Search Documents

By Graeme Heyes, Warren J. Bruckard, Michael A. Somerville

"Over the past few years CSIRO Minerals has been conducting research aimed at developing a continuous copper converting process to replace the traditional two-stage batch process that is currently used to produce blister copper. Sirosmelt type reactors and calcium-ferrite (lime-based) slags have been used rather than the conventional iron silicate slags. The research work has now been extended to focus on the development of a single-stage continuous copper making process (so-called direct copper converting) in which copper concentrates are converted to low-sulfur blister copper in a single step, that is the smelting and converting steps occur in one continuous stage.One feature of the direct copper converting process is that copper losses to the slag phase can be high, meaning the slag produced needs to be treated to recover the copper value. The feasibility of the whole copper making process will most likely depend on the efficiency and cost effectiveness of the copper recovery stage. Flotation has been identified as the most economical option to recover the copper from direct copper converting slags where it has been estimated that a copper recovery from the slag of above 90% is required to make the overall single stage copper making process economically feasible.A limited series of laboratory batch flotation tests was conducted on a suite of calcium-ferrite-based slags made in laboratory smelting trials. Copper sulfide concentrates from MIM were used as feed-stocks. The objectives of this work were to develop a robust flotation process to maximise the copper recovery and iron rejection from slags made in the process, and to establish operating conditions for future continuous flotation pilot plant trials.The slags treated included a reduced low copper slag, an oxidised high copper slag composite, and a very reduced low copper self-pulverising slag. The copper content of the slags varied from 2.9% to 14% Cu and the CaO/Fe ratio varied between 0.30 and 0.54. In general, the higher the copper content the more oxidised the slag. The copper was present as metallic copper, oxide copper and copper-calcium ferrite phases with the phase mix related to smelting conditions. The slags were crushed, ground, wet-screened at 355 or 210 µm to remove coarse metallic particles of copper, and floated at natural pH (about pH 11) using reagents and conditions appropriate for the selective recovery of the copper phases. Reagent additions were typically 200 g/t KEX and 500 g/t Na2S.9H2O and the grind size was generally a P80 of about 40 µm."

Jan 1, 2003

By Gui-fang ZHANG, Zhe SHI, Lei GAO

Secondary V-recycling slag, an industrial waste containing high gallium is being dumped continuously, which causes the loss of gallium. Thus, the alkali fusion process was employed to recover gallium from this slag. The effects factors on extraction of gallium such as roasting temperature, roasting time, alkali fusion agent concentration and CaO concentration were investigated in the paper. The experimental results indicated that excessive roasting temperature and roasting time is unfavorable to the recovery rate of gallium. The appropriate roasting temperature and duration are 1000 and 2 hours, respectively; The appropriate proportioning of Na2CO3: NaOH is 2:1 when the concentration of alkali fusion agent weighs 0.4 times the mass of the slag; In order to remove SiO2 from the leaching liquor, CaO should be used as an additive in the roasting process. The appropriate concentration of CaO should weigh 0.2 times the mass of the slag. Employing these optimal alkali fusion conditions in the roasting process, gallium recovery is above 90%

Jan 1, 2015

By Georgy A. Cherkashov, Andrey V. Efimov, Yury S. Borodaev, Nadezhda N. Mozgova, Sergey G. Krasnov, Tamara V. Stepanova, Alexander M. Ashadze

"Abstract - A horizontal mineralogical-geochemical ore zonation with a southeast to northwest trending succession of Cu and Fe (Zn) main zones has been discovered in the Logatchev hydrothermal field (14°45??N Mid-Atlantic Ridge). The major minerals are pyrite, chalcopyrite, bornite, isocubanite, digenite and chalcocite. Zn-sulfide, marcasite and covellite are less abundant. Rare minerals are native copper, zincian copper and cobalt pentlandite (first found in oceanic massive sulfides), Cu and Cu-Co-bearing Fe-disulfides. Two groups of the main sulfide assemblages with different copper contents are recognized: Group I comprises assemblages with primary sulfides (isocubanite, chalcopyrite, pyrite and Zn-sulfide; Cu up to 35 wt% in Cu-bearing minerals); Group II contains assemblages with secondary Cu-rich sulfides (bornite, digenite, chalcocite; Cu ~60 wt%) as well as rare minerals (cobalt pentlandite, native copper and zincian copper). The assemblages of Group I formed at a temperature of about 300°C; the sulfur fugacity (log fs2 atm) at 300°C is probably 9.9. Relations between minerals of this group are contradictory, attributed to non-equilibrium environments, and no unified sequence of crystallization of minerals has been determined. Minerals of Group II replace, rim or cross the assemblages of Group I. Group II minerals crystallized in a distinct sequence (cobalt pentlandite-bornite-digenite- chalcocite-native copper), with increasing copper content from the start to the end of the depositional sequence. This may correspond to pH from 7 to 8 near Eh = -0.2 at 250°C. Minerals of this group were generally formed under hypergene alteration processes. Compositions of ore minerals were studied by means of electron microprobe analysis (EMPA) (150 analyses). Narrow composition fields were revealed in all main sulfides, which comprised known experimental data. ZnS contains 6.0 to 28.0 mol.% FeS, which is close to data known for other hydrothermal massive sulfides from the Mid-Atlantic Ridge (MAR). A common admixture in ZnS is Cu (0.16 to 1.32 wt%). Rare grains of unusual anisotropic Fe-disulfides, (Fe0.95Cu0.05)S2 and Cu(Fe,Co)9S20, were found among the ore minerals."

