Search Documents

By H. C. Gatos, J. T. A. Pollock, V. Sadagopan

PREVIOUS investigations on the effect of neutron irradiation on the superconducting properties of bulk transition metals indicated that little or no change occurred in poly crystalline disordered materials, particularly if cold-worked prior to irradiation. Only the superconducting properties of ordered intermetal-lic A15 compounds were found to be sensitive to irradiation, and the observed reduction in Tc and increased magnetic hysteresis or critical current densities were attributed to the introduction of flux pinning vacancy clusters and disorder in the lattice. Since the former would also be expected to be present after irradiation in disordered alloys, the general conclusion was that the disordering effect of the irradiation was the primary reason for the changes observed. The present note reports some unusual effects of neutron irradiation on cold worked Nb(Cb)-Ti-V alloys. Specimens with nominal composition as given in Table I were prepared by repeated arc melting, taking the usual precautions, and homogenized at 1000°C for 24 hr prior to a reduction of 15:l by cold rolling. Samples of size 1 by 1 by 25 mm were sliced from the rolled strips. The sarmples chosen for irradiating were sealed in a cadmium tube (wall thickness 1 mm) prior to exposure in a fast neutron flux of 3.7 x 1019 neutrons per sq cm in the swimming pool reactor of Union Carbide Corporation&apos;s Sterling Forest Reactor. During irradiation the temperature of the samples was maintained below 70°C. The irradiated samples were stored at room temperature for approximately 1 year allowing the radiation levels to reach a safe handling value. Tc measurements were made employing a self-inductance coil technique. Jc data at 4.2"Kwere obtained using a four lead resistivity method. The latter measurements were made at the Francis Bitter National Magnet Laboratory by setting the perpendicularly applied field and increasing the direct current through the sample until a potential of about 10-6 v was detected. Tc values for the nonirradiated samples are listed in Table I together with the change in Tc after irradiation. A decrease in Tc of 0.25 or 0.3"K was measured for three of the four samples, the exception being the Nb-30 at. pct V-20 at. pct Ti alloy which showed a decrease of 0.5K. Jc vs applied field data are plotted in Fig. 1 for the Nb-20 at. pct V-30 at. pct Ti alloy. These curves are typical of the four alloys and surprisingly indicate that a degradation occurred in all the samples after irradiation. Hc2 values, obtained by extrapolation to zero current, are 8 to 15 pct lower than those measured for the nonirradiated specimens. The reasons for the degradation of Tc and jc ob-served in the alloys on exposure to neutron irradiation are not immediately apparent. The temperature at which the samples were maintained during bombardment (<70°C) and stored (20°C) make it highly unlikely that any significant change in the dislocation density of the materials through thermally activated migration and annihilation would occur. The explanation must lie in the type of damage produced by the bombardment. McEvoy et a1. reported no change in superconduct-

Jan 1, 1970

By Vern Miller

The Bureau of Mines developed a detector for controlling sorting devices to separate the copper-bearing fragments from the barren portion of Michigan native copper and western porphyry copper ores. A successful sorter could be used to preconcentrate the ore and eliminate costly hoisting or hauling of waste. An induction balance unit was developed and used in sorting tests on crushed sized -1+1/2-inch (-2.5+1.3-cm) ores from the Kingston (0.9 pct CU) and Centennial (1.6 pct Cu) mines of Upper Michigan. Concentrates of 4.0 pct and 7.5 pct Cu, respectively, were obtained at recoveries of 85 and 80 pct of the copper in the feed. Eighty percent of the sorted ore was rejected as tailing. Sorting larger fragments improved the separation efficiency. Tests on -4+2-inch (-10+5-cm) sized Kingston (1.6 pct Cu) and Centennial (2.1 pct Cu) ore samples yielded concentrates of 4.3 and 4.5 pct Cu, respectively, with corresponding recoveries of 92 and 91 pct. About 60 pct of the sorted ore was discarded as tailing. Porphyry copper sulfide ores also responded to electronic sorting but at a lower separation efficiency. Sorting response was affected by the degree of segregation.

