Search Documents

By Xuewei Lv, Guibao Qiu, Jiaqing Yin, Chenguang Bai

"The iron ore sinter is one of the main raw materials for the blast furnace (BF) process. In the production of iron ore sinter, the cooling speed of the sinter determines its quality. In addition, the heat recovery devices are installed in the cooling machine for energy saving. The cooling parameters like gas flow rate and the size of sinter should be optimized for getting the gas with a higher temperature and a good quality of sinter simultaneously. In this study, the commercial simulation software COMSOL was used to establish a model for simulating the cooling process of the iron ore sinter. Moreover, three different gas flow rate (1.5, 3, 5m/s) and three different diameter of sintered particles (50, 70, 100mm) were investigated with the model. As a result, in certain porosity, a higher cooling speed was achieved when smaller size or larger gas flow rate was used. And lower gas flow rate was beneficial for the heat recovery. The model could intuitively present the exchange of heat between the sinters and air, as well as the flow and temperature fields during the cooling process.IntroductionIron ore sinter plays a great role in iron and steel industry for many Asian countries such as China, Japan and India. As a part of the sintering procedure, the impact of cooling process on the quality of iron ore sinter couldn't be neglected. On the other hand, the massive iron ore sinters which were at high temperature contain extremely large amount of heat. However, it was reported that there's very few of them recovered in China with an average recovery rate of nearly 10.5% at 2004 [1]. Thus, more reasonable cooling procedure should be developed to get high quality product and heat recovery rate simultaneously."

Jan 1, 2011

By Eiji Kojima

In this research, dynamic and static load tests were performed on permanent foundation piles which had a pile length of 30 m, 800 mm in outer diameter and 15 mm in wall thickness. In this site the dynamic horizontal load test on a smaller test pile, 12 m in length, 500 mm in outer diameter and 12 mm in wall thickness, was also carried out. The static horizontal load versus horizontal displacement derived from the dynamic load test conformed well to that measured in the conventional static horizontal load test of the pile with 800 mm diameter. Then an attempt was made to predict the horizontal load displacement of the pile with 800 mm diameter based on the results of the dynamic horizontal load test of the pile with smaller diameter of 500 mm.

Jan 1, 2006

Adsorption Effect on Multi-Heavy Metal Ions in Wastewater by Water-Washing Waste Saccharomyces cerevisiae

Sep 13, 2010

By Verónica Rueda

El proceso de explotación de la Minera Rayrock se inició hace seis años a tajo abierto y ahora comprende las etapas de extracción del mineral, chancado, aglomeración, lixiviación, extracción por solventes y electro-obtención. En ese sentido, el presente trabajo describe el avance del proceso de extracción en el proyecto minero Ivan, perteneciente al yacimiento de la minera Rayrock a través de las técnicas de lixiviación de minerales oxidados y sulfurados de cobre y del manejo innovador en las operaciones de extracción por solventes y electro-obtención.

Sep 13, 2001

Mine drainage and mine reclamation are topics of major interest to the mining industry, federal and local governments, and the general public. This publication and its companion three volumes are the proceedings of a conference held in Pittsburgh, Pennsylvania, April 24-29, 1994. There were twelve sessions (69 papers) that dealt with mine drainage, including modeling, geochemistry, prediction, treatment, control strategies, characterization, hydrology, and case studies. These sessions comprise volumes 1 and 2. The six sessions (34 papers) that dealt with reclamation and revegetation of disturbed lands are included in volume 3. Volume 4 includes the six sessions (34 papers) that dealt with such topical issues as fires at abandoned mine sites, subsidence, hydrology, mine wastes, and policy. Poster session presentations are represented by 49 papers and 92 abstracts that have been placed in the back of volumes 2, 3, and 4, consistent with the subject of that volume.

