Search Documents

By A. Vien

Over the past several years, Svedala has developed a continuous charge monitor (CCM) for tumbling mills. It consists of a strain gauge embedded into a rubber lifter and associated electronics. This paper describes the results of a research program to evaluate the technical and economical merits of such a device on a SAG mill. The evaluation includes validation through discrete element modelling and comparison to measured static volumetric load. Inclusion of the measurement into a control strategy and its potential for condition monitoring is discussed.

Jan 1, 2001

By J. L. Huitt, IM. L. Slusser, E. E. Glenn, M. L. Slusser

This paper is concerned with: (1) an analysis and interpretation of the filtration characteristics of drilling muds on filter paper, and (2) an interpretation of early stage "filtration" on consolidated synthetic porous media, herein referred to as the "surge loss" period. It is shown that water-loss data can be plotted so as to disclose the existence of a surge period, a non-uni-form cake thickness period, and a constant pressure filtration period. The same periods occur during exposure of consolidated porous media to muds. The data on consolidated porous media indicate that: (1) mud particles bridge pores inside porous media during the surge period, and (2) "filter cake" build-up inside porous media occurs during subsequent filtration. The data also show that the surge loss increases with sample permeability and with pressure differential. INTRODUCTION The phenomenon of mud filtrate invasion into porous sands of a drilling well has been recognized for many years.1,2,3,4 Part of API Code 29 is concerned with the filtration testing of a drilling mud to yield data on this subject. In a number of investigations "plastering properties" of muds were studied,5,6,7,8 "plastering" apparently meaning cake forming properties. In such studies the characteristics (thickness, permeability, and toughness) of the cake and the rate at which the liquid phase of the mud was separated from the solids (filtration rate through the cake, commonly referred to as water loss) were measured or at least considered. From the standpoint of its effect on well productivity, filtrate invasion into "clean" water-wet pay sands (i.e., those containing no clay minerals) may not necessarily be a serious problem. An increase in water saturation in the zone immediately around the wellbore would cause loss of oil permeability. However, in such a system, much of this water may be removed by oil production. If filtration occurs into "dirty" sands (i.e., those containing appreciable clay minerals), clay swelling or other mechanisms may cause losses in oil permeability which cannot be overcome by oil production.'.' The phenomenon of mud particle invasion into the pay sand of a drilling well was considered to be a possible serious factor in the early days of rotary drilling. Opinions varied as to whether drilling fluids "mudded up" and "sealed" oil sands. In 1932 Rubel,9 Gill,10 and Parsons," in separate papers, presented differences of opinion together with some laboratory and field data concerning loss of oil production caused by drilling fluid invasion into pay zones. These papers, and the discussions, furnish a large background on this subject and indicate the very clear thinking of many men at a time when petroleum production technology was in its infancy. Jones and Babson,6 and Silent,' experimentally found that the depth to which mud particles invaded water-saturated sand packs was small (no greater than 1/16 in). Arn-quist12 in 1937 observed loss of water permeability due to invasion of mud particles into water-saturated, consolidated, sandstone samples. Williams and Cannon5 studied the filtra-tion properties of drilling muds and mentioned "sludge" which penetrated a short distance into the water-saturated filtering medium (sand pack). Byck5 concluded that formation permeability had no effect on the plas-

Jan 1, 1958

By G. Couture, J. -F. Dubé, F. Letarte-Lavoie

"The Xstrata Nickel Raglan concentrator, located in Quebec’s Nunavik region, has been in operation since 1997. Originally designed to process 800,000 tonnes per year of high-grade nickel ore, the plant’s current capacity is 1.3 million tonnes per year due to various optimization projects. In 2011 and 2012, the Metallurgical group, with assistance from BBA, updated and optimized the variables affecting SAG throughput in order to optimize process stability while maintaining maximum plant throughput. This project consisted of reviewing the control strategy and completely updating the pre-existing Fuzzy Logic controller. This paper describes the successful update of the controller including a complete revision of control rules, a new process control strategy and the integration of new process variables, most notably mill rotational speed. It will also show how this new approach has provided a simple and robust way of delivering both an increase in throughput while reducing process variability.INTRODUCTIONThe Xstrata Nickel Raglan Mine concentrator is located in Northern Quebec along the 62th parallel. It has been in operation since 1997 and was originally designed to treat 800,000 tonnes of ore annually. The Raglan Agreement held with the Makivik Corporation and the Inuit communities limits the annual tonnage of ore that can be processed at 1.32 million tonnes.The ore is processed in a 24 foot variable speed, semi-autogenous grinding mill (SAG). The conversion from Autogenous Grinding (AG) to SAG was completed in 2006. Before the ore is processed by the SAG, its size is analyzed by a Wipfrag camera that provides a granulometry estimate. A cone crusher reduces the SAG’s discharge screen’s oversize material. A 14 foot diameter ball mill ensures final grinding before the flotation stage.Many control strategies were used at the SAG over the past few years. Fuzzy Logic was first used in 2007 in order to control tonnage feed to the SAG. This first version only measured the value of the variables without taking into account their rate of change. Revisions were made over the course of the last few years to improve controller performance. Other variables were added such as slurry density and crusher Closed Side Setting (CSS). The previous revision of the Fuzzy Logic was done in 2009 with a review of the rules only."

