Search Documents

By M. J. Saarivirta

A high-purity copper-zirconium alloy system was imesti-gated. The zirconium content of the alloys studied varied from 0.003 to 0.23 pet. The solid solubility of zirconium in copper and some physical and mechanical properties of the alloys have been determined. By proper heat treatment, Cu-Zr alloy can develop a high electrical conductivity and resistance to softening at temperatures up to 500°C (930°F). This combination of desirable properties makes this alloy superior, to other com-merzcrrl copper base alloys for- use in the electrical conductor field. DEMAND for high conductivity copper alloys that retain their mechanical properties at elevated temperatures is growing rapidly. At present, copper-base alloys such as copper-silver and copper-chromium are used where these characteristics are required. As an example, commutators in electric motors are often made of these alloys. However, the life at elevated temperature of commutators made of copper-silver alloys is much shorter than the life of the same part made of copper-chromium and copper-zirconium alloys. Copper-silver alloys are subject to creep and subsequent failure when the service temperature exceeds several hundred degrees centigrade. Use of copper-chromium alloys has been known for the past several years, but little information is available in the literature concerning the properties of alloys in the copper-zirconium alloy system. Some work had been directed toward determining the solubility of zirconium in copper as well as determining properties of the Cu-Zr alloys. These investigations have revealed the superior high-temperature and electrical conductivity properties of copper-zirconium alloys over copper-chromium alloys. The United States Metals Refining Co., Carteret, N. J. has recently produced OFHC R copper-zirconium alloys for experimentation and evaluation. Because OFHC R copper contains no appreciable oxygen, no harmful oxides are formed and the full benefit of Zr as an alloying addition is obtained. This paper describes the results of this work. It contains room-temperature and some high-temperature data which have been obtained after various processing techniaues. Actual elevated temperature properties are being determined and will be reported in a separate paper. Preliminary results obtained at elevated temperatures suggest that the Cu-Zr alloy is superior to other high conductivity copper-base alloys. WORK PROCEDURE The high-purity oxygen free (OFHC R) copper-zirconium alloys with zirconium content ranging from 0.003 to 0.23 pct were cast into 4-by 4-in. wirebars by both continuous casting and conventional casting methods. Zr was added in the form of a master alloy containing 30 pct Zr and 70 pct Cu. Castings were analyzed for zirconium and nine bars containing various amounts of zirconium were selected for this study. The results of analyses and the sample numbers are given in Table I. Typical analyses of OFHC R copper are also shown. The following properties were studied: A) Solid solubility of zirconium in copper. B) Effect of zirconium on properties of copper. C) Effect of combined working and heat treating on properties of Cu-Zr alloys. The solid solubility of zirconium in copper was determined by metallographic techniques. Specimens for this phase of the investigation were hot rolled at 900oC (1650oF) to 0.250-in. rod. The rolled rods were cut into 2/3-in. long specimens and solution annealed at 950 °C (1740°F), 980°C (1795 °F). and 1020 °C (1870 °F) for 6 hr and quenched in water. In order to find the solid solubility limits at lower temperatures, the homogenized specimens were reheated at various temperatures for 1 hr and quenched. The physical and mechanical properties were determined on 0.250 in. rod, 0.132- and 0.081-in. wires. The wires were cold drawn from the 0.250-in. rods after they were solution annealed at 980 °C (1795°F) and quenched in cold water. Mechanical and electrical properties were determined on cold drawn and

Jan 1, 1961

By S. B. Patton, T. Novak

To fully utilize a ventilation simulator as a planning and production tool, the network database must keep pace with mining progress. By using AutoCAD's™ attribute-definition function, the branch data and node coordinates can be stored as part of the branch-diagram file and updated with the drawing. Attributes are drawing entities that contain text which can he extracted in a standard spreadsheet format or as an ASCII text file. The data can be subsequently loaded into a ventilation simulator. This paper presents the methodology for using AutoCAD's™ attribute feature in a ventilation simulation format.

