdenite, is a common byproduct of many copper mining and concentrating operations. While the recovery of most copper sulfide minerals is principally liberation controlled, the recovery of molybdenite is much more complex, with fully liberated particles commonly lost to tailings.A geometallurgical investigation was undertaken of molybdenite from the Bingham Canyon deposit with the aim of determining what effects, if any, mineralogy and the mineralogical attributes of morphology, angularity, liberation and size have on molybdenite recovery in the processing circuit. A set of samples was collected from the ores and products of Rio Tinto Kennecott’s Copperton Concentrator. The samples were analyzed by normal polarized reflected light microscopy, X-ray diffractometry, and scanning electron microscopy using a Mineral Liberation Analyzer, revealing the presence of two distinct types of molybdenite, which are the two polytypes: hexagonal (2H) and rhombohedral (3R). The 2H polytype occurs as textbook-shaped particles in quartz-molybdenite veins located in the core of the deposit, while the 3R polytype occurs as disseminated, ball-shaped particles with a dull or frosted appearance along the margins of the mineralized intrusive body or central core. Each polytype exhibited metallurgical properties consistent with those reported in the literature. The 2H polytype is easily ground, kinetically “faster” floating and displays surface attributes that are amenable to higher rates of recovery. This commonly results in the production of a high-quality molybdenum concentrate under normal operating conditions at most copper concentration operations. The 3R polytype is difficult to grind, kinetically “slower” floating and displays surface attributes that are less amenable to recovery. Therefore, in deposits with higher concentrations of the 3R polytype, modifications to operating parameters may be necessary to improve the recovery of molybdenite.A preliminary investigation into the metal budget of porphyry copper and molybdenum deposits indicated a possible positive correlation between total economic metal budget and polytype content. Higher concentrations of the 3R polytype appear to be more prevalent in gold-enriched porphyries than in molybdenum-enriched porphyries. This may help explain why it is easier to obtain higher rates of recovery in molybdenum ± tungsten-rich deposits, which contain little to none of the 3R polytype. There is a potential for the metal budget of a porphyry deposit to be used as an indication of the molybdenite polytype present as well as its impact on the economics, in terms of exploration, and the processing circuit, in terms of plant design."

Jan 1, 2016

Very few of those occupied in pursuits other than mining have any conception of the extent of boring operations that have been carried out on the gold and coal fields of Victoria, or of the valuable and definite knowledge obtainable by such means. The subject comprises various branches, which it will be necessary to describe in detail. The three main divisions are The Administrative, which includes all financial work and general management. The Professional, dealing with topographical and geological work necessary before any scheme of boring can be laid out, the preparation of plans, the inspection of cores obtained from bore holes, the examination of diamonds, etc. The Mechanical Branch, dealing with the drilling machinery, setting of diamonds, maintenance of stores, etc. In 1877, the Goverpment of Victoria decided to assist in prospecting the mineral resources of the colony by the aid of diamond drill boring, and for that purpose, a vote of £5,000 was passed, with which were purchased three diamond dulls, an American type being adopted.

Jan 1, 1901

By D. A. Bruce

The Deep Mixing Method is a very valuable tool for combating problems related to in situ soil treatment, improvement, and retention. Many different variations are used throughout the world, and there is a correspondingly rich technical literature on the testing and properties of the treated soil. This paper provides a synopsis of these aspects.

Jan 1, 2001

The following list contains the names of members of whose deaths notices have been printed in MINING AND METALLURGY during the year ending April 1, 1938. Biographical sketches published in MINING AND METALLURGY are indicated in the last two columns. YEAR OF ELECTION - NAME - DATE OF DEATH ? ISSUE CONTAINING BIOGRAPHY - PAGE 1908 - ARCHBALD, JAMES, JR - July 24, 1937 - March 1938 - 168 1934 - BAECKCTROM, OLOF - Oct. 9, 1937 - March 1938 169 1918 - BAKER, HARRY A - May 28, 1937 1916 - BANDY, PERCY 3 - April 19, 1937 1916 BARKDOLL, I. H Dec. 1, 1937 Feb. 193S 121 1936 BARNETT. PETER T Jan. 27. 1937

