Search Documents

By Walter S. Weeks

THE subject of the flow of air through a mine under the influence of natural ventilation has proved an elusive one. To my knowledge only cut and try algebraic solutions have been used where multiple paths are involved. The object of this paper is to present a method for the graphical determination of the flow induced by the natural ventilation pressure (N.V.P.) alone or in combination with a fan. The N.V.P., measured in pounds per square foot, induced by two columns of air between two horizontal planes at different elevations, is equal to the difference in weight of the two columns, assuming each to have a cross-sectional area of 1 sq. ft. Pressure in pounds per square foot is converted into inches of water by dividing by 5.19. Methods of calculating the N.V.P. have been discussed in the literature. In this paper, for simplification of exposition, the change in pressure due to the weight of superimposed air will be assumed directly proportional to the length of the column. The actual methods of calculating the N.V.P. do not affect the solutions to be presented. It must be realized that the precision to be obtained from the small- scale, inked diagrams presented is not as great as would be obtained from large-scale, penciled curves that would be used in practice. The accuracy of the curves does not warrant reading "volumes" closer than the nearest thousand cubic feet per minute. CASE I. DUCTS IN SERIES The simplest type of problem is to determine the flow when two shafts are connected by a crosscut, as shown in Fig. 1. In this example, the resistance of the shafts is to be taken as 0.0001 in. of water for a flow of 1000 cu. ft. per minute for a length of 1000 ft. The resistance of a crosscut is to be taken as 0.0005 in. of water for a flow of 1000 cu. ft. per minute. The small pressures necessary to cause changes in velocity will not be considered, because the accuracy of other obtainable data does not warrant their consideration.

Jan 1, 1938

By Edward Pesout

THE McGill smelter started operations in the year 1907. The smelter furnaces were fired with run-of-mine coal on grates until April 1911, when oil firing was introduced. Oil firing continued until April 1918, when the initial coal-pulverizing plant was started.1 EARLY PULVERIZING PLANT Various alterations were made to that plant during its operation, one of the more important being in connection with the system for delivering pulverized coal. In order to minimize coal-dust explosions and fires, the return portion of the main delivery line was eliminated in the year 1928. Thereafter coal-dust explosions and fires were greatly reduced. Pulverized coal was prepared at this plant primarily for the reverberatory furnaces, but for several years it was also delivered to the converting plant, roasters and power-plant boilers by a system of auxiliary fans and delivery lines. During the period March 29 to April 8, 1929, one reverberatory furnace was fired with pulverized coal produced by an Aero, type J, unit coal pulverizer with a rated capacity of 5 tons per hour. This machine actually pulverized its rated capacity but the product was too coarse. After certain regulations, a finer product was obtained but the pulverizer capacity decreased and this resulted in insufficient coal for efficient furnace operation. Table I gives a comparison of the average screen analyses of the pulverized-coal products from the impact-type unit pulverizer and the regular coal-plant installation. [ ] It was definitely proved that this size and type of unit pulverizer could not furnish sufficient coal of proper fineness to give smelting results comparable to that obtained with the regular coal-pulverizing plant. The coal from this unit pulverizer was so coarse that it did not ignite or burn properly and thus did not produce the proper heat for efficient smelting. During the latter part of 1929 and the early part of 1930, experimental work was conducted with a 7-ft. 0-in. by 48-in. Hardinge conical ball-mill coal-grinding unit, which was installed alongside a furnace in the reverberatory building. Results obtained from the test run indicated that this unit would furnish sufficient coal of proper fineness for good smelting.

