Search Documents

By J. B. Mackintosh

In a recent paper read before the Institute on this subject, Mr. G. C. Stone advances the theory that the precipitate obtained in Williams's volumetric process,* by treating the boiling nitric acid solution of a manganese salt with potassic chlorate., is not pure MnO2, but approximates more closely to the composition 10Mn02+Mn0. As the value of the process and the accuracy of our results mould depend on whether this was the fact or not, it has seemed to me, and to my associates, Messrs. Beebe and Colly, that it would be of importance to ascertain the composition of this precipitate, and to that end the following series of experiments has been undertaken. These experiments have all been based on the considerations: 1. That potassic permanganate has an oxidizing power equivalent to five atoms of oxygen for every two of manganese : K2Mn2O8 = K2O.2MnO.O5. 2. That the same amount of manganese in the state of binoxide has an oxidizing power equivalent to two atoms of oxygen : 2MnO2 = 2MnO.O2. If, then, we take a solution of permanganate of unknown strength, and reduce it to binoxide, the oxidizing power of the binoxide formed will be equal to that of two-fifths the quantity of the permanganate solution originally taken. While, if the precipitate obtained should not be binoxide, but an indefinite or definite mixture of bin- and mon- oxides, then, from its equivalent oxidizing power, we can calculate its composition. The analyses were conducted in the following manner. The amount of permanganate taken was decomposed with hydrochloric acid, and concentrated to expel the excess of water. Sufficient excess of nitric acid was now added, and the solution was boiled until all the hydrochloric acid was destroyed. The manganese was then precipitated by potassic chlorate; and, after standing some time to cool—a pre-

Jan 1, 1884

By Ross A. Scarano

It wasn't until late 1976 that the U. S. Nuclear Regulatory Commission (NRC) set about to address the uranium tailings issue in earnest. It was decided that a generic environmental impact statement related to uranium milling operations would be prepared to support formal tailings regulation. We recognized, however, that this was a task that would take many years to complete and we could not take a "business as usual" approach to tailings management in the interim; the issue was too sensitive. To facilitate licensing during the interim period, the NRC developed guidelines in May 1977, for the industry in the form of the following performance objectives for tailings management: Siting and Design 1. Locate the tailings isolation area remote from people such that population exposures would be reduced to the maximum extent reasonably achievable. 2. Locate the tailings isolation area such that disruption and dispersion by natural forces is eliminated or reduced to the maximum extent reasonably achievable. 3. Design the isolation area such that seepage of toxic materials into the groundwater system would be eliminated or reduced to the maximum extent reasonably achievable. During Operations 4. Eliminate the blowing of tailings to unrestricted areas during normal operating conditions. Post Reclamation 5. Reduce direct gamma radiation from the impoundment area to essentially background. 6. Reduce the radon emanation rate from the impoundment area to about twice the emanation rate in the surrounding environs. 7. Eliminate the need for an ongoing monitoring and maintenance program following successful reclamation plan. 8. Provide surety arrangements to assure that sufficient funds are available to complete the full reclamation plan.

Jan 1, 1980

By L. L. McDaniel

ROLLER—As one who has been privileged to read Mr. Poland's paper before its publication, I wish to express high praise for it and the record which it gives of the work done by the Research and Development Department of Revere Copper and Brass Inc. in developing a satisfactory furnace for the recovery of metallic zinc from secondary metals by distillation. I have also had the opportunity of studying the operation of the furnace when running on scrap brass at the Detroit plant of Revere, and I can therefore say from knowledge gained first-hand that the unit is efficient and economical when used in conjunction with distillation. However, when I read what Mr. Poland has to say in reference to the possibility of using the furnace for melting copper cathodes for the production of oxygen-free and tough-pitch copper shapes, I am constrained to be somewhat skeptical. No doubt the furnace can readily be modified so as to make it possible to melt cathodes, but that is only a part of what is required to produce refinery shapes. Because of its construction the atmosphere in the furnace is highly reducing and even without protective gases such as nitrogen the copper cathodes which are

Jan 1, 1950

By F. F. Poland

S. ROLLE*—As one who has been privileged to read Mr. Poland's paper before its publication, I wish to express high praise for it and the record which it gives of the work done by the Research and Development Department of Revere Copper and Brass Inc. in developing a satisfactory furnace for the recovery of metallic zinc from secondary metals by distillation. I have also had the opportunity of studying the operation of the furnace when running on scrap brass at the Detroit plant of Revere, and I can therefore say from knowledge gained first-hand that the unit is efficient and economical when used in conjunction with distillation. However, when I read what Mr. Poland has to say in reference to the possibility of using the furnace for melting copper cathodes for the production of oxygen-free and tough-pitch copper shapes, I am constrained to be somewhat skeptical. No doubt the furnace can readily be modified so as to make it possible to melt cathodes, but that is only a part of what is required to produce refinery shapes. Because of its construction the atmosphere in the furnace is highly reducing and even without protective gases such as nitrogen the copper cathodes which are