Jan 1, 1976

By A. C. Callen

This, report represents the comments of the individual members of the A. I. M. E. Sub-committee on Physics of Mine Ventilation on the proposals of a special committee of the Institution of Mining Engineers (London). As might be expected, there is a certain diversity of opinions, for owing to the shortness of time- it was not possible for the sub-committee to get together for informal discussion. The report is presented in this form in the hope that it will bring out a full discussion by other members in the Institute. OLE SINGSTAD?, New York, N. Y.-The Atkinson formula, P =SV2 K a is quoted and it is stated that this formula is especially applicable to mine galleries but is unwieldy in application, as in many problems the value of K, S and a are assumed not to change. This is the same formula that was used during the preliminary calculations for the ventilation of the Holland Tunnel, and where the above-mentioned values were constant for a number of cases, it was a very simple matter to rewrite the equation n the form P = K1V2 and avoid the repeated use of identical figures. The Atkinson formula assumes 1. That resistance to flow is independent of the pressure. 2. Changes in volume due to change in pressure may be neglected. 3. Changes in density and viscosity may be neglected. 4. That the coefficient K is a constant. 5. That P is proportional to V2. We found, from our experiments in connection with the ventilation of the Holland Tunnel, that all the above assumptions could be safely made, with the exception of No. 3, and No. 4 at, very low velocities. In mine work, where many assumptions must necessarily be made, it would seem inconsistent to attempt to make any allowance for the other factors, which are so small that they can be determined only by the most careful experimental work. However, P does depend directly on the density of the air, and to that extent the Atkinson formula is incomplete.

Jan 2, 1926

By G. V. Smith, R. F. Mehl

The decomposition of austenite in steels, because of its immerse practical importance, has been subjected to extensive study in recent years from the point of view of the mechanism of the process.1"3 Although much information has been acquired, a number of questions, principally of theoretical interest, remain. One is that of the atomic-crystallographic mechanism by which each of the various reaction products forms. The isothermal reaction products of the eutectoid decomposition in plain carbon steels (to which this study is restricted) have conveniently been classified in three general groupings—pearlite, bainite, and martensite. Of these several products, pearlite and martensite have been studied extensively, but bainite has received only scant attention. -As a result, the mechanism of the formation of pearlite and that of martensite are now fairly well understood while a great deal of uncertainty exists regarding bainite. Pearlite Pearlite forms from austenite by the precipitation of alternate platelets of cementite and ferrite, which grow into the austenite matrix.2--5 The rate of reaction may be described in terms of a rate of nucleation and a rate of growth.2.3 Mehl and Smith6 have attempted to determine the lattice relationships existing between the ferrite in pearlite and the&apos; parent austenite. Using a pole-figure method of analysis, it was found that a limited number of ferrite orientations resulted from the decomposition of a single grain of austenite; it was not possible, however, to decide between two assumed ideal relationships, both of which appeared to account for the experimentally determined pole figure. It was definitely shown, however, that the relationship obtaining was quite different from that determined for the proeutectoid separation of ferrite.7 No attempt was made to determine the habit plane (matrix plane to which the precipitate lies parallel) of the pearlite lamellae. Belaiew8 earlier had stated that the number of directions assumed by the pearlite lamellae in a single grain of austenite was 12 (no details were given) and concluded wrong!:!, as Mehl and Smith6 have pointed out, that the lamellae delineate the {2I0} planes of ferrite.* Martensite It is known that martensite is a transiti0nal constituent of body-centered tetragonal lattice,&apos; and that it forms suddenly

