Search Documents

By Letícia Miranda Alves

Os fluxantes são misturas de minerais que em contato com aço irão fundir e gerar uma escória líquida que irá permitir a troca térmica e favorecer a lubrificação ao longo da interface placa/molde. Durante o processo de lingotamento contínuo de placas parte do filme de escória irá solidificar-se tendendo a formar fases amorfas e/ou cristalinas. O aumento na temperatura de solidificação bem como a formação de camada cristalina reduz a transferência de calor e pode repercutir em uma pele de aço mais fina favorecendo o breakout. Por outro lado, estas condições, como promovem uma solidificação do aço mais cuidadosa reduz a formação de trincas longitudinais a quente, depressões entre outros defeitos. Neste trabalho usando o software Thermocalc® simulou-se a formação de fases para dois tipos de pós fluxantes em função da temperatura. Usando o software FactSage estimaram-se os valores de viscosidade. Através de análise por difração de raios-x, microscopia eletrônica de varredura e análise térmica diferencial, buscou-se estabelecer as relações entre as propriedades e resultados esperados para cada tipo de pó fluxante no processo de lingotamento contínuo de placas.

Jul 30, 2018

By José Carlos D’Abreu, Luiz Cláudio Pinto Oliveira

Os pós ou lamas de aciaria gerados nos sistemas de despoeiramento dos gases de exaustão do conversor LD têm papel relevante entre os coprodutos siderúrgicos devido às suas significativas gerações, dificuldades no manuseio e acondicionamento e expressivo custo para processamento e/ou disposição. Em contrapartida, o elevado teor de ferro que possuem lhes garantem um potencial de substituição dos materiais primários nos processos metalúrgicos. Um método desenvolvido para a reciclagem do pó de aciaria LD foi a aglomeração a frio via briquetagem, para utilização como refrigerante no conversor LD. O efeito refrigerante do minério de ferro é cerca de três vezes superior ao da sucata de aço. Os briquetes de pó de aciaria LD contém ferro em diferentes estágios de oxidação e assim, seu poder refrigerante se situa em uma condição intermediária. Neste trabalho são avaliados, teórica e operacionalmente, o efeito refrigerante dos briquetes de pó de aciaria em comparação com outros refrigerantes. Considerando que a sucata tem um poder refrigerante de 340 kcal/kg, constatou-se que o poder refrigerante dos briquetes é cerca de 1,8 vezes superior ao da sucata e o poder refrigerante das pelotas é 2,8 vezes superior ao da sucata.

Nov 3, 2019

By Rafael Sartim

A indústria siderúrgica possui aspectos ambientais associados ao seu processo produtivo ligados em grande parte à emissão de material particulado, efluentes líquidos e geração de resíduos. A emissão de material particulado ocorre durante diversas etapas do processo produtivo, cabendo a estes a aplicação de sistemas para o controle ambiental. Em especial, a planta de sinterização possui como característica emissões primárias ligadas à exaustão da máquina, e secundárias referentes aos sistemas de captações em linhas de peneiramento, retorno de finos e pontos de transferência de correias transportadoras. Para o tratamento das emissões secundárias, a ArcelorMittal Tubarão possui um sistema de despoeiramento. Em virtude de melhorias de processo e alterações na produção, o sistema necessita de uma maior vazão para atendimento à demanda atual. Neste contexto, este trabalho se propôs a avaliar e testar a técnica de supressão de pó em pontos de transferência entre correias transportadoras para verificar sua aplicabilidade. Como conclusão, constatou-se que esta técnica é aplicável em regiões específicas com bons resultados na redução de emissão visível. Além disso, o uso do supressor reduz a quantidade de captações necessárias ao sistema complementando o controle do atual sistema de despoeiramento.