Jan 1, 1999

By James P. Ludwig

While we are all aware of the need for reclamation of mine sites, few managers and engineers seem to be aware that good reclamation begins with the earliest plans for mining and processing of ores. Far too often the attitude that reclamation is an add-on to worry about at the end of the mining process dominates the thinking of mine engineers and management, A common result is that the reclamationist can be faced with mining and waste disposal designs that are nearly impossible to deal with effectively from an ecological perspective. Everyone of us has been victimized by the down time and maintainence cost that resulted from the purchase of an outwardly attractive, but poorly designed piece of equipment. When confronted by design defects in equipment, a distraught owner can always trade it in, call a consumer advocate, or follow up one of the "lemon laws" at either the federal or state level. A poorly designed mine for reclamation purposes usually cannot be treated either with ease or cost effectiveness. Good reclamation can be effectively prevented by the designs used when the mine was planned. The purpose of this paper is to share some of the experiences our firm has had with reclamation projects at mines in the Upper Midwest as these were influenced or controlled by mine design decisions. My aim is to sensitize mine planners and managers to planning processes they should consider, and hopefully use, early in the mining process to assure successful reclamation during and after mining. Many of the examples I will cite are from experience gained at the recently closed Jackson County Iron Company taconite operation at Black River Falls, Wisconsin. I am particularly grateful to Mr. Vern Metzger, mine manager at JCIC, for his unflagging support of good reclamation practices, employee training programs (which have included reclamation techniques), and his forebearance to put up with our group of ecologists. I realize that this was a time when there were significant internal and external pressures to cut all costs including reclamation efforts. The collaboration has been successful as you will soon see.

Jan 1, 1984

By S. Hicks

This technical note describes an alternative procedure that can be used in linear programming calcula¬tions where the compliance limit of lbs S02/million Btu for the blending coal is subject to change. Dr. Mateer in his technical note titled "Coal blending for sulfur compliance" (ME, September 1994, p. 1103) defined an "excess sulfur" parameter that provides a valid constraint equation for a linear program optimization. The coals used by Dr. Mateer in his examples are shown in Table 1. To create the parameters for the constraint equa¬tions to blend to an SO2 content of 1.2 lbs S02/million Btu; the excess sulfur for Coal A was defined as Sulfur excess%o = 0.5 - 0.6-13,000/10,000 = -0.28 This equation was used to create the constraint equation -0.28A + 0.44B + 1.36C<- 0.0 Another way to create the parameters for the constraint equation is given below. In these equations: ? W is the total weight; ? A, B and C are the fractional proportions of each potential blend stocks; ? Sa, Sb and Sc represent the percent sulfur content of the blend stocks; ? Ha, Hb and He represent the calorific content of the blend stocks in Btu/lb; and ? H and S represent calorific and sulfur contents of the composite blend. The weight of blend to produce one million Btu is [ ]