Jan 1, 1945

By O. D. Gaither

This paper is an analytical study of the flow of fluids through small vertical conduits. Small conduits are defined as 11/4-in. nominal diameter tubing size and smaller, and approximately twice this area for annular conduits (i.e., 1- X 21/2-in. annulus and smaller). Experimental data are presented for the 1-X2-in. and 11/4- X 2%-in. annuli, and the I-in. and 11/4-in. tubing, since these represent the small conduit sizes and configurations generally encountered in oilfield applications. Data have been gathered for these conduits for single-phase water, single-phase gas and two-phase water-gas mixtures, with particular emphasis on high gas-liquid ratios. Water rates in excess of 2,000 BID and gas rates in excess of 2.5 MMcf/D, and two-phase flow ratios in between these two, represent the scope of the data gathered. Existing equations have been applied to predict flowing pressures and compared with experimental data. New correlations have been developed. INTRODUCTION The increased economic pressure on the domestic oil industry in the United States has constantly required the use of new techniques and equipment designed to reduce the cost of finding and producing oil and gas. Since tangible items are most readily apparent in economic analysis, the advent of lower-cost well completions was inevitable. One of the methods used to reduce costs which has received widespread attention is the slim-hole completion technique where tubing is used as the well casing and in which small conduits are used for tubing if necessary. Small conduits, defined by Kirkpatrick1 as "11/4-in. diameter nominal tubing and smaller for tubing flow and less than twice the 11/4-in. diameter nominal tubing internal flow area for annulus flow", have also found widespread usage as siphon strings for de-watering gas wells and as "kill" strings in deep high-pressure oil and gas wells. The growing use of small-diameter tubing has resulted in an increased need for development of improved methods to measure or predict flowing bottom-hole pressures since the physical dimensions generally preclude the use of subsurface-recording pressure gauges. Even in the cases where small bombs are available, the relatively high velocities encountered at nominal flow rates make it necessary to use excessive weight bars or special hold-down devices. Attempts to use recognized correlations to accurately predict flowing or gas-lift performance in wells equipped with small conduits have been generally unsuccessful. Insufficient field data were available to allow the development of a correlation on this basis, and an experimental approach was applied in an attempt to obtain a workable relation. The experimental approach used to obtain the data presented in this paper was actually a compromise between a field installation and a laboratory study. A test well 1,000 ft in length was used to obtain flow data on single-phase liquid, single-phase gas and two-phase water-gas flowing mixtures. Liquid rates up to 2,200 B/D and gas rates up to 3 MMcf/D were used in the single-phase flow studies. Two-phase flow rates from 100 to 600 B/D with gas-liquid ratios from 500 to 8,000 cu ft/bbl were recorded. Experimental data were obtained for single- and two-phase flow through 1-in and 11/4-in. nominal tubing, and through the annuli between 1- and 2-in. and 11/4- and 2%-in. nominal tubing strings. Experimental results for the two-phase flow are compared to the Poettmann-Carpenter correlation2 which is widely used as a comparative standard for development of multiphase flow predictions in flowing and gas-lift wells. Correlations developed by Tek,3 Baxendell and Thomas" were also investigated. The experimental data recorded herein fell in between the two flow regimes as defined by Ros," and this correlation also failed to yield satisfactory results. The fact that existing correlations failed to confirm the experimental data led to the need for development of a new correlation. Although a two-phase flow study was the primary objective of this investigation, data were also recorded for single-phase flow of water and gas, and constants were developed relating to pipe roughness and equivalent diameters for annular flow. These single-phase studies assisted materially in the development of certain of the two-phase flow results. Considerable previous work has been published which presented relationship of surface measurements to bottom-hole condition. The works of Buthod and Whiteley,6 Jones,' Poettmannb and the Texas Railroad Commission" are classic examples of the successful use of mathematical relationships which allow acceptable predictions of subsurface pressures, when gas is the flowing fluid. Darcy and others have derived relationships which may be used with minor modifications to predict subsurface flowing conditions in injection and water-supply wells. As previously stated, the application of the single-phase flow relationships

By M. I. Jacobson, A. S. Yue, A. E. Vidoz, F. W. Crossman

An equation governing the concept of constitutional supercooling under the combined effect of concentration and temperature gradients was used to produce platelike Al-CuAl2 eutectic composites for mechanical properties studies. Compression specimens were prepared from a single-colony Al-CuA12 eutectic composite ingot, 2 in. in diam and 12 in. long. The specirrzens were cut such that the platelets were oriented parallel, 45 deg, and perpendicular to the compression direction. Since the ingot was of eutectic composition, The aluminum-rich matrix could dissolve 5. 7 wt pct Cu in solid solution, and therefore could be strengthened by precipitation hardening. Specimens were tested at room temperature and elevated temperatures in the unidirectionally solidified, solution-treated, and solution-treated plus aged conditions. The results were compared with those for the conventionally cast and extruded specimens. For the controlled material, the highest strengths were obtained with platelets oriented parallel to the compression axis. In the unidirectionally solidified condition, 0.2 pct offset yield strength was 32,000 psi; however, this was increased to 59,000 psi by solution treatment, and further increased to 90,500 psi by solution treatment and aging. The attainment of high compressive strengths in the Al-CuAl2 eutectic composites was interpreted in terms of the buckling of elastic CuAl2 platelets in the plastically deformed a aluminum matrix. SINCE the discovery of high-strength whiskers,' scientists and engineers have made significant progress toward incorporating these whiskers into metallic matrices, forming composites for basic studies and structural application. The general procedure is to produce the whiskers first and then to bind them together with a ductile matrix. The production of whisker-reinforced composites requires tedious handling techniques,, particularly when it is desired to align the whiskers unidirectionally. Furthermore, the interfacial bond between the whisker and the matrix is frequently poor3 so that the resulting composite has strengths lower than expected. These disadvantages are generally true for any metallic composite produced by physically mixing the components. It is possible to eliminate these shortcomings by growing whiskers directly in the matrix material by eutectic solidification.4-8 In eutectic solidification, the matrix phase and a whisker phase are grown approximately simultaneously from a liquid of the same overall composition at the eutectic temperature. If the solidification process is controlled by varying the freezing rate, the temperature gradient, and the impurity content, platelike or filamentlike whiskers are produced parallel to the growth direction. The morphology of the grown-in reinforcement, i.e.. plates or rods, generally depends on the volume fraction9 of the dispersed phase present in the eutectic mixture. Since the unidirectional eutectic solidification is a one-step process, i.e., the liquid-solid transformation process, an excellent interfacial bond between the matrix and whisker is obtained. An additional advantage is that no special handling technique for whiskers is needed. In recent years, many investigators10-13 have studied the effects of growth variables on the micromorpholo-gies of binary eutectic alloys produced by controlled solidification. The study of their mechanical properties was initiated by Kraft and coworkers14-16 who found that the strength of cast A1-CuA12 eutectic alloy can be increased threefold by unidirectional solidification. In the A1-AL3Ni system, a strength of 50,000 lb per sq in, was reported for the unidirectionally solidified eutectic alloy, a value five times higher than for conventionally cast material. Thus, the unidirectionally solidified eutectics can be used as fiber-reinforced composite materials. In this paper, we shall first use an equation17 as a guide for the production of eutectic composites in general and the Al-33 wt pct Cu eutectic in particular. Experimental data supporting the theoretical prediction are given. Second, the compressive properties of the grown A1-33 wt pct Cu eutectic were thoroughly investigated in terms of platelet orientations, thermo-mechanical treatment, and temperature. The experimental data are interpreted in terms of a buckling model of fibers in elastic fiber-plastic matrix metallic composites. EXPERIMENTAL PROCEDURE Crystal Growth. The following experimental procedure was adopted for the production of controlled microstructures in the A1-33 wt pct Cu eutectic alloy. The controlled solidification was accomplished with a movable resistance-wound radiation furnace. Fig. 1 is a schematic drawing of the solidification apparatus. A water-cooled chiller was placed into a degassed high-purity graphite crucible containing the charge. Rubber stoppers wrapped with aluminum foil were used to seal both ends of the quartz tube through which a dried argon atmosphere was passed under a slight positive pressure. At both ends of the quartz tube, radiation shields were used to minimize heat loss. The quartz tube was held in place by two steel clamps and the furnace was drawn vertically by means of a steel cable against the steel truss which permits the furnace to move without touching the tube. The drive mechanism consisted of two pulleys, a counter weight.