Aug 16, 2017

By Leandro Nakamura Alves Vieira

O acirramento da competição no mercado de aço tem exigido esforços de inovação e redução de custos. Por sua vez, as técnicas agrupadas como ICME - Integrated Computational Materials Engineering vêm acelerando o desenvolvimento e a otimização de materiais e processos de fabricação. O emprego destas técnicas tem sido uma ferramenta extra para assegurar a competitividade na indústria. Neste trabalho o uso da termodinâmica computacional no desenvolvimento e processamento de aços elétricos é revisado através da discussão de exemplos. Cálculos de equilíbrios mais relevantes para o processo de fabricação destes aços (tanto de grão não orientado-GNO como orientado-GO) permitem obter informações sobre as transformações de fases, solubilização de precipitados (sulfetos e nitretos) essenciais para a obtenção de texturas cristalográficas ideais. Os cálculos são discutidos e comparados com resultados reais. Discutem-se ainda, cálculos no sistema aço-gás, e os efeitos da composição da atmosfera na formação de óxidos na superfície do aço. Tais cálculos são importantes para descrever previamente as transformações que ocorrem durante as várias etapas de fabricação, assim como os efeitos dos parâmetros de processo sob os aços elétricos. A aplicação da técnica permite otimizar o processamento e o desenvolvimento dos aços elétricos em diversos aspectos. As vantagens e limitações do método, assim como o potencial de outras técnicas de ICME, na área, são discutidas.

Aug 7, 2018

By Tiago Evangelista Gomes

O presente trabalho teve por objetivo verificar a influência do Nióbio na trabalhabilidade a quente de um aço inoxidável duplex do tipo UNS S32304 em condições similares às do processamento industrial, utilizando ensaios de torção a quente. Foram fundidas, em forno de indução a vácuo, 4 corridas experimentais: uma com a composição química padrão e as outras objetivando-se teores de Nióbio de 0,2%, 0,4% e 0,8%. Ensaios de torção a quente foram realizados em resfriamento contínuo a partir de 1.200ºC, e ensaios isotérmicos no intervalo de temperaturas de 1.200 a 900ºC. O aumento da fração volumétrica de ferrita em função do aumento da concentração de Nióbio melhorou a trabalhabilidade a quente destas ligas.

Jul 30, 2018

By C. F. Barter, H. G. Kreis, D. S. Weber

Before and during in situ mining at the Santa Cruz In Situ Copper Mining Research Project test site, hydraulic testing was conducted at injection and recovery test wells to characterize patterns of fluid movement in the 5-spot well field. Testing included borehole spinner flow meter surveys, single-well and multiple-well injection and recovery tests, straddle packer injection tests, and bromide pulse tracer tests. Results of hydraulic testing for determination of fluid flow regimes were used to modify well and mining zone hydraulics for the purpose of increasing fluid migration in flow pathways of the mining zone with higher copper grade.

Jan 1, 2000

By Adauto Martins de Assis, Atan de Assunção Cardoso

Devido a sua alta demanda de produção e padrão de qualidade a indústria automotiva tem utilizado ao longo da história robôs nas mais diversas atividades como montagem, soldagem, pintura e inspeção. No intuito de levar esta realidade para a sala de aula de alunos de Engenharia Mecânica, foi desenvolvido um braço robótico didático, apresentando configuração semelhante à um modelo industrial, a ser utilizado como ferramenta de apoio ao ensino de robótica e outras disciplinas correlacionadas. Para isto, fez-se o uso associado da placa eletrônica Arduino e do software Matlab. Inicialmente foram obtidas as equações de cinemática direta e inversa. Os resultados mostraram que a posição teórica obtida apresentou um comportamento esperado conforme a metodologia adotada e o resultado experimental mostrou pequena variação de posição. Para a cinemática inversa, o tempo de resolução do conjunto de equações foi comparado à resolução do problema através de um método numérico. Com base nos resultados experimentais, foram feitas algumas sugestões de melhoria para o braço robótico didático e considerações relacionadas a acurácia de um robô industrial.