Jan 1, 2013

By George Espey, George Sachs, G. B. Kasik

IT has been reported frequently that the hardness and strength vary over the cross section of cold-worked, particularly cold-drawn, material. Brass rod and wire usually have been found to possess a maximum strength and hardness near the surface.1,2 According to Sachs,' the center fiber has about the same strength as a wire stretched by the same amount in a tensile-test machine, the strength increasing toward the surface (Fig. I). These differences are particularly large for wire given a small reduction on drawing through a die with a wide opening. However, with increasing reduction and hardness, a tendency to form a thin soft surface skin becomes apparent. On the contrary, copper wire has usually been found to possess a soft surface skin3-5 and it has been reported by Harris3 that during the cold-drawing of hot-rolled wire the surface layer becomes increasingly softer than the core, while the layer of maximum strength moves toward the core, it being found near the surface at first. The increase of strength and hardness from the core to the skin is readily explained by the observation that, in addition to the stretching, the layers of a rod or wire are sheared more the closer they are to the surface.1,6-8 However, the presence of a soft surface layer can be attributed only to an annealing effect. The source of such a softening might be the extremely high temperature that originates from the friction between

Jan 1, 1942

By G. B. Kasik, George Sachs, George Espey

IT has been reported frequently that the hardness and strength vary over the cross section of cold-worked, particularly cold-drawn, material. Brass rod and wire usually have been found to possess a maximum strength and hardness near the surface.1,2 According to Sachs,' the center fiber has about the same strength as a wire stretched by the same amount in a tensile-test machine, the strength increasing toward the surface (Fig. I). These differences are particularly large for wire given a small reduction on drawing through a die with a wide opening. However, with increasing reduction and hardness, a tendency to form a thin soft surface skin becomes apparent. On the contrary, copper wire has usually been found to possess a soft surface skin3-5 and it has been reported by Harris3 that during the cold-drawing of hot-rolled wire the surface layer becomes increasingly softer than the core, while the layer of maximum strength moves toward the core, it being found near the surface at first. The increase of strength and hardness from the core to the skin is readily explained by the observation that, in addition to the stretching, the layers of a rod or wire are sheared more the closer they are to the surface.1,6-8 However, the presence of a soft surface layer can be attributed only to an annealing effect. The source of such a softening might be the extremely high temperature that originates from the friction between

Jan 1, 1942

By M Olsen, L van den Berg

Bowen Basin coalmines suffer from hot and humid ambient conditions during the summer period. The ambient conditions combined with high VRTs, increasing depth of working and significant equipment heat loads results in heat issues underground. Coalmines operate under heat stress management plans as required by legislation with associated trigger action response plans (TARPs). Some mines also employ refrigeration as part of their heat management strategy.A recent case study was conducted on a mine producing about 4.5 Mt/a from their longwall and experiences summer surface ambient temperatures of about 23.5ºCwb. The expected virgin rock temperature is 46ºC at 300 m depth. The mine currently introduces a modest amount of surface cooling at the portal using ‘off-the-shelf’ air conditioning units. This system does not effectively manage face temperature primarily due to positional inefficiency.Underground conditions remain hot in summer and work is typically undertaken in accordance with the Heat TARP. This has a direct impact on the productivity of crews, worker comfort and also negatively impacts the workforce morale. The mine commissioned a study to determine a refrigeration strategy aimed at maintaining underground conditions below TARP levels 90 per cent of the time.The ventilation network model was calibrated against actual temperature data to simulate the heat loads including longwall, conveyor system, strata and auxiliary diesel fleet. This model was then used to determine the cooling requirements for bulk surface cooling, bulk underground cooling, surface district cooling and underground district cooling strategies.These estimates were used to undertake a total owning cost trade-off for the different strategies. The study concluded that a chilled air shaft has the lowest technical risk but the highest total owning cost due to shaft development needs. Introducing chilled water to an underground cooler via boreholes offered the lowest total owning cost and was therefore recommended.CITATION:van den Berg, L and Olsen, M, 2017. Heat load assessment and mine cooling strategies for a longwall coalmine, in Proceedings Australian Mine Vent Conference 2017, pp 231–236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By D. J. Greeff