Jan 1, 1997

By J D. Pease, J M. I Tuppurainen, P D. Munro

This paper examines how legislation and regulation can be external drivers of technical change in mineral processing and extractive metallurgy and how the industry can respond. Two examples are considered; the production of copper metal from concentrates and the cyanide process for gold production.The Clean Air Act (1970) in the USA initiated a wave of attempted innovations in the extractive metallurgy of processing copper sulfide concentrates to meet forthcoming standards on sulfur dioxide emissions. Interestingly, a satisfactory technical solution existed (flash smelting and gas capture) but had not been widely adopted.Nearly fifty years later the primary copper industry finds itself with new challenges. One major challenge is how to deal with the increasing level of arsenic in copper concentrates. Most countries impose an upper limit on arsenic in imported concentrate; typically, 0.5% As or less. Higher arsenic concentrates can be blended with cleaner ones to meet the limit, but this tactic cannot be used indefinitely as the average arsenic level of global concentrates rises inexorably. Further, smelters (often in urban locations) cannot be expected to deal with both ever-increasing arsenic in the feed and stricter restrictions on emissions and disposal. A rising “inventory” of primary copper deposits are already constrained from development by high arsenic concentrate. These deposits will need to be developed if future copper demand is to be met. An economic and technical solution to arsenic is needed. The gold industry may also face challenges in the use of cyanide, by far the dominant lixiviant used in gold and silver production. Public perception has driven restrictions on the use or transport of cyanide in some jurisdictions. History suggests that such pressure is only likely to increase. While there are several alternative lixiviants, none can yet match the utility and economics of cyanide.Such important issues will not be resolved by incremental change or new equipment items. They require development of new process technology - a tectonic event rather than an incremental change. It requires sustained effort (and expenditure) over decades and is very unlikely to result from “business as usual” for producers, suppliers or academics. Past major process developments were driven by a dire need for economic survival or by legislative change. What will drive the future changes?CITATION:Munro, P D, Pease, J D and Tuppurainen, J M I, 2017. Technology change by regulation – a cresting wave?, in Proceedings MetPlant 2017, pp 45–58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

To the Members It has been, and is the endeavor of the A. I. M. E. to serve each and every member. One of the means of letting the membership know what is going on in the mining; metallurgical and chemical fields, and by far the most important, has been our monthly Bulletin. To publish this costs money, and to partly defray the costs, it was decided to accept such advertising as could be secured. The A. I. M. E. is the only one of the American National engineering societies whose dues are as low as $10 per year, and it actually spends more upon the Bulletin and Transactions than the sun total it receives for clues. Hence the need of advertising revenues. We are planning even greater improvements for your Bulletin-improvements that will help you in your work. It will mean a better publication, with more information than ever before. To successfully carry out our plans, we must have your co-operation. We are not asking you for financial, but for your moral support. With that we shall accomplish a great deal. What we ask of you, brother member, is to give evidence to those patronizing our advertising pages, that you not only read the editorial pages, but the advertising section as well, and that you have in mind the welfare of your Institute by consulting the advertising pages when in the market for equipment. Do you realize that if you mention your Bulletin when writing advertisers or purchasing supplies, that not only would your publication secure more advertising, but better satisfy present advertisers. We have reason to know that our advertisers secure business as a result of our publication, but they demand some evidence that you see their advertisement. Unfortunately, our members do not as a rule mention where they saw the advertisement, and as a consequence advertisers have no means of knowing whether their investment in the Bulletin is paying. The A. I. M. E. Bulletin can be made the best advertising medium in the mining, metallurgical and chemical fields, simply by each member doing his bit. It is very little to ask of you, and the returns to the mining industry will be enormous.

Jan 9, 1915

By James R. Fahy, Lawrence A. Hansen, J. David Deatherage

A laboratory testing program was con- ducted to investigate the shear strength along specific soil-liner interfaces for five types of liners of varying thicknesses. Results indicated a bilinear relationship between shear stress and applied normal stresses ranging from 276 to 1000 pKa (40 to 145 psi). Friction angles along the soil- liner interface below the break point normal stress (7.5 to 19 degrees) were lower than those recorded above the break point normal stress (14.5 to 39 degrees ).