Oct 1, 2019

By B. H. Kear, S. M. Copley

Stress-stvain curves are presented for Ni3Al (y') cvystals in several ovientations, deformed in tension and compression at constant displacement rate, at temperatures from 70° to 2000°F. Both the yield stress and wovk havdening increase with temperature, with the magnilude of the effect dependent on ovientation. The yield stress maximum occurs at 1500°F in [001], at 1400°F in [011], and at 1200°F in [111]. The suppression of the yield stress peak in [011] and [111] orientatiorzs is due to the onset of cube slip, rather than octahedval slip, a1 elerated temperatures. The temperature and orientalion dependence of work hardening in nominal single slip orientations corvelates with changes in the CRSS ratio for octahedral slip and cube slip, in agreement with a model for work hardening based on pinning of screw dislocalions by cross slip from an octahedral plane into a cube plane. It is concluded that the unique plastic properties of y' have a decisive influence on both ductility and strength characleristics of y +y' nickel-base superalloys. It has long been recognized that the strength of y + y' nickel-base superalloys depends on the precipitation of the y' phase [basically Ni3(Al,Ti)]. This paper presents new data on the strength characteristics of single crystals of simple y' (Ni3Al), and forms the first step in a systematic program aimed at elucidating the mechanisms of hardening in the complex commercial alloys. 1) EXPERIMENTAL PROCEDURE Single crystals of off-stoichiometric NiA1 were grown from the melt under vacuum by a modified Bridgman method. The melt was poured into a preheated alumina mold and crystal growth was promoted from one end by gradient cooling. The crystals were homogenized by annealing in hydrogen at 2400° F for 72 hr followed by furnace cooling. Chemical analysis of samples taken from several crystals gave an average composition of 88.2 wt pct Ni. Spectrographic analysis gave as the principal impurities in weight percent— Si (0.02), Mg (0.01), Fe (0.02), Ti (0.002), Cu (0.008), and Co (0.03). Tensile specimens with specifications as in Fig. 1 were prepared by a series of operations involving electrical discharge machining, precision grinding, and electropolishing. Compression specimens with dimensions 1/4 by 1/4 by -3/4 in. were prepared in a similar manner, except for the initial shaping operation using a precision cut-off wheel/two-circle goniometer unit to give selected crystal orientations. Specimens were deformed in a Baldwin-Wiedemann testing machine with furnace attachment, using a strain rate of 5 x 10-4 sec-1. The strain measuring device consisted of extension arms attached to the tensile grips (or compression plattens) at one end and leading out of the furnace to an LVDT at the other. Temperature was controlled by a thermocouple placed in contact with the specimen. According to the known phase diagram for the Ni/A1 system,' when an alloy of the specified composition is cooled from the melt, primary y (nickel solid solution) dendrites grow at the expense of the liquid phase, which becomes enriched in aluminum. At the eutectic composition the remaining liquid freezes as a two-phase mixture of y + y' (Ni3Al). Upon further cooling, a solid state transformation occurs, involving the precipitation of y' in the primary dendrites, and the complete transformation of the eutectic mixture to massive y'. The as-cast structure consists, therefore, of y + y' dendrites with interdendritic regions of massive y', i.e., transformed eutectic, Fig. 2. 2) DISCUSSION OF RESULTS 2.1) Stress-Strain Curves. Fig. 3 shows tensile stress-strain curves for crystals in orientations close to [001] deformed at temperatures from 70° to 2000°F. Both the yield stress and total elongation are strongly temperature-dependent. At 70°F, easy glide is absent, and the work hardening coefficient BIT - G/300. At T > 1500°F, the negative slope of the stress-strain curves is due to pronounced necking in the crystals. The yield stress maximum at 1500° F corresponds with a minimum in the ductility, Fig. 4. The extensive duc-

Jan 1, 1968

By Kim B. Shedd

The Bureau of Mines measured fiber dimensions on crocidolites (riebeckite-asbestos and magnesioriebeckite-asbestos) from the world's four crocidolite mining regions. The objective of the study was to determine whether there are measurable morphological differences between crocidolite fibers that correlate with the high reported incidence of mesothelioma in miners and mill employees in the Cape Province of South Africa and Western Australia, as compared with little or no reported incidence of this cancer in the Transvaal Province of South Africa or Bolivia. Fiber dimensions measured with the scanning transmission elec-tron microscope showed that crocidolites from Western Australia and the Cape Province have more thin fibers than crocidolites from Bolivia and the Transvaal Province.