Jan 1, 1938

By Richard P. Reiff

"The Facility for Accelerated Service Testing (FAST) program has been involved in numerous rail wear tests since its inception in 1976. A number of specialized tools have been developed to aid in assessing specific performance parameters including gauge face wear, head height loss, metal flow, head area loss, hardness, and welded rail end batter. The layout of a test site, including position in curve, number of measurements per rail, and train operation must be properly controlled/monitored to provide valid wear comparisons.This paper will provide an overview of the above-mentioned tools and techniques. In addition, a summary of recent test results from FAST, including information on head hardened rail investigations, will be provided. A set of guidelines for establishing a revenue service field test site will also be provided to aid users in performing evaluations of their own.IntroductionBackground of Rail Wear Testing at FASTThe Facility for Accelerated Service Testing (FAST) located at the Transportation Test Center, (TIC), Pueblo, Colorado has been involved with testing of rail since program initiation in 1976. A huge data base of rail wear information has been gathered from FAST operations under a variety of rail metallurgies, lubrication conditions, and measurement techniques. Attempts at obtaining meaningful rail wear information from early (1976-1978) FAST rail wear data was hampered by two main factors: (I) measurement techniques were insufficiently accurate for the amounts of wear being experienced, and (2) the lubrication was not sufficiently controlled to obtain uniform conditions for a sufficient measurement time period.Subsequent test periods were operated with improved measurement techniques and controls that ensured statistically valid data. The policies and conditions that permit accurate rail wear assessment will be reviewed and outlined in this paper, along with some specific TIC and field examples that will allow the user to improve the accuracy of a field rail test on their own operating property."

Jan 1, 1988

By T. C. Eisele

The use of column flotation was considered for the ?reverse flotation? of iron ore, where the gangue (quartz) was recovered in the froth product. This use of the froth for carrying the gangue mineral rather than carrying the valuable concentrate significantly changes the operational requirements of the column. The objective of this work was to determine which of several column flotation technologies would be most suitable for this type of flotation operation. Studies were carried out using both the Jameson column and the Deister column. Comparative results are presented that show the capabilities of both column types in this application relative to conventional Wemco flotation cells. Columns were demonstrated to have grade-recovery performance superior to what could be achieved with conventional cells. Two-stage flotation with the columns could produce a concentrate that was up to 70.2% Fe at 87.5% iron recovery, compared to 70.4% Fe at only 77.7% iron recovery for four stages of flotation in conventional cells. It was shown to be particularly important to operate the columns to recover a maximum of the quartz gangue into the froth. It was noted that there are often problems in scale-up of laboratory columns to plant scale, because the increase in height and the decrease in the ratio of height to diameter at the larger scale allows more axial mixing and bubble coalescence, both of which degrade the column performance. Horizontal baffling was shown to improve column performance by reducing axial mixing and breaking up large bubbles, and so the use of such baffles in the reverse flotation application was investigated.

Jan 1, 2007

By A. M. Khan, I. Fatt

A new type of steady-state thermal conductivity apparatus is presented and described. Results of measurements on Berea sandstone, Solehofen limestone, Bandera sandstone and Bakelite are presented. The measurements were made in a two-hour period at temperatures up to 80C and axial stress to 125 bars. Results show that the thermoelectric heat pump and tbermistor-controlled electric heater can be used in a steady-state apparatus for measuring thermal conductivity of mck. Steady-state is reached within two hours. With Urethane foam insulation, not more than 3 per cent of heat is lost by radial flaw. The apparatus can be used as a comparator or for absolute thermal conductivity determinations. INTRODUCTION Calculations of heat flow through the earth, both for scientific purposes and engineering design, require thermal-conductivity data on rock. However, the high variability of rock often makes handbook thermal-conductivity data of little value. For engineering purposes in particular, it is desirable to have measured data on samples of the rock mass under study. Laboratory methods for measuring thermal conductivity of rock use either time-dependent1-3 or steady - state temperatures .4,5 The time -dependent (transient) techniques give thermal diffusivity from which thermal conductivity can be calculated if the specific heat and density of the sample is known. Most transient techniques require lengthy and involved sample preparation. Also, the accuracy tends to be low. Steady-state techniques are more exact and are the most commonly used. The steady-state methods, however, also have their difficulties. A long time is often required to reach steady state, troubles have been encountered in establishing good thermal contact between the heating and cooling elements and the rock sample, and unaccounted-for heat losses are difficult to prevent. In this paper we present a description of a new type of steady-state thermal conductivity apparatus. With it, measurements have been made in two hours at temperatures up to 80C and axial stress to 125 bars. Sample preparation is simple and no thermal conductivity standard is needed.6 APPARATUS Our steady-state apparatus is an improvement . over the conduction pile used by Zierfuss and van der vliet4 and Somerton.5 A linear heat flux is established through a conduction pile consisting of the rock sample and a standard material of known thermal conductivity in series. The thermal conductivity of the sample is calculated from the ratio of the temperature drop across the sample

Jan 1, 1966

By Muir DM, Ritchie IM, Gibbons SL

Fundamental studies on the transformations of iron oxides have been carried out and related to the solution conditions in the Becher Process. The results show that a number of iron oxide interconversion reactions occur in the aeration reactor with the products depending on the pH, temperature and oxidation potential of the aeration liquor. It is concluded that the lack of process control in the aeration reactor of the Becher Process significantly hinders the ability to predict and produce high quality single phase iron oxides of a consistent colour.