Jan 1, 1987

By C. H. Herty

The reactions that occur in the basic open-hearth process are complicated and are subject to many different factors such as temperature, slag composition and rate of boiling of the bath. It is difficult, therefore, to present an extended theoretical discussion of open-hearth operations without confusing the theory of the process with the application of the theory. This paper attempts to present some of the theory of the open-hearth process without mentioning theory at any point, simply giving some of the practical applications of results founded both on theory and practice and on experimental work both in small and large furnaces. It is hoped that an answer to a number of questions commonly asked by the open-hearth operator may be found in this paper. Discussion of the subject matter is taken up more or less in the order in which a heat ie worked, beginning with the oxidation of the scrap charged, sulfur absorption by the scrap, calcination of the limestone, and extending into the pig iron for the charge, the slags formed during the process, and some of the phenomena occurring in deoxidation of the steel and in its action in the molds. Oxidation of Scbap When scrap is charged into a furnace it immediately begins to oxidize, Oxidation is carried out by.three reactions: Fe + H20 + FeO + Hz (absorbs heat) (1) Fe + C02 + FeO + CO (absorbs heat) (2: Fe+ ½O2 + FeO (gives off heat) (3: The product of oxidation contains some Fe3O4, but FeO usually predominates on account of the iron present in close contact with the scale formed For a given type of scrap the amount of oxidation is controlled by thc fuel and by the excess air being carried in the furnace, the temperature 01 the furnace, and the length of time that the scrap is in contact with the furnace gases. In general, less oxidation occurs when the furnace is rur hot so that the scrap melts rapidly. More important in operation thar the two variables atmosphere and temperature, is the type of scrap being

Jan 1, 1929

By George H. Holmes

The water situation in Nevada mineral and related industries is described in this report. It contains information on the sources and adequacy of supply to current operators, requirements and uses, quality and costs, geography, hydrography, precipitation and evaporation characteristics, and Nevada water laws. Also, information is given on the water requirements of one public utility powerplant, and the source and consumption of water in four major cities. Water distribution at 24 operations is shown on schematic waterflow diagrams. The mineral industries of Nevada in 1962 used 8.6 billion gallons of new&apos; water and reused 3.8 billion gallons for a total usage of 12.4 billion gallons. The copper industry was the major water user. The 1962 value of all mineral production in Nevada was $85.5 million. The large amount of water required to maintain thin high production is obtained principally from ground-water sources in alluvial valleys and the permeable rock formations of some mountain ranges. Some water is also obtained from perennial streams and springs. Sources of water utilized by existing industry ire near most mineral industry operations; however, seven companies are forced to pipe water distances ranging from 2 to 8 miles. Although water supplies of presently operating companies are adequate at most operations, several companies resort to large-scale reuse of water as a matter of conservation and economics. Acquisition of water by new operators is possible but takes considerable negotiation. Water rights, surface and underground, are controlled by the State. The quality of the water is satisfactory for most purposes. Analyses of 19 samples, listed in the appendix, show the range in water quality at various plants throughout the State. Costs of delivering new water to current operations range from 2 to 26 cents per 1,000 gallons with an average of 10 cents per 1,000 gallons for power and maintenance. No firm costs for recirculating water were available; estimated costs range from 1.5 to 2.5 cents per 1,000 gallons. The mineral-product value of the entire Nevada mineral industry in 1962 was equivalent to $10 per 1,000 gallons of new water and $26 per 1,000 gallons consumed. Projection of the 1962 water requirements of the Nevada mineral industry indicates that the demand For new water will increase from 8.6 billion gallons in 1962 to 11.9 billion gallons in 1980, a 43-percent increase. Water requirements in the year 2000 are estimated as 14.8 billion gallons, an increase over 1962 water demand of 78-percent.

Jan 1, 1966

By George H. Holmes

The water situation in Nevada mineral and related industries is described in this report. It contains information on the sources and adequacy of supply to current operators, requirements and uses, quality and costs, geography, hydrography, precipitation and evaporation characteristics, and Nevada water laws. Also, information is given on the water requirements of one public utility powerplant, and the source and consumption of water in four major cities. Water distribution at 24 operations is shown on schematic waterflow diagrams. The mineral industries of Nevada in 1962 used 8.6 billion gallons of nee&apos; water and reused 3.8 billion gallons for a total usage of 12.4 billion gal¬lons. The copper industry was the major water user. The 1962 value of all mineral production in Nevada was $85.5 million. The large amount of water required to maintain this high production is obtained principally from ground-water sources in alluvial valleys and the permeable rock formations of some mountain ranges. Some water is also obtained from perennial streams and springs. Sources of water utilized by existing industry ore near most mineral industry operations; however, seven companies are forced to pipe water distances ranging from 2 to 8 miles. Although water supplies of presently operating companies are adequate at most operations, several companies resort to large-scale reuse of water as a matter of conservation and economics. Acquisition of water by new operators is possible but takes considerable negotiation. Water rights, surface and underground, are controlled by the State. The quality of the water is satisfactory for most purposes. Analyses of 19 samples, listed in the appendix, show the range in water quality at various plants throughout the State. Costs of delivering new water to current operations range from 2 to 26 cents per 1,000 gallons with an average of 10 cents per 1,000 gallons for power and maintenance. No firm costs for recirculating water were available; estimated costs range from 1.5 to 2.5 cents per 1,000 gallons. The mineral-product value of the entire Nevada mineral industry in 1962 was equivalent to $10 per 1,000 gallons of new water and $26 per 1,000 gallons consumed. Projection of the 1962 water requirements of the Nevada mineral industry indicates that the demand for new water will increase from 8.6 billion gallons in 1962 to 11.9 billion gallons in 1980, a 43-percent increase. Water requirements ill the year 2000 are estimated as 14.8 billion gallons, an increase over 1962 water demand of 78-percent.

