Search Documents

By J. K. Pandey, ebashish Mishra, D. P. Mishra, N. K. Mohalik, S. K. Ray

The increasing demand for coal and depletion of shallow depth reserves are pushing towards deeper mining. In deeper coal mines with multiseam workings, the problem of ventilation surges many folds primarily related to air quantity requirement, heat, humidity and spontaneous heating/fire in goaved (gobbed) out areas. The paper describes the design of a new approach to improve the ventilation system of a real-life deep underground coal mine with multiseam workings. For this, the ventilation problem of one deep underground coal mine 6&7 pits Bhutgoria Amalgamated Colliery of Tata Steel Ltd. with multiseam workings has been studied in detail to determine an appropriate solution. A ventilation survey of the mine and computer simulation of the ventilation network has been carried out to reach a practical solution. Ventilation survey results have been analysed to develop a representative ventilation network of the mine for both qualitative and quantitative analysis. Further, computer simulation of the ventilation network of the mine has been performed to virtually verify the application of a highcapacity booster fan in the present ventilation circuit without disturbing the vulnerable areas. Field validation is also carried out after the implementation of the solution in the mine to determine its efficacy. Thus, the findings of this paper can be directly applied for the installation of booster fans to achieve the required air quantity in deep underground coal mines with multiseam workings having spontaneous combustion liabilities of upper seam goaved out areas.

Jun 2, 2022

By Kurt Westerlund

Three years operating experience of the FLUXFLOW waste heat boiler (WHB) 20.000 nm3/0h at Boliden Rönnskär Sweden on a TBRC smelting galena (PbS). Operating experience from the Kivset flash WHB 11.900 nm3/h at Samim, Porto Vesme, Sardinia, Italy. Conceptual features of the 93.600 nm3/h FLUXFLOW (WHB) on the Isasmelt smelting in melt furnace for 180.000 t Cu/a at Mount Isa, Australia.

Jan 1, 1992

By Xintan Chang

MFIRE is a computer simulation program that performs normal ventilation network planning calculations and dynamic transient-state simulation of ventilation networks under a variety of conditions. The program is useful for the analysis of ventilation networks under the influence of natural ventilation, fans, fires, or any combination of these. MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters such as the development of new mine workings or changes in ventilation control structures, external influences (varying outside temperatures), and internal influences (fires). Extensive output enables detailed, quantitative analysis of the effects that the alteration will cause to the ventilation system. The program was developed at Michigan Technological University (MTU), Houghton, MI, with support from the Bureau of Mines. A personal computer (PC) version of the program was completed under contract for the Bureau by MTU. The purpose of this report is to document the installation and use of the PC version of the program MFIRE.

Jan 1, 1990

By Yi Luo

Simulation of the multi-entry and multi-crosscut (MEMC) ventilation systems commonly employed in U .S. underground coal mines can be very tedious, due to the large number of crosscuts with stoppings to be represented in the network models. In order to reduce the amount of work needed to build the models, a common practice is to represent a number of crosscuts with one equivalent airway. However, this introduces certain errors into the simulation results. In this paper, algorithms have been proposed to simplify the ventilation networks of common MEMC systems encountered in panel development operations. The algorithms can be used to reduce a MEMC system into one airway with an equivalent resistance and to determine the airflow distributions in the system and the leakages through the stoppings.