By making use of genetic programming, empirical models for metallurgical processes can be evolved that are more cost-effective than models determined by means of classical statistical techniques. These methods explore populations of candidate models assembled from sets of variables, parameters and simple mathematical operators, and do not require explicit specification of model structures. The application of the proposed strategies is illustrated by means of a case study pertaining to the leaching of nickeliferous chromite ores. Modelling of the nickel and cobalt extraction from the ores yielded models of similar accuracy compared to those obtained by non-linear regression and artificial neural networks. However, in the case of the iron extraction from the ores, the genetic programming model was significantly more accurate than both the regression and neutral network models.

Jan 1, 1998

By Thomas Sisley, Jozef Zurawski, Richard Switalski

Hilltop Interceptor Contract G is one of the segments of the wastewater control system in the greater Cleveland area. The tunnel is a relief interceptor constructed by the Northeast Ohio Regional Sewer District to minimize combined sewer overflows in the Easterly Service Area. The design study identified the need for a 3.35 m (132 in) diameter, 3.35 km (11,000 ft)in-line storage conveyance tunnel to be constructed at depths of 30 to 70 m (100 to 230 ft).Six structures for access, future flow drop, work shafts and overflow control were required to complete the system. The interceptor reduced the design peak flow from 12.5 m3/s(285 mgd) to 6.1 m3/s (140 mgd) by detaining in line 22,800 m3 (six million gallons) of wastewater.

Jan 1, 1997

Coal has been mined in the central Appalachian coalfields of southern West Virginia, western Virginia, and eastern Kentucky for more than a century. The dwindling reserve base consists in large part of coal that would have been considered unmineable by earlier generations. Nearly every current operation is working on a property where coal has been extracted in the past, from seams either above, below, or both. NIOSH is conducting research aimed at helping mine planners prevent hazardous conditions due to multiple seam interactions. To-date, more than 300 case histories have been collected from underground mines, mainly from central Appalachia. This paper focuses on several of the more challenging situations that have been encountered, including: • Room-and-pillar development 20 ft (6 m) beneath full extraction workings at a depth of 1,000 ft (300m) of cover (Virginia) • Pillar recovery 45 ft above full extraction workings at 900 ft (270 m) of cover (Virginia) • Near-simultaneous room-and-pillar mining with pillar recovery with 40 ft (12 m) of interburden and 1,500-2,000 ft (450-600 m) of cover (Kentucky) • Longwall mining directly beneath main entries in overlying seams (West Virginia) • Some of these operations have been highly successful in overcoming the challenges, others less so. The lessons learned from their experience will help ensure that these and similar difficult reserves can be mined safely.

Jan 1, 2006

By Jeffrey D. Thatcher, Debra W. Struhsacker

With the burgeoning development of precious metals heap leach mining projects throughout the country regulatory agencies are beginning to take a closer look at the short-and long-term environmental consequences of heap leach mining. This increase in regulatory review is occurring on federal, state and local levels, and is affecting both large- and small-scale mining developments. Small-scale mining developments are receiving especially critical regulatory scrutiny because in the eyes of some regulatory agencies, small developers lack the credibility automatically accorded to major mining companies. This is due in part to a bad image of small miners based upon past environmental problems and permit violations caused by a few, small operators. The proponent of a small mining development thus faces special problems during the project permitting process, and must convince the regulatory authorities of his company's ability and commitment to plan, develop, and decommission a mining operation in compliance with environmental regulations. Not only must the small developer have a thorough understanding of the regulatory requirements affecting his project, he must also devote considerable effort to careful internal planning in order to produce a well organized approach to project permitting. The importance of proper planning cannot be overstated. Project planning is key to convincing the regulatory agencies that the small miner is capable of developing a viable project. More- over, the economics of a small mining project demand permit acquisition at modest cost and in a timely fashion. A well planned permitting effort will thus ensure that permits are received within budget and on schedule. This paper will review the federal, state, and local permitting requirements for heap leach projects, and the variability of these requirements from state to state. The environmental assessment process for projects developed on public lands, and the acquisition of zero- discharge water quality permits, air quality permits, and local special use permits as they apply to small mining developments will be discussed. The paper will conclude with a review of project decommissioning and cyanide neutralization requirements and their implications for small-scale heap leach projects.