Jan 1, 1966

By J. P. Harrison, K. Gao

It is well known that in situ stress measurements at a given site will generally display significant variability. However, it appears that a robust analysis of such measurements – i.e., one that is faithful to the tensorial nature of the data – is not available. Despite the fact that stress is a tensor, stress magnitude and orientation have long been analyzed separately using classical statistics. In earlier work we demonstrated the applicability of tensor statistics to the analysis of stress variability. Here, we investigate further the difference between tensor and classical statistics with respect to the stress tensor correlation matrix. Our analysis commences with the selection of a series of valid correlation matrices. Then, assuming that standardized tensor components follow the multivariate standard normal distribution, these correlation matrices are used to generate marginal probability distributions of the eigen-parameters (i.e., principal stress magnitude and rotation angle). From these, random stress tensors are generated, their eigenparameters determined, and the probability density distributions of these obtained using both classical and tensor statistics. Our results indicate that, for all correlation matrices, both methods give practically identical distributions for principal stress magnitude. However, the discrepancy between the two methods with regard to probability density distribution of rotation angle is highly dependent on stress component correlation. This discrepancy is usefully quantified in terms of the integral, with respect to orientation, of the difference between the two probability density distributions. This parameter, which we term Area Difference, is closely linked to the magnitude of the correlation matrix determinant, which itself is related to the normal stress correlation coefficient (i.e., ?x ,?y ??). Assuming that Area Difference should not exceed 0.1, we identify the critical determinant for any particular value of normal stress component correlation coefficient. Thus, using published in situ stress data and the obtained critical determinants, we show that for a specific normal stress component coefficient, when the correlation matrix determinant is less than its critical determinant, the more precise tensor statistics should be used to calculate the distribution of rotation angle. These results demonstrate that the customary analysis of stress measurement data may lead to erroneous results, and that tensor statistics appears to be preferred approach.

Jan 1, 2015

A Discussion at a meeting of the New York Section, Dec. 2, 1914 D. H. BROWNE.-If 35 years ago we had met to discuss the subject that is before us to-night, the criticism that we must all be mad or we would not be here at all would have been perfectly applicable. No group of men would have come together a generation ago to discuss the subject of smelting ores without extraneous fuel, or largely by the oxidation of their own impurities, without incurring the imputation of being crazy. But metallurgy, like all other branches of human industry, progresses by idealism. In every generation there are old men who see visions and young men who dream dreams. Thirty-five years ago John Hollway conceived the idea that in the Rio Tinto ore the sulphur and iron, if properly oxidized, could be made to produce heat enough to carry on the smelting of the ores. He saw the vision. Twenty-five years ago Mr. Austin, of Montana, took out a patent on a furnace in which to carry out Hollway&apos;s ideas. He dreamed the dream. Twenty years ago a man working in Montana grasped the possibilities of this idea. To him has been given that inexpressible pleasure which comes from realizing the idea and making the concept concrete. Gentlemen, it gives me great pleasure to introduce to you the man who made the ideal real, Robert Sticht, of Tasmania. ROBERT C. STICHT, Queenstown, Tasmania.-I find it extremely difficult to act up, in the smallest degree, to the enconium passed upon me by Mr. Browne. It is true it has been my good fortune to be able to put some sort of method into the "madness" of 25 years ago; but I am not the originator of the idea, nor the only one who has carried it out. Mr. Browne mentioned the originator, who undoubtedly is Mr. Hollway. He also mentioned Mr. Austin, who gave the first instigation to pyrite smelting as now practiced. As against both of these men I was fortunate enough to be able to command the necessary natural resources to carry out the idea continuously in a practical way, so as to make it permanently possible.