Jan 1, 2011

By H. Matsuoka, M. Kawata, K. Mitsuhashi, C. Tokoro, T. Kato

Copper sulfide minerals such as chalcocite, bornite, and chalcopyrite exhibit high floatability, thus they can be recovered as a froth product by adding only a collector in flotation process. However, when their surface is oxidized, the floatability decreases and the simple addition of collectors is no longer effective. In this case, flotation activators are required to improve the floatability. Sodium hydrosulfide (NaHS) acts as an activator for chalcocite and bornite by re-sulfurizing their oxidized surface portions. Nevertheless, the flotation conditions still require optimization in order to achieve a satisfactory recovery of copper minerals. This work addresses the study of the effect of pH and NaHS dosage on the flotation of a complex Chilean copper ore containing chalcocite, bornite, and chalcopyrite. Flotation experiments were conducted using a Denver-type flotation cell and by investigating the effect of two NaHS dosages (50, 100 g/t) and three pH values (8, 9, 10). Following this process, the surface interaction between the minerals and NaHS were analyzed using zeta potential measurements. INTRODUCTION In recent years in the mining area of metal resources, the complexity of ores and the fineness of grind required to liberate minerals have become serious problems. When ores are complex, several valuable minerals may interact with each other and reactions may become more complicated compared with an ore containing only one valuable mineral. Therefore, more processing steps may be required than for a simple ore. When the valuable minerals exist as fine grains, it is difficult to liberate them and more grinding time is required. Furthermore, the probability of collision of fine particles with bubbles in the flotation process declines and it takes much time to recover them. Flotation is one of the most applied methods to separate valuable minerals from unwanted ones using the difference of hydrophobicity (or hydrophilicity). In the flotation method, the air is fed to a cell filled with the pulp of the mineral of interest and agitation is implemented to introduce air and generate bubbles. The hydrophobic particles attach themselves to the bubbles and float along with the bubbles while the hydrophilic particles remain in the pulp. Copper sulfide minerals such as chalcocite (Cu2S), bornite (Cu5FeS4), chalcopyrite (CuFeS2) are widely known abundant copper resources. Generally, flotation is used to recover and concentrate these minerals. Copper sulfide minerals usually have high floatability. However when their surfaces are oxidized, their floatability becomes lower. When the sulfide surfaces are oxidized, activators are added before flotation to modify the surface property of the Copper sulfide minerals so that they can be floated. Sodium hydrosulfide, NaHS, is known as one of the activators. Zhao (2018) reported that NaHS is often used as a sulfurizer for oxidized sulfide minerals (Becker (2014), Clark (2000), Newell (2006), and Newell (2007)). In earlier work, the authors performed flotation tests on a sample of Chilean copper ore which contained chalcocite, bornite, and chalcopyrite using a Denver-type flotation apparatus. The sample was ground to P80 70 µm with a rod mill and ball mill. In these tests, the following conditions were used: natural pH (about pH 8.5), flotation time of 45 min, 60 g/t AP3477 (sodium diisobutyl dithiophosphate) as collector, and MIBC (methyl isobutyl carbinol) at appropriate dosage as frother. NaHS was applied at the dosage of 0, 67, and 120 g/t, respectively at the conditioning. The concentrates were collected at 6, 18, 30, and 45 min. The weights of the concentrates and tailing were measured and they were assayed for copper by ICP-AES (Optima 5300 DV, PerkinElmer Inc.). The flotation recoveries of the copper minerals were calculated from the results of MLA (mineral liberation analyser) (MLA 650, FEI) measurements.

Jan 1, 2019

By S. W. Ihle, L. J. Warren

A sample of garnet from the scheelite ore body on King Island, Tasmania, Australia, was upgraded and ground to produce an ultrafine portion suitable for micro-electrophoresis. X-ray and chemical analysis identified the garnet as andradite with some admixed grossular. At neutral pH the garnet particles were negatively charged, their zeta potential becoming rapidly more negative with increasing pH. An iso-electric point was found at pH 3.5. The effects on the zeta-potential of various electrolytes, hydrolyzable metal ions, and flotation collectors were also studied.

Jan 1, 1976

By J. D. Robertson

An in situ water sampling device has been developed to measure biologically-available or “labile” metals in natural waters and effluents. The active mechanism involves the use of a polyacrylamide gel layer to quantitatively control metal transfer to a trace-metal-adsorbing, gel-imbedded resin. Because the resin only adsorbs free metal ions (the gel sampler methodology is a kinetic speciation technique), and because metal bioavailability is related to the free-ion activity, the device provides a direct measure of the biological-availability of metals in the environment sampled. The prototype consists of a layer of ion-permeable polyacrylamide gel which separates the solution to be sampled from an ion exchange resin. Because approximately 90% of the polyacrylamide gel is water, mass transport through the gel is diffusion-controlled, and is therefore well defined. Metal ions are rapidly bound by the resin, creating a steep concentration gradient in the gel. The amount of labile trace metal that accumulates on the resin can be related directly to the concentration of the metal in solution, the exposure time and the molecular diffusion coefficient of the labile species. In addition, the passive nature of this device affords it the potential to address many of the limitations presented by conventional sampling methods, such as sample contamination introduced during collection or filtration and changes in trace metal speciation prior to analysis. Laboratory studies and limited field trials indicate that the sampler behaves as anticipated and illustrate that biologically- available metal concentrations in many environments are a small fraction of the total concentrations and often significantly less than the dissolved concentration. The implications of this on regulatory criteria are discussed. Additional field trials and correlation with bioassays are currently underway.

Jan 1, 2000

By Northcutt Ely

This volume summarizes mining and petroleum legislation in 25 jurisdictions of East Asia and the Pacific. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes: First, identification of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis of the laws governing mines and quarries and their products; and third, analysis of laws applicable to natural gas, petroleum, and related materials. Where pertinent, sections dealing with historical background or administration have been added. In countries where minerals are subject to control of States or Provinces, those areas are considered separately from the central government.