Jan 1, 1942

By R. F. Mehl, G. V. Smith

The decomposition of austenite in steels, because of its immerse practical importance, has been subjected to extensive study in recent years from the point of view of the mechanism of the process.1"3 Although much information has been acquired, a number of questions, principally of theoretical interest, remain. One is that of the atomic-crystallographic mechanism by which each of the various reaction products forms. The isothermal reaction products of the eutectoid decomposition in plain carbon steels (to which this study is restricted) have conveniently been classified in three general groupings—pearlite, bainite, and martensite. Of these several products, pearlite and martensite have been studied extensively, but bainite has received only scant attention. -As a result, the mechanism of the formation of pearlite and that of martensite are now fairly well understood while a great deal of uncertainty exists regarding bainite. Pearlite Pearlite forms from austenite by the precipitation of alternate platelets of cementite and ferrite, which grow into the austenite matrix.2--5 The rate of reaction may be described in terms of a rate of nucleation and a rate of growth.2.3 Mehl and Smith6 have attempted to determine the lattice relationships existing between the ferrite in pearlite and the&apos; parent austenite. Using a pole-figure method of analysis, it was found that a limited number of ferrite orientations resulted from the decomposition of a single grain of austenite; it was not possible, however, to decide between two assumed ideal relationships, both of which appeared to account for the experimentally determined pole figure. It was definitely shown, however, that the relationship obtaining was quite different from that determined for the proeutectoid separation of ferrite.7 No attempt was made to determine the habit plane (matrix plane to which the precipitate lies parallel) of the pearlite lamellae. Belaiew8 earlier had stated that the number of directions assumed by the pearlite lamellae in a single grain of austenite was 12 (no details were given) and concluded wrong!:!, as Mehl and Smith6 have pointed out, that the lamellae delineate the {2I0} planes of ferrite.* Martensite It is known that martensite is a transiti0nal constituent of body-centered tetragonal lattice,&apos; and that it forms suddenly

Jan 1, 1942

By R. G. Davies

Above 500°C, where dislocation climb is rate controlling, it is observed that the activation energy for creep is independent of the apblied stress, although it varies from 62 kcal per mol at 15 pct A1 to 73 kcals per mol at 20 pctA1 due to the change in short-range ovdw with composition. Below 500°C, when the nonconservative motion of jogs upon dislocations is thought to be rate controlling, the activation energy is stress dependent. A sudden increase in the creep rate, for which no explanation is availab2e, occurs at the highest stress at all temperatures. CREEP has been the subject of numerous research publications during the past decade with most of the attention focused upon high temperature steady state creep, i.e., above 0.5 TM, where TM is the absolute melting temperature, as it is the most amenable to theory. Many of the proposed theories involve the climb of dislocations out of their slip plane, which allows them to circumvent obstacles or to annihilate dislocations of opposite sign on other slip planes.&apos; For pure metals it is observed that the activation energy for this creep is equal to the activation energy for self diffusion.&apos; The position is much more complicated in alloys as there are many possible microcreep mehanisms, as well as dislocation climb, which could be rate controlling. There has been little systematic investi- gation of alloys, but Weertman (lead and indium base alloys)3 and Lawley, Coll, and Cahn (Fe-A1 alloys)4 suggest a microcreep process as the controlling factor. A Cottrell-Jaswon atmosphere mechanism is proposed for the lead and indium alloys, and a mechanism involving crystallographic order for the Fe-A1 alloys. Lawley et al. showed that the formation of a super-lattice, either of the FeAl or Fe3A1 type. decreased the rate and increased the activation energy for creep. From the measurements of lattice parameters,= resistivity,&apos; magnetic properties,7&apos;8 internal friction: and dilatometry10 the ordered region is thought to commence at -19 at. pct Al. However, a recent investigation by the author indicates a value

Jan 1, 1963

By Maurice L. Pinel, Thomas T. Read, Thomas A. Wright

THE erroneous, but until recently widely prevalent, belief that iron castings were first made in Europe in the fourteenth century has been adequately refuted in a number of earlier papers;1,11,12 but except for an unpublished metallographic study by the late William Campbell, and a phosphorus analysis by T. A. Wright of the metal of the Han dynasty cast-iron stove described by Laufer,2 nothing was known of either the chemical composition or the metallographic structure of the metal of any ancient iron casting, although data on castings of recent manufacture are abundantly available. The metal of the stove, which had been buried in a grave for at least 15 centuries, was so corroded that it seemed inadvisable to publish the results on it until more and better specimens from other ancient castings could be obtained. During a journey through China, extending from Peking in the north to Canton in the south and Cheng-tu, Ssu-chuan, in the west, in the late summer and autumn of 1936, one of us (T. T. Read) was fortunate enough to obtain, and bring home for study, nine castings, all more than 1000 years old, of which the date of manufacture is precisely known because of inscriptions cast in them, another that lacks a dated inscription, but of which the date, as explained below, can be otherwise established, and a specimen from the largest iron casting ever made," which is also dated. The period covered by this suite of specimens extends from 502 to 1093 A.D. In addition, a sample was obtained from a casting of date unknown, but which was certainly cast before 1000 A.D. and possibly as early as the third century A.D. A detailed description of these specimens is as follows: 1. 502 A.D. A pair (right and left) of recumbent lions (Fig. 1). Base 7 ¼ by 14 3/8 in., height over-all 5 ½ in., weight 26 lb. each. The translation of the inscription on the base is: "Made on the twenty-fourth day of the seventh month of the third year of Ching Ming of Great Wei" (Sept. 11, 502 A.D.).