Jan 4, 1915

By S. Onuki, T. Ando, M. Tejima, R. Enomoto, Y. Okada

"Al–Si–Cu–Mg die casting alloys are widely used in the automotive industry, and recent advancements in high pressure die casting technology enable heat treating products to achieve desirable properties. However, CO2emissions associated with die-casting production lines should be reduced to address the global warming issue. In this study, the relation between the microstructures and thermal stability of precipitates formed during isothermal aging at 423, 485, and 558 K of Al-11.0 mass%Si-1.8 mass%Cu-0.2 mass% Mg (JIS ADC12) was investigated using Vickers hardness tests and transmission electron microscopy (TEM). The hardness tests and TEM results showed that Si compounds and Al–Cu compounds enhanced the mechanical properties of the alloy and that the predominant compound affecting the mechanical properties differed between specimens treated at 423 K and those treated at 558 K. Moreover, additional aging at 423–458 K resulted in a material with a Vickers hardness higher than that of the isothermally single-aged material. Differential scanning calorimetry, differential elemental analysis, and selected-area diffraction analysis using TEM suggested that the combination of Al–Cu compounds precipitated at low aging temperatures and Si compounds precipitated during preliminary aging increased the mechanical strength, resulting in a maximum hardness of 130 HV.INTRODUCTIONAl–Si–Cu–Mg die casting alloys have well-balanced mechanical properties, machinability, and cast ability. These alloys are therefore widely used in the automotive industry because of their superior characteristics, accounting for>90% of the aluminum used in die casting production. As a substitute for iron-based materials, these alloys have contributed to the development of lightweight vehicles.Dong et al. (2014) reported that the heat treatment of die casting materials is effective for changing their dimensions under high temperatures as a result of the precipitation of solid-solution elements. Recent advancements in high pressure die casting technology have led to the application of heat treatments of Al–Si–Cu–Mg alloy products to reduce fuel consumption and satisfy customer needs. Although attempts to reduce CO2emissions have focused on fuel consumption in cars and fuel efficiency regulations have become increasingly strict in recent years, CO2discharged from production lines should also be reduced without adversely affecting the properties of the product. Heat treatments for artificial aging after solution treatment (T6 treatment) and after casting (T5 treatment) are CO2discharge sources, which together with a holding furnace account for >80 % of the CO2discharged during the casting process."

Jan 1, 2018

By J. M. Floyd

"Top submerged lance furnace developments started in CSIRO in the early 1970s and was given the name Sirosmelt. In the early work the technology was developed for tin smelting and processing tin slags but once a small pilot plant was established other slag processing applications were soon recognised and evaluated for various copper, nickel, zinc and cobalt-containing slags. The process was tried for copper smelting and converting, which was proven in the small pilot plant in 1978. In the same year the first commercial application of the technology was established for the recovery of tin from slags at Associated Tin Smelters, Sydney. Work on lead smelting was initiated by the CSIRO team in the late 1970s and laboratory work led to pilot plant trials by Mount Isa Mines.In the second decade of the technology the focus of development became commercial acceptance of the technology through marketing, development and application by Ausmelt and Mount Isa Mines; the former commercialising and developing the technology for a wide range of applications, while the latter concentrated on its own commercial needs of copper and lead smelting. This decade saw a number of commercial plants built in Australia, with considerable interest becoming evident from other parts of the world. Towards the end of this decade Mount Isa also entered into the business of marketing of the technology through rights dating to the joint work with CSIRO in the late 1970s.So far, after five years, the third decade of the technology has been characterised by diversification of applications of the technology to areas outside the non-ferrous and precious metals production industry. The waste processing and recycle industry and the iron and steel industry have recognised that the top submerged lancing system is a new type of reactor with many significant features which provide new opportunities for processing a range of materials under good environmental controls in a cost effective manner.I hope this audience will excuse my boldness in talking about the third decade of the technology when we are only half way through! I am aiming in this paper to not only talk about the past, but to try illustrate the future directions which I envision."