Jan 1, 1969

By Dwight H. Seely, Louis R. Records

A process for low-temperature dehydration of natural gas utilizing Joule-Thomson effect in expansion through a throttling orifice has been tested in a full-scale field installation. The results of these tests are presented in the form of performance curves from which the process may be easily evaluated. The effect of separation temperature on condensate recovery from the process is also shown. INTRODUCTION The transportation of natural gas from producing well to the consumer has always encountered the problem of hydrate prevention. This problem has become increasingly important in the past ten years due to the rapid increase in produced gas volumes, production pressures, transportation pressures and distance from producing wells to consumer. Natural gas, as normally produced from gas or gas-condensate wells, is saturated with water vapor at well-head conditions of temuerature and pressure. The solution of the hydrate problem require; but one basic process — dehydration of the gas to a water content which will result in a water dew-point below the minimum temperature to be encountered from the producing well to the point of consumption. Much of the recent development of gas and gas-condensate reserves in the Gulf Coast Area has been in locations which are accessible only by water. High well-head pressures, pipeline construction and maintenance costs and the desirability of final central gas-condensate separation facilities have stimulated the development of dehydration equipment which can be installed at each well and which will permit hydrate-free transportation of both gas and condensate in the same line to central facilities. There are four types of natural gas dehydration processes now used: 1. Adsorptive processes. 2. Absorptive processes. 3. Chemical reaction processes. 4. Refrigeration processes. The first three of these processes are indirect in that they require use of adsorbents, absorbents or reactive chemicals. These materials require regeneration and part of the total gas stream is consumed in the regenerative process. Indirect processes have a wide range of flexibility as defined by allowable operating pressure and temperature, but most are not easily adapted to automatic operation. The refrigeration process described in this paper was designed for installation at the producing well-head. It requires no regenerative cycle and with normal well-head temperatures no external source of heat. The flexibility of this process is limited only by the pressure drop which may be allowed between well-head and transportation line. THEORY There are three basic physical concepts involved in the low temperature dehydration process. These are: 1. Formation of hydrocarbon hydrates. 2. Joule-Thompson effect resulting from the expansion of gaseous mixtures through a throttling orifice. 3. The equilibrium composition characteristics of water vapor and gaseous hydrocarbon mixture.. The chemical composition and physical structure of hydrate; have been described by several investigators.3,4,5,10 Specific conditions of temperature, pressure and composition as well as the requirements for turbulence and presence of free water necessary for hydrate formation have been described by Katz.6 Natural gas hydrates, as they are found in plugged gas pipe lines, have the appearance of packed snow. The mass of these hydrates has low continuous porosity and permeability. Joule-Thomson effect. or the reduction in temperature which occurs when natural gas is throttled throusll a restrictive orifice, is the basic phenomenon which permits efficient use of refrigeration for the purpose of dehydrating natural gas. Joule-Thomson coefficients for gafeous mixture; of methane with ethane and with butane have been reported by Buder.-I~olzer, Sage and Lacey.2 Brown1 predicted temperature drops for pressure drops from enthalpy-entropy calculations. Aside from this work there were no fundamental data found which would be applicable to natural gas mixtures of varying spe-