Jan 1, 1987

By Shahriar Vandani, Andy Herlache, Andrew Bro, Wei-Yu Chen

"The Presidio Parkway Project will reconstruct approximately 1.6 miles (2.6 km) of highway, including seven new bridges, three new cut-and-cover tunnels, and a new undercrossing connecting the Golden Gate Bridge to the City of San Francisco, California. The project site is approximately 5.6 miles (9 km) from the San Andreas Fault, capable of producing magnitude 8 earthquakes. Seismic hazards include strong ground shaking, soil liquefaction, ground settlement, and lateral spreading. The Main Post Tunnels (MPT) are two parallel cut-and-cover concrete tunnels approximately 1100 feet (335 m) long. The MPT site underlain by loose sandy soils susceptible to liquefaction and lateral spreading. Excessive racking and permanent displacement due to lateral spreading are identified as the main seismic vulnerabilities. Analyses showed that without ground improvement, tunnel racking of over 5 inches (13 cm) and permanent lateral tunnel displacement of up to 15 feet (4.6 m) could be anticipated. Cement Deep Soil Mixing (CDSM) is proposed to mitigate slope displacements and increase lateral stiffness of the foundation materials to reduce tunnel racking. A series of 2-D fully dynamic time domain analyses were performed to evaluate the performance of CDSM, confirm that performance criteria are met, and optimize the CDSM geometry and replacement ratio. The use of CDSM reduced the permanent tunnel displacement from over 15 feet (4.6 m) to less than 1 inch (2.5 cm). Tunnel racking was also reduced significantly. The adopted analytical approach presented herein can be considered for future tunnel design projects in seismically active areas.Introduction The Main Post Tunnels (MPT) are an integral component of the Presidio Parkway project which will replace the existing facility with a new multi-lane roadway between the Golden Gate Bridge and the City of San Francisco. The MPT are two parallel cut-and-cover concrete tunnels approximately 1100 feet (335 m) in length. As shown on Figure 1, the project site is located in a seismically active area, about 5.6 miles (9 km) east of the San Andreas Fault and 12.5 miles (20 km) west of the Hayward Fault. The San Andreas Fault can generate magnitude 8 earthquakes while the Hayward Fault is capable of producing magnitude 7.3 earthquakes. The design Peak Bedrock Acceleration (PBA) is 0.46g for the upper level design earthquake. The project alignment is shown on Figure 2."

Jan 1, 2014

By I. Yildirim

Water contact angles of talc powders were determined from the values of the heats of immersion measured using a flow microcalorimeter. The results were used to calculate the contact angles using a rigorous thermodynamic relation. In the present work, the calculation was carried out using the temperature coefficient of the contact angles determined experimentally using another method. The results obtained in the present work on several different talc samples are compared with those obtained using other methods.

Jan 1, 2001

By Geovane Viturino da Silva, Diogo Costa, Paulo Eduardo Marcelino, Alan José Santos De Almeida, Marco Antônio dos Reis, Deilton de Oliveira

A utilização de coque como combustível em Altos Fornos é necessária, apesar das restrições ambientais e dos custos envolvidos. Para diminuir a quantidade de coque utilizado no processo, são adotadas medidas como a injeção de hidrocarbonetos, dentre os quais, o carvão pulverizado, que é comprovadamente um bom substituinte parcial do coque carregado nos Altos Fornos. A injeção de carvão pulverizado (pulverized coal injection - PCI) propicia um maior retorno econômico, quando utilizado no processo de fabricação do ferro-gusa, pois permite uma maior capacidade da taxa de injeção ao se comparar com o emprego de óleos, gases e outros substituintes. No processo da injeção de carvão, conforme o objetivo do presente trabalho, se faz necessária uma baixa variabilidade (relação da taxa de carvão real com o set point pedido). A utilização da metodologia (Six Sigma) foi de fundamental importância para as principais ações adotadas, e trouxeram como principais resultados, estabilidade nos processos de moagem e injeção, bem como a redução do desvio da taxa de injeção de 16% para 10%, gerando uma economia para a Ternium BR.