Jan 1, 1996

By Yang Xiao, Zhang Yimin, Bao Shenxu, Liu Chun

Stone coal is a unique vanadium-bearing resource in China. Many techniques, such as salt roasting-water leaching, blank roasting-acid leaching, direct acid leaching etc. have been developed for vanadium extraction from stone coal. The vanadium leaching rate can reach 74.9% for stone coal from Jiangxi, but only about 27% of vanadium is leached for Hubei ore by applying salt roasting-water leaching technique. This paper investigats the vanadium occurrence in stone coal by microscope observation and electron probe, and compares the minerals components of stone coal from Jiangxi and Hubei. Although most vanadium exist as an isomorphism by replacing Al(III) from dioctahedral structure in mica group minerals in stone coal from two regions, the free vanadium is remarkably abundant in Jiangxi stone coal than in Hubei stone coal, which results the fact that vandium is relatively readily extracted from former. Moreover, the content of calcite in Hubei stone coal is much higher than that in Jiangxi stone coal. Calcium can react with V2O5 to form water insoluble calcium vanadates during roasting and this may be the reasone why the water leaching rate of vanadium is low for Hubei ore. Acid leaching is more beneficial to the vanadium leaching but other extra methods, such as adding aid-leaching agent and/or increasing acid concentration is need for the ore where vanadium is embeded firmly. This study can effectively guide the selection of vanadium extraction techniques for stone coal from different regions.

Jan 1, 2014

By Robert Kimutis, Ke Yang, Yi Luo, Jianwei Cheng

"Surface subsidence processes, especially those associated with a longwall mining operations, could cause operational and/or safety problems to railroads. For railroads with normal amounts of traffic, both the limited time window between traffic and the limited space available make the efforts to return the railroad back to its original state nearly impossible. In order to ensure the safe operation of a subsiding railway, the partial lifting method has been developed and applied. This paper describes the principle and application of the method. A case of applying this method to mitigate subsidence effects on a long section of railway has been demonstrated.INTRODUCTIONMaintaining an operational railway as it is experiencing a longwall subsidence process is not an easy task. The subsidence process may induce sufficient strain and curvature to cause problems to the railroad structures. Localized subsidence-induced slope often is significantly larger than the permissible ruling gradient of 0.7% for a locomotive to haul a loaded train reliably. In order to ensure safe operation, it would be ideal to instantly lift the railroad track back to its original level as it is subsiding. However, it is often impractical to do so due to the limited time windows available between railway traffic and the available space on the railroad base.A partial lifting method has been developed to keep the railroad operational under such limitations. The subsiding railroad track is raised by only a determined, partial amount of the occurred subsidence at a given time. By making such a determined adjustment, the railroad track can be maintained on a smooth and operational profile, and the high strain and curvature on the railroad structures can be reduced as well. To define a smooth railroad track profile in a subsided section the following two conditions should be met: (1) the maximum railroad gradient should be less than the permissible ruling gradient, and (2) the recommended amount of adjustment should be able to be made by the repair crew within the available time windows between scheduled railway traffic.The subsidence effects on a long section of railroad over two longwall panels have been successfully mitigated using the partial lifting method. The railroad experienced a maximum subsidence 89 of about 5 .0 ft (1.5 m) with the average subsidence along the entire length being about 3.45 ft (1.05 m). However, the average adjustment due to lifting that was made along the entire length of the subsidence-influenced railway was only 0.5 ft (152 mm)."

Jan 1, 2010

By R. B. Adamson

The fatigue behauior of irradiated copper single crystals is compared to that of unirradiated crystals. Proton or electron irradiation did not substantially change the fatigue-lzj.e, fatigue-hardening-, or slip-line characteristics, while neutron irradiation did appear to alter these parameters. Postfatigue transrrzission electron microscopy did not reveal any marked structural differazces between irradiated and unirradiated specimens. Possible dislocatio~a mechanisnzs to explain the observed behavior are discussed. A LTHOUGH considerable work has been done to ascertain the effects of radiation on the tensile properties of metals (e.g., Refs. 1 and 2), little work of a basic nature has been reported on the effect of radiation on fatigue properties. Since it is known that fatigue properties are sensitive to conditions at the surface of the metal, it was felt that charged particle irradiation, whose penetration into metals is very small, might influence the fatigue behavior. To investigate this surface effect, irradiations with 10 mev protons and 1.5 mev electrons were conducted. The range of 10 mev protons in copper is about 0.236 mm; which is very small compared with the thickness of the specimens used (1.53 mm). The range of 1.5 mev electrons is somewhat larger, on the order of 0.665 mm.4 On the other hand, irradiation with reactor neutrons produces damage throughout the entire specimen, so neutron irradiation can be used to study the effects of bulk damage. The damage introduced by proton and neutron irradiation is expected to con!ist of large interstitial dislocation loops,5 tiny (<25A) vacancy loops," and/or various vacancy-rich regions called depleted zones.&apos; In the case of electron irradiation at about -173°C the damage is expected to consist of isolated Frenkel pairs.&apos; The effect of radiation damage on the fatigue properties of some engineering materials has been reported,g,10 but the results are not clear-cut or consistent. SPECIMEN PREPARATION Zone-refined copper was used to grow single crystals by a modified Bridgeman technique in an inert helium atmosphere. Using a seeding method, single crystals were obtained as bars about 6 in. long with a cross section of 3 by $ in. Immediately upon removal from the split-mold graphite boat in which they were grown, the very soft bars were embedded in a room-temperature setting plastic. They could then be cut into specimen lengths without introducing any long-range damage. Generally, four or five specimens plus one seed were obtained from each bar. The plastic material was dissolved away in acetone and the orientation of each sample was checked by the standard Laue X-ray