Jan 1, 1938

By G. R. Hopkins

"Summary An apparent decline in fuel efficiency at refineries, which first became came evident in 1930 and continued through 1933, was checked in 1933 when the average amount of heat needed to refine a barrel of crude oil amounted to 660,000 B.t.u. This compares with an average requirement of 692,000 B.t.u. In 1932 and with a low of 639,000 B.t.u. in 1929. (See fig. 1.) The improvement in fuel economy in 1933 probably was closely related to the increase of 5 per cent in crude runs to stills. As much of the fuel burned at refineries is utilized for purposes other than under crude-oil stills and in relatively stable amounts, it is evident that a material increase in crude runs will usually reflected in a decrease in average fuel requirements. Another factor which has influences fuel economy at refineries in the past is the trend in cracking, a refining process requiring more than the average expenditure of heat. In 1933 production of gasoline by cracking increased slightly, but no appreciable rise in heat requirements resulted as an equivalent amount of fuel was saved in improved technique, particularly in the field of heat exchange.Since the beginning of the refining industry, the transition in fuels has been from solid to liquid to gaseous; in other words, the leadership was first held by coal, then passed to oil, and is now held by gas. In 1933, 54.7 percent of the total heat units generated came from gas, 39.0 percent from oil (including acid sludge), and 6.3 percent from coal and coke. The principal change in the relative importance of the various refinery fuels in recent years has been the rapid growth in consumption of refinery or still gas at the expense of all the other common fuels. Still gas owes its ascendency to its cheapness and availability, and probably it would have become the primary refinery fuel years ago if recovery methods had been perfected. The relative importance of coal showed a small increase in 1933, the first gain recorded since these surveys were inaugurated in 1925. The increase in use of coal was undoubtedly due to increased operations at plants using it,"

Feb 1, 1935

By Glen Frank, David R. Chapman

Determining the number of boulders and cobbles that will be encountered in the tunnel envelope is one of the most difficult problems confronting the geotechnical engineer in the design of tunnels in glacial terrain. This issue is very important to the contractor, both in determining what methods will be used to construct the facilities and the advance rate that can be achieved for the chosen construction methods. The cost of constructing tunnels by pressurized face tunneling techniques is very sensitive to accurate characterization of the very coarse fraction (large cobble and boulder sized clasts), and no standard method is current available for characterizing boulders and cobbles. Careful use of large diameter borings and the sampling and analytical techniques outlined in this paper can provide a means to answer this difficult question. By performing large diameter borings and carefully recording and sampling the cobbles and boulders encountered, an estimate for the amount of these materials present in the formations sampled can be provided. Using this method allows the designer to communicate the expected geologic conditions to the prospective bidders in a manner that is both definitive and defensible. This paper describes the method as it was used in conjunction with the design of a large diameter sewer tunnel in the Columbus, Ohio area.