Jan 1, 1951

By Dwight H. Seely, Louis R. Records

A process for low-temperature dehydration of natural gas utilizing Joule-Thomson effect in expansion through a throttling orifice has been tested in a full-scale field installation. The results of these tests are presented in the form of performance curves from which the process may be easily evaluated. The effect of separation temperature on condensate recovery from the process is also shown. INTRODUCTION The transportation of natural gas from producing well to the consumer has always encountered the problem of hydrate prevention. This problem has become increasingly important in the past ten years due to the rapid increase in produced gas volumes, production pressures, transportation pressures and distance from producing wells to consumer. Natural gas, as normally produced from gas or gas-condensate wells, is saturated with water vapor at well-head conditions of temuerature and pressure. The solution of the hydrate problem require; but one basic process — dehydration of the gas to a water content which will result in a water dew-point below the minimum temperature to be encountered from the producing well to the point of consumption. Much of the recent development of gas and gas-condensate reserves in the Gulf Coast Area has been in locations which are accessible only by water. High well-head pressures, pipeline construction and maintenance costs and the desirability of final central gas-condensate separation facilities have stimulated the development of dehydration equipment which can be installed at each well and which will permit hydrate-free transportation of both gas and condensate in the same line to central facilities. There are four types of natural gas dehydration processes now used: 1. Adsorptive processes. 2. Absorptive processes. 3. Chemical reaction processes. 4. Refrigeration processes. The first three of these processes are indirect in that they require use of adsorbents, absorbents or reactive chemicals. These materials require regeneration and part of the total gas stream is consumed in the regenerative process. Indirect processes have a wide range of flexibility as defined by allowable operating pressure and temperature, but most are not easily adapted to automatic operation. The refrigeration process described in this paper was designed for installation at the producing well-head. It requires no regenerative cycle and with normal well-head temperatures no external source of heat. The flexibility of this process is limited only by the pressure drop which may be allowed between well-head and transportation line. THEORY There are three basic physical concepts involved in the low temperature dehydration process. These are: 1. Formation of hydrocarbon hydrates. 2. Joule-Thompson effect resulting from the expansion of gaseous mixtures through a throttling orifice. 3. The equilibrium composition characteristics of water vapor and gaseous hydrocarbon mixture.. The chemical composition and physical structure of hydrate; have been described by several investigators.3,4,5,10 Specific conditions of temperature, pressure and composition as well as the requirements for turbulence and presence of free water necessary for hydrate formation have been described by Katz.6 Natural gas hydrates, as they are found in plugged gas pipe lines, have the appearance of packed snow. The mass of these hydrates has low continuous porosity and permeability. Joule-Thomson effect. or the reduction in temperature which occurs when natural gas is throttled throusll a restrictive orifice, is the basic phenomenon which permits efficient use of refrigeration for the purpose of dehydrating natural gas. Joule-Thomson coefficients for gafeous mixture; of methane with ethane and with butane have been reported by Buder.-I~olzer, Sage and Lacey.2 Brown1 predicted temperature drops for pressure drops from enthalpy-entropy calculations. Aside from this work there were no fundamental data found which would be applicable to natural gas mixtures of varying spe-

Jan 1, 1951

By P. S. Kotval, H. Hahell

PRECIPITATION of M23C6 carbides at grain boundaries in austenitic steels and nickel base superalloys has received considerable attention. Hatwell and Berghezan,1 in a study using carbon extraction replicas, observed that dendritic growth of the M23C6 carbide phase occurred at grain boundaries in austenitic steels. Merrick and Nicholson2 have observed that in thin foils of "Nimonic 75" alloy the precipitation of M23C6 carbide was discontinuous at grain boundaries. Lewis and Hattersley3 have suggested that the type of M23C6 precipitation observed in Ni-Cr austenites represented the early stages of discontinuous precipitation. In a more recent study, Singhal and Martin4 have concluded that grain boundary M23C6 precipitation involves the migration of an austenite grain boundary by a mechanism very similar to that proposed by Tu and Turnbull.5 Tu and Turnbull's suggestion essentially involves grain boundary migration under the driving force arising from the difference between the surface free energies of the opposite sides of the plate. Thus, Singhal and Martin's observation4 implies that the first stage of discontinuous precipitation has taken place and that the grain boundary has provided a diffusion short circuit for the sub-stitutional solute atoms (principally chromium) which assist the preferential growth of the M23C6 plate in contact with the grain boundary. However, no evidence of the characteristic cellular morphology typical of discontinuous precipitation was found in Singhal and Martin's studies. Presumably, this is due to the low volume fraction (i.e., low supersaturation of solute) of the precipitating carbide reported by Singhal and Martin.4 Recently, Raymond6 has studied precipitation of the M23C6 carbide in Incoloy alloy 825 and shown that the growth of this phase is perpendicular to grain boundaries at 1400°F and in the plane of the grain boundary at 1700°F. The former aging condition resulting in discontinuous or "cellular" precipitation. Raymond has suggested an explanation for this behavior based on the relative rates of chromium diffusion by volume and grain boundary diffusion at the two different aging temperatures. In the course of a recent investigation on precipitation behavior in several ' strengthened superalloys, precipitation of M23C6 carbide at grain boundaries was studied. Under conditions of a high degree of supersaturation, the M23C6 carbide precipitates in the discontinuous or cellular morphology in Waspalloy (Ni-18.51 Cr-2.0 Fe-3.53 Mo-1.16 Al-2.78 Ti-0.09 C). This note presents electron microscopy observations of this mode of precipitation and its effect on mechanical properties. Specimens of Waspalloy after "solution" heat treatment at 1950°F show essentially single phase matrix with a few residual particles of "primary" MC carbide. In normal commercial heat treatments, precipitation of Ni3(Al,Ti) ordered fcc r' phase occurs throughout the matrix and M23C6 precipitates as globular particles at the grain boundaries. In these commercial heat treatments the degree of supersaturation during precipitation is low. However, if specimens of Waspalloy are quenched from the solution heat treatment temperature of 1950°F and then aged at an aging temperature where the degree of supersaturation is high, discontinuous precipitation of M23C6 occurs. Figs. 1 and 2 show thin foil micrographs of Waspalloy, solution heat treated at 1950°F, water quenched, and aged at 1292° and 1598°F, respectively, for 500 Fig. 1—Thin foil of Waspalloy, solution heat treated at 1950°F for 1 hr, water quenched, and aged for 500 hr at 1292°F. Magnification 15,500 times. Fig. 2—Thin foil of Waspalloy, solution heat treated at 1950°F for 1 hr, water quenched, and aged for 114 hr at 1598° F. Magnification 13,000 times.

