Search Documents

By CORA ROELOFS

In the USA, miners are at higher risk for work-related disorders that could precipitate an opioid prescription, injury-related opioid prescriptions, and opioid overdose. We aimed to support prevention of these outcomes with an “opioid hazard awareness” miner safety training module. In January and February 2020, the training module was embedded within required mining safety and health training for stone, sand, and gravel miners in Massachusetts (USA). Training impact and reception were assessed with a pre- and post-training survey of trainee characteristics, training content knowledge, and attitudes. Over 800 miners were trained and over 600 responded to surveys. We found statistically significant improvements in opioid risk factor knowledge and knowledge of resources to help a coworker. Nonstigmatizing attitudes were high both at baseline and following the training. The training was perceived as relevant and useful by trainees. Improving opioid hazard awareness in high-risk worker populations has potential to reduce opioid dependence and downstream impacts including overdose death. Employer injury-prevention efforts should be reinforced while worker health and safety training enhances awareness of opioid-related harms and prevention strategies for miners and other high-risk worker populations.

Nov 19, 2021

By C. T. Young, J. L. Lytton

In recent investigations,1,2 the strength and thermal stability of dislocation substructures prepared by 5 to 25 pct room temperature tensile straining and recovery annealing at 120°, 160°, and 200°C have been studied in randomly oriented polycrystalline high purity aluminum. The techniques of transmission electron microscopy revealed that a major source of the strength and stability of dislocation substructures was the formation, during room temperature straining, of well-defined cells bounded by dislocation tangles which rearranged into nearly perfect dislocation networks during recovery, forming the boundaries of subgrains. The strength of such substructures increases with decreasing cell or subgrain size,2"6 and the formation of fine subgrain structures can provide thermally metastable strength at low temperatures and can favorably alter the course of primary creep at elevated temperatures.7'8 For maximum benefit, however, sub-grain growth should be reduced or eliminated. It was, therefore, decided to investigate the use of heterogeneous precipitation on dislocation networks as a means of imparting increased strength and thermal stability to subgrain structures through effective pinning. C.T. YOUNG, STUDENT MEMBER AIME, and J. L. LYTTON, Member

Jan 1, 1970

By R. E. Wagner

MISSOURI's famous lead area, in what is known as Southeast Missouri, is locally termed the "Lead Belt." These deposits are in the Bonne Terre dolomite of late Cambrian age which has a thickness of nearly 400 ft. Underlying this is the La Motte sandstone which varies in thickness from 0 to 400 ft. The La Motte beds are deposited directly on the ancient erosion surface of Pre-Cambrian porphyries and granites of probably Algonkian age. The buried igneous peaks extend up into the Bonne Terre in several areas within the Lead Belt. Overlying the Bonne Terre are shales and siliceous dolomites of late Cambrian and early Ordovician age. Within the Lead Belt these have a thickness of from 0 to 500 ft. The district is bounded in general on the southwest by the Sims Mountain fault, on the northwest and north by the Big River fault, and on the

Jan 1, 1947

By V. E. Edlund

Laboratory batch flotation tests were conducted on copper converter slags to evaluate the relative merits of recovering copper from slow-cooled versus water-quenched slags. Three slags containing 1.6, 5.0, and 6.6 percent copper were used. More than 90 percent of the copper was recovered in a rougher concentrate leaving a 0.2- to 0.3-percent copper tailings when treating slow-cooled slag. Lower recoveries and higher copper tailings ranging from 0,5 to 0.6 percent copper were obtained from quenched slag. Grindability studies were made on the respective heat-treated slags. Quenched slags proved more difficult to grind than slow-cooled slags. Cost studies showed that (1) the cost of slow cooling and crushing off-sets any advantages of higher copper recoveries from slow-cooled slag, and (2) water-quenched slag, which requires no crushing preparatory to grinding, could be treated more economically. Costs based on processing 1,000 tons of slag per day would be $1.85 per ton for quenched slag versus $2.37 per ton for slow-cooled slag.