Jan 1, 2005

By J. J. Ormsbee

Attempts at coal-washing have been made in the southern states during the last twenty years; but it is only within the last four or five years that the practice has become at all general. It might perhaps be claimed as one of the blessings derived from our departed " booms;" for, during their sway, the supply of coal of all qualities, good and bad, could not equal the demand; but, with the subsidence of the inflated demand, came imperative calls for fuels of better quality; and washers, previously regarded as luxuries, became necessities. Among those now in use in this section are representatives of the following types or classes: the trough washer; the jig washer; the percussive table; and those washers in which a constant upward current of water effects the separation. Without having full statistics, it is safe to say that there are in successful operation in the South more washers of the last class than of any of the others. The purpose of these notes is to present data with regard to the constructiOn, operation, and results of one of these current-washers, based mainly on the plant at No. 2 Slope, Pratt Mines, Alabama. The coal is mined from the well-known Pratt seam, having here an average thickness of 3 feet 6 inches. It has distinct cleavage-planes, and breaks in cuboidal lumps; is bright black in color, firm in structure, and air-slacks only after considerable exposure. It burns freely, leaving a gray or buff-colored ash. The lump- and nut-coals are used for domestic and steampurposes (chiefly, however, for locomotive firing), and the slack for making coke. The specific gravity is 1.272. Analyses of Pratt Coal. I. 11. 111. IV. Min. Resources Authority. Phillips. McCalley. of U. s.,1892. Lupton. Fixed carbon,. . 67.90 61.600 64.30 63.82 Volatile material,.. 29.80 31.480 32.08 31.85 Moisture,.,...... 1.508 1.07 1.02 Ash,.... 2.30 5.416 2.08 3.31 Sulphur,. .. 0.83 0.918 0.47 0.70

Jan 1, 1896

H. H. Hill.—I believe that as petroleum engineers you are all more or less interested in geophysical prospecting. A large number of the papers that have been written on that subject are too detailed or too much involved to be of much value to a person who is not familiar with the subject, so I suggested to Mr. Fohs that he might bring us something that we could all understand. As I take it, we are interested in learning something about the different methods, the places where they have been used, their limitations and in general whether they have given satisfaction in locating oil deposits. F. J. Fohs, New York, N. Y.—I will briefly summarize some of the results as I Bee them from my practical contacts with them and my discussion of the subject with some of the more important rnen both in this country and Europe. Geophysical Methods 1. Seismographs: A. 1. Sonic refracting seismographs of Karcher, McCullom and Reiber. For rapid reconnaissance and also for detail—perhaps, the best type of instrument. 2. Mechanical refracting seismographs of the Weichert-Mintrop type. B. I. Sonic seismographs using reflected sound from contacts of sufficiently unlike beds where latter are thick enough, being used for detail of both salt domes and ordinary structures where a good reflecting key bed occurs. 2. Torsion Balances: Made in three sizes with greater portability and loss of but 20 per cent. in medium size and loss of 40 per cent. efficiency in smallest size. A. Used to best advantage in detailing salt domes, in noting anomalies of deep-seated structures of the Edgerly, La., type (but not always certain here and dependent on interpretation which involves both experience and the human equation to a large degree). R. Used to advantage in mapping faults where a lime or other denser bed occurs upthrown, and the topographic irregularities are not too involved. C. Of use where buried granite plugs and buried-hill structures occur as in the Western Texas fields. D. Believed of little use for other types of structure. 3. Magnetometers or Variometers: Now built horizontal and vertical with declinometer combined in one instrument. A. Practical in mapping granite or basic igneous rock plugs and intrusions, or of detritus therefrom. Adams has recently demonstrated definite results in mapping the well known Panhandle arch.

Jan 1, 1928

By E. H. Dix

The work of Merical and other investigators indicates that the phenomenon of age-hardening in alloys of the duralumin type is primarily dependent upon the variation in the solubility of copper with temperature. In addition to copper, however, these alloys contain small amounts of magnesium, silicon, manganese and iron, which may affect the age-hardening either directly or indirectly. The effect of these elements on the solubility of copper and on the manner in which this solubility varies with the temperature is of considerable interest, therefore. The effect of magnesium is of especial interest because apparently it exerts a marked effect on the natural or room-temperature aging of alloys of the type described.2 A series of investigations3 has been in progress in the research laboratories of the Aluminum Company of America to determine the functions * Metallurgist, Aluminum Research Laboratories. f Metallurgical Division, Aluminum Research Laboratories. Formerly with Metallurgical Division, Aluminum Research Laboratories. 1 P. D. Merica, It. G. Waltenberg and H. Scott: Heat Treatment of Duralumin. U. S. Bur. Stds. Sn. Paper 347 (1910). 2 M. Gayler: Constitution and Age-Hardening of Alloys of Aluminum with Copper, Magnesium, and Silicon in the Solid State. Jnl. Inst. Met. (1922) 28, 213. W. Fraenkel: Vergutbare Aluminiumlegiengen. Ztsch. Melallkunde. (1920) 12, 427. E. H. Dix, Jr.: Note on the Microstructure of Aluminum-Iron Alloys of High Purity. Proc. Amer. Soc. Test. Mat. (1925) 26, Pt. 2, 120. E. H. Dix, Jr. and H. H. Richardson: Equilibrium Relations in Aluminum-copper Alloys of High Purity. Trans. A. I. M. E. (1926) 73, 560. E. H. Dix, Jr. and W. D. Keith: Equilibrium Relations in Aluminum-manganese Alloys of High Purity. Proc. Inst. Met. Div., A. I. M. E. (1927) 315. E. H. Dix, Jr. and A. C. Heath, Jr.: Equilibrium Relations in Aluminum-silicon and Aluminum-iron-silicon Alloys of High Purity. Proc. Inst. Met. Div., A. I. M. E. (1928) 164. E. H. Dix, Jr. and F. Keller: Equilibrium Itelations in Aluminum-magnesium Alloys of High Purity. Proc. Inst. Met. Div., A. I. M. E. (1920) 351. E. H. Dix, Jr., F. Keller and R. W. Graham: Equilibrium Relations of Aluminum-magnesium Silicide Alloys of High Purity. Trans. A. I. M. E., Inst. Met. Div. (1931) 404. W. L. Fink and K. R. Van Horn: Constituents of Aluminum-iron-silicon Alloys. Trans. A. I. M. E., Inst. Met. Div. (1931) 383.

