Search Documents

By Charles S. Barrett, L. H. Levenson

Since 1925, when the preferred orientations in compressed aluminum were first determined1,2 the orientations have been described as a fiber texture in which a face diagonal, [110], of the face-centered cubic lattice is parallel to the compression axis. Subsequent experiments have seemed to confirm this texture,3-5 and a number of theories (recently summarized in references 6 and 7) have been proposed to explain it and to relate it to the behavior of single crystals during compression.3,8-11 The experiments reported in this paper prove that the orientations are not adequately described as quoted above—i.e., as a [110] fiber texture—although this is a first approximation to the actual texture. They also show that the texture cannot be thought of as a stable orientati011 that is reached and maintained after a sufficient amount of deformation. The actual texture, when studied in detail at successive stages of compression, indicates that a hitherto unsuspected range of orientations is present, both in the polycrystalline metal as a whole and in various individual grains in its interior, and that a state of dynamic equilibrium exists within this range. The reasons for the failure of previous theories to predict the actual texture become obvious when the heterogeneous nature of the flow is considered. In addition to the deformation texture, the manner of its development, and its theory, this paper presents data on the following related subjects: the identity of strain markings in aluminum; the orientation changes in aluminum single crystals during compression and a comparison of these with the conditions in individual grains of a polycrystalliile specimen; the origin of asterism ill deformed single crystals, which heretofore has been regarded as a distortion localized at the surfaces or slip planes; and the relation of plastic strain in individual grains ill all aggregate to the strain of the whole.

Jan 1, 1940

By Jay R. Burns

Two magnesium sand-casting alloys are commonly favored in the United States. These are referred to as H and C alloys (Dow Chemical Co.) or AM265 and AM260 alloys (American Magnesium Corporation). Both are of an aluminum-zinc-manganese type. H alloy contains 6 per cent aluminum and 3 per cent zinc and is characterized by relatively good toughness. C alloy contains g per cent aluminum and 2 per cent zinc and is employed where high yield strength and pressure tightness are required. Examination of magnesium castings poured in Europe and England,1,2 however, demonstrates that H and C alloys are replaced by A8 and AZ91, respectively. That is, A8 represents a magnesium alloy having superior toughness while AZ91 is suitable for high yield strength and pressure-tight applications. The basic difference between the American and European alloys is that the foreign alloys employ a somewhat higher aluminum content and less zinc than is found in H and C alloys. The mechanical properties of the alloys, when divided into high and low-aluminum groups, are quite similar, as determined from separately cast foundry-control type test bars.3 In this paper the decrease of mechanical properties caused by any given amount of microporosity is measured for H, C, A8, and AZ91 alloys. The relative susceptibility of each of the four alloys to microporosity is also determined. Typical mechanical properties and nominal chemical analyses are reported in Table I. [ ] The apparent similarities between the two alloys in each group have led to considerable discussion as to the relative merits of each of the compositions.2 Popular points for comparison between the alloys have been the relative susceptibility of each of the four alloys to microporosity5 and the effect of this microporosity on their mechanical properties. It is primarily intended, in this paper, to show the