Jan 1, 1985

By D P. Obeng, L Reemeyer, R Holmes

The Zinifex Century Mine employs a large number of Detritor mills for fine and ultra-fine grinding to liberate silica and sphalerite at 80 per cent passing 7.5 microns before final zinc flotation. A joint project between CSIRO Minerals and the Zinifex Century Mine was carried out to evaluate the Detritor mill performance. Plant surveys were conducted around the Detritors in conjunction with laboratory tests. The survey data showed that the Detritors in the ultra-fine milling circuit performed well. They reduced a feed F80 sizing of 46 microns to a product P80 sizing of 7.5 microns at a gross energy consumption of 37.2 kWh/t. Scale-up of ultra-fine milling Detritors was studied using a 0.55 kW laboratory batch unit and a 355 kW full-scale Detritor by processing Century zinc concentrate with 1 mm sand media. The results indicated that the 0.55 kW laboratory mill underestimated the energy consumption of the full-scale Detritor by about 20 per cent for a product P80 of seven microns. The performances of a horizontal IsaMill and a vertical Detritor were compared as ultra-fine milling devices for processing Century zinc concentrate. The experimental data demonstrated that, when using the same grinding media, the energy efficiency of the two mills is similar despite the difference in mill designs. The Detritors used for regrind duty at the Century Mine performed poorly when processing feed at 80 per cent passing 88 micron. The energy consumption was high and the product size distribution was broad with particles above 100 microns in the feed unbroken and particles below ten microns overground. A coarser ceramic media of 3 mm was therefore tested in a laboratory Detritor to process the regrind Detritor feed as an alternative to the 1 mm Colorado sand used at the Century Mine. The ceramic media reduced the energy consumption significantly and produced a narrower product size distribution, which is more desirable for the downstream flotation process.

Jan 1, 2007

By Alix Thierart, Yann Rouillard, Bernard Catalano

Bessac's presence in Singapore started in 2014 with the construction of the Thomson metro line, which includes 18 miles of twin-bore tunnels and 22 stations split into 17 construction packages. Bessac joint venture was allotted the T219 lot. The works include the construction of a new 660-foot (200-meter) long transfer station, two parallel 19-foot (5.8 m) ID tunnels and a pedestrian underpass. The urban context and the very soft ground stratum imposed to utilize unusual tunneling techniques, from upgrading a slurry TBM to a high-density slurry TBM to launch with very low cover and canopy pipe roofing completed with a MTBM without retrieval shaft.

Jun 23, 2024

By F. B. Eiseman

IT is desired -to determine the effect of the extent of bank repairs on the final slag volume in acid electric steel-melting practice. It is understood that the repairs stud- TABLE I-Summary of Effect of Bank Repairs on Slag Volume [ ] ied here are necessary and the amount of sand added is that needed to maintain hearth and banks in a satisfactory condition. In this way the effect of repair materials on the amount of slag tapped would be found with a reasonable degree of accuracy. Ten heats were made for this study with careful attention to a uniform charge. The steel was the usual grade B and melting was carried out in a 3 1/2-ton top-charge Lectromelt furnace. Melting practice in all cases was the same-complete oxidation, with recarbonization by means of low-silicon pig iron.

Jan 1, 1947

Jan 1, 1990

By F. J. MacPherson, A. C. Caron

"Cassiar Asbestos Corporation Limited is at present B,C.'s only asbestos mining company, and has been actively engaged in the management and operation of the Cassiar Mine since the early 1950's. The Cassiar operations are located between 3,500' and 6,600' elevation in a secluded mountainous area of northern B.C., approximately 100 miles by road southwest of Watson Lake in the Yukon Territory. Climatic conditions in this area range from mild warm in the summer, to extremely cold during the long winter period.The minesite itself is located over a mile above sea level at the top of McDame Mountain, where year round 24 hours per day miners extract the chrysotile ore from the surrounding waste by standard open pit techniques. The ore body dips into the mountain at about a 45° angle, and as the mining progresses, larger stripping ratios are required. Waste to ore ratio this year will be more than 10 to l whereas only a few years ago ratios of 3 or 4 to l were possible. After drilling, blasting, and loading by shovel onto trucks, the asbestos ore is transported to the Primary Crushing Plant for crushing prior to transport by aerial tramway more than three miles to the Concentrator and Mill in the valley below, where the fibre is extracted from the barren host rock serpentine and milled into numerous grades for shipment to asbestos users round the world. The major air usage is associated with the milling process, presently requiring over 500,000 CFM, with future requirements expected to exceed 840,000 CFM by the end of the decade."