Jan 1, 1995

Institute of Metals Division Ferrous and Nonferrous Physical Metallurgy Established as a Division April 26, 1918 (Bylaws published In the 1944 TRANSACTIONS Volume of the Division) A A SMITH, JR, Chairman E A ANDERSON, Past-Chairman F N RHINES, Senior Vice-Chairman W A DEAN, Vice-Chairman H A MALONEY, Treasurer ERNEST KIRKENDALL, Secretary 29 West 39th Street, New York 18, N Y Executive Committee R M BRICK 2 W A JOHNSON 1 H I DIXON 2 E W PALMER 1 M GENSAMER 2 J H SCAFF 3 J D HANAWALT 1 J D SULLIVAN 3

Jan 1, 1952

By Harlan A. Walker

This paper on the mines of El Potosi Mining Co. is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of North America. Grateful acknowledgment is made of the helpful suggestions and criticisms offered by the management, together with the assistance of the mining staff in preparing maps and drawings and of C. L. Thornburg, mine geologist, in preparing the section on geology.

Jan 1, 1934

By Steven R. McCutcheon

"The Bathurst-Newcastle district, a subcircular area approximately 50 km in diameter, contains 37 massive-sulfide Zn-Pb-Cu deposits that have defined tonnages, and has 58 additional significant occurrences. The largest deposit is Brunswick No. 12, with total reserves (including past production) of 148 million tonnes grading about 12.5% combined Pb-Zn. The deposits/ occurrences are spatially associated with a felsic volcanic pile that contains a significant sedimentary component. In the vicinity of the Brunswick deposits the pile is divisible into lower and upper sequences. The lower is characterized by megacrystic rhyolite (QFAS) and coarse- to fine-grained quartz (± feldspar) wackes and/or tuffites (QAS); the upper sequence is characterized by aphyric to sparsely porphyritic rhyolites (HWR), micro-breccias, and acid hyaloclastites with interbedded dark gray sedimentary rocks. A greenish gray to dark gray siltstone (GGS) separates the two sequences and hosts the sulfide deposits. Lithogeo chemistry of least altered samples shows that the QFAS and HWR have an igneous character, whereas the QAS and GGS have a sedimentary signature. The two types can be distinguished on the basis of total alkalies (Na2 + K2O) versus SiO2/Al2O3 and Ti02 versus Fe/(Fe +Mg). Some trace elements, such as Sr and Y, also help differentiate the two types. The QFAS differs from HWR by having higher La/Yb ratios but lower Zr and Th. The Bathurst deposits do not show a close spatial association with rhyolites but rather are stratiform bodies Oacking clastic textures) within fine-grained sedimentary rocks. The scarcity of barite and other sulfates indicates that there was little mixing between the metal bearing fluids and cold seawater. High Fe/(Fe+Mg) ratios in chlorites also indicate the fluids did not contain a significant seawater component. These features and the large size of many deposits suggest that the deposits formed from metal-rich pore waters that were released catastrophicallyfrom an acquifer in the footwall stratigraphy."

Jan 1, 1992

By T. F. Witherbee

IN the sections, Figures 1, 2, and 3, are shown three crucibles that have been applied to substantially the same furnace, all the conditions having been the same except a variation of one foot of bosh, and a slight variation in the angle of the same. The bosh of No. 3 was originally the same as No. 2, the additional foot in diameter being the result of three months' cutting. Beginning with No. 1, which was 5 feet 6 inches diameter, with tuyeres 5 feet 4 inches high, and cinder-tap four feet from bottom, great trouble was found in holding iron a proper length of time, four hours being the outside limit when working well, and two hours or less if working badly. "Break-outs" through the iron