Oct 1, 2019

By J. Pinkley

DSI DYWI Rock Dust application is aiding in enhancing safety and productivity in underground coal mining. DSI DYWI Rock Dust combines wet dusting technology and polymers to allow for drying and lift characteristics for rock dusting. DSI DYWI Rock Dust typically dries within 24 to 48 hours depending upon the mine air velocity and humidity. The DSI DYWI Rock Dust Applicator Machine is a completely hydraulic unit. The DSI DYWI Rock Dust Applicator machine allows for batching of product and face spraying operations in permissible locations. The DSI DYWI Rock Dusting Applicator Machine fits in one half of a battery or diesel scoop bucket for ease of transport. It is completely hydraulically powered by the PTO circuit. The DSI DYWI Rock Dust Applicator unit requires a scoop operator, and a person to operate the spray wand, simple operation with two personnel. The first demonstration was at an underground continuous miner room and pillar coal mine which produced a pilot test period opportunity, which proved to be successful, and has now been in full launch mode with the US underground coal mining industry. A typical batch of operation allows for 250? of roof and rib (19? wide by 6? in height) coverage of DSI DYWI Rock Dust application. The DSI DYWI Rock Dust Applicator contains a hydraulic powered air compressor which allows for 30-50% more coverage per batch by improved dispersion of product via air assist spray nozzle. DSI DYWI Rock Dust will add approximately $0.02 to $0.04 per clean ton of coal cost to the mining operation over traditional rock dust cost depending upon mining height.

Jan 1, 2012

By U. Schwarz-Schampera, P. Stoffers

The main characteristics of the 2545 km Tonga-Kermadec subduction system are the subduction of the Pacific Plate and its sedimentary cover in the Tonga-Kermadec trench and the extension and rifting of the lithosphere behind the active island arc in the Lau basin - Havre Trough back-arc systems. The subduction of the Louisville Seamount chain at 25.6°S affects the tectonic and volcanic system and separates the island arc into the Tonga arc and the Kermadec arc, respectively. To the west, a Miocene island arc is represented by the Lau-Colville ridge. The crustal extension between the Lau-Colville and the Tonga-Kermadec ridge started at about 6 Ma, and induced their separation and the onset of the southward rifting since about 5 Ma. Characteristics of the Tonga-Kermadec arc system include (i) the fourthfold decrease of the subduction rate from 24 cm/a in northern Tonga to 6 cm/a in the southern Kermadec trench, mainly north of 23.5°S; (ii) the development from fast spreading in the Lau basin (16 cm/a) to slow rifting (2 cm/a) in the southern Havre Trough with the transition from spreading to rifting at 23.5°S; (iii) variations in the composition and the volume of the subducting sediments and rocks (detritus from the Samoan hotspot at the northern Tonga arc; the aseismic Louisville ridge at the southern Tonga arc; increasing terrigenous sediments from New Zealand at the southern Kermadec arc); (iv) a number of active volcanic centers younger than 1 Ma and characterized by significant shallow submarine hydrothermal systems.

Aug 24, 2006

By T Haskell, Y Joe, S Dickie

A current trend amongst producers is the increase in dewatering of iron ore fines (<0.5 mm), due to an increase in wet beneficiation processes used to upgrade lower quality ore deposits, increased water content in orebodies located below the water table, and increasing focus on transportable moisture limits (TML). Vacuum filtration is commonly used for dewatering of iron ore fines, and as with all filtration processes performance decreases with particle size. Significant improvements are possible with the use of filter aids, usually anionic surfactants and flocculants. Anionic surfactants reduce the surface tension of the associated water, which is then removed more readily leading to improved filtercake moistures. Anionic flocculants used correctly can improve cake permeability, in turn, decreasing cake formation times and increasing filtration rates. In addition to increased throughput, savings and benefits for producers can include: moisture limit penalties, improved handleability, along with energy and water savings.The effect of filter aids on two iron ore fines samples from the Pilbara region were evaluated using a lab scale vacuum filtration unit. The first sample showed a reduction in the filtercake moisture content by 2.3 per cent weight/weight (w/w) with the use of BASF’s Drimax® 1234. For the second sample a reduction in the filtercake moisture of 3.4 per cent w/w along with an increase in filtration rate of 20 per cent was achieved by using a combination of Magnafloc® 5250 and Drimax® 1239 NF, as both filter throughput and cake moisture were considered important by site.CITATION:Haskell, T, Dickie, S and Joe, Y, 2017. The use of filter aids on iron ore fines, in Proceedings Iron Ore 2017, pp 183–186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The occlusion of unliberated gold particles in silicates and sulfides in