Jan 1, 1994

Thermodynamics of Non-Cyanide Gold Solvents The present status of the raw material base in the gold industry requires specific ways to recover gold and silver from ores. Most gold is closely associated with sulfides which require flotation followed by pressure or bacterial oxidation. The next stages of processing usually require using expensive operations for the preparation of leaching. A lot of researchers want to find a new alternative solvent for the extraction of precious metals from these products. According to the authors, one of the best ways is to use sulfur-based solvents (thiosulfate, sulfite, and their various mixtures). Thermodynamics of gold and silver thiosulfate dilution are calculated for conditions: the concentration of Au - 200 mg/L, oxygen - 3.2 mg/L, thiosulfate - 79 mg/L, OH- - 170 mg/L. the general result is the possibility of process remains under standard conditions. (erAu = = 0.035 V, ?G298 = - 29.18 kJ/g-atom ??). Silver with thiosulfate forms two strong complexes: [AgS203]- and [Ag(S203)2]3-. ?G0 = -1027 kJ/mol. The complex [AgS203]- is less stable: ?G0 = 486 kJ/mol. It should be noted that despite the high stability of gold complexes, the sodium thiosulfate may decompose to sulfite and elemental sulfur during the process, especially when heating. Gold is slightly soluble in the sodium sulfite solution, however it forms the strong complex [Au(SO3)2]3-. Depending on the concentration of free S2O32-ions, silver with sodium sulfite forms three complexes: [AgSO3]-, [Ag(SO3)2]3- and [Ag(SO3)3]5-. The dissolution speed of gold in sodium sulfite solution may be in the same range as it is during cyanidation. In this case, a practical application of sulfite process can be also used, especially for the products containing free elemental sulfur. In conclusion, sulfite-thiosulfate gold lixiviants can be used for concentrates after pressure oxidation of the cakes.

Sep 13, 2010

By D. C. Kaliampakos, A. G. Benardos

The existence of quarries near or even within the boundaries of urban centres is the cause of many environmental problems, despite their significant contribution to the cities’ development. Hence, the question arises as to how quarrying activities can be compromised within the spirit of sustainable development in big cities. In the case of Athens, two dominant, though opposite opinions have been formed. The first argues that all quarries must be forced to suspend their activities as soon as possible; the second presses for the continuation of quarrying. Consequently, the question is transposed on the dilemma between improved environmental conditions and economic development. This paper demonstrates that if a complete redesign is employed to specific, nonvisible quarrying sites, the continuation of quarrying activities is acceptable. It is a good compromise between the economical demand and environmental protection.

Jan 1, 2000

By B. G. Cousins, B. O’Rourke, C. Spence

"Some non-flotation chemistries are added to flotation circuits directly and indirectly to control issues such as scaling and dust. Since the dosage levels are generally not very large, a standard laboratory float test may not be able to determine the effect a specific chemical has on the productivity of the flotation circuit. Hudbay and Ashland Water Technologies developed a laboratory testing protocol that uses kinetic float studies to test the effect of normal to extreme doses of antiscalant and dust chemistries (5 ppm to 500 ppm). Laboratory results indicate that this protocol helps to predict the potential interference that a particular chemistry will have on the flotation circuit.INTRODUCTIONFrom a chemical perspective, flotation is a very complex system involving more than the reagents used for flotation. Along with collectors, frothers, modifiers, suppressants and activators, there can be antiscalants for water treatment, dust suppressants used in the mining process, residual flocculants from recycled thickener overflows, grinding aids, and many other types of chemicals that are added upstream of a flotation circuit. Although these other chemicals are usually used at very low doses, it is important to know if they affect the flotation process detrimentally in the event of a spill or a build up from recycled water.Laboratory flotation testing of these chemicals characterizes their effects, but testing at expected doses in the float can mask the effects of the chemicals in the plant. Also, simple tests that do not measure the kinetics of flotation do not reveal the effects the other chemicals have on the flotation circuit. Thus, a new flotation protocol was needed to expose the full effects of chemical additives and to assist in choosing the chemical with the lowest potential for a negative effect.FLOTATION KINETICSMeasuring recovery kinetics in a laboratory flotation cell is a well-established procedure: analyzing concentrates taken in a timed sequence to determine the recovery rate of individual cells in a flotation circuit. The recovery from the early flotation cells are a true measurement of how well a flotation chemical is performing. The principles of kinetics can be mathematically determined by the following functions (Houston, 2006):"

Jan 1, 2013

By Purushottam Kumar

Keywords: Magnetostriction, magnetic properties, Pd(Fe,Co,Ni) single crystals Fe-Pd, Co-Pd and Ni-Pd alloy systems show appreciable magnetostrictive strains that are of interest for sensor applications. These systems exhibit congruent melting minima. In this work the magnetic and magnetostrictive behavior of congruent melting Fe-Pd, Co-Pd, and Ni-Pd compositions have been examined. The alloys examined include Fe-54.9 at.-% Pd, Ni-45.4 at.-% Pd, and Co-45 at.-% Pd. The paper describes the growth of bulk single crystals of these alloys using Czochralski technique. X-ray diffractometer was used to obtain rocking curves that were used to determine the [001] crystal direction. Magnetostriction in [001] direction was measured using strain gages. Magnetic properties were measured using a vibrating sample magnetometer. Ni-Pd showed the highest magnetostriction values among the congruent melting compositions. Magnetic and magnetostrictive behaviors of these alloy single crystals are presented.