Jan 1, 1971

By H. J. Hager, P. H. Haskell

Fox the past 20 years Alabama has probably led all other coal-producing districts in the proportion of coal prepared by wet washing. All rail mines, with one exception, and a high percentage of truck mines now wash all coal under 3 or 4 in. Most of this coal has been cleaned by jigs, though within the past few years one or more wettable plants have been installed for cleaning some of the coal from practically all the major seams. These tables supplement either single or multicell jigs usually for one of the following purposes: (I) to wash the finer sizes of raw coal, (2) to rewash the finer sizes of washed coal after they leave the jigs, (3) to retreat jig middling products. The main purpose of this paper is to present cleaning data and operating factors involved in the preparation by tables of the finer sizes of raw coal. The specific information and data pertain to the Mary Lee seam of coal as extracted at three of the mines of the Alabama By-Products Corporation, which produces coal for both by-product coke-oven consumption and the general steam market. The Mary Lee seam has long been recognized by coal-preparation authorities as presenting a very difficult ash-reduction problem. Washing characteristics and physical structure of the seam vary widely. Its thickness ranges from 32 in. with no rock parting to l00 in. with from one to three partings. Over the entire field the bed contains bands of bone and rash. These are distributed throughout the seam cross section. A portion of this bone or bony coal occurs as definite bands 1 in. or more thick; however, some bone is interlocked as layers within the coal and consequently breaks into flakes when the coal is broken. This material is relatively high in ash and its specific gravity varies widely. It has been observed that in most cases in the washing of Mary Lee coal from 10 to 18 per cent of the raw coal is within ±0.10 specific gravity of the attempted point of separation. Therefore with the average wet jig, only with extreme difficulty can a low-ash product be obtained without loss of much marketable coal in the refuse. Without entering into the controversial question as to whether modern washing equipment can efficiently handle simultaneously all sizes up to a given maximum, suffice it to state that the comparatively old-type jigs in service at the Alabama By-Products Corporation's mines could not clean the fine sizes satisfactorily. Therefore, in 1931 that company installed six diagonal-deck tables at the Barney mine, which were installed as an addition to a complete plant cleaning all coal below minus 3 in. The primary washed product is shipped as steam coal and another portion may be prepared as washed nut for domestic trade. These tables are washing 9 tons per hour of raw coal sized to ¼ in. to 0. The washed table coal is mixed with the 3 to ¼ -in. jig product to constitute a 3 in. to o steam coal.

Jan 1, 1941

By John J. Sammarco

This report (System Safety Guidance 5.1) is the sixth in a nine-part series of recommendations and guidance addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various lifecycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction (Part 1).—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing system/software safety program. • 2.1 System Safety (Part 2) and 2.2 Software Safety (Part 3).—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g]and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File (Part 4).—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment (Part 5).—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. The guidance reports comprise parts 6 through 9 of the series and are listed below: [< 5.1 System Safety Guidance (Part 6).—This guidance supplements 2.1 System Safety. < 5.2 Software Safety Guidance (Part 7).—This guidance supplements 2.2 Software Safety. < 6.0 Safety File Guidance (Part 8).—This guidance supplements 3.0 Safety File. < 7.0 Independent Functional Safety Assessment Guidance (Part 9).—This guidance supplements 4.0 Independent Functional Safety Assessment.] [ ]

Jan 8, 2005

By Alfred Traverse

The Brandon lignite is a small deposit of very low rank coal near the village of Forestdale in the town of Brandon, Vt. It occurs in association with other sediments, principally sands and silts. This lignitic coal has attracted considerable scientific interest since the middle of the 19th century because of the abundance of fossils in the sediment and the rarity of lignite in New England. A cooperative investigation has been developed by E. S. Barghoorn, W. Spackman, and the author in which different phases of the problem have been worked on in a coordinated research program. This paper presents results of an investigation of the very abundant fossil pollen and spores and some other microfossils of the deposit. The studies on which this manuscript is based were made in large part at Harvard University in partial fulfillment of the requirements for a Ph. D. degree.

Jan 1, 1955

When the Organic Act of 1910 established the Bureau of Mines within the Department of the Interior, the Bureau&apos;s programs involved only health and safety research and education, and fuels testing. As the Federal Government&apos;s primary agency for research in minerals, the Bureau has expanded its scientific and technological investigations to mining, processing minerals substances, eliminating occupational health and safety hazards in the mineral industries, economic development, and resource conservation. Today, Bureau activities cover a broad spectrum of programs for meeting the diverse (and sometimes conflicting) needs of mineral industries, government, and the public. In the 1960&apos;s, the Bureau initiated programs to resolve environmental problems associated with past mining and mineral processing. In the 1970&apos;s, the energy crisis raised the national consciousness concerning our limited supplies of domestic mineral and fuel resources. Dependence on foreign sources of raw materials critical to our national economy and competition from other countries for these world supplies stimulated the need to conserve and use with intelligence the Nation&apos;s minerals, metals, and fuels.