Jan 1, 1970

By F. X. Meagher

Vertical slot raise driving from bottom up has always been a hazardous, inefficient, high cost operation. The introduction of the Simba 5 drill rig has enabled this type of raise to be drilled accurately from the top down and to be blasted in stages from the bottom up. Safety, high efficiency and low cost were the main criteria in opting for this method. Drop raises with the Simba 5 at Geco have been successfully drilled and blasted up to 115 feet, and this is close to the maximum length of raise that can be drilled and blasted efficiently with Simba 5. A look into the future would indicate a rig capable of drilling up to 200 foot raises with the same accuracy of Simba 5 to 115 feet.

Jan 1, 1974

By Kenneth A. Brunk

"This address discusses how ""Mineral Processing Technology"" can play a major role in the life and profitability of a mining company. Examples of past and present technological breakthroughs and their impacts will be examined. Also, the future of processing technology will be emphasized.IntroductionThis talk will center on the role of technology as an important component of a business plan for mining companies. I'll attempt to explain how I see technology development as an underpinning of a successful mining company. We will examine an example of a technology that has resulted in a re-birth of segments of the industry, examine a technology life cycle and discuss technology as it relates to ore reserve replacement. Also, we will touch on technology in today's mining company and propose some food for thought for those designers of corporate organizations."

Jan 1, 1997

By J. E. Burke, A. M. Turkalo

IN 1923 Desch¹ pointed out that the grains in a metal which is anisotropic with respect to its thermal coefficient of expansion would contract differently upon cooling, and that the stresses developed might approximate the plastic strength of the metal. More recently Boas and Honeycombe2-5 studied the behavior of several metals upon thermal cycling and observed that the stresses developed in arlisotropic metals are great enough to produce slip lines in individual grains and a roughening of the specimen surface. This phenomenon they have named "thermal fatigue." The mechanism they propose involves essentially a kneading of the grains, the deformation being alternately in compression and tension in a given grain as the temperature is changed in one direction and then the other. The present work was undertaken to investigate the possibility that an additional mechanism might operate to produce plastic deformation during thermal cycling—a "thermal ratchet" that depends upon a combination of grain boundary flow to relax the stress that develops between differently oriented grains upon raising the temperature and transcrys-talline slip to relax the oppositely directed stress which develops on lowering the temperature. Thus, thermal cycling should produce a nonreversible distortion such that certain grains will change shape differently from their neighbors with a simultaneous displacement being produced at the grain boundary. Temperature Dependence of Grain Boundary and Grain Strength The critical resolved stress for the initiation of slip in metal grains is only mildly affected by temperature." For example, in cadmium it decreases from 0.15 to about 0.05 kg per sq mm when the temperature is increased from 20° to 458°K and further temperature increase causes little further decrease. On the other hand, the work of KG1 indicates that the grain boundaries behave in a viscous fashion that can be described8 by the expression: t = BVexp(Q/RT) [1] t is the shearing stress on the boundary; B, a constant; V, the flow rate at the boundary; Q, the activation energy for grain boundary flow; R, the gas law's constant; and T, the absolute temperature. Eq 1 indicates that the stress necessary to cause a given grain boundary flow rate, V, decreases rapidly with increasing temperature. The value of the constant B is such that at sufficiently low temperature and ordinary strain rates deformation will occur preferentially by slip rather than by grain boundary flow. There is considerable evidence to indicate Consider the bicrystal shown in Fig. 1. In grain 1 the slip plane lies 45 " to the boundary while in grain 2 the slip plane is 90" to the boundary. The coefficients of expansion of the grains in a direction parallel to the length of the crystal are a1 and a, with a, > a2 for the orientations shown. The sequence of events that can occur upon heating and cooling this specimen is illustrated schematically in Fig. 2. Initially there is assumed to be no stress in the specimen (A). Upon heating, grain 1 attempts to become longer than grain 2, but is constrained by grain 2. Thus grain 1 is loaded in compression and grain 2 is loaded in tension, and a shearing stress is present across the boundary (B). As the temperature is increased, the stress will build up, and finally grain 1 will be plastically deformed by slip, since the greater stress is resolved on its slip planes. Any further heating will result in more slip and the stress will remain constant until some temperature T* is reached where the stress can be relaxed by grain boundary flow.† At this relaxation temperature (C) a step will appear between grain 1 and grain 2. Further heating above T* will cause grain 1 to become relatively longer, but no stress will appear because the grain boundary is too weak to support the stress (D). Upon cooling again, at T* (E), the grain boundary will again be able to support a shearing stress, and upon cooling further, grain 1 will be loaded in tension and grain 2 in compression (F). When the decrease in temperature below T* is sufficient to impose the critical shear stress upon the slip plane of grain 1, it will be stretched by slip.