Jan 1, 1880

By Yi Luo, FENGLIANG WU

Explosions and fires originated from longwall gob due to the formation of methane-air mixture have been a severe threat to coal miner’s lives.Many numerical studies on coalmine fire and explosion hazards have focused on the airflow in roadways and mine gobs. However, most of these studies isolate the gob from its surrounding roadways, and the network analysis and the CFD method are applied independently tomodel the two classes of airflows. This approach greatly limits the ability of simulatingmine ventilation flow, especially unable to consider the effects of gob boundary conditions on air exchange between the gob and the surrounding airways. An innovative finite tube method (FTM) is developed to couple the one-dimensional mine ventilation network (MVN) and the 2D/3D gob flow field (GFF). In FTM, GFF is discretized into a finite number of flow tubes each of which is formed by any two adjacent stream lines. These tubes, representing the gob’s field flow, connect the MVN into a new coupling network. To solve the coupling model betweenMVN and GFF, an iterative solution technique is developed inwhich the MVN analysis is used to evaluate the boundary pressures for GFF simulation and in turn the FTM feeds the GFF results back to the coupling network. Based on the FTM approach, a model for gas migration in gob has been established for delineating the hazard zones of explosive methane concentration and spontaneous combustion. A computer program is developed to implement the FTM simulation. An illustrative example with five flow tubes representing the GFF is created to verify the stability and convergence of the FTM solution process. A simulation example also indicates that the accuracy of FTM is improved by 12% compared with previous method. Results of an application case show that the program is capable of quantitatively evaluating the gob’s risk zones prone for spontaneous combustion and gas explosion as well as performing risk analysis for various ventilation scenarios.

Jul 10, 2020

By John L. Walter

A sintered compact of iron containing 0.007 vol fraction of glass , prepared 6). powder rnetullurgtcal lechniques, was rolled lo foil, 0.001 in. /hick. The foil sullrples were anneuled a1 650° to 850°C in hydrogen. Pri,narj recryslullization prodtnced large grains which Lc3ere highly elongnled in the rolling direclion und which had an unusual prgferred orientation. The glass parlicles assumed a stringerlike dispersiorz on working; llie slrinyers were parallel lo the rolling direction and to the long axis of the grains. The same unusual grain structure, preferred orientation, and stringerlike dispersion of purticles are found in heal-ily rolled and annealed foil of tungsten which has heen doped wilh small amounts of aluminum, silicon, and polassiutvt. Both the proper dispersion of the particles and severe working (reductions in excess of 98 pct) are necessary to produce the elongzcted grain structure. RECENTLY, the author reported on the origin of the elongated or "nonsag" grain structure in tungsten foil which was doped with aluminum, silicon, and potassium.' It was observed that particles, identified as mullite (Al6Si2Ol3), were present in the doped ingot (as sintered) and at all stages of processing from ingot to sheet or wire. It was shown that the particles, being plastic at tungsten working temperatures (up to 1550"C), underwent a "stringing out" parallel to the working di-direction. It was concluded that these strings of particles were responsible for the formation of the highly elongated interlocking grains observed in doped tungsten wire or sheet. To give further credence to this explanation of a long-observed but not understood phenomenon, it was decided to design a new system, one which was analogous to the doped-tungsten system. Thus, a bcc metal, iron, was chosen to be doped with glass which would be plastic at reasonable working temperatures for iron. The glass chosen was a #0080 Corning lime glass which melts at about 810°C. This is approximately the same fraction of the melting point of iron (0.6) as the melting temperature of mullite is of tungsten. It will be shown that all the observed unusual features of the doped tungsten are duplicated in the glass. doped iron, even to the preferred orientation of the grains in the recrystallized sheet. In the tungsten sheet the preferred orientation consists of two components, (1i3)(691) and (013)(362), neither of which has been observed as a component in textures of primary recrystallized bcc metals. EXPERIMENTAL PROCEDURE The glass, in the form of fine powder, was added to high-purity electrolytic iron powder and mixed dry. The particular composition chosen was 0.007 vol fraction of glass. After mixing, the powder was mechanically pressed to a disk 0.5 in. diam and 0.15 in. thick at a pressure of 5000 psi. The pellet was sintered, in pure dry hydrogen, for 2 hr at 8 50°C. The sintered pellet was then heated to 750°C and rolled to 50 pct reduction of thickness in two passes, with reheating between passes. The rolling temperature was then reduced to 600°C and the slab was rolled to a thickness of 0.050 in. Rolling to 0.010 in. was accomplished in several passes at 300°C. Final reductions to 0.003 and 0.001 in. were taken at room temperature. This rolling temperature schedule was similar, in terms of the fraction of the melting point, to that used in the rolling of the doped tungsten. The total reduction of thickness was in excess of 99 pct. Samples of the rolled foil were lightly electro-polished and annealed for 1 to 6 hr at temperatures of 650" to 85O°C in hydrogen. Samples for transmission electron microscopy were thinned on a Disa Electropol using AC-1 electrolyte.