Jan 1, 1946

By D. Argyriades, G. Derge, G. M. Pound

The electrical conductance of molten FeS was studied as a function of temperature and composition. It was found that stoi-chiometric FeS (36.5 pct S) shows a minimum specific conductance of 400 ohm-1 cm-1. For the Fe-rich melts the conductivity increases with increasing amount of iron to about 4850 ohm-1' cm-I at 26 pct sulfur. For the sulfur-rich melts the conductivity increases with increasing amount of sulfur until it reaches a maximum of 1300 ohm1 cm-1 for 37.4 pct S and decreases to 800 ohm-1 cm-1 for 38.3 pct sulfur. It is concluded that molten stoichiometric FeS is an intrinsic semiconductor in which the forbidden gap in the electron energy level diagram is quite narrow. Excess sulfur acts as an acceptor impurity in providing a component of positive hole conduction, while excess iron acts as a donor impurity to increase the n-type conduction. K. Bornemann and G. von Ftauschenplatl used a four-terminal, direct-current cell to study the electrical conductance of molten copper sulfide. Their measurements showed a high conductivity, of the order of 100 ohm-1 cm-" and a positive temperature coefficient. From electrolysis studies, Savelsberg2 concluded that molten Cu2S and molten FeS are electronic conductors. Further. he found that molten FeS has a high specific conductance, of the order of 1500 ohm-' cm-', and a small negative temperature coefficient. Pound, Derge, and Osuch,3 using an ac Kelvin circuit and a four-terminal cell, measured the specific conductance of molten Cu,S, molten FeS, and various mixtures. They found that the specific conductance of the solutions followed a roughly additive rule of mixtures. Yang, Pound, and Derge4 showed from electrolysis measurements that the mechanism of electrical conduction in molten Cu2S, FeS, and mattes is primarily electronic. Further, they observed that small additions of CuCl suppress the electronic conduction whereupon the system behaves ionically.

Jan 1, 1960

By Wayne Loel

THE application of aerial photographs to all phases of geologic mapping is set forth, indicating the advantages to be gained in different types of country and under varying climatic conditions, Methods of field and office procedure are given from a geological point of view, as well as suggestions regarding the best methods of aerial mapping for different uses and under varying field conditions, including the study of submarine geology. Aerial photographs with accompanying geologic maps are shown to illus-trate the appearance from the air of different geologic features under varying climatic and topographic conditions.

Jan 1, 1938

This report presents the comments of members of the Institute's Sub-committee on Physics of Mine Ventilation on the proposals of a special committee of the Institute of Mining Engineers (London). This report is as follows: THEORY OF MINE VENTILATION Abstract of a report submitted June 16, 1925, to the Council of The Institution of Mining Engineers by a Special Committee Laws of Flow of Aib The law of flow of air in mine galleries is, at present, expressed by two formulas differing slightly in shape but both derived from the original hydraulic formulas of Chezy and others. These formulas are: The Atlcinson Formula.—Pa = KsV2, which in transformation becomes a3 where P = pressure producing flow; K = coefficient of friction; s = surface of the mine galleries; V = velocity of flow; Q = rate of flow; a = area of mine galleries. This formula is especially applicable to mine galleries, but is unwieldy in application, as in many problems we are dealing with changes produced in the same set of airways when K, s, and a are assumed not to change, and the only variables are P and Q. Great uncertainty prevails as to the exact values to be assigned to the coefficient K in different types of airway, as different workers have given widely differing values. This formula assumes: (I) That resistance to flow is independent of the pressure within the gallery. (2) That changes in volume within the limits of pressure ordinarily met with may be neglected. (3) That changes in density and viscosity and mode of flow of the air may be neglected. (4) That the coefficient K is a constant. (5) That P is proportional to the square of the velocity. We cannot find any reliable experimental work leading us to conclude how far these assumptions are justifiable in mining practice. Equivalent Orifice Formula.—The fundamental form of this formula is Q = ~nA.\/2~11