Jan 1, 1950

By Frank E. Cash

The data in this circular were compiled so that individual phosphate companies might have the benefit of the experience of other phosphate companies, and that industries in general might compare experiences (taking into consideration relative hazards), thereby promoting accident preven¬tion. ACKNOWLEDGMENTS The descriptive matter is taken in part from a. paper by Cash and von Bernewitz.4/ Production figures ore from Mineral Resources of the United States;5/ accident data were furnished by each of the operating companies in the pebble-phosphate district, and their assistance in making this report possible is gratefully acknowledged.

Jan 1, 1936

By Satyajit Vaidya, Rudolph Frizzi, Quadri Owokoniran

"This paper presents a case history in the design and construction of high-capacity drilled shafts for the iconic New York Wheel presently being constructed along the St. George area waterfront in northern Staten Island, New York. Although the site is located in an area that offers views of the Statue of Liberty, the Manhattan skyline, and New York Harbor, the variable and challenging subsurface conditions at the site and the structural loading requirements for Wheel erection and service conditions presented geotechnical design and construction challenges. The paper focuses on site and subsurface conditions, drilled shaft design and construction details, results of Osterberg-cell and lateral load testing, and load test data analysis and evaluation.PROJECT DESCRIPTIONThe proposed 630-foot (190 m) -tall New York Wheel (the Wheel) is projected to be one of the tallest observation wheels in the world. Upon completion, the Wheel will be capable of carrying over 1,400 passengers in its 36 capsules. The Wheel site is located along New York Harbor offering views of the Statue of Liberty, the Manhattan skyline, and the New York Harbor; see Fig. 1. The Wheel structure is sited along the waterfront, and served by a 3-story terminal located south of the Wheel in the eastern portion of the site and having a footprint area of about 34,250 sq-ft (3,180 sq-m). A 4-story parking Garage, with a footprint of about 112,840 sq-ft (10,480 sqm), is to be constructed south of the Wheel in the central and western portions of the site.SITE AND SUBSURFACE CONDITIONSThe site’s close proximity to the New York Harbor presented geotechnical challenges because the site is located in an area that was once beyond the historic shoreline of Staten Island. The site is an about 350,000-sq-ft (32,500-sq-m) parcel generally bounded by the Richmond County Bank Ballpark to the southeast, the 9-11 Memorial to the east, Bank Street to the north and northeast, and Richmond Terrace and an associated retaining wall to the southwest and south. A 50-ft (15-m) -wide New York City Transit Easement, with an active on-grade service area and tracks, is located in the southern portion of the site. See Fig. 2 for site location and approximate location of the Wheel foundation footprint."

Jan 1, 2016

By Diego Benites

El presente texto señala los resultados de la caracterización mineralógica de 28 muestras con importante contenido en sulfosales de plomo y cobre de origen hidrotermal provenientes de la Sierra Central del Perú. El principal objetivo fue caracterizar la mineralogía de la zona con énfasis en las sulfosales y el aporte de plata que éstas podían contener. Así, las sulfosales identificadas por microscopia óptica en conjunto con microscopia electrónica de barrido son: tetraedrita, tennantita, boulangerita, bournonita, fizélyita, jamesonita, semseyita, zinkenita; entre otros. Para determinar qué minerales aportaban plata y en qué porcentaje, se realizaron estudios puntuales por microscopia electrónica. Así también se verificó que la plata se aprecia en pequeñas cantidades en sulfosales de plomo, mientras que éstas aparecen en mayor abundancia con respecto a las sulfosales de plata y de cobre.

Oct 21, 2015

The Third Session of the Forty-Sixth Meeting of the Rocky Mountain Coal Mining Institute convened at the Hotel Colorado, Glenwood Springs, Colorado, June' 20, 1950, at 9:30 a.m., G. E. Sorenson, President, presiding. PRESIDENT SORENSON: The meeting will come to order. To refresh your memory, I will read off the names of the people on the various committees. President Sorenson read off the names on the committees. Mr. Whiteside, do you wish to make an announcement? MR. WHITESIDE: Yes, I would like to 'say a word. .4s you know, this afternoon you will be on your own, and I think some would like to go to Rifle. I wonder if we could get a vote on that now as to how many would like to go to Rifle, as they at Rifle would like to know so they can provide conveyances. There seems to be about 14 or 16 that would like to go to Rifle.