Jan 1, 1968

By Alexandre de Aparecida Morais

No processo de lingotamento contínuo a secagem e o pré-aquecimento do refratário do distribuidor são de fundamental importância. Estes são realizados visando: reduzir a perda de calor do aço líquido, reduzir as bolhas nas primeiras placas, evitar respingos de aço (reações) ocasionados pela umidade e prevenir a degradação refratário por choque térmico. Para aços planos, os sistemas para promover a secagem e pré-aquecimento podem ser do tipo a "quente" (mais usual) ou a "frio". É denominado "partida a quente" quando se realiza a secagem e o pré-aquecimento; e de “partida a frio”, quando apenas a secagem é realizada. Têm-se como características distintas entre os processos: - A Quente: maior consumo de gás; forte degradação do refratário; temperatura de trabalho do distribuidor mais elevada, deteriorando as condições do ambiente; - A Frio: menor consumo de gás; redução da degradação do refratário; no entanto, exige um controle rigoroso da curva de secagem, o que implica maior investimento inicial no equipamento de secagem. Em 2002, após uma análise de viabilidades a ArcelorMittal Tubarão implementou o sistema de frio. Este artigo mostra a evolução deste sistema após a sua implementação, analisando a correlação com defeitos, a implementação de melhorias e os ganhos obtidos.

Jul 30, 2018

By Walter W. Kaufman

The braking performance of underground, rubber-tired, coal mining vehicles is evaluated. Surveys of mining equipment and braking manufacturers and underground stopping tests are discussed as they relate to this evaluation. Stopping performance recommendations are proposed.

Jan 1, 1977

I HAVE previously shown you in the Fifth Book the process of making guns and gun carriages, together with other preparations and methods of moving them. If I now failed to show you more about them, it would be as if I had pointed out only the useless shadow of a thing, for I did not show the kinds and arrangement of their supplies or how the effects for which they are made are achieved. For these reasons I now wish to tell you, in addition to what I have already said, how saltpeter is made and the methods of refining it well; what it is and how without it guns and many effects of violent and artificial fires would have been discovered in vain. After this, I also wish to tell you the methods of compounding the powders for large and small guns, and finally how these are loaded and discharged. I also wish to tell you how mines are made, and fire tubes, [149v] fire pots, squibs, fireballs, rockets, shells, grapeshot, and other similar devices for shooting fire in order to bum ships, supplies, bridges, and ramparts, or, in offense, for firing on batteries. I also wish to teach you to make certain bronze balls for shooting, which carry fire and break in many pieces when they hit. For surely, besides being terrifying to the sight, they would be harmful to armies lined up in battle when they are fighting. Likewise, I wish, to enlighten you as to how artificial fires are made that last long and are difficult to extinguish. Since these are fine and useful things in wars, every captain and soldier should give them consideration and know how to use them when necessary. You will be pleased to have this information if for no other reason than that you can teach it to those who take delight in celebrating holidays with festivities and with fires.

Jan 1, 1942

Acupan is considered to be an intrusive centre as several igneous phases have been emplaced in the vicinity of the mine over the past 8 Ma. They include the Lucbuban gabbro, Virac granodiorite, Ampucao dacite porphyry (ADP), Hartwell plug, Itogon plug and the multi-phase Balatoc diatreme. These intrusives have high-K calc-alkaline affinities and are grouped together as the Virac Complex.Porphyry-style mineralisation formed during the final crystallization of the ADP in the late Pliocene, with the deposition of two vein stages from high-temperature hypersaline magmatic-hydrothermal fluids. K-silicate alteration halos surround the first stage of veinlets (stage I); they are surrounded in turn by a propylitic assemblage. White sericite and/or intense propylitic halos envelop the second stage of veinlets (stage II) and grade into a weak nrnnvlitir accPmht o