Jan 1, 1953

By D. J. Mottern, F. Wald

SEVERAL systems have been investigated by Bates, Wald, and weinstein&apos; to determine the compatibility of pure PbTe with various metals. This was accomplished by experimentally determining the direction of the reaction given by Eq. [I]: The direction of this reaction is very important if alloys of the PbTe system are to be used in thermoelectric generators because the presence of free lead in the matrix, followed by incipient melting in the vicinity of the hot junction, could cause a bonding failure. According to anssen,&apos; the Au-Te system contains only one stable compound, AuTez. The initial alloy which was reacted was therefore of the composition AuTez + 2Pb. Ten-gram samples of PbTe plus 1, 10, 20, 30, 40, 50, and 70 at. pct Au were encapsulated in carbon-coated quartz capsules in vacuo. All materials were of semiconductor (99.999+ pct) purity. Carbon coating was used to prevent reaction of the quartz with any of the alloying constituents (the solubility of carbon in the constituents of the alloys is negligible). Each capsule was then placed in a thermal analysis furnace, melted, and cooled through the transformation region. Thermal arrests were monitored on a strip chart recorder. Each sample was subsequently examined microscopically after standard grinding and polishing techniques were applied. For better contrast between the phases, the samples were etched in Murakami&apos;s etch; however, both phases could be identified without etching. Several of the samples were ground into powder, stress-relieved, and X-rayed in a Debye-Scherrer camera using nickel-filtered Cu-Ka radiation. The phase diagram shown in Fig. 1 indicates that the pseudobinary system exists as a simple eutectic with no measurable (<I pct) solid solubility at either limit. Figs. 2,3, and 4 are photomicrographs of the structures obtained with 20, 40, and 50 at. pct Au, respectively. At higher concentrations of gold (>40 pct) slight divorcement of the eutectic occurred, apparently due to a) the difference in density between gold and PbTe (19.6 and 8.25 g per cu cm, respectively) or b) the nonideality of the liquid as noted by the curvature of the liquidus lines. The eutectic temperature was determined to be 742° ± 5°C. The composition of the eutectic was determined by extrapola-

Jan 1, 1969

The research described in this report was conducted under a cooperative research agreement between the U.S Bureau of Mines Twin Cities Research Center (TCRC), Cleveland-Cliffs Inc. (CCI), and three operations in Northern Michigan managed by CCI: the Empire and Tilden surface taconite mining operations, and the Central Shops maintenance facility. All of these operations are in or near Ishpeming, MI. The Human Factors Research Group at TCRC is responsible for designing, planning, and conducting the research, and reporting on the findings. This project was carried out in order to investigate the high prevalence of back injuries being experienced by workers employed at the three CCI Northern Michigan sites, In an analysis of Company accident records for workers employed at these sites, it was determined that back injury problems confronting the CCI sites mirror those confronting the entire mining industry.

Jan 1, 1994

By J. Racinais, P. Vincent

"In September 2011, Menard Oceania (MO) was engaged by Mac Mahon John Holland Joint Venture (MJHJV) to provide ground improvement solution for the $34bn Ichthys LNG development. With close to 400,000m2 of mangrove swampland set to be reclaimed and improved, this project was a great opportunity to showcase the technical, commercial and environmental benefits that Dynamic Replacement (DR) ground Improvement technique can provide. The ground improvement works involved complete design and construction for the Ichthys LNG site located at Blaydin Point on a low lying peninsula in Darwin Harbour. Dynamic replacement and stone columns technique were selected to treat intertidal mangrove mud to achieve required bearing strength, stability and limit settlement to an acceptable levels. The site is underlain by a 3m to 5m thick layer of highly organic mangrove muds with very soft shear strength ranging from 0kPa to 12kPa at depth. The site is exposed to daily sea water level tidal variations of up to 8m, which created significant constructability constraints and slope instability risks. This paper presents the design philosophy, the process involved in the selection of the construction methods, the site constraints encountered during the works and a review of the results achieved, quality control and post constructions performance.INTRODUCTIONInpex Browse, Ltd (Inpex) and its partner Total are developing the Ichthys gas field to pipe gas to onshore facilities at Blaydin Point on the south side of East Arm in Darwin Harbour. The proposed LNG plant consists of gas receiving facilities, 2 x 4.2Mtpa nominal capacity LNG trains, LPG and condensate production facilities, product storage and export facilities, a module offload facility (MOF), a flare pad (FP) and associated off plot facilities.The proposed on-shore facilities are located on extremely soft intertidal mangrove muds, therefore an appropriate ground improvement was required to achieve required strength and stability of site works and limit long term settlement to an acceptable level.Various ground improvement techniques were studied to select the most suitable for the ground conditions and site constraints encountered at the Blaydin point site. Dynamic replacement technique was selected for onshore section to improve soft mangrove mud to depths of 5.5m and Stone Columns (SC) technique was selected for MOF off-shore section to improve intertidal deposits to a depth of 2.5m.This paper presents DR design and construction works performed between December 2012 and August 2013 at Flare Pad Area."