Jan 1, 1971

By Chang Wei, Zhigan Deng, Minting Li, Cunxiong Li, Gang Fan, Xingbin Li

Molybdenum and nickel in black shale ore exists as amorphous sulfides which has highly active, and easily oxide to sulfuric acid and sulfate at low temperature in the presence of excess oxygen. Take advantage of the characteristic to leach molybdenum and nickel from black shale. Oxidation, conversion and dissolution behavior of amorphous colloidal molybdenum and nickel sulfide in pressure leaching process was studied. The effects of stirring speed, temperature, concentration of sulphuric acid, oxygen process and mineral granularity on molybdenum and nickel leaching were investigated. The results showed that dissolution rate increased with increasing temperature and stirring speed, but decreased with increasing concentration of sulphuric acid. And dissolution of molybdenum and nickel from ore only need oxygen without any other reagent.

Mar 1, 2017

By L. Heber Cole

In making this plea for a better and more sympathetic understanding of the non-metallic industry, I do not for one minute wish to give the impression that I in any way belittle the wonderful strides that have been made in the exploitation of our metallics. We in Canada can be justly proud of our Sudburys, Norandas, Flin Fions, and of the remarkable growth of the Consolidated in British Columbia, and at the same time, without in the !east detracting from these worthy undertakings, be equally as proud of our asbestos, gypsum, salt, and coal deposits, as well as of our building-stone and limestone industries. If, in my remarks, I have occasion to compare the metallic with the non-metallic industry, I do so, not with any idea of dimming the glory which the metallics of Canada have gained- not only in our own country, but in the world at large-but for the purpose? of bringing to your attention the fact, perhaps not very well recognized, that Canada contains deposits of non-metallics well worth y of your serious consideration. In the past 33 years, namely, since 1895, the value of non-metallics produced in Canada has exceeded the value of metallics in 19 of the years, and for the last three years has been increasing rapidly. The war years (1915-1918 inclusive) naturally saw an intensive metallic production, but since that time, with the exception of 1925, when there was a general depression throughout the whole country, the non-metallics have been in the ascendency.

Jan 1, 1929

By S Das

Deposit-10/11A is situated in the iron rich Bailadila region of India comprising haematite ore of average grade 65 per cent Fe. The deposit production line was commissioned in the year 2002 having a capacity of 5 Mt/a. The plant has the state of the art mineral processing equipments.The ore is transported from mines to crushing plant by means of dumpers. The ore is comminuted in two stages to get 150 mm top size product and this product is transported through conveyor system and is stored in silos as feed stock for beneficiation plant. In the beneficiation plant this crushed product is wet screened in two stages to produce a product of lump (-150 + 10 mm) and fines (-10 + 3.15 mm). The product of -3.15 mm top size is fed to primary classifier for a size separation at 150 µm. The resultant product (-3.15 mm + 150 µm) is dewatered and transported to fi ne ore product stock yard through conveyor system. The minus 150 µm material from classifier overflow is fed to cyclones (508 mm cyclone battery with an apex of 65 mm) for desliming at 45 µm and to recover ultrafi nes (-150 + 45 µm). The cyclone overfl ow slimes (-45 µm) along with water is treated in lamella thickeners to recover process water. The thickener underflow material is transported to tailing pond (discharge rate is 300 m3/h at a specific gravity of 1.4) by pumping through HDPE (high density poly ethylene) pipeline and the over flow water is being recirculated. The water requirement for beneficiation is approx 1.5 m3 per ton of ore.This paper aims at identifying and quantifying the factors that affect the overall plant performance (grade and recovery) during the different seasonal variations especially in the rainy season (mid-June to end October). The effect of seasonal variations on unit operations such as milling, classification, thickening and filtration are discussed. Specific cases are presented as examples and recommendations are formulated.