Jan 1, 2005

By H. E. Lee, D. Ingvoldstad

AT Bunker Hill the original charge storage and preparation system was installed in 1917 to accommodate lead-silver gravity mill products. Only minor tonnages of wet fines such as vanner and flotation concentrates were received. Charge flux and diluent requirements were provided by an ample supply of siderite middlings and coarse lime-rock. While oversize material was crushed through %-in., the use of roll crushers in series resulted in a more or less granular, free-running charge of adequate porosity. Under such conditions, receipts could be proportioned directly from receiving bins, and suitable blending was obtained by passing the resultant layered composite through a small Stedman disintegrator. This elementary system served well for production and smelting of an extremely lead-rich sinter, in the low column blast furnace. Here sinter physical quality is less critical, and appreciable quantities of raw flux and oxidized ore may be charged directly to the blast furnace without seriously impairing furnace capacity. Prior to 1938 the relative proportions of zinc receipts were low and extraneous flux requirements at a minimum. However, subsequent war-inflated zinc demands brought marked increase in fine concentrate and slimy zinc leach residue receipts and an abrupt introduction to smelting a more refractory zinciferous charge. The higher temperature demands of the more refractory zinciferous charge required a higher smelting column and the higher column, in turn, rendered the blast furnace less receptive to improperly prepared feed. Inadequate presinter processing facilities prevented the production of acceptable sinter, and blast furnace production declined to 50 pct of former capacity. In view of a prevailing contention among lead metallurgists as to the deleterious action of high zinc slag on blast furnace capacity, it was natural to overstress this factor and to concentrate on possible changes in furnace design. Another interpretation was that primary correction should be sought through expanded sintering facilities. This divergence of opinion, together with the extreme material shortages of the 1940's, delayed corrective

Jan 1, 1957

By M. D. Khattar

The paper describes the salient construction features of the Pile foundation work for the Railway viaducts in Algeria. Six viaducts were constructed for execution of the Railway line between Aintemouchent and Benisaf in Algeria. The work was executed by the Indian Railway Construction Company Limited of India (IRCON) for the Algerian National Railways (S.N.T.F.). These six viaducts had multiple spans of 36M resting on hollow piers of heights upto 69M. Most of the piers were founded on piles of 1 and 1.2M dia bored piles going upto 22M deep through cal­careous rocks and were designed for Railway loading in seismically active area. The work involved 356 piles & constituted a very important aspect of the whole work. The concrete in the piles was made with sulphate resistant cement and the integrity of the concrete was tested with Sonic method so as to ensure the quality. The piles were driven with the help of a hydraulic oscillator and the concrete was laid with a tremie pipe. Problems as encountered during execution have been explained.

Jan 1, 1989

By G. Kang

The ferroalloys industry has generated historically substantial solid waste. The accumulated waste causes serious problems to the environment. However, it is possible to transform the solid waste into an environment-friendly resource to serve the human being. Consequently, the construction of plants that are ?environment-friendly? and that accommodate ?recycling? has become a target of most ferroalloy producers in the world to ensure sustainable development. This paper introduces the practice of Shanxi Jiaocheng Yiwang Ferroalloys Works, the biggest manganese metal producer in China, in the development of an ?environment-friendly and recycling? process. The process includes power generation using coal gangue, waste from local coal mines; hollow bricks manufacture using slag and fly ash from the power station; cement production using slag from ferroalloy smelting; recovery of ferrous and non-ferrous elements in the dust from the furnace gas cleaning system; application of silica dust in construction and so on. The final objective of the plant is to realize zero discharge of solid waste. The profit of the ?environment-friendly and recycling? process compensates in part for the operational expense of the environment facilities.

Jan 1, 2004

By V. I. Lakshmanan, Dan A. Mackie

Traditional vat leaching methods have had limited success, primarily due to the high cost of loading and unloading the vats. In general, such batch methods are labor-intensive and costly. Heap leaching has emerged as a viable, low- cost alternative, but low recoveries, normally in the 70% range, offer opportunities for improvement. Also increased regulatory guidlelines for effluent and spent heap leach pads disposal offer potential for alternative methods. The Mackie Vat Leaching Jig (MVLJ) has had its incubation at Ortech International, where bench scale through pilot scale testing continues. Design developments and testwork over the past two years indicate that the time may be right for field trials.