Jan 1, 1927

By D. J. Carpenter

Safe and successful mine closure represents a fundamental work element that needs to accommodate the geochemical conditions existing at the completion of the mining and ore processing effort. Given the interests in limiting costs and time associated with mine closure efforts enhanced prior understanding of the geochemical conditions likely to exist upon exhaustion of the economic reserves can provide important benefits. The purpose of this paper is to document the benefits associated with geochemical modeling and understanding how the ore formation process may impact mine closure efforts, using one ore deposit type as an example. Specifically, this paper will emphasize the geochemical processes leading to the formation of sandstone-hosted uranium roll-type deposits and how the resultant concentrations and distributions of ore and gangue phases need to be incorporated into understanding the geochemical conditions projected to exist at the end of mineral recovery efforts. The paper will describe the evolution of geochemical conditions leading to ore body formation and the geochemical effects induced by open pit mining and how these may be used to understand both the geochemical controls and constraints on residual mine water. In addition, a discussion will be provided on how these conditions may be simulated by solution equilibria and kinetic modeling to develop optimum approaches to achieve applicable closure standards. This paper will also discuss specific augmentations to existing industry standard solution equilibria and kinetic models and associated thermodynamic databases to maximize the predictive accuracy of the geochemical modeling results. The benefits of understanding the electrochemically reactive behavior of uranium and associated gangue phases and incorporating this behavior into mine closure efforts will be presented. The culmination of the benefits of the geochemical modeling will ultimately be the development of a sustainable approach to uranium mine closure that is based upon an engineered environment designed to return the ore body to stable geochemical conditions.

Feb 27, 2013

By H. P. Greenwald

THIs paper brings forward a discussion that was prepared for the meeting of the Coal Division in Chicago in 1938.1 War in Europe less than a year after that meeting, followed by our defense preparations and entry into the conflict, caused general cessation of large-scale experimentation on the subject, and it is best to confine this paper to events in the United States during the five-year period since the preceding paper was written. The views of members of the Coal Division's Committee2 on Rock-dust-ing for 1943 were obtained before this paper was written and the manuscript was reviewed by them. Extent of Rock-dusting Statistics on the use of rock dust in the United States during the years 1930-1933, appearing on page 97 of Volume 139 of the Transactions are extended in Table I herein through the year 1941. The results through 1933 did not appear encouraging, but there has been improve-ment since that date. It has always been true that the larger operations were the ones that used rock dust. In 1941 only 10 per cent of the mines in the country used rock dust, but they produced 57 per cent of the coal, employed just under 50 per cent of the miners, and accounted for 52 per cent of the man-hours. Unfortunately, collection and compilation of these statistics are slow procedures, and figures dealing with the tremendous war expansion of the industry are not likely to be available for a year or more. In 1941 the five leading states in regard to percentage of man-hours worked in mines using rock dust were: Utah, 92.1; Wyoming, 79.3; Alabama, 77.4; New Mexico, 72.5; West Virginia, 65.3. The first four states were the same as in 1933, but West Virginia displaced Washington in fifth place. On the basis of pounds of rock dust used per ton of coal, the five leading states in

Jan 1, 1944

By H. P. Greenwald

THIs paper brings forward a discussion that was prepared for the meeting of the Coal Division in Chicago in 1938.1 War in Europe less than a year after that meeting, followed by our defense preparations and entry into the conflict, caused general cessation of large-scale experimentation on the subject, and it is best to confine this paper to events in the United States during the five-year period since the preceding paper was written. The views of members of the Coal Division's Committee2 on Rock-dust-ing for 1943 were obtained before this paper was written and the manuscript was reviewed by them. Extent of Rock-dusting Statistics on the use of rock dust in the United States during the years 1930-1933, appearing on page 97 of Volume 139 of the Transactions are extended in Table I herein through the year 1941. The results through 1933 did not appear encouraging, but there has been improve-ment since that date. It has always been true that the larger operations were the ones that used rock dust. In 1941 only 10 per cent of the mines in the country used rock dust, but they produced 57 per cent of the coal, employed just under 50 per cent of the miners, and accounted for 52 per cent of the man-hours. Unfortunately, collection and compilation of these statistics are slow procedures, and figures dealing with the tremendous war expansion of the industry are not likely to be available for a year or more. In 1941 the five leading states in regard to percentage of man-hours worked in mines using rock dust were: Utah, 92.1; Wyoming, 79.3; Alabama, 77.4; New Mexico, 72.5; West Virginia, 65.3. The first four states were the same as in 1933, but West Virginia displaced Washington in fifth place. On the basis of pounds of rock dust used per ton of coal, the five leading states in

Jan 1, 1944

By J. P. Wilson, T. Cook, H. Kling

The Tessenderlo-Kerley Leachprocess has been shown to be effective in the removal of residual copper from molybdenite concentrates. Concentrates of varying mineralogy, including those containing relatively large amounts of chalcopyrite, have been successfully leached on laboratory and pilot plant scales. The lixiviant system is ammonia andammonium bisulfite with air / oxygen addition. An abrasive is added which greatly enhances the kinetics, and it is subsequently screened out and reused. The dissolved copper is easily recovered using existing technology. Extraction profiles, reagent consumptions, and mineralogical data are presented.