Jan 1, 1989

By McKinnon R. L

Laboratory and field work on the use of wetting agents for suppression of colliery dust is described. Although the results were inconclusive they were not discouraging and further investigation is required. The use of certain wetting agents may constitute a healthhazard.INTRODUCTIONCoal dust presents explosion and health hazards to the coal mining industry. The problem of dust suppression is particularly acute where water alone is unsatisfactory for this purpose. The addition of a surface active agent (wetting agent) to the water should enable the dust particles to be more easily wetted and thus more easily prevented from entering and spreading through the mine atmosphere.Investigations into this effect carried out at The University of Sydney mainly under research grants from The Joint Coal Board (Dawson and Hargraves, 1955; Charlton and Curnow, 1957) are summarized, and information on the possible harmful effects of certain wetting agents is given.Twelve local manufacturers and five importers supplied 52 wetting agents in liquid, solid, powder, and paste form.The active material content varied from approximately 10 per cent to 100 per cent and the cost per pound from 8d. to 14/3.LABORATORY TESTINGPossible test methodsThree methods of laboratory testing were considered.1. The standard method for comparing wetting agents is the Draves test, used in the textile industry on cotton...

Jan 1, 1961

By Peter Faust, Jeremy Zorne, Timothy Siegel, Diane Fiorelli

Professional sport venue construction follows a very simple rule. Once the decision has been made to move the team to a new place, construction shall begin immediately, so that not more than one or two seasons pass by stuck in the old home. Such tight construction schedules require a different approach than traditional design-bid-build contracts. Design is mostly done on the fly, the construction schedule becomes a main risk factor and an early contractor involvement is desired. As specialty contractors become more and more sophisticated, owners, their construction managers or the general contractor have realized the value of ideas and modern technology they can bring to the table for a successful and fast project completion. Local knowledge and experience in a variety of solutions play a key role in the specialty contractor’s ability to provide added value to the project. This is also true for the specialty foundation contractor, who needs to understand the complexity of such modern structures from its integrate foundation, over the delicate concrete structure to a potentially fancy movable stadium roof. Not to mention all the modern high tech equipment which shall make such a place a great customer experience. His expertise shall enable him to propose the most suitable foundation element for the given ground condition and application. Rather to build what others have designed, his strength is to propose alternate concepts which will be faster and (hopefully) more cost effective. This paper highlights different value engineering (VE) input a specialty foundation contractor had on 3 major sports arena projects in California. Together with the entire team from owner to GC, including the Geotechnical (GEOR) and the Structural Engineer of Record (SEOR), the most efficient and best performing foundation solution can be found every time. But such an approach also requires the open mind of the owner to entertain last minute changes when the permit drawing set has already been submitted for approval.

Jan 1, 2018

By G Veillette, B Parker, S Hart

This paper provides a history of the challenges that were experienced while treating both the clayey oxide gold ores and the supergene copper-gold ores at the Boddington Gold Mine during the period 1989 to 2001. However the bigger challenge was to find a process flow sheet that would allow the economic treatment of the large low-grade competent gold-copper resource that underlies the oxide and supergene gold resource. Metallurgical test work and engineering studies on this resource started in the mid 1990s and culminated in the approval in 2006 of the 35 Mtpa Boddington Expansion Project to treat this material. The process flow sheet provides the basis of an energy efficient comminution circuit that includes high pressure grinding rolls and a treatment circuit with gravity separation, flash and conventional flotation to produce a precious metal low-grade copper concentrate followed by cyanide leaching of the rougher-scavenger and cleaner tailings streams. The treatment circuit allows maximum removal of copper minerals prior to cyanide leaching and so provides an environmentally responsible tailings disposal circuit.