Jul 11, 2011

Not many accounts of mining methods or labor conditions in the mines in early days can be found; all that have seemed to be authentic have been included in the preceding chapters. In practically every field opened before 18.10 the first coal was recovered by quarrying, or strip mining, the operations, of course, being by hand and on a very small scale; new places were opened as soon as mining became difficult or expensive. Where it became necessary to drift into the hillsides, the first coal was taken out by sleds, and later by small wagons, the power being supplied by the miner, often assisted by dogs. Wooden rails then came into use with small cars running on them. These cars were very small, usually holding only a few bushels; in the Belleville, Illinois field as late as 1863 cars having capacities of 10, 12, 14 and some as large as 30 bushels were in use. It was not until late in the 1830's that horses or mules came into use for haulage purposes in the Pittsburgh region, although some had been used in the Richmond, Virginia field at an earlier date. Coal was usually undercut by hand and wedged down, until explosives came into general use, and in nearly every field the coal was forked into the cars, the fine coal, or slack, being left in the mine. Hours worked were very long, but few records remain to show what they were at different places and times; there was undoubtedly a great variation between districts and mines. Roy stated a miner could often produce 5 or 6 tons in a day of 8 or 9 hours in a 5 or 6 foot seam, but in another seam possibly could mine only 3 1/2 to 4 tons. He estimated an average day's work in a four foot seam at about 3 1/2 tons.1 In a strike in the Belleville field in 1863 it was found that an average skilled miner in the field could probably produce 4 to 5 tons a day.2 This was only the coarse coal loaded and did not include slack. In 1873, a coal undercutting machine was tried at a mine about two miles from Brazil, Indiana, said to be the first coal machine ever invented in the United States. It was run by a 5 H.P. steam engine (later to be changed to compressed air), and consisted of an iron rim, four feet in diameter with movable steel teeth placed about one foot apart. The rim

Jan 1, 1942

By D. Das, B. K. Nandi

The present study focuses on utilising the electrocoagulation (EC) process for the treatment of process water generated in an iron ore beneficiation plant for safe discharge and reuse. Removal of heavy metals like Fe, Cr, Cu, Zn, Mn and Pb which was found in higher concentration along with some other impurities exceeding the permissible and discharge limit were attempted. The influence of different electrode material, current density, inter-electrode distance, and solution conductivity was explored for effective removal of the metal ions. Experimental results infer that almost 99.95% Fe, 97.77% Cr, 73.44% Cu, 99.34% Pb and 88.69% Mn was removed using aluminum electrodes at monopolar mode at a current density of 68.50 A/m2, inter-electrode distance of 1 cm and solution conductivity of 1.033mS after 60 min of EC. In addition, removal of other toxins like TDS, turbidity, salinity and conductivity etc. was also assessed during the process. Removal of such heavy metal ions by EC was found to follow 1st order kinetics with electric energy consumption of 3.93 kWh/m3, electrode consumption of 0.1191 kg/m3 and operating cost of 0.6115 US$/m3 respectively. Keywords: Fe removal, electrocoagulation, Al electrode, turbidity

Jan 1, 2020

By T. W. Beck

Roof bolter occupations in underground coal mines continue to experience overexposure to respirable dust. One potential source of dust in roof bolting operations is the exhaust from the roof bolter dust collection system. A wet exhaust conditioner (water box) has been developed to reduce dust emissions from the exhaust of the vacuum dust collection system on roof bolting machines. The exhaust conditioner consists of a muffler chamber and a water chamber with four internal partitions to direct airflow over the surface of the water. The National Institute for Occupational Safety and Health conducted a series of laboratory tests to assess the respirable dust capture ability of this device as compared to the standard exhaust muffler. To determine the dust collection efficiency, both devices were placed in the exhaust stream of a simulated roof bolter dust collection system. Gravimetric samplers were operated upstream and downstream of the exhaust conditioner and muffler to evaluate the ability to capture both respirable coal and limestone dust. Researchers observed a 41 % reduction in dust concentrations for the water exhaust conditioner in the laboratory configuration. Significant levels of dust deposition in the sampling chambers may have contributed to this effective capture rate.