Jan 1, 1990

By Alexandre Gonçalves Andrade

A Samarco Mineração utiliza combustível sólido para geração de energia térmica nas pelotas de minério de ferro. Este insumo torna possível a redução da utilização de gás natural na etapa de queima nos fornos de endurecimentos e ainda melhora a qualidade física das pelotas. O tamanho das partículas é chave para eficiência do processo e a cominuição destes combustíveis é realizada nas plantas de moagem da empresa, tanto para o antracito quanto para o coque verde de petróleo. Tradicionalmente, um dos principais itens de controle de moabilidade do insumo é o HGI (Hardgrove Grindability Index), que avalia a dureza do combustível sólido no processo de moagem. Porém, este parâmetro não reflete as dificuldades produtivas encontradas nas plantas de moagem da Samarco Mineração. Portanto, foi desenvolvida metodologia através de uma modificação da equação proposta por Bond para avaliação energética de moagem. A lei de Bond tem origem empírica e considera que a energia consumida na cominuição é proporcional ao comprimento das fissuras iniciais que se desencadeiam na quebra das partículas. A metodologia proposta, no presente trabalho, avalia com maior representatividade as dificuldades encontradas na cominuição destes insumos. Ainda, testes em planta piloto de moagem de combustíveis sólidos foram realizados para validação da abordagem.

Aug 1, 2018

By Alan Rice

Abstract-The mechanism by which stratiform ore deposits of PGE (platinum-group elements) are laid down in ultramafic igneous complexes is not completely clear. Early studies by the author and coworkers on numerical analyses of the convective cooling of low-Rayleigh-number magma chambers examined the effect of suspended crystal load on fluid density, and raised the possibility that the growth of the suspended crystal load during cooling could split a magma chamber into several convecting layers. The lower layers would have a higher content of refractory phases than the upper layers, which would consist of more evolved melt. This paper considers numerical modelling, as well as theoretical and experimental work in other fields dealing with suspended loads in fluids. The calculations, which are based on the physics of convecting magmas, yield quantitative relationships consistent with the observation that economically interesting stratiform PGE deposits are restricted to large magma bodies, and also yield estimation of the depth in a magma chamber at which certain grades of mineralization may occur.

Jan 1, 1997

By Alan Rice

The mechanism by which stratiform ore deposits of PGE (platinum-group elements) are laid down in ultrama?c igneous complexes is not completely clear. Early studies by the author and coworkers on numerical analyses of the convective cooling of low-Rayleigh-number magma chambers examined the effect of suspended crystal load on ?uid density, and raised the possibility that the growth of the suspended crystal load during cooling could split a magma chamber into several convecting layers. The lower layers would have a higher content of refractory phases than the upper layers, which would consist of more evolved melt. This paper considers numerical modelling, as well as theoretical and experimental work in other ?elds dealing with suspended loads in ?uids. The calculations, which are based on the physics of convecting magmas, yield quantitative relationships consistent with the observation that economically interesting stratiform PGE deposits are restricted to large magma bodies, and also yield estimation of the depth in a magma chamber at which certain grades of mineralization may occur.