Jan 1, 1976

Dr. Willett. I will start by answering one or two general points which have been posed. The first point is a question of liability of a seam to spontaneous combustion. Some seams are very liable to spontaneous combustion. Some seams are not liable at all except in most abnormal circumstances, and some seams have a liability somewhere between these two extremes. Dr. J. S. Haldane made the comment some 50 years or so ago that if you try hard enough you can make any coal seam in the world fire spontaneously. Many heatings have in fact occurred because the coal has been allowed to be ground up into a fine state and there has been air leakage through it for many years. This has resulted in spontaneous combustion which would not have occurred in some seams unless conditions had been very abnormal indeed. One comment I heard while listening to the discussions of one team was the importance of encouraging morale and the team seemed to go to the extent of suggesting that this was more important than the actual technical action taken. Though I agree that everything possible should be done to encourage morale, it must be in conjunction with the correct technical method of dealing with the Emergency.

Jan 1, 1973

By David Baker

In a paper presented to the American Institute of Mining Engineers, September, 1904, entitled uImprovements in the Mechanical Charging of the Modern Blast-Furnace,"&apos; I showed the great fault of mechanical charging-devices to be that the materials charged by the dumping of the skip were separated, the coarse materials having high velocity, and the fine, low— thus giving paths of low resistance through the stock in the furnace, which resulted in unequal distribution of the furnace-gases, unequal reduction, slips, scaffolds, irregular cutting of the inwall, "of" iron, and increased fuel-consumption. I showed how this could be prevented by rotary distribution, through which the irregular distribution in one layer charged is compensated by charging the subsequent layers from succeesively varied positions of the charger, and becomes practically eliminated when the angle between two successive positions is a little more or less than an even fraction of a full circle. Of all the devices then on the market, the nearest approach to the ideal arrangement was found in the Brown distributor, a full description of which was given. The one defect pointed out, however, was the difficulty of maintaining so much mechanism on the top of a blast-furnace. Since the presentation of that paper, I have designed a very

Jan 1, 1907

The following is a &apos;partial list of members and guests who called at Institute headquarters during the period Oct. 10, 1917, to Nov. 10, 1917. Edwin T. Blake, Berkeley, Cal. Alfred C. Lane, Tufts College, Mass. H. M. Boylston, Cambridge, Mass. W. G. Matteson, Houston, Texas. W. B. Cogswell, Syracuse, N. Y. E. Francis M&apos;Crossin, Birmingham, Ala. Paul R. Cook, Zaruma, Ecuador. R. E. Murray, Butte, Mont. F. W. DeWolf, Washington, D. C. Edmund Newton, Minneapolis, Minn. A. Faison Dixon, Venezuela. J. J. Ormsbee, El Paso, Texas. W. H. Dufur,, Oil City, Pa. Pablo Ortega, Havana, Cuba. Maxwell E. Erdofy, Lieut. Engr. Officers&apos;. W. E. Pomeroy, El Paso, Texas Reserve Corps, New York. J. C. Ralston, Spokane, Wash. Evan Fraser-Campbell, Scotland. W. L. Remick, Chrome, N. J. David B. Gemmill, Crown King, Ariz. Howard D. Smith, San Francisco, Cal. F. Lynwood Garrison, Philadelphia, Pa. Harold C. E. Spence, Steeple Rock, N. M. C. J. Hall, Spassky, Siberia. R. K. Stockwell, Salt Lake City, Utah. H. Hamada, Tokyo, Japan. Maurice W. Summerhayes, Timmins, Rush M. Hess, Bouse, Ariz. Ont., Canada. A. Howard Higgin, London, England Malcolm M. Thompson, Morsemere; N. J. A. O. Ihlseng, Joplin, Mo. Nicholas Truschkoff, Petrograd, Russia. T. Ishikawa, Japan. H. J. Wendler, Los Angeles, Cal. C. H. James, Tucson, Ariz. Ira T. Wright, Hurley, N. M. R. R. Landon, Philippine Islands. C. Yabe, Japan. Robert W. Bissell has now become associated with Gunn, Richards & Co., of New York, N. Y. Major Reginald W. Brock is giving a course in a school for commanding officers in England.