Jan 1, 1950

By S. P. Mehrotra, P. C. Kapur

A phase-species classification is suggested for the mathematical models of flotation kinetics. Important models are discussed and the structure of their rate constants and parameters is analyzed. Split or enhancement factors are formulated for different kinetic models. The steady state dynamics of the flotation circuits can always be described in terms of these factors. For simulation of circuits, feed is characterized in a formal manner starting from a multivariate distribution of particles in flotation rate, size and mineral content. Synthesis of optimum circuits which simultaneously searches for the best process variables and structural parameters from a generalized master network is described. Trends in the areas of search algorithms, role of middlings and feed identification etc. are indicated.

Jan 1, 1989

By M. R. Shahan, C. E. Seaman, Mischler S. E., T. W. Beck

"Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce the risk of coal-dust-fueled explosions. The goal of this U.S. National Institute for Occupational Safety and Health study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust, smaller than 75 µm in diameter, in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity of 3.6 m/s (700 fpm). Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle should be operated at high fluid pressures to produce smaller droplets and move more air. These findings agree with past respirable dust control research, providing guidance on spray selection and spray array design in ongoing efforts to control airborne float dust over the entire longwall ventilated opening. IntroductionCoal mining processes produce airborne dust that naturally deposits on the floor, roof and ribs of mine airways. These fine dust particles, termed float coal dust when smaller than 75 µm in diameter, are deposited in the return entries of coal mines and can be reentrained by pressure waves induced by methane-air explosions (Rice et al., 1911; Nagy, 1981; U.S. National Institute for Occupational Safety and Health (NIOSH), 2006). These particles are also those most likely to participate in coal-dust-fueled explosions, which can potentiate and propagate explosions resulting in extensive damage. In order to meet compliance requirements of at least 80 percent incombustible content in the composition of material deposited in mine entries (U.S. Mine Safety and Health Administration (MSHA), 2016), coal mines apply an inerting agent, specifically, rock dust (Harris et al., 2009). Should methane be present in the mine atmosphere, the required fraction of incombustible content is further increased by 0.4 percent for each 0.1 percent methane. The removal of airborne float coal dust (AFCD) prior to deposition is an approach intended to make current rock dusting practices more effective by increasing the proportion of inert material to combustible material, resulting in a lower risk of coal-dust-fueled explosions."

Jan 1, 2018

By B. N. Hira

A multistoreyed residential complex was at the penultimate stage of construction by ONGC at Nazira, Assam. The site was situated at high earthquake zone. The subsoil was very weak and contained soft to medium clay with water table almost at the ground level. The bearing capacity of soil was quite poor particularly with predicted settlement beyond permissible limit. In this situation, the conventional shallow and deep foundations were found uneconomical and ground improvement with granular piles was considered as the viable solution. ONGC approached the Central Building Research Institute with the request to design granular piles along with R.C.C. foundation and other suitable cost effective measures. CBRI collected relevant geotechnical informations and supplimented the data by conducting field tests at site and laboratory tests at Roorkee. Rational design of 30 cm dia. and 5.00 meter deep granular piles were suggested with isolated and combined RCC footings over the reinforced soil. In addition to several structural and geotechnical advantages, the granular pile foundation provided considerable economy in the cost of construction. The paper presents the salient geotechnical and structural informations of the challenging project and provides the design details of the innovative granular pile-system. It also furnishes the design approach of the RC footings and other elements of the foundation.

Jan 1, 1996

By George H. Roseveare

Early flotation dealt primarily with the bulk concentration of sulphide minerals or the separation of one sulphide from another and was referred to as oil flotation because oils and fats were used as reagents. The separation or concentration of one nonmetallic mineral from another developed later with the use of fatty acids. Fatty acids are organic acids present usually as glycerides in tall oil and oils of fish, peanut, cottenseed, soya beans and ethers of veg¬etable and animal origin. Some, of these oils and their derivatives were used by the Phoenicians as early as 600 B.C. in making soap, and the use of such reagents in mineral dressing is referred to as "soap flotation". The first use of oleic acid for the recovery of minerals was the early agglomeration process.' The coarse particles of ore, from 1/16 to 1/4 inch diameter, were coated with large amounts of soap or oil and after screaming from the gangue were recovered by screening, hydraulic or table classification. In 1886, a patent was issued to Mrs. Carrie Everson in which the essential feature was the constituted commingling of pulverized ore, fat or an oil, either animal, mineral, or vegetable, for the purpose of effecting .a. union of the free metal or metallic portion of the ore with such admixed material whereby the same may be changed in subsequent separation of quartz or other rock therefrom by washing or other suitable means. The patent mentions the use of red, cotton seed, caster, sperm and linseed oils, In the early use of collectors the amount of oil for froth flotation was often 2 to 6 per cent by weight of the ore rather than pounds per ton.