Jan 1, 2007

The disasters between 1920 and 1979 in coal mines in Queensland and New South Wales due to underground fire, gas or coal dust explosion or to gas or coal outbursts, have been assessed. The evidence relating to disasters caused by gas explosion points strongly to divergence from safe mining practice as the main cause. There is a need for greater training and education of personnel, closer analysis of gas reports, better monitoring and testing procedures, improved ventilation standards and a policy where safe working practice is actively encouraged. Conditions in the New South Wales occurrences of gas explosion were similar to those at Collinsville, Queensland in that dykes, igneous sills, burnt out coal and faulting were common to all. Information on outbursts indicates that contributing factors were intrusions, depth of cover, fault zones and other geological disturbances, methods of work, pressure and type of gas.

Jan 1, 1982

By P Duplancic and C R Lilley, R Hudson, D Beck

For deep block and panel caving mines, undercut or extraction level instability can have as much impact on overall recovery as underbreak or the premature ingress of waste. If the area of the mine affected by excessive convergence is small, recovery is usually possible. However, there are several examples of entire blocks that were abandoned prematurely due to footprint collapse. Clearly, such global instability has a major impact on recovery and must be avoided – this is one of the essential tasks for the design team.The design problem is complex. The planning engineer must ensure that the footprint has sufficient capacity to withstand the maturing loads in the cave, accounting for the effects of stress path, geological structures and the rock mass conditions. These are often uncertain and only sometimes quantified.The demand on the footprint will also be influenced by decisions and actions taken during production, especially related to draw, which can worsen a developing problem. Perhaps most importantly, the design decisions that favour stability and lead to lower deformation also negatively impact on idealised cave flow. Many engineers aim to minimise the size of extraction level pillars, to improve theoretical future resource recovery but in fact this can reduce recovery if widespread deformation ensues due to the undersized pillars.In 2014, PT Freeport Indonesia undertook detailed numerical analysis to quantify the effects of variability in rock mass conditions and geological structure on overall footprint performance. The analysis accounted for a range of stress paths and maturing cave loading scenarios sourced from a calibrated whole-of-cave deformation-flow model. The intent was to replicate some of the diversity and distribution of pillar deformation outcomes that may be seen in practice at Freeport.The discontinuum finite element analysis was able to replicate damage localisation around persistent structures, a realistic distribution of drive deformation and show how small areas of instability can evolve into major problems if poorly managed. The limits of pillar size and ground support as solutions to a number of different instability problems was also investigated, showing that pillar size alone was not a sufficient remedy for all adverse circumstances.In this paper, we describe the workflow for numerical analysis of footprint deformation. We discuss the compromises and considerations for balancing the sometimes competing needs for efficient extraction levels pillars, ground support and prudent draw strategy.CITATION:Beck, D, Hudson, R, Wilson, A D, Duplancic, P and Lilley, C R, 2016. An investigation of factors affecting the long-term reliability of extraction level pillars in deep block and panel caves, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 295–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Hugo T. Dummett

I would like to share some observations about the mining business and place the ongoing discussion in the context of our changed world. The mining industry practices its trade in a universe defined by prices, laws and governments. Prices, as in what the industry is paid for what it produces, and the costs of goods and services. Laws that have to be transparent and fair. And governments that the industry prefers to be stable and supportive of the industry, and certainly not corrupt. However, the day-to-day realities of the mining business in 2000 are not what they were 10 years ago. Several events have occurred that have resulted in a less populated workplace that is obliged to work much smarter and faster. These include real declining prices for most mineral commodities; low and diminishing returns to company shareholders; massive restructuring of the industry through mergers, partnerships and alliances; gold’s changed role from reserve currency to just another commodity; the growing importance of native title and the startling imperatives of “sustainable development.” In addition, the “borderless world” now means that resource companies will need to pass the test of being responsible corporate guests who respect and enhance the social, moral and societal values of their host countries.

Jan 1, 2000

By Schlanger H. P

A theoretical model for gas outbursts in underground coal mines is as follows. An outburst is the structural failure ofcoal due to excess stress resulting from body forces caused by gas pressure gradients. These body forces influence the stability of a mine face in the same manner that gravitational body forces affect the stability of the roof of a mine. The magnitude ofthese body forces can be appreciated when it is realized that for an average density coal, the gravitational body force is equal in magnitude to the force from a gas flow with a pressure gradient of 14 kPa m-I. Gas pressure gradients and the resultant stresses within a seam can be calculated with numerical methods. Thus, providing the necessary parameters can be measured or estimated, in principle the theory can be applied to compare the outburst risk of various mining arrangements.

Jan 1, 1985