Jan 1, 1999

By F. A. Myzenkov

The technology developed by the authors uses new methods for raw material smelting in electric furnaces, a new autogenous method and apparatus for subliming smelting for antimony trioxide production and separation of antimony and gold. Concentrate produced from the ore deposits in Yakutia has the following average contents of main constituents, % by weight: 29.4 Sb, 1.2 Fe, 13.1 S, 40.0 SiO2, 0.2 As, 2.6 CaO and 45 g/t of Au. Unlike the technology used abroad a new autogenous method makes it possible to increase considerably specific capacity and reduce gold losses with antimony trioxide by several times. At the same time mineralogical composition of trioxide has improved considerably ? it has mainly a cubic base with prevalence of senarmontite. The content of a main component (Sb2O3) in the final product has increased from 99.0% up to 99.6% which means better quality and makes it suitable for use in special technologies. Despite a lower antimony content of the concentrate (29.4% as compared with over 33% as common in the world practice), an antimony recovery of 85.3% into a commercial-grade product has been achieved, as well as a gold recovery of 96.65% into a gold-antimony alloy. The technology for processing gold-antimony materials developed and introduced at the Ryaztsvetmet plant is unique in the world with respect to gold recoveries.

Jan 1, 2006

Underground mine planning is characterised by a series of designs, starting with prefeasibility and culminating in operational. Information on the mineralisation and geotechnical conditions is available in increasing levels of detail, as development occurs. In the recently completed AMIRA Planning and Rapid Integrated Mine Optimisation (PRIMO) project, a methodology for producing good strategic and then tactical designs using new optimisation tools, was developed. At the strategic level, fundamental decisions must be made such as those relating to cut-off grade, bench heights, mining methods, access and haulage systems, properties of the mill, etc. The inputs are the block and financial models, geotechnical data, infrastructure and production costs, etc. Stope definition for strategic designs includes bench RLs (relative levels), orebody envelopes, and design and placement of amalgamated or simplified stopes. If multiple mining methods are under consideration, then stopes need to be associated with these. Access design must take into account decisions such as declines versus shafts, a template for level layouts and the topology of the access network. Some of the geotechnical and physical constraints are relaxed for strategic design stages. Strategic scheduling is high level, from a month to a year at a time. In the PRIMO project, software tools have been developed enabling the mine planner to rapidly produce a large number of such strategic designs. After the designs have been evaluated, the highest value designs are chosen and a small number of these can then be further refined at a tactical level. For these designs, the first step is determination of all stopes meeting physical and geotechnical requirements and constraints, allowing for complex stope shapes. Next, detailed layout of the mine access network is obtained, satisfying all operational and geotechnical constraints. Finally, more detailed scheduling is performed, over shorter time periods. The Melbourne University group has focused on optimal access design. In particular, the access network is optimised for minimum cost, taking into account the cost of haulage and development over the lifetime of the mine. Costs vary over the different parts of the network depending on the quantity of haulage and so a weighted network optimisation problem has to be solved. We have developed two software tools for this task, decline optimisation tool (DOT) and planar underground network optimiser (PUNO). DOT produces an optimal network of declines and crosscuts connecting access points on the levels to a portal or break-out point from existing infrastructure. PUNO designs the level layout, including footwall and hanging wall drives, development drives and connections to vent raises. A survey will be given of the capabilities of DOT and PUNO when used on some recent case studies. Our current goals include incorporating some aspects of ventilation design and modelling the development costs when additional ground support is required. This is an abstract only. A full paper was not prepared for this abstract.