Jan 1, 1900

By O. Tsuge, G. Hoffman

ITmk3®(Iron Technology Mark III) is an innovative new ironmaking technology whereby high quality iron nuggets are produced directly from iron ore fines and coal in a rotary hearthfurnace1). The reaction mechanism has been investigated in detail through fundamental laboratory research2)3), and the ITmk3 process has progressed from the laboratory to commercialization by the success of the pilot plant tests initiated at Midrex’ Technical Center and at the Kakogawa Bench Plant (KBP) located at Kobe Steel Ltd. Kakogawa Steel Works4)5). Pilot operations have demonstrated rapid production of the iron nuggets with complete metal/slag separation at a relatively low operating temperature. The Kakogawa Bench Plant (KBP) in Japan has logged 21 days continuous operation during which high quality iron nuggets were produced directly from fine ore and coal. The operation technology and the engineering data obtained from these pilot tests were instrumental for the scale-up of the ITmk3 process for the Mesabi Nugget Corp. pilot demonstration plant, which is located at Cleveland Cliffs Inc. Northshore Mining iron ore pellet plant in Silver Bay, MN. The ITmk3 process is an ideally suited technology for siting at the iron ore mine, as it allows the economical production of a value-added merchant iron product.

Jan 1, 2003

The Secretary : The work of Mr. A. E. Outerbridge, Jr., of Philadelphia, first made known in his paper on " The Mobility of Molecules of Cast-Iron," read at the Pittsburgh Meeting of the Institute, in February, 1896, has been reviewed by the Committee on Science and the Arts of the Franklin Institute, whose report, dated May 5, 1897, is accompanied with a table of tests made by the Committee, and amply confirming the statements of Mr. Outerbridge. Concerning the originality and novelty of his investigation, the Committee says: " The fact that a certain molecular change takes place in cast-iron in the course of time has been known and recognized by many persons for a long time, and that this change tends to relieve the internal strains and render the casting tougher has often been noticed and acted on, although in a very crude way; but, so far as the sub-committee has been able to learn, Mr. Outerbridge has been the first to make a careful study of this, and to note that the change may be hastened by impact, and the whole effect produced in a short time, and also to make a scientific study of the phenomenon. We believe great credit is due him for the initial observation and the careful work dependent thereon. The results were first given to the public in a paper read before the American Institute of Mining Engineers, on February 20, 1896. This aroused a wide-spread interest and discussion among users of cast-iron, and so far as the sub-committee has been able to determine, it has not been shown that anyone, either in this country or abroad, has antedated Mr. Outerbridge in his work in this line. The Franklin Institute therefore recommends the award to him of the John Scott Legacy Premium and Medal." This report has not been published, hut I have had the opportunity to read it in manuscript. The table of testa accompanying it comprises 91 tests of " rumbled" and an equal number of " not rumbled" companion-bars of cast-iron, 26 by 2 by

Jan 1, 1898

By Alan Stanley

THE Maclntyre Development of National Lead Co. is located at Tahawus, N. Y., in the heart of the Adirondack Mountains. Operations involve the mining and concentrating of a titaniferous iron ore to produce ilmenite and magnetite concentrates. A general description of the operation and metallurgy has been given by Frank R. Milliken.1 Pigment plant production demands that the MacIntyre mill produce a 44.7 pct. TiO2 ilmenite concentrate. To achieve the required ilmenite grade and tonnage it is important that the table concentrate grade be closely controlled. Unfortunately, however, the titaniferous orebody which feeds the Maclntyre mill is not uniform. Ore dressing characteristics vary from one end of the orebody to the other, and from one level to the next.. The changeable nature of the mill feed precludes a single adjustment of the equipment for long periods of time. Thus the operators must constantly watch the equipment to insure a uniform concentrate from the fine and coarse tables and Wetherills, or dry magnetic separators. Chemical assaying of mill products requires about 4 hr from the time the sample is taken until assay results are obtained, and this is available only on a two-shift basis. The ore may change rapidly, even several times during a shift, so that assay results lose most of their control value by the time they are reported to the mill operating crew. Members of the crew have therefore tried to evaluate the table and Wetherill concentrate by visual inspection, since through long experience the shift operators, under most circumstances, can gage closely the grade of the mill products. However, there are times when the, physical nature of the ore is radically different from normal. Under these conditions visual inspection is of no value, and at such times final ilmenite as low as 43 pct TiO2 has been produced and shipped before the assay results have been received. The specific gravity method of assaying for TiO2 has been attempted to eliminate the shipping of ilmenite below normal grade as well as to help control day to day and hour to hour mill production. Table I shows the minerals found in the Maclntyre ore along with their average weight proportions and specific gravities. The first two products considered for the specific gravity method were fine and coarse table concentrates. It was reasoned that these products were essentially ilmenite with the higher specific gravity gangue minerals. Since they were always produced the same way, and the desired grade of TiO2 was always constant, the specific gravity of these materials would increase or decrease as the amount of ilmenite increased or decreased. Thus for table concentrates which assayed 40 pct TiO2 a constant gravity would invariably be obtained, and as the TiO2 value changed the specific gravity would change in direct proportion. The third product considered was Wetherill ilmenite. It was assumed that a desired grade of 44.7 pct TiO2 would also always contain the same amount and type of gangue minerals along with the ilmenite, and thus would always have the same specific gravity. As the TiO2 value of the ilmenite concentrate changed so would its specific gravity. Dr. Kenneth Vincent, chief metallurgist of the Baroid Division of National Lead Co. at Magnet Grove, Ark., ran specific gravity tests on 17 samples of the desired products. The lowest specific gravity reading assayed the lowest in TiO2 and as the specific gravity increased the trend was for the TiO2 assay to increase, see Fig. 1. Since these results warranted further investigation, a 500-g capacity Torsion balance and 250 ml Le Chatelier specific gravity bottles were obtained. [ ] Shift samples of fine table concentrate, coarse table concentrate, and final ilmenite were tested. Each sample was split and 85 g weighed on the Torsion balance. The Le Chatelier bottle was filled with water to a zero mark. To avoid wetting the neck of the bottle it was found necessary to do this