Jan 1, 1932

By G. Derge, L. D. Kirkbride

In recent years the problem of sulfur elimination in iron and steel-making has been of increasing importance. This interest has been due to the increasing amounts of sulfur coming into the system via raw materials. As a result, many investigations have been directed at obtaining information pertaining to the rate and mechanism of sulfur removal in the blast furnace as well as measuring appropriate thermodynamic quantities. Chang and Goldmanl as well as others2&apos;3 showed that the process of sulfur transfer from molten carbon-saturated iron to blast furnace-type slags could be considered as two opposing first-order chemical reactions. Recently, Ramachandran et al.4 have shown that during desulfurization electrical neutrality is preserved in both phases and iron and silicon are transferred into the slag concurrently with the evolution of carbon monoxide gas. They concluded that the reaction s + c-+ (0)=(S) + CO(g) does not express the stoichiometry of the sulfur transfer process. As in all previous investigations, these authors studied the process of a net transfer of sulfur from metal to slag across a slag-metal interface. However, no experimental data have previously been obtained for the process of sulfurization. It was the purpose of this study to investigate the sulfurization process, i.e., net transfer of sulfur from slag to metal. EXPERIMENTAL PROCEDURE Apparatus—The equipment used in this investiga-tion was typical of that used by others.1-3The furnace was a high-frequency induction unit powered by a 35 kw Hg spark gap converter. Fig. 1 shows a schematic diagram of the apparatus. A two-compartment crucible assembly was employed to melt the slag and metal charges; being similar to that used by Ramachandran,4 in size and design. The atmosphere was that produced by reaction of hot graphite with air. Temperature measurements were made by W-Mo thermocouples which were calibrated against a Bureau of Standards Pt - Pt 10 pct Rh couple. Temperature control was always good to * 5°C and in general was much better than this figure. Raw materials used in the experiments were C. P. reagent grade where possible. The silica used in the preparation of the slags was in the form of highly purified silica flour. Silicon and titanium additions

Jan 1, 1961

By H. Stuart Auvil

Twelve samples of run-of-oven coke were taken at coke plants in the United States and Canada. Sampling procedure was directed toward obtaining the highest possible degree of uniformity in the gross samples, so that variations in results caused by sampling variations were at a practical minimum. Under these conditions the standard deviation of the screen analysis test on 500-pound samples is found to range from 1.2 percent for the 1-inch screen to 4.5 percent for the 5-inch screen. At present, the A.S.T.H. standard method of test requires that results be reported to the nearest 0.1 percent. This implies a higher than actual degree of precision, and revision of the report required by the method is suggested. Much larger Samples than are generally tested are required to reduce normal testing errors to a point where they are not appreciable fractions of the total variations found in a smoothly operating plant. For example, it is deduced that over 100,000 pounds of coke must be screened to determine if ordinary day-to-day variations in screen analysis have appreciable effects on the performance of a blast furnace.