Jan 12, 1917

By R. Mensah-Biney, M. T. Hepworth, K. J. Reid

The kinetics of gold-bromide loading onto activated carbon was investigated in a batch stirred reactor. Based on a second-order equation, the amount of gold adsorbed by the carbon was correlated with time. From a 30ºC solution containing 25 ppm Au and 0.8 g/L carbon, the rate constant for gold-bromide species onto activated carbon ranged from 0.27 x 10-3 to 1.2 x 10-3 (kg/t)-1 min-1. The equilibrium saturation capacity (Qe) was 36 ±3.0 kg/t from the same system. The rate of loading increased with increasing temperature and decreasing particle size, pH and solution gold concentration. The calculated activation energy (Ea) was 8.8 kcal/mole, significantly higher than those reported for physical adsorption. The equilibrium saturation capacity (Qe) increased with increasing concentration of gold in solution but was independent of other variables such as temperature, agitation speed, particle size and pH. These rate constants and equilibrium saturation capacity for the gold-bromide species are higher than those reported for the gold-cyanide systems.

Jan 1, 1998

By W. I. Nissen

As part of its program to provide technology for reducing undesirable environmental impacts of mineral processing operations, the Bureau of Mines developed the citrate process for desulfurizing industrial stack gases that contain from 0.1 to 2 vol pet S02. In this regenerable flue gas desulfurization (FGD) process, S02 is absorbed from cleaned and cooled industrial flue gas with a citric acid-sodium citrate solution. The absorbed S02 is subsequently reacted with H2S to precipitate marketable elemental sulfur and regenerate the solution for recycle. Laboratory investigations of process parameters provided information for designing larger scale continuous operations. Information gathered from operation of two pilot plants, one at a copper smelter and one at a lead smelter, confirmed the laboratory results. Data were obtained for design and construction of a commercial-sized demonstration plant at the George F. Weaton Power Station, Monaca, PA. A preliminary operation of the plant was demonstrated, under a cost-sharing Bureau-industry contract. This bulletin describes the citrate process and gives results of the laboratory, pilot plant, and demonstration plant studies, as well as corrosion investigations.

Jan 1, 1985

By Congcong Chen, Bo Ma

When assessing the safety of a tailings dam, the constant weight method (CWM) is one of the most commonly used methods. However, when the evaluation indicator value suggests serious defects, the evaluation value is often inconsistent with the actual situation. To address this issue, the variable weight method (VWM) is introduced to assess the safety of the tailings dam. Initially, a three-layer indicator system for dam failure safety assessment is built, and individual indicator values are divided into four grades. Then, an appropriate state variable weight function is constructed and relevant parameters are determined. Finally, a case study is illustrated to verify the effectiveness of the model. The assessment results of the VWM more closely represent the actual situation than that of the CWM, which is more helpful for decision makers and technicians to take scientific and reasonable precautionary measures, thereby improving the safety management of the tailings pond.

Oct 8, 2022

By Rudá Grossi Coimbra Martins

A estruturação organizacional da gestão da informação em Central de Serviços já está consolidada no ambiente de Tecnologia da Informação. O ambiente de Tecnologia de Automação compartilha características semelhantes, já que também fornece serviços para seus clientes. Entretanto, serviços de automação possuem particularidades derivadas, em grande parte, do fato de que são mais críticos para a atividade fim da empresa, já que visam manter a operação. Implantar uma Central de Serviços em ambiente de Tecnologia de Automação de uma empresa já existente demanda uma série de modificações em termos de Tecnologias, Processos e Pessoas para trazer os retornos desejados em termos de gerenciamento, organização da rotina e disponibilidade dos ativos. Este trabalho apresenta alternativas para atuar sobre os três componentes supracitados durante a implantação de uma Central de Serviços, com foco em sua operação através de uma Gestão Compartilhada (Cosourcing). Experiências adquiridas em projetos de especificação e operação de Central de Serviços também são apresentadas para embasar a estruturação da gestão da informação em ambiente de Tecnologia da Automação de indústrias de Metais e Mineração.

Jul 30, 2018

By Thomas G. Chapman

The four major steps in the production of marketable copper are mining, concentrating, smelting, and refining. In a few cases, however, leaching takes the place of concentrating, smelting, and refining, and in others ores are smelted without being concentrated. Copper ores have been milled since the early days of mining in the United States. Except in the Michigan district, most copper ores went direct to the smelter until the so-called porphyry mines were developed. At present, although considerable leaching and direct-smelting ores are produced, the bulk of the copper ore mined is concentrated. Improved methods of concentration have kept pace with the increased tonnages of ores milled.

Jan 1, 1936