Jan 1, 1997

By C. G. Dunn, P. K. Koh

Microstructure, magnetic torque, and texture data before and after grain growth were obtained on two 3.25 pet Si-Fe specimens having initially the same cold-rolled textures and the same primary recrystallization textures. The latter textures consisted of four components, two only of which were strong; the strong components were near (120) [001] and (320) [001]. The textures of the two specimens obtained by grain growth were different. In one specimen the two weak components were converted into strong components by a secondary recrystallization process; in the other specimen the primary recrystallization texture was retained by a normal grain-growth process. The difference in behavior of the two specimens was interpreted in terms of a difference in the relative grain sizes between weak and strong components; i.e., in terms of a geometrical factor that would alter the early growth rates of grains belonging to the two weak components of the texture. Specifically the growth rate was considered as the product of two terms: a driving force and a boundary mobility. The texture changes observed are considered to favor the oriented-nucleation growth-selectivity theory more than the oriented-growth theory. WHEN primary recrystallization and grain-growth textures form as a result of annealing deformed metals or alloys, the fundamental processes involved are nucleation and growth. Knowledge, therefore, about nuclei and the factors influencing their growth is required not only for the understanding of texture development but also for its control. In the oriented-growth theory of texture formation1, 2, 3 the problem of nuclei is generally disposed of by the assumption that nuclei are available in all orientations; the theory then has to explain the final texture from the initial texture and the way boundary mobility depends on orientation. In the oriented nucleation theory of texture formation"' nuclei are considered to be present only in certain orientations but the importance of growth selectivity is still recognized. For example, the mobility of boundaries of approximately the same orientation and of the coherent type in twins is believed to be low while that of high-angle boundaries, in general, is high. Because of this the theory may be described as an oriented-nucleation growth-selectivity theory. The main feature of the oriented-nucleation theory, however, is the importance given to nuclei; i.e., how they form in specific orientations and how they grow. In the present investigation two cold-rolled single crystals were used to study the effects of growth after primary recrystallization. The cold-rolled textures and the primary recrystallization textures were determined from portions of these specimens and reported earlier.",' The two cold-rolled crystals were in the (111) [112] stable end orientation, the recrystallization textures were nearly identical and consisted of two strong components, designated M and M', which were near (120) [00l] and (320) [00l], respectively, and also some specific weak components near (111) [110] and (111) [110]. It is well recognized that a single strong component in the primary recrystallization texture may be needed for secondary recrystallization3, 5, 8 but unfortunately when this is the case the amount of material left in deviating orientation may be too small either for growth or for positive identification. The present samples proved to be almost ideal for the study of minor components and their influence on texture changes produced by growth after primary recrystallization. The results obtained are interpreted in terms of present knowledge of grain-growth processes. Experimental Procedure Two lots of silicon-iron alloy of essentially the same composition, namely, 3.25 pet Si, 0.004 C, 0.009 P, 0.010 S, 0.035 Mn, 0.070 Ni, 0.090 Cu, 0.009 Sn, with traces of A1 and Cr and the balance Fe, were converted into single crystals 0.025 in. thick and 1.25 in. wide. The orientations were predetermined by the method of reorienting a seed crystal as described elsewhere.3 pecimen 1 from one lot had the (335) [556] orientation while specimen 2 from the second lot had the (111) [112] orientation.* Both crystals were cold rolled to a reduction in thickness of 70 pet while widening approximately 20 pet. Samples of each were selected for determining 1) the cold-rolled texture, 2) the time required at

Jan 1, 1959

By Sheldon Rideout, E. L. Kamen, B. S. Lement, Paul A. Beck, W. D. Manly

The 1200°C isothermal sections of the following ternary phase diagrams were investigated: Cr-Co-Nil Cr-Co-Fe, Cr-Co-Mot and Cr-Ni-Mo. In all these systems the u phase was found to form extended solid solutions. Two new ternary phases of unknown structure were identified. The existence range of intermediate phases of transition elements was correlated with 3d electron vacancy concentrations. THE occurrence of extensive ternary d solid solutions in the Cr-Co-Ni and in the Cr-Co-Fe systems was described in a brief note.' More recently d- solid solutions were also found in the Cr-Fe-Mo system by two independent groups of investigators.2,3 The existence of binary d phases in the V-Co and V-Ni systems, predicted in ref. 1, was experimentally discovered recently by Duwez and Baen and independently by W. B. Pearson, J. W. Christian, and W. Hume-Rothery.5 Duwez and Baen stated two general conditions for the occurrence of the d phase in alloys of the transition elements: "(1) The atomic diameters of the two metals do not differ by more than 8 per cent. (2) One of the two metals has a body-centered cubic structure while the other is face-centered cubic, at least in one of its allotropic forms." In the course of an extensive research program conducted at this Laboratory under the sponsorship of the NACA, several ternary systems, containing d solid solutions and also certain new ternary phases, were investigated. The present report describes the investigated portions of the 1200°C isothermal sections of the following ternary phase diagrams: Cr- Co-Ni, Cr-Co-Fe, Cr-Co-Mo, and Cr-Ni-Mo. It was found that the range of existence of the d phase in these four ternary systems, as well as in one of two ternary systems which were investigated by others, can be fairly consistently described in terms of electron vacancy concentrations. This supports the suggestion of Sully and Heal" that the d phase is an electron compound. Experimental Procedure The ternary alloys were prepared by vacuum induction melting in zirconia and alumina crucibles. Lot analyses of the metals used are given in Table I. Specimens of all alloys were annealed at 1200°C in an atmosphere of purified 92 pct helium and 8 pct hydrogen mixture. Alloys consisting mainly of