Jan 1, 1950

By Walter Crafts, D. C. Hilty

The liquidus diagram for the iron field of the Fe-S-O system has been derived experimentally. The solubility of oxygen in molten Fe-S alloys has been measured at several temperatures and found first to decrease slightly and then increase rapidly with increasing sulphur content. IT is well-known that the types, distribution, and amount of inclusions in any given steel are closely allied with the oxygen and sulphur contents of the metal, so that the term "deoxidation" as conventionally applied in steelmaking refers not only to the control of oxygen and oxide inclusions but to collateral modification of sulphide inclusions as well. Inclusions commonly occur in steel as mixtures of oxides and sulphides, sometimes closely associated and sometimes apparently completely divorced. Their effects on the properties of the metal may vary widely depending on their types and distribution as well as on their quantity. The mechanism by which inclusions form, however, and the means for controlling it are exceedingly complex and not well understood. Nevertheless, as described by Benedicts and Lofquist&apos; and by Wentrup&apos; all oxide and sulphide inclusions, excluding mechanically entrained matter, must result from specific modifications of the basic equilibria of the Fe-S-O system. In an investigation of the mechanism of deoxidation and inclusion formation being carried out at the Union Carbide and Carbon Research Laboratories, it became evident that quantitative data for the fundamental Fe-S-O system were essential to a better understanding of the problem. Consequently, the liquidus surface of the portion of the Fe-S-O diagram of interest in steelmaking has been determined, and the solubility of oxygen in liquid iron containing sulphur has been measured. Fe-S-O Diagram The portion of the Fe-S-O diagram of specific interest in steelmaking is the Fe-FeS-FeO corner. Of the contiguous binary diagrams for this partial system, only those for Fe-FeO and Fe-FeS are known with reasonable certainty.3 Several attempts to derive the FeO-FeS diagram have been made, chief among them being the work of Giani as reported by Oberhoffer,4 and, more recently, that of Vogel and Fulling." Although both Giani and Vogel and Fulling published diagrams for the FeO-FeS system, their observations indicated that the oxide component approximated Fe3O4 rather than FeO, so that there is doubt whether the system is truly binary. Benedicts and Lofquist and also Wentrup published qualitative sketches of the ternary diagram based on the assumption that it was of the type described by Marsh for a ternary system in which two of the contiguous binary systems are simple eutectic systems and the third exhibits a solubility gap in the liquid. Apparently, however, the only previous effort to establish the diagram experimentally was that of Vogel and Fülling whose results are reproduced in Fig. 1. Although defining approximately the limits of the miscibility gap and the location of the ternary eutectic, point E in Fig. I, Vogel and Fülling&apos;s diagram must be considered only semiquantitative. It was derived from a limited number of observations mainly along two quasi-binary sections, and the directions of the tie-lines and the location of the critical point, K in Fig. 1, were estimated by computation. Experimental Procedure The experimental technique employed for the present investigation involved melting mixtures of ferrous sulphide and ferric oxide in contact with iron. Since it was considered that in this part of the system the vapor pressures of sulphur and SO, are so low that they would not affect the results significantly, the melting was carried out in a current of argon to sweep out products of any initial re-

Jan 1, 1953

By Paul Wellman

A computer program is presented that may be used to calculate the bare equipment cost of the major processing units for any hot potassium carbonate gas purification system. The program is designed such that, with only minor modifications, it could be used with a variety of computer systems.

Jan 1, 1968

The Institute has set important objectives for 1988 to make the Institute still more purposeful. Precious metals The Second International Symposium on Mining, Extraction, and Processing of Precious Metals will be held in Las Vegas, Nevada, USA, during the 118th TMSAIME Annual Meeting in March 1989. The First International Symposium on Precious Metals.

Jan 1, 1987

By David B. McWhorter

Conventional analyses of seepage through saturated media do not apply when tailings impoundments are located above a partially saturated zone. Three stages of seepage are identified and methods for estimating the seepage rates and duration of each stage, based upon flow in partially saturated and saturated porous media, are demonstrated. The effectiveness of earthen liners is discussed and procedures for estimating the required properties of the porous media are provided.