Jan 1, 1976

By Elisiane Maria Berton

Neste trabalho propõe-se o estudo do efeito do processo de SHTPN (Tratamento térmico de solubilização após nitretação por plasma), e do tratamento térmico de têmpera e revenido sobre a microestrutura, dureza e resistência à corrosão do aço inoxidável ferrítico AISI 409. Por meio do SHTPN obteve-se uma camada martensítica de nitrogênio na superfície do aço. Após o SHTPN as amostras foram temperadas de 950°C e revenidas nas temperaturas de 200, 400 e 600°C. A resistência à corrosão foi avaliada por meio da técnica de polarização cíclica e a dureza através de ensaios Vickers. Verificou-se que o SHTPN afetou significativamente a dureza do aço e o tratamento de têmpera refinou e melhorou a distribuição da martensita de nitrogênio. A camada martensítica formada apresentou espessura da ordem de 660 ?m. Os resultados indicam que é possível obter uma camada martensítica com dureza de 620 HV e aumento da região passiva, bem como do potencial de nucleação de pite quando comparado à condição não tratada (ferrítico). O melhor resultado de corrosão foi obtido para a amostra revenida na temperatura de 200°C.

Aug 8, 2018

By D. M. Larsen

Since start-up in 1985, the Cannon Mine has produced and shipped a 170-g/ton (5 oz/ton) gold flotation concentrate to various smelters for gold and silver recovery. Several processes have been investigated to economically produce done' at the mine site from the refractory concentrate. This paper describes laboratory and pilot scale test work used in the process design and engineering. feasibility study of a 73-t/d (80 stpd) pressure oxidation and carbon-in-leach (CIL) facility. The designed pressure oxidation circuit utilizes a series of verti¬cal autoclave units operating at 170°C (338F) and 1.4 MPa (200 psig). Projected operating costs are discussed.

Jan 1, 1993

By W. W. Adams

Coal mining in the United States, had a somewhat higher death rate per million man-hours of exposure among the employees in 1937 than in 1933 to 1936. However, the rate in 1937 was lower and therefore more favorable than that in any year since 1921 but previous to 1933. The nonfatal injury record, which began in 1930, was lower and therefore better in 1937 than in any other year since 1930. Separate figures covering bituminous-coal mines in all States showed a lower fatality rate in 1937 than in any year since 1920 but before 1933, and a lower nonfatal injury rate than that of any year since 1930 except 1933 and 1936. Reports for anthracite mines in Pennsylvania revealed a better safety record for fatal accidents in 1937 than in any year since 1930 except 1933, 1934, and 1936 and a better record for nonfatal injuries than in any year since 1930 except 1933.

Jan 1, 1940

By Francois Barthelat, Sam Goroshin, David Frost, Alexander Cappozi, Atefeh Nabavi

"In this study, a novel chromium–chromium sulfide cermet was produced by self-propagating high-temperature synthesis (SHS). Conventional techniques for manufacturing metal sulfides are complex, environmentally harmful, and not suitable for producing complex-shape articles. To overcome these disadvantages, a new method for the preparation of the metal-sulfur precursor charge is proposed, which can be described as reactive casting. The first cermet samples produced with the SHS process were found to be very porous, brittle, and have low mechanical strength. The possible sources for the generation of porosity were identified and analyzed and the process for manufacturing the cermet was modified. By improving the manufacturing process, the porosity inside the produced cermets was reduced from 70% to 12%.IntroductionMetal sulfide composites are in high demand in the chemical, metallurgical, and electrical industries because of their valuable characteristics such as hardness, semi-conductivity, electroluminescence, infrared transparency and catalytic properties. Current manufacturing methods for metal sulfides usually involve one of two different principal methods, including a complex multistage wet chemical process involving the precipitation of the corresponding salts from an aqueous solution with hydrogen sulfide, or hot sintering of the respective elemental reactant powders in a resistive furnace in a high-pressure inert or hydrogen-sulfide atmosphere [1, 2]. These conventional methods for synthesizing ceramic metal composites are complex, extremely time and energy consuming, environmentally harmful, and rarely able to manufacture articles with complex shapes. Therefore, in order to overcome these disadvantages, self-propagating high-temperature synthesis (SHS) was considered as an alternative method that offers significant improvements over the traditional cermet manufacturing methods [3]. SHS, which is a relatively new and attractive method for producing a wide range of advanced materials, is based on the self-sustaining feature of the highly exothermic reactions of the reactants. The SHS process results in high product purity, since the high temperatures generatedin the reaction cause any impurities to volatilize [4, 5]. SHS has low energy consumption and doesn’t require an external energy source and complex equipment, and it is self-contained [1, 5]. Since combustion synthesis has low power requirements, it is one of the few methods of materials synthesis that is feasible in outer space. Also, the process has a low cost and is capable of directly synthesizing articles with the desired shape, size and structure [5, 6]. The chemical reactions associated with SHS are typically completed in a few seconds leading to the formation of the condensed product. The high reaction rates and relatively rapid cooling in SHS reactions can avoid undesirable grain growth in products which often occurs with the conventional sintering method [3, 5, 7]. The traditional method for sample preparation in the SHS technique is to compact the reactant mixture powders in a steel die by a press to a typical density of about 80% of the theoretical maximum value, before igniting the mixture [8]. This method requires a large compression force to increase the green density and to minimize any pores in the green compact. To overcome these disadvantages, a new method for the preparation of the precursor charge in metal-sulfur by SHS is proposed which can be described as melt casting of a reactive mixture, or reactive casting in short."