Jan 1, 1952

OCHRE is a semimineral composed by Nature of earth and a tincture of yellow caused by a fumosity of lead ore. By itself it is a material without any [38] metal, although when it is used in smelting it helps to melt the harsh and sour ores of metals. I do not know that it has any other use, except to painters. Bole is also a red viscous earth which has a very astringent and drying nature. It has no very apparent smell or taste, and I think that the cause of its redness lies in the fumosities of iron ore, for it is a companion to this and is found in its mines. It is an efficacious medicine against any poison and in this capacity has an action like terra sigillata* or perhaps better. In

Jan 1, 1942

By Jessica M. Wempen, Dallan J. Coons, Bailey S. Simmons, Michael K. McCarter

Gate-road yield pillars are subject to increases in stress as the longwall face advances toward the pillars. Increases in pillar stress can be inferred by measuring roof/floor convergence surrounding the pillar. This paper presents a case study of convergence measurements surrounding a two-entry gate-road yield pillar in the head gate of a coal mine. Convergence was measured over a six-month period, as the longwall face approached and passed the pillar. Measurements were collected at eight locations surrounding the pillar: four locations in the travelway and four locations in the beltway. In addition to convergence stations, the pillar was instrumented with an array of seismometers. In future analysis, convergence measurements will be compared to seismic interpretations. This study reports on the geology and geometry of the longwall panel, the roof and rib support, the change in convergence over time, and the physical properties of coal and parting. Additionally, the convergence measurements are compared to pillar safety factor distributions derived from a finite element model. The convergence measurements contribute to the knowledge of when yield pillar abutment loading, caused by the encroaching longwall, is first detected. Knowing when abutment loading begins to yield the pillars can help define when standing secondary roof supports are required for head gate entry support.

By W. Blake, J. Whyatt

Sixty years of rock bursting in the Coeur d&apos;Alene district has taught painful lessons and led to a number of practical advances in controlling rock-burst hazards. This paper summarizes these lessons, concentrating on practical measures that have been successfully adopted to reduce hazards. These lessons are explained in the context of district mining history and current understanding of rock-burst phenomena. Overall, the paper provides the practicing mine engineer with an appreciation of rock-burst hazards and an overview of practical measures that can be used to control these hazards in the context of Coeur d&apos;Alene district experience.

Jan 1, 2003

By A. E. Schuetz, A. E. Roswell, W. R. Hibbard

THE drawn wire texture of body-centered cubic iron,&apos; tungsten,&apos; and molybdenum~ as been determined to be a [110] direction parallel to the wire axis. The purpose of this study is to extend the available information on body-centered cubic wire textures to other metals and alloys. Wires were produced using hand wire rolls and dies as given in Table I. In addition, attempts were unsuccessful to draw wires from chromium, vanadium (Vanadium Corp. of America), and tungsten (Cleveland Tungsten Inc.). Although it is known that wires can be made from these materials, suitable techniques were not readily adaptable. Where necessary, wires were polished and etched to form flat ribbons 0.005 to 0.007 in. thick, and transmission X-ray patterns were taken using molybdenum radiation with the specimen tilted 0 degrees from the perpendicular toward the beam to critically cover the wire axis. Analyses were made of (110), (002), and (112) reflection circles. In all cases reflection maxima indicated the texture to be a single [1101 deformation fiber, as illustrated by Fig. 1 for molybdenum. In the case of the hot-worked ß brass, a second texture, [loo], was also found, but this is believed to be the result of recrystallization since it has been reported for re-crystallized molybdenum wires&apos; and it was not present in the cold-drawn ß brass. The difference in drawability between the 51.92 pct Cu ß brass and the 62.5 pct Cu ß brass (containing some grain boundary a due to incomplete quenching) is quite striking, since the latter could be cold worked readily while the former had to be hot worked to avoid cracking. Summary The deformation texture of drawn body-centered cubic wires of ß brass, iron, molybdenum, niobium, and tantalum is essentially a single [110] fiber as predicted by theory.&apos; Acknowledgment The authors wish to thank the suppliers of the metals listed in the text, and the Grant-in-Aid from the Research Fund of the Society of the Sigma Xi and Scientific Research Society of America which made possible the purchase of X-ray equipment.

Jan 1, 1952