Jan 1, 1959

By Gustavo Brunello

Motor Failure Rates and Cost ? Motor failure rate is estimated: 3-5% per year. ? In Mining, Pulp and Paper industry failure rate is up to 12%. ? Sometimes process downtime costs are higher than motor ?? Motor failures are due: Electrical 32% Mechanical 31% Environmental 36%

Feb 1, 2008

By Y. Lizotte

The purpose of this paper is to describe a stochastic simulation program used to assess several dispatching rules applicable to small scale computerized systems for optimizing truck/shovel productivity. The system studied is semi-automated with a dispatcher communicating instructions by two-way radio. The simulation program is structured on an advance clock approach which enables the insertion of dispatching rules at various points in the haulage net- work. The rules tested include minimize shovel idle time, maximizing immediate truck use and assigning trucks to shovels to meet specific production objectives. A variation of the traditional "Match Factor" is implemented to maintain fleet balance throughout the shift. A mine case study demonstrates how the dispatching rules increase productivity of such semi-automated dispatching systems. Practical problems involved in the implementation of small computerized dispatching systems are also discussed.

Jan 1, 1986

By Charles Bohdanowicz

The accompanying tables' show that in 1936 production of crude oil in Poland decreased very slightly (Tables 1 and 5), by about 1 per cent, and that gas production increased by about 11 per cent. As in preceding years, drilling (Tables 1, 2 and 3) was devoted principally to extension of oil fields in the Jaslo district (fields 1, 5 and 7) and, in a lesser degree, of those in the Stanislaw6w district (field 27). Production of crude oil is being sustained in a large measure by the deepening of old wells; besides a total number of 183 new wells completed (Table 3) about 152 wells were deepened, and in a general way the results of deepening were better than those of new wells drilled. Reserves of "proved land" have not increased as far as crude oil is concerned, but a notable extension of gas fieldsZ was attained in Daszawa (field 25) and in the Roztoki area (field 5). In the sub-carpathian zone gas fields have been proved in the vicinity of Kalusz, Kos6wJ and in the northwestern sector of that zone, between Tarnow and Lezajsk. The gas horizons of Daszawa occur in the Upper Tortonian, those of Kos6w in the Lower Tortonian (Middle Miocene). Exploratory drilling has been performed near Kalusz, and has been commenced near Kos6w and in the Tarn6w area. The Kos6w gas approaches the "wet" type. A possible gas reserve with a volume of 4,000,000,000 cu. m. (141,000,-000,000 cu. ft.) has been calculated, for an area of about 5 sq. km. of the Daszawa field, on the basis of production obtained and of decreases in pressure and their distribution. The fields of Roztoki and Strachocina (No. 12) have not yet supplied sufficient data for a calculation of reserves, which might possibly be estimated at 2,000,000,000 cu, m. (70,000,-000,000 cu. ft.).

Jan 1, 1937

By J. J. Jakosky, D. H. Zellers

"IntroductionThis paper is the seventh of a series describing an investigation being conducted by the Bureau of Mines on underground communication. A review of past work and results obtained has been published. The present paper deals with a study of line-radio or wired-wireless methods of communication, herein electrical energy is transmitted by metallic conductors.The use of line-radio over metallic conductors has been practiced for a number of years, and at present is being used on a large scale in long-distance carrier-current telephone and telegraph. The early work of the U. S. Army Signal Corps and the Bureau of Standards in using ordinary radio transmitting and receiving apparatus for communication over metallic conductors was been descried. Later publications describe commercial applications, and an excellent treatise and resume is given by E. Colpitts and C. B. Blackwell.Scope of ReportThis report contains (1) a discussion of the chief factors affecting carrier-current transmission, with particular reference in application to underground communication for mines; (2) a description of typical underground circuits used for power and lighting; and (3) description of apparatus used and results obtained in line-radio experiments in coal mines near Pittsburgh, with circuit diagrams, and conclusions as to power requirements and limitations for mine use."

Apr 1, 1925

By Jason J. Ballentine

This paper presents a case study of how an asset strategy and zero based budget was developed for an existing crushing plant that had been purchased from the contract service provider by an Australian Iron Ore miner. The goal was to directly align the strategies and budget to the business goals. This however was not a simple task due to poor historical records and a general lack of information. These challenges were overcome and the benefits of a documented maintenance strategy, a justifiable zero based budget and employee engagement were realized.