Jan 1, 1952

Occasionally it is interesting, and sometimes useful, to review the past for early references to our industry, and to learn of the trials and travail passed through before it arrived where it now is - and the results of such a review follow. Some time ago one of our modern playwrights and poets, Arthur Guiterman, turned to coal, with the following result : Afar in the Carboniferous time I grew in Paleozoical slime, A lepidodendron with boughs on my stem And lepidostrobusea grew out of them. My roots in the mud of the ages I spread And up to the heavens I vaunted my head, I throve in the heat of tropical sun, And now I am coal at two dollars a ton.

Jan 1, 1935

By Charles F. Hickey, Eric B. Kula

Thermomechanical treatments applied to the maraging steels include a) cold working in the austenitic condition at 650°F, followed by transformation to martensite and aging, b) cold working in the murtensitic condition and aging, and c) cold working in the aged condition with and without subsequent reaging. The strength increases in these steels are very small compared to the increases observed in conventional carbon and alloy steels. The changes that are observed are compatible with the strengthening mechanisms operative during thermomechanical treatment of conventional steels, however. Differences are caused by the absence of a carbide precipitate and the low work-hardening rate in both the solution-treated and the aged conditions. ThE 18 pct Ni maraging steels represent a class of steels which are finding great interest for high-strength applications.1~2 They are essentially carbon-free, and contain 7 to 9 pct Co, 3 to 5 pct Mo, and 0.2 to 0.8 pct Ti. Although austenitic at elevated temperatures, they can be air-cooled to room temperature to form a martensite, which because of the absence of carbon is relatively soft. On subsequent reheating age hardening occurs and strength levels of 250 to 300 ksi yield strength can be attained. These steels appear to be particularly suitable for studying the response to various thermome-chanical treatments for additional reasons other than the obvious one of attempting to improve their already attractive properties. Thermomechanical treatments can be defined as treatments whereby plastic deformation, generally below the recrystal-lization temperature, is introduced into the heat-treatment cycle of a steel in order to improve the properties. With an absence of intermediate transformation products on air cooling the maraging steels have good hardenability and hence can readily be cold-worked in the austenitic condition prior to transformation to martensite. Further, they can be worked in the martensitic condition prior to aging, and even can be deformed in the fully aged condition. Finally, it is of interest to compare their re- sponse to that of the more conventional alloy and carbon steels, where the role of carbides is important in the strength increase by thermomechani-cal treatments. The thermomechanical treatment of conventional steels has been the subject of a recent review.' I) MATERIALS AND PROCEDURE The steel used in this investigation was a commercially produced vacuum-melt heat, which had been rolled to 0.090 in. and mill-annealed. The composition of the alloy was as follows: 0.02 C, 0.08 Mn, 0.10 Si, 0.009 P, 0.009 S, 18.96 Ni, 7.34 Co, 5.04 Mo, 0.29 Ti, 0.05 Al, 0.004 B, 0.01 Zr, and 0.05 Ca. Unless otherwise stated the heat treatments used were the standai-d solution treatment at 1500°F for 1 hr, air cool, followed by a 900°F, 3 hr age. In this condition, the material exhibited 232 ksi yield strength and 239 ksi tensile strength. Mechanical properties were determined by Vicker's hardness measurement (20 kg) and by tensile tests on standard 1/2-in.-wide, 2-in.-gage-length sheet tensile specimens. Notch tensile tests were run using the 1-in.-wide NASA type, edge-notched specimen.4 Fracture-toughness determinations were made on 3-in.-wide, center-notched, fatigue-cracked specimens, following the recommendations of the ASTM Committee on Fracture-Toughness Testing.4 An electric-potential technique was used for measuring the crack size at the onset of rapid crack propagation5 which is necessary for calculations of Kc, the critical stress-intensity factor under plane-stress conditions. The critical stress-intensity factor under plane-strain conditions KI, was also calculated, using the stress at which the first observable crack growth occurred. 11) RESULTS A) Cold-Worked in the Austenitic Condition. The reported M, temperature for the 18 pct Ni maraging steel is about 310°F.1 Therefore, a temperature of 650°F was selected as suitable for rolling in the austenitic condition. Specimens were solution-treated at 1500°F for 1 hr, air-cooled to 650°F, and rolled varying percentages from 0 to 60 pct, at 20 pct reduction per pass. Tensile and hardness properties after aging at 900°F for 3 hr are shown in Fig. 1. The tensile strength increases from 253 to 271 ksi and the yield strength from 247 to 265 ksi as a result of a reduc-