Dec 6, 2010

By Emil-Paul Lorenz

Considered as a whole, the mineral resources of the Turkish Republic (Anatolia) are in their untapped virgin state, and the little development shown is not the result of modern systematic geologic exploration but the continuation of the ancient open-pit mining methods of the Orient. When I came to Turkey in 1924, I found myself confronted by a formidable task because of the lack of preliminary geologic mapping. Today this condition has not essentially changed; less than one per cent of the country is covered by topographic mapping adequate for modern requirements. However, I was able to bring a semblance of order in a presentation of the mineral deposits of this country, by tracing the story of the mineral deposits that showed surface evidence of their existence. At present only the easily discovered mineral deposits of coal, copper, and lead-silver ores are being exploited. In the case of coal, of 3,000,000,000 metric tons available, only 100,000,000 have been mined. The same is also true for copper, lead-silver, and other ores, as shown in Table 1.

Jan 1, 1948

In this very interesting paper, Mr. Harrington mentions a considerable variety of materials suitable for use in the rock dusting of coal mines; this suggests that you may possibly be interested in same purely theoretical figures tending to show the superiority of gypsum for this purpose. Some of the gentlemen present have found difficulty in applying a thick, adherent coating of dry gypsum to the ribs and roofs of their workings, for which reason pulverized gypsum will perhaps be chiefly useful for the loading of barrier troughs. In view of the function that rock dust is expected to perform in case of a coal-dust explosion, it seems obvious that the most efficacious dust will be the one that can absorb the most heat and absorb it most rapidly. The customary rock dusting materials differ considerably in this respect, depending principally upon the facility with which they can be decomposed at the temperatures encountered in a coal-dust explosion. Such stable materials as silica, anhydrite and flue-dust vary but slightly in their heat-absorbing capacities, the specific heats of minerals in general ranging between 0.19 and 0.22; on the other hand, gypsum and limestone, as well as certain argillaceous materials such as shale, adobe, etc., are capable of absorbing additional heat through their chemical dissociation, although, as will appear later, it is questionable whether the amount of heat thus absorbed, in the case of limestone, shale, and adobe, is large enough to have any practical value. As to the temperature developed by a coal-dust explosion, the Bureau of Mines reports one test in which gold foil was melted, and others in which silver foil was melted, but not gold; hence 1832° F. (1000° C.) seems a reasonable figure to assume for purposes of calculation. Normal temperature is taken as 68° F. (20°C.). The other fundamental data required for the computations as cited by various authorities, are as follows: [Specific heats Gypsum : 0.259 Calcium sulphate, anhydrous. . .190 Limestone 0.216 Lime 0.239 Clay, shale, silica, etc. usually not exceeding 0.220 Carbon dioxide .:0.217 Steam (at atmospheric pressure)0.500 Heats of formation CaSO4+2H2O-4.606 Kg-cal. per gram molecule, or 48.2 B:t:u.' per pound of gypsum.- CaO +C0,42.5 Kg.-cal. per gram molecule, or 765 B.t.u. per pound of limestone. Latent heat of vaporization of water. from and at 100°C.. 535.9 Kg.-cal. per kilogram (964.6 B.t.u. per pound).] Computations will be based on the Fahrenheit scale and British thermal units, as probably more familiar in the coal industry. First as to the inert materials: their heat-absorbing capacity per pound is simply the product of their specific heat, say 0.22, multiplied by the assumed rise in temperature, 1764° F., or 388 B.t.u. per pound. Gypsum, CaS0, 2H.0, though apparently perfectly dry, contains 21% of combined water. When gradually heated it will have liberated three-quarters of its water freely by the time it reaches 250° F.; the remaining one-quarter is retained to a somewhat higher temperature, but the last of it will have been expelled at 482° F. For calculating the total heat absorbed in raising gypsum (or its products) to the temperature of a coal-dust explosion, no serious error will be intro-