Jan 1, 1978

By Herbert R. Babitzke

The purpose of this investigation was to optimize the high-temperature properties of columbium and tantalum. Columbium and tantalum were combined with selected alloying elements to achieve solid solution and dispersion strengthening. Fifty-six alloys were evaluated to determine their formability, hardness, strength at elevated temperatures, and oxidation resistance. The following six alloys showed high-temperature strength: [Cb-15Hf-5W-2Zr-4Al-4Ti-2N Cb-15Hf -5W-5Zr Cb-15.3Ti-4.1Zr-13.7Hf Ta-20Hf-4Al Ta-30Hf-4Al Ta-20Hf-5W-4Al] At 1,200° C, the columbium alloys had strength values of 40,000 psi or greater, and the tantalum alloys had strength values from 50,000 to 58,000 psi. For a 2-hour test period at 1,000° C, weight gains of only 9 and 8 mg/cm2, respectively, were observed on oxidation testing of two alloys, Cb-15Hf-5W-2Zr-4Al-4Ti-2N and Ta-20Hf-5W-4Al.

Jan 1, 1968

By H. S. Choi, I. Iwasaki

The effect of temperature as a parameter in ore flotation has not been systematically studied, although for some ores it has been known for many years that selectivity and grade of concentrates can be improved by conditioning or flotation at moderately or substantially elevated temperatures. In 1934 Coghill and Clemmer&apos; stated that "elevated temperature seems to make hard water more tolerable" in soap flotation, and a cursory examination of the literature indicates that some earlier investigators were aware of beneficial results obtained by floating above room or mill-water temperatures. Tartaron,2 Mitchell et aL.,3 and particularly Hamilton et al.&apos; have shown that high pulp temperatures give high recovery and selectivity in soap flotation of fluorite from a variety of gangue minerals. As a result of the work of these and of other investigators, high-temperature flotation has been successfully applied to industrial flotation of fluorite. Falconer" stated: "The use of high temperature conditioning (above 35°C and preferably above 60°C) in connection with the soap flotation of nonsulphide ores, as covered in B. Kalinowski&apos;s French Patent No. 847,-215, Dec. 7, 1938, is claimed to provide more intense activation, better separation of values from gangue, and reduction in quantity of reagents." The various investigations quoted above clearly demonstrate the improvements to be realized by increasing the temperature at which fluorite is floated, and it is surprising that little or no information has been published on systematic investigation of the same method as applied to other ores. The present article describes comparative results obtained at room temperature and at elevated temperatures by otherwise conventional flotation of iron ores, by single-mineral flotation in the Hallimond tube, and by contact-angle measurements. It is not the purpose of this article to evaluate the commercial feasibility of high-temperature flotation of iron ores, although preliminary calculations show that the cost should not be excessive and that the gains to be realized may well outweigh the extra cost of heating the pulp. LABORATORY FLOTATION TESTS Experimental: All flotation tests reported in this article that use a laboratory Fagergren cell were made on ore A (either containing the primary slimes or deslimed at 20µ as specified) following the preparatory procedures described elsewhere- or this particular ore. Ore A contained hematite, goethite (limonite), quartz, chert, and minor quantities of magnetite. Confirmatory tests made on other ores show that the same general principles apply to ores of similar mineralogy and structure. Conditioning was performed by adding the collector, as a soap, to the vigorously stirred and heated pulp. Conditioning time was 5 min, the pulp contained 60 pct solids, and the equivalent of 0.5 Ib of fatty acid was added per ton of original (unde-slimed) ore. The pH of the pulps ranged from 6.8 to 7.1 (25°C measurement) during conditioning. The pH was adjusted in the flotation cell by addition of either NaOH or H2SO4, the values reported being those of the pulp cooled to 25°C. During conditioning and flotation the pulp temperatures were controlled within l° to 2° by immersion of Variac-controlled Calrod elements in the conditioning beaker and in the cell, and by the use of water, heated to the appropriate temperature, for transferring pulp, adjusting pulp volume, and washing. Selectivity indexes have been calculated on the same basis as those reported in the article by Cooke, Iwasaki, and Choi." Results: Table I gives the results obtained by floating deslimed ore A with pure oleic acid at 25" and 50°C, and Fig. 1 shows the selectivity indexes plotted against pH of flotation. Inspection of Table I

Jan 1, 1961