Jan 1, 1964

By J. L. Lehman, J. D. Sudbury, J. E. Landers, W. D. Greathouse

A full scale field experiment on cathodic protection of casing answers questions concerning (1) the proper criteria for determining current requirments, (2) the amount of protection provided by different currents, and (3) the transfer of current at the base of the surface pipe. Three dry holes in the Trico pool in Rooks County, Kans., were selected for cathodic protection tests. The three holes were in an area where casing failures opposite the Dakota water sand often accur in less than a year. Examination of the electric togs showed the wells to be similar to other wells in the field where casing in four of seven producing wells has failed. The three holes were cleaned out and cased with 75 joints of new 51/2-in. 14-tb J-55. Each joint was visually inspected and marked before it as run. The casing was bull plugged and floated in the hole 50 that the inside might remain dry and free of excessive attack. Also, if a leak occurred, a pressure increase could be observed on gawge at the surface. Extensive testing was done, including potential profiles, log current-potentid curves and electrode measurements from both surface and downhole connections. Based on these data, a current of 12 amps was applied to one well and 4 amps to mother. The third well was left to corrode. During the two-year period when the casing was in the ground, [he applied current was checked weekly, and reference electrode measurements were made about every two months. Three sets of casing potential profi1e.c were run. When the three strings were pulled, each joint was examined for type of scale formed, presence of sulfate-reducing bacteria, extent of corrosion nttnck and pit depth. Since the pipe was new when run, quantitative determination of the protection provided by current was possible. This is the first concrete field evidence to help resolve the many arguments about the proper method for selecting adequate current for cathodic protection of oilwell (-using. INTRODUCTION A casing string is run when a well is drilled. This pipe is supposed to protect this valuable "hole in the ground" for the life of the well. Often the casing does not last the life of the well; it is with these casing failures that this work is concerned. The cost of repairing a casing failure varies from field to field—from as much as a $30,000 per leak average in California to $5,000 per leak in Kansas. Additional costs other than actual repairs are also important. These include formation damage, lost production, etc. Casing damage caused by internal corrosion is important in some areas. Treatment normally consists of flushing inhibitor down the annulus, but further research is being done on control measures. The test described in this paper is concerned only with external corrosion. The problem of casing failure from external attack has appeared in several areas including western Kansas, California, Montana, Wyoming, Texas, Arkansas and Mississippi. Cathodic protection is currently being used in an attempt to control external corrosion. From reports in the NACE there are thousands of wells currently under cathodic protection. The quantity of current being applied ranges from 27 amps on some deep California wells to a few tenths of an amp being supplied from magnesium anodes on wells in Texas and Kansas. Considerable field and laboratory effort1,9,5,6 was exented on the problem of cathodic prctection of casing, and it became fairly obvious that this method could be used to protect wells. Early workers showed that current applied to a well distributed itself over the length of the casing and was not concentrated on the upper few hundred feet. Basic cathodic protection theory had shown that corrosion attack could be stopped by applying sufficient current. The problem resolved itself, then, into one of trying to decide just how much current was necessary. Various criteria were utilized in installing the many existing cathodic protection installations. These methods included the following. 1. Applying sufficient current to remove the anodic slope as shown by the potential profile." 7. Applying enough current to maintain all areas of the casing at a pipe-to-soil potential of .85 v.' 3. Applying the current indicated by a log current-potential (or E log I) curve." 4. Supplying the current necessary to shift the pipe to-soil potential .3 v." 5. Applying 2 or 3 milliamps of current per sq ft of casing."