Jan 1, 1925

By P. Valicek, M. Farren, R. G. B. Pickering, G. Harrison, P. van Dorssen, W. Joubert, H. J. van Rensburg

Introduction In South African metalliferous mines, stoping operations are largely confined to narrow, tabular orebodies making mechanization extremely difficult. Limited flexibility in terms of stope width has necessitated drilling by means of hand held, pneumatic rock drills at most of our operations. As the largest producer of platinum in the world, we drill in excess of forty million stope blast holes per annum. Cleaning of the broken ore is also done by conventional means—utilizing scrapers and scraper winches. Conventional methods such as these carry high costs in terms of risk exposure as well as labour intensity. The purpose of this paper is to describe the development of a long hole stoping system suitable for the narrow platinum reefs. The new system had to be substantially safer and more cost effective than conventional mining. We selected a site that was conducive to mechanized mining and set out the parameters that we considered would meet our requirements. We then conducted a feasibility study to evaluate the conceptualized long hole stoping system in terms of specific goals. An analysis of the proposed system identified the Key Performance Indicators (KPIs). One of the most critical goals was to be able to create a man-freestope. This would mitigate the safety risk associated with normal stoping operations, as well as the inefficiency cost previously referred to. Other challenges included setting targets for long hole accuracy, stoping width reduction and specific blasting system performance for long hole stoping. We also modelled a critical span that we considered to be inherently safe and to ensure hangingwall stability, throw-blastcleaning and overall system productivity. Anglo Platinum Research and Development and Sandvik Tamrock entered into an agreement for the supply of a specialized long hole-drilling machine. The system was implemented and tested by the mine with the support of the other participants. The results achieved met our expectations. It was demonstrated that with this method of mining it is possible to have a man-free/support-free stope face and to achieve a reduction in shaft head cost per ton whilst reducing dilution. Key performance indicators assessed during the trial •Safety targets •Mining layout •Drill rig •Production targets •Support requirement •Explosives requirement •Services requirement •Ore removal and cleaning requirement •Training requirement Safety targets All persons involved with the project had to adhere to the mine’s safety programme including the zero-tolerance campaign, and were required to report all hazards observed immediately. Mine personnel and Tamrock carried out a full risk assessment on the drill rig before transporting underground. A further risk assessment was carried out when the machine was in position underground. Mining layout See Figure 1 and Figure 2 for a detailed description. Drill rig The drill rig was a combination of a Secoma P-Low LC 10long hole feed and an Axera low profile carrier. The choice of this equipment was made through consultation with Tamrock Sandvik. All relevant design perimeters of the area to be mined were taken into consideration. Production targets

Sep 1, 2001

By P. J. Potter

Practically all tin-base babbitt metals used in engine bearings are made to customers' specifications, which are many and varied. The copper ranges from 3 to 8 per cent. and the antimony from 4 to 13 per cent.; generally, the babbitt with lower copper content will contain from 4 to 8 per cent. antimony and that with higher copper will have from 7 to 13 per cent. antimony. The allowable lead content varies from 0.20 to 2.00 per cent. If a solder is used as a bonding material instead of tin, the resulting material in the finished bearing will have a higher lead content, but it would not be enough to bring the lead above specifica-tional limits. Impurities such as iron, arsenic and bismuth should be determined in the tin before using to insure a uniform and high-grade product. These points must be considered when segregating and grading the waste that comes from the finishing operations on lined bearings. Classification of SCRAP Because of the extremely rigid nature of most of the specifications for bearing linings it is necessary to use the purest of materials as a base for all compositions. The problem of handling secondary metals is confined almost entirely to the recovery of drosses, spills and turnings incident to the manufacturing operations. As a matter of convenience the waste or scrap may be divided into 10 grades, as follows: 1. Tin from pots where tinning operation is carried out. 2. Tin and babbitt spatters from babbitting operation. - 3. Tin skimmings combined with burned zinc chloride. 4. Borings and reamings. 5. Gates from die-cast bushings and bearings. 6. Drosses from die-cast pots, babbitt foundry pots, and pots in babbittiug room. 7. Babbitt with small amount of bronze from machining operations. 8. Babbitt and bronze borings. 9. Scrap bronze-back babbitt-lined bearings. I 10. Scrap die-cast bearings and bushings. A few of these grades of salvaged material have compositions that make it possible to determine beforehand where they may be used to