Jan 1, 2012

By Frank C. Townsend

Waste disposal schemes using spent shale in embankments require a thorough knowledge of its geotechnical engineering properties for environ-mentally safe disposal. In this context, the objective of this laboratory investigation was to determine the physical properties, geotechnical properties, and composition of spent oil shale retorted by the PARAHO and TOSCO processes. Physical properties consisted of mechanical analyses, Atterberg limits, and specific gravity determinations. Geotechnical engineering properties were determined by compaction, maximum-minimum density, unconfined compression, triaxial compression, permeability, direct shear, Ko, cyclic tri-axial, resonant column, and Los Angeles Abrasion tests. Petrographic, chemical, and scanning electron microscopy analyses were used to determine compositional features. Unprocessed shale is hard and durable and more properly described as a carbonate rock instead of shale. PARAHO is classified as a GP, while TOSCO classifies as an SM. PARAHO requires no moisture for compaction to maximum densities; however, TOSCO does. Retorting causes a loss in durability but creates self-cementing characteristics, which for PARAHO a 3-to 8-fold strength increase was observed, while for TOSCO the increase was 1.5 to 3 folds. The shear strength, compressibility, and dynamic properties of compacted PARAHO are comparable to those for sandy gravels. Compacted PARAHO is semipervious, while compacted TOSCO can be semipervious to impermeable.

Jan 1, 1979

By D. Harrington

As no cure is known for silicocis after it has developed, prevention is the only effective remedy. There are two main lines of approach to the problem of dust-disease prevention in industry - the engineering, through control of dust production, and the medical, through selection of workers by examination; success probably depends upon a combination of the two. Hatch (146) considers the following measures essential to a complete, well-balanced program of control of the dust hazard in industry: 1. Selection of workers by means of physical examinations in order especially to eliminate those with tuberculosis and other disorders of the respiratory system. 2. Reduction of the duct concentration below the standard of permissible dustiness through adequate moans of dust control and good housekeeping. 3. Limiting the frequency and duration of employment in the dusty occupations, thus reducing the rate of deposition of dust in the lungs. 4. Routine measurement of the effectiveness of the dust-control program by means of periodic medical examinations and duct surveys.

Jan 1, 1935

By J. Paces, E. Miller, K. L. Komarek

The resistivity was determined as a function of temperature over the composition range from pure cadmium to 40 at. pct Cd. Melts with cadmium contents less than 85 at. pct had negative temperature coefficients of resistinity. On cooling below a transition temperature close to the liquidus temperature, the slope of the resistivity-temperature curve changed sharply. The activation energy calculated from the slope was 0.07 ev above the transition temperature and 0.14 ev below. The resistivity vs composition curve shows two maxima corresponding in composition approximately to CdSb and Cd3Sb2. THE relationship between the structure of a liquid and that of the crystal formed on solidification is at present not well-under stood. Various experimental determinations of the properties of liquids indicate that deviations from random atomic arrangements in liquids occur and that the properties of a solid and of its melt are closely related. Thermody-namic activities of liquids usually show negative deviations in systems where compound formation occurs in the solid,' and X-ray data indicate that close-packed solids and their melts frequently have nearly the same coordination number. Electrical resistivities and viscosities of liquids frequently exhibit maxima at compositions corresponding to compounds in the solid state. It should be of interest to study systems which have both stable and metastable compounds in the solid, and to determine if the short-range order in the liquid is affected by the existence of the metastable solid phase. The Cd-Sb system exhibits such a metastable phase. The phase diagram is shown in Fig. 1.3 The stable system has one intermetallic compound, CdSb, crystallizing in the orthorhombic crystal structure, with a melting point of 456°C. The metastable system also has one compound, Cd3Sb2, melting at 420°C and crystallizing in the monoclinic structure. Metastable alloys transform to the stable crystal structure in the temperature range from 250o to 350°C. Several distinct indications of very strong short-range order in the liquid phase have been reported in this system, with a close relation between the ordering in the liquid and the existence of both the stable and metastable solid phases. Scheil and Baach4 have observed distinctly different vapor pressures for liquid Cd-Sb alloys depending on whether the liquid solidified to the metastable- or stable-phase configuration. They observed an unusually sharp increase of the activity in a limited temperature interval immediately above the liquidus temperature of stable alloys, followed by a sudden decrease in slope to what they considered normal values. On cooling, the activity data reproduced the values in the normal range but then deviated from the values obtained on heating. They also observed that specimens of the stable phase upon melting and resolidifying always crystallized in the stable crystal structure as long as the melt was not heated to more than 485° to 525°C; otherwise solidification to the metastable phase occurred. However, in a later investigation, these results were not reproduced (13). The resistivity of liquid Cd-Sb alloys has been investigated by Matuyama 5, Oleari and Fioram, 8 and Belaschenko (141, but only above 500°C, the temperature region where Scheil and Baach observed no vapor-pressure anomalies. The data of Matuyama and of Oleari and Fiorani are reproduced in Fig. 5 and show a maximum in resistivity at 50 at. pct Cd. The data of Oleari and Fiorani, however, show the maximum as being rounded, and their values in general are slightly higher than those of Matuyama.