Jan 1, 1968

By T. PH. D. Egleston

THE origin of gold both in placer deposits and in veins, and especially the origin of nuggets, has been the subject of repeated discussions and investigations, which have been recently brought to my attention by several extremely interesting specimens sent to me for examination, and more especially by the one exhibited at the meeting of the Institute in February, 1880.* In the year 1874 I made some examinations of the hydraulic mines of Califor¬nia, and was very much struck with the distribution of the gold throughout these deep placers, which were almost invariably poor on&apos; the surface, while gradually growing richer towards" the bed¬rock. The constant presence of fossil wood, and the large quantity of organic matter contained even low down in these beds, was also remarkable. Not being satisfied with the various theories advanced to account for the formation of these deposits, I began an investiga¬tion early in the year 1879 on the conditions of solubility of gold and the causes of the loss in working gold ore in a large way: The researches which I have undertaken show that gold must be considered a soluble rather than an insoluble metal, and that the conditions of solution are such as will be found anywhere where gold is likely to occur, and the solution may take place even under the ordinary cir¬cumstances of surface drainage, and may be going on freely even where the presence of gold has never been suspected, and that there are causes enough in nature to produce the solution of the gold in sufficient quantities to account for all the phenomena of both the vein and placer formations. The general theory with regard to the formation of these placer deposits and nuggets has been that they were the result of the de¬struction of pre-existing- vein-matter, which does not accord with the facts as shown in the deep placer deposits. The gold in such case would be distributed in layers of unequal richness throughout * Transactions of the American Institute of Mining Engineers, vol. 8, p. 451.

Jan 1, 1881

By D. E. Peacock, B. Harris

The mechanical behavior of a niobium (columbium)TUNG alloy containing 20 wt pet Ta. 15 wt pet W, and 5 wt pct Mo has been studied in the temperature range 77° to 423°K. All specitrzens tested, apart from those into which oxygen was introduced deliberately, were fully recrystallized at 1500°C, had an average grain diameter of approximately 0.03 mm, and a combined carbon, ox-vgen. nitrogen, and hydrogen content of not not more than 250 ppm The meckatnical behavior of this alloy was found to be similar in seine respects to that of unalloyed bcc transilion metals. Both yield and flow stresses were sensililae to changes in deformation rate and both increased rapidly as the temperature was lowered below 150°C. A detailed examination revealed, however, that most of the temperature dependencc of the yield stress could be accounted for by the temperature dependence of the elaslic, modulus, whish is not true of the unualloyed metals. In lension at moderate strain rates, the trunsition fvom ducfile to hvittle behavior occurred just belour room teunperature bur incveasing the oxygen content from 190 to 200 pptn raised the transition temperature to about 4000K. TUNGSTEN and molybdenum have been found to be very effective high-temperature solid-solution strengtheners of niobium, but the amounts of these elements that can be added are limited if the alloy is to retain useful room-temperature ductility. It has been shown, however, that partial replacement of niobium with tantalum lowers the ductile-to-brittle transition temperature of such alloys and allows larger additions of molybdenum and tungsten to be made. Some of the high-temperature properties of niobium alloys containing these elements have been reported by Bartlett et al.,&apos; and the work presented here describes the low-temperature behavior of one of these, a solid-solution alloy containing, by weight, 20 pct Ta, 15 pct W, and 5 pct Mo. The elastic modulus, the temperature and strain-rate dependence of the yield and ultimate tensile stresses, and strain-hardening effects are discussed and compared with those of unalloyed niobium. EXPERIMENTAL MATERIAL AND PROCEDURE The material used in this investigation was produced from a 6-in.-diameter, double arc-melted ingot. This was can-extruded at about 1150°C to a 3-in.-diameter billet, and after annealing for 1 hr at 1345°C the billet was heated to 1315OC and part rolled and part forged to 0.5-in.-thick plate. The resulting material exhibited a cold-worked structure

Jan 1, 1965