Jan 1, 1930

By J. W. Thompson

The term "minerals" when employed in a conveyance in the State of West Virginia is understood to include every inorganic substance which can be extracted from the earth for profit, whether it be solid, as rock, fire clay, the various metals and coal, or liquid, such as salt, and other mineral waters and petroleum oil and gas. Horse Creek Land & Mining Co. v. Midkiff (West Virginia), 95 Southeastern 26, p. 27. TERM INCLUDES OIL AND OAS. The term "minerals" used to describe the interest in land granted or reserved bona fide includes petroleum oil and natural gas. Horse Creek Land & Mining Co. v. Midkiff (West Virginia), 95 Southeastern 26, p. 27. INJUNCTION TO PREVENT RElllOVAL. The removal of ore from the premises of another without his consent will be enjoined. Barnes v. Esch (Oregon), 169 Pacific, 512, p. 518. TITLE TO MEXICAN BULLION-JURISDICTION OF FEDERAL COURTS TO DETERMINE. Where bullion within the jurisdiction of the Mexican Government was seized, condemned, and sold for war supplies by the Constitutionalist forces in the revolution acting under authority from Gen. Carranza, claiming to be the provisional President of the Republic of Mexico, a United States district court of Texas, into which State the bullion has been imported from Mexico, has jurisdiction to try and adjudge as to the validity of the title acquired by and through the seizure, appropriation, and sale by the Carranza forces as against an American citizen claiming ownership of such bullion prior to its seizure.

Jan 1, 1919

By Roussey Roussev

The use of chemical additives on grinding is of significant importance considering the high energy consumption of grinding processes. My research indicates that the dispersant approach explains the effects, in this particular case of wet grinding. Further, the dispersant approach combined with torque measurements give the possibility of clarifying the mechanisms involved when using grinding aids. I find the conclusions derived from the data obtained to be correct and useful for grinding. In general, I agree with the explanations. However, I would like to discuss several additional points that I consider to be important, and in the same time to mention some of my own results from investigations similar to those presented in the study under discussion. The "bed volume concept" and the change of slurry viscosity explain adequately the data plotted on [fig. 3], in conjunction with [Figs. 1 and 2]. However, the significant increase of the average torque in the case of 83% solid with XFS-4272 introduces the necessity of establishing the optimum of percent solid when dispersant is used. For example, the optimum percent of solid for different materials varies. One of the reasons is the material's mass density. On the other hand, it is necessary to determine the concentration of the chemical used. Because of this, it would be interesting to know how the cited concentration was selected.

Jan 1, 1983

By William Escudero

El presente trabajo describe el planeamiento estratégico para el sostenimiento de la sociedad minera El Brocal a través de la gestión en el trabajo organizacional. Su principal objetivo es aumentar la productividad y la reducción de costos de minado y la planta concentradora. Para ello, se tomó el modelo de planeamiento estratégico desarrollado por Fred David y se realiza el análisis y diagnóstico interno de la empresa, a partir de los antecedentes, situación actual de la empresa, evaluación de la misión, objetivos actuales y cadena de valor de la empresa, luego se clasifica a la industria minera y se integra los resultados obtenidos, la matriz de evaluación del factor externo (EFE) y la matriz de evaluación del factor interno (EFI); para así elaborar la matriz (FODA) a partir de la cual se formula as estrategias por seguir. Finalmente, se redefine la misión de futura de SMEB y se ejecuta las estrategias y las acciones en las áreas funcionales.