Jan 1, 1964

THE paper on "Specific Efficiency of the Blast Furnace" by Richard Franchot, which was pub-lished in the September issue of MINING AND METALLURGY, was presented for discussion at the Pitts-burgh meeting. The session opened with a discussion among S. P. Kinney, Mr. Franchot, and J. N. Reese as to the methods and results in sampling for cyanides in the blast furnace. This is covered in detail in writ-ten discussion below. T. T. Read objected to the use of the term specific efficiency as likely to be confusing. The blast furnace has to perform the function of reducing Fe, 03 to Fe as well as that of fusing the metal and, since the reduc-tion of Fe, 0? involves a CO equilibrium, it seems mis-leading to calculate efficiency on the basis of burning the , all carbon to CO? since it is not possible. Mr. Franchot replied that he used the term in the sense defined by Richards in his "Metallurgical Calculations;" but a subsequent search failed to reveal the term in Richards, who says (page 245, 1st edition): The practical conclusion is that a blast furnace generates in itself not much over 40 per cent of the calorific power of the fuel used, and rejects nearly 60 per cent; by using part of the waste gases to heat the blast, however, some of this rejected heat, to an amount representing net 5 to 10 per cent of the calorific power of the fuel used, is returned to and injected bodily into the furnace, thus rendering available for the purpose of running the furnace about 50 per cent of the calorific power of the fuel as a maximum. The efficiency with which the furnace applies this 50 per cent usefully to the objects of the reducing and smelting is another question for investigation.

Jan 2, 1927

By Sowmiyaa. V. S., Tiruvengala Padma

Axial compression capacities of bored cast in situ piles as per Indian and International Standards are compared in this paper. Bored cast in-situ piles resting on soil and rock are considered for capacity assessment comparison. The standards considered for comparison are Indian Standards namely IS 2911-Part 1-Sec 2:2010 and IRC 78, International Standards like AASHTO LRFD Design-2017, API 2A WSD, BS 8004:2015 & EN 1997: Part 1:2014. The end bearing mobilization limits as proposed by various standards and their influence on longer piles in cohesive and cohesionless soils are discussed.

Sep 1, 2022

By John V. Beall

There was optimism on 14th Street on April 22, Earth Day. We only have the report second hand because the demonstration conflicted with another appointment. Fifth Avenue was closed to vehicular traffic from 14th Street to the Park for a few hours and the crowd that showed up to promenade rivaled anything that can be imagined, even one at a country fair in Merry Old England. Certainly the domestic animals were there and the costumes were wild-as they are almost any day on 5th Avenue. However, the mood was friendly, happy and optimistic according to one of our neighbors who filmed and taped interviews with some of the characters. People think the air is going to be clean, and the water pure in the future. Land is going to be treated with respect. Even if the demonstration temporarily fouled the streets with litter, it served the purpose of dramatizing awareness. In talking to our friend about his experiences we didn't miss the opportunity to sound out his impression of whether or not people recognize that no group of people nor industry has a monopoly on pollution.