Jan 1, 1990

By R. Mark, R. Richards

The Washington National Cathedral is one of the largest masonry structures in the USA, and like many of its European Gothic counterparts, it required nearly a century to construct. The design was altered during this period, resulting in greater loadings than were originally anticipated on the soil beneath the foundation. When signs of continuing differential settlement were observed in the early 1990's, the Cathedral approached the US Bureau of Mines (now the National Institute for Occupational Safety and Health (NIOSH)) for assistance in monitoring the movements of the massive towers and walls. An array of dual-axis tiltmeters was installed about 40m above ground level to measure wall and tower inclination, with the data sent over a dedicated phone line to the NIOSH Pittsburgh Research Laboratory for processing. Mechanical gages and string-potentiometers are also being used to measure motion across cracks and joints, and differential pier settlement is being monitored with optical-level surveying. Data have now been collected for almost 7 years, and they show a long-term settlement trend masked by dramatic diurnal and seasonal thermal movements. The paper discusses the major findings of the study, implications for the future of the Cathedral, and conclusions regarding the use of geotechnical monitoring at major national monuments.

By Leigh Freeman

The War for Talent ?McKinsey & Company 1997 and 2000 survey ?2001 book by Michaels, Handfield-Jones and Axelrod, Harvard Business School Press

Jan 1, 2007

By C. Yi, M. Onifade, B. Genc, S. Dineva, T. Zvarivadza, M. Khandelwal

Deep level hardrock mining faces increasing challenges from elevated in situ stresses and associated rockbursts. This study aims to develop a systematic framework for evaluating destress blasting effectiveness, with a focus on deep Swedish hardrock mines. The methodology integrates a critical review and adaptation of global best practices: advanced numerical modelling (static and dynamic simulations), field-based rock fracture monitoring using ground penetrating radar and borehole imaging, and application of rockburst prediction criteria including the strain energy storage coefficient (F), brittle shear ratio, and burst potential index. Geostatistical simulations, machine learning models, and industrial internet of things-based, real-time monitoring are proposed to enhance predictive accuracy, model calibration, and operational adaptability. Key findings show that effective destress blasting evaluation requires multi-modal integration of numerical outputs, field observations, microseismic trends, and uncertainty quantification, accounting for site-specific geological variability and dynamic stress redistribution. The study advances the field by proposing a predictive, feedback-driven evaluation framework tailored for deep Swedish mining conditions, capable of improving proactive rockburst risk management. It offers both practical tools for mining practitioners to optimise stress management, reduce seismic hazards, and enhance excavation safety, and academic foundations for future refinement of destress blasting models, geotechnical monitoring strategies, and adaptive design protocols. This research contributes to safer, more efficient deep mining operations by bridging gaps between theoretical modelling, empirical monitoring, and real-time, data-driven blast design optimisation strategies.

Jun 27, 2025

By G. Kordosky, A. Feather, M. Virnig, P. Crane

Introduction The post World War II nuclear arms race and interest in nuclear power generation resulted in a significant demand for uranium in the 1950’s. This led to the development of uranium solvent extraction technology and uranium became the first metal to be recovered on a large scale by solvent extraction (SX) (1), interestingly more than 100 years after the extraction of uranium from an acid nitrate solution using diethyl ether was first reported by Peligot.(2) For a variety of reasons discussed elsewhere (3,4) there have been upheavals in the supply demand picture and price for uranium since the 1960’s. (Figure 1) The low price of uranium from the mid 1980’s until 2004 resulted in a depression of new resource exploration and mine development along with uranium mine / mill closures and decommissioning. People with skills in uranium processing could not find suitable employment and many experienced engineers and metallurgists took jobs elsewhere or retired. This resulted in a significant brain drain with respect to uranium processing technology.

Jan 1, 2007

Assess the technical feasibility of mining small and/or deeply buried frozen placer deposits from the surface through boreholes.

Jan 1, 1997

Correlation of Air Recovery with Thin Film and Froth Stability in Flotation

Sep 13, 2010

By Robert Hopler

Earthquakes, ground vibrations, seisms, or whatever you want to call the shaking of the earth, have been a fact of life throughout time. In spite of this, most people (except those unfortunate enough to live in seismicallyactive areas) have probably never felt this phenomenon, or if they have, only a very few times in their entire lifetime. However, when it does happen, nothing is more frightening than the sudden shaking of the earth beneath us - after all, we think of the ground we walk on as the unyielding, solid underpinning of our existence.

Jan 1, 2006