Sep 13, 2001

By F. S. McNicholas

IN the writer's opinion the term "block caving" has been rather loosely applied to a general principle of mining, and therefore detailed classification of caving methods and draw, together with the characteristics required for each method, will fill a desired need. Selection of caving method should be made only after a study of all governing conditions, such as size of orebody, lateral and vertical extent of ore-body, attitude, treatment demands, possible resultant pressures, and cost and profit comparison of methods. Successful caving methods can be classified under six main headings: (1) Full-protected block caving, (2) semi-protected block caving, (3) unprotected block caving, (4) full-panel caving, (5) half block-panel caving, (6) block-panel caving. The methods and factors governing choice of method are shown in Table I. Full-protected Block Caving Full-protected block caving consists of develop-ing, undercutting, and drawing to exhaustion a block of ore of predetermined size without coordination of mining or draw with adjoining areas. The block is mined and drawn as an independent unit (Fig. 1). Full-protected block caving demands that mining and draw cannot be done against unconsolidated capping in adjoining caved and exhausted blocks. Two sides of block are against solid. Caved capping must be allowed to consolidate for a suitable period, usually not less than one year. Pillars may be left in lieu of consolidated capping (Fig. 2). The advantages of full-protected block, caving are: (1) A definite area is developed, mined, and drawn as a unit so that all work may be completed, the block drawn to exhaustion in the minimum length of time, and the area then abandoned. (? Production is not restrained because of coordina1, on with adjoining areas. (3) Records of draw and caved reserve of ore are good. Upon abanwnment of the block, accountability for production is closed out with no carry-over to adjoining areas. The disadvantages of full-protected block caving are: (1) Side dilution from the draw adjacent to the consolidated capping may be serious, particularly where capping does not consolidate sufficiently in the allotted time. (2) Boundary weakening is needed on the solid sides of the block except in weak rocks. (3) Maximum cantilever and compression effect to aid caving and fragmentation may not be secured since the draw should proceed from the solid to the consolidated capping to minimize side dilution. However, undercutting from the loose (caved capping) to the solid with a slight initial draw in the same manner will develop cantilever effect. (4) A period of at least one year, more is usually desirable, must be allowed for caved capping ,to consolidate before mining the adjoining block, depending upon the characteristics of the capping. (5) Capping may not consolidate sufficiently in the time that can be allowed. Full-protected block caving is indicated where: (1) The ground is weak and heavy and workings

Jan 1, 1952

By Charles Austin

IN a recent paper the authors1 discussed the reactions to tempering of hypereutectoid steels quenched from 1000° C., as revealed by studies on changes in hardness, electrical resistivity, coercive force and metallo-graphic characteristics. The data, which related specifically to temper-ing temperatures of 550°, 650° and 710° C., for varying periods up to 125 hr., permitted the following important conclusions: 1. The rate of softening of the steels at the temperatures examined differed markedly although the steels were of "similar" general chemi-cal composition. 2. The temperature of maximum softening spread over a range from about 650° C. to the eutectoid inversion. 3. The divergence in behavior was ascribed, at least in part, to a profound difference in tendency to graphitization on annealing at sub-eutectoid temperatures. 4. The mode of spheroidization of the cementite, as revealed by metallographic studies, also varied considerably in the different steels. The purpose of the present investigation is to pursue further the study of the difference in behavior of the steels on tempering over a wider range of temperature. To this end the following features have received particular attention: 1. Comparison of temperatures of maximum softening of the various steels when the quenched samples were tempered for 5 hr. and for 75 hr. followed by furnace cooling and by quenching in water. 2. Determination of the effect of quenching temperature, prior to tempering, on the rate of softening. Quenching temperatures of 1000° and 850° C. were used in the investigations. 3. Examination of the microstructures obtained with the various heat-treatments employed.

Jan 1, 1938