Jan 1, 1970

By Carl-Henrik Knudsen, Rolf Tore Arnesen, Eigil R. Iversen

Recovery of iron and copper from acid mine drainage was studied in pilot scale at a continuous treatment plant at the mine site of the King's mine in Roeros, Norway. The average load on the plant was 1 m3/h. The process tested in this project is a three-step process consisting of: 1) Fe(OH)3 precipitation at pH 3.5, dewatering of iron sludge and transport to ferric chloride plant; 2) after filtration precipitation of residual metals at pH 9, concentration of metal sludge by flotation; 3) extraction of metals from the sludge with sulphuric acid followed by recovery of copper by electrolysis. The copper could be used for local production of different crafts, but this condition needs a further evaluation. The process economy at a full scale plant is evaluated.

Jan 1, 2000

By T. Gouri Charan

Indian coals, which are of Gondwana origin, contain high amounts of mineral matter, wherein the extraneous material was intimately mixed in the coal matrix during the formation stage, causing a high level of impurity in the run-of-mine (ROM) material. These coals possess difficult to very difficult washability characteristics. Beneficiation of high-ash non-coking coals of India has become the prerequisite for improving the overall economics and efficiency of power generation. The use of dry cleaning systems in India for beneficiation of non-coking coals has gaining renewed interest recently. The benefit of the dry beneficiation process is to exploit the given resources while providing a more reliable and consistent quality fuel with a low operating cost. M/S Allmineral has introduced a technique for the dry beneficiation of coal, which is being tried in India for the treatment of high-ash non-coking coals. The first commercial air jig of 50 t/hr capacity was installed and commissioned to beneficiate high-ash coals of 40 x 5 mm feed with an ash content of 40%; a clean coal product of 33% ash was produced and is being used for a sponge iron plant.

Jan 1, 2011

By Xudong Liu, Feng Chen, Yufeng Guo, Wei Chen, Tao Jiang

Willemite is typically found in oxidized zinc ores and metallurgical secondary resources but without effective extraction method yet. Based on the ideas of zinc phase reconstruction in the willemite, the extraction of zinc from willemite by calcified-roasting using CaO as additive and ammonia-leaching process was studied in this paper. The influences of CaO dosage, roasting temperature, roasting time on the phase transformation and zinc leaching rate were studied, which were characterized by XRD. The results indicated that Zn2SiO4 was transformed into ZnO or Zn2CaSi2O7 .After roasted with 1.4 times of theoretical CaO dosage at l280 for 40 minutes, willemite was thoroughly transformed into ZnO. The zinc leaching rate of the roasted sample was 97.45% in NH4Cl-NH3 H2O leaching system, which increased by 91.40 % compared with zinc leaching rate of 6.05% when willemite was directly leached in NH4Cl-NH3 H2O system.

Jan 1, 2016

By Robert C. Johnson

Domestic byproduct fluorine (in fluosilicic acid) availability at various price levels of aluminum fluoride were determined and a contingency availability curve developed. The supply of byproduct fluosilicic acid is restricted in amount to certain geographic regions, where plants processing phosphate rock are located, and the byproduct can be collected. The maximum possible U.S. annual supply, based on potential plant capacities, is 373,400 tons of fluosilicic acid containing 295,400 tons of fluorine. Based on inputs of 5, la, 25, 50, and 100 thousand tons per year, five levels of producing aluminum fluoride from fluosilicic acid (100 percent) were costed. Based on a 12-percent discounted cash flow rate, including the cost of salvaging the fluosilicic acid, the calculated selling price of aluminum fluoride ranged from $233 per ton to $448 per ton. At the higher price, 98 percent of the potential supply of byproduct fluosilicic acid could be used profitably; at the lower price only 46 percent could be used profitably.

Jan 1, 1973