Jan 1, 2012

By B McFadzean, N P. Lima, D A. Deglon

The reverse flotation of Itabirite iron ore is typically performed after a desliming step in which most of the sub-10 µm particles are removed. This is done to limit processing problems such as poor flotation recovery of SiO2 due to slime coatings and increased slurry viscosities, unmanageable froths and increased losses of hematite particles due to entrainment. However, the rejection of ultrafine particles contributes to large losses in iron recovery and may contribute to the instability of tailings dams. The aim of this study is to decouple the effects of ultrafine particles in the pulp and froth phases to better understand the processing capabilities of the fines fraction. The flotation test work was performed in a special-purpose continuously operated laboratory flotation cell that has a deep froth section to simulate plant-scale froth conditions. Five conditions of fines addition were investigated at three different froth heights and a solids concentration of 50 per cent. The behaviour of the pulp and the froth were decoupled using froth stability and froth recovery tests. This showed that, even though there is an exponential increase in froth stability at increasing fines quantities, the performance of the pulp has the overriding effect on the overall SiO2 recovery. Pulp zone, froth zone and overall SiO2 recoveries showed that overall recoveries increased by about 3.6 per cent for every 1 per cent decrease in fines content. This meant a large increase of 20 per cent in SiO2 recovery when going from undeslimed to deslimed feed. This was driven largely by increases in the pulp zone recoveries, which were about 4 per cent for every 1 per cent decrease in fines content. The froth recoveries, on the other hand, decreased by between 0.75 per cent and 2.5 per cent for every 1 per cent decrease in fines content, depending on froth height. This paper explores further insights into iron ore flotation processing at different slimes concentrations.

Aug 24, 2022

By P. Ramirez

"To achieve an optimal metallurgical performance in the flotation process the bubble diameter should be between 0.5 and 2.5 mm. To control bubble size, frothers are added, reducing bubble size and conferring bubble stability against coalescence. However, the bubble generation mechanism determines predominantly the bubble size distribution produced. In mechanical flotation cells, bubbles are produced by the shear stress generated by a rotating blade on a gas stream. This mechanism produces a log normal bubble size distribution. In contrast, in column flotation, jetting gas injectors are commonly used in Chile and the bubble size distribution is bimodal with small and large bubbles. Bubbles larger than 2.5 mm mean a loss in surface area, while bubbles smaller than 0.5 mm move with the pulp stream and therefore collide less frequently with particles. In this paper, a new device based on a jetting sparger and a deflector disc (impinging jetting) is evaluated as an alternative sparger for column flotation.The new device was tested in a rectangular acrylic cell 1 m × 0.5 m × 3 m. High-speed cinematography was used to compare bubble generation with jetting and impinging jetting at different gas velocity in the nozzle (5–50 m/s). From the image analysis, it was observed that the deflector induces a shear stress, in analogy to a rotating blade but in this case the shear results from a high velocity gas hitting a static surface. The device was evaluated in a 0.5 m diameter 3 m high column. The McGill bubble viewer technique was used to compare the bubble size generated by jetting and impinging jetting. It was found that the Sauter mean bubble diameter reduced from 7.4 mm to 2.8 mm, when the jetting sparger was modified with the deflector. In the case of the impinging jetting sparger, 70% of the bubbles were in the effective range for flotation, while for the jetting sparger, only 10% were in the effective range."

Jan 1, 2016