May 1, 2007

By Leoncio Méndez, Jesús Arguijo, Juan José Frausto, Daniel Castruita, Daniel Aguilar

Minera Sabinas (Grupo Peñoles), localizada en Sombrerete, Zacatecas, México, produce concentrados de cobre y zinc. Su proceso es un circuito de conminución de quebradoras y dos molinos de bolas en circuito cerrado con hidrociclones seguido de un circuito de flotación, a partir de mineral polimetálico extraído de una mina subterránea. Su problemática consiste en que la recuperación por flotación disminuye significativamente cuando minerales con contenido de pirrotita son procesados. La flotabilidad natural de la pirrotita supera la cinética de flotación de las especies de cobre y zinc y limita la capacidad de la concentradora para generar concentrados vendibles. Este artículo presenta un diagnosticó de los problemas que se tienen cuando se procesan minerales con alto contenido de pirrotita, así como resultados de un programa experimental a escala laboratorio realizado en el CIDT de Peñoles y en sitio. La investigación se enfocó en definir un esquema de reactivos para poder procesar minerales con pirrotita en su composición. Compósitos de alta y baja ley de cobre fueron usados en la investigación. Se identificó el agua de proceso como una fuente de iones calcio y sulfato. Se desarrolló un esquema de reactivos orientado a promover la selectividad de las especies de valor respecto a la pirrotita, incluyendo tratamiento del agua de proceso.

Sep 20, 2019

By R. R. Sayers

"According to the dictionary,3 an accident is an event that takes place without one's foresight or expectation, often an undesigned, sudden, and unforeseen occurrence of an afflictive or unfortunate character. However, actual experience with accidents, the second most important cause of death in the United States,4 and a more extensive and scientific inventigation of their causes indicate that from 75 to 90 per cent of accidents are avoidable.5 This is borne out by the results of a three-year study of the accident records of 64,000 motor vehicle operators in New York6 which show that certain drivers are prone to accidents, that accident experience is traceable to certain causes, and that accidents don't just ""happen,"" It is estimated that 97,000 persons were killed by accidents in the United States in 1929 and 15,000,000 were injured. Of these about 23,000 deaths were due to so-called industrial accidents. In a list of accident rates by industries, compiled by the National Safety Council7 from reports of member establishments, mining heads the list, in both frequency (74.43 per 1,000,000 man-hours worked) and severity (9.9 days lost per 1,000 man-hours worked). These figures are very much higher than for any other industry; theindustries showing figures most comparable to mining are meat packing with a frequency rate of 55.94 and a severity rate of 1.47, construction with a frequency rate of 50.41 and a severity rate of 4.62, and refrigeration with a frequency rate of 43.35 and a severity rate of 3.04.While there is no way to determine the actual cost of all accidents from a monetary standpoint, estimates indicate that the cost will run into hundreds of millions of dollars annually.Cost of accidents in metal mines.- The United States Bureau of Mines obtains accurate figures on the number of lost-time nonfatal accidents as well as fatal accidents in the metal-mining industry.8 In 1926 the metal mines employed 127,823 men; 430 men were killed and 30,350 men received lost-time but nonfatal injuries as a result of accidents. Each of these fatal and nonfatal injuries averaged 114 days lost time, computing a fatality as 6,000 days lost time. This is equivalent to 3,523,944 days time lost due to accident, or at $5 per day per man, to a wage loss of $17,619,720. Deducting one-ninth of this figure for compensation paid, the metal miner loses in wage annually about $15,700,000, or about $122 per individual. This average loss per individual includes the cost of fatal accidents reckoned at 6,000 days or $30,000, but even if the loss in time due to fatal accidents be deducted, the average cost to each individual metal miner each year for nonfatal accidents is about $32. Estimating the loss to the metal-mine employer as about the same as that to the employee, the annual cost of metal-mine accidents to the employer is about $15,700,000 and to the employer and miner is $31,400,000."

Oct 1, 1930

The Proceedings of the above Symposium have been edited and published by the Symposium Committee. The Symposium was sponsored by the Australian Coal Association, the Joint Coal Board, and the United Nations Economic Commission for Europe. The Symposium was very well attended, with presentations from fourteen countries, including all the major coal-producing countries of the world. The Proceedings are presented in two parts: the Symposium Part and the Workshop Part. The Symposium Part deals basically with the theoretical aspects of outbursts and high-gas emissions in mines, while the Workshop Part is more practically oriented and describes case studies, and the management systems, and drilling technologies used in underground mines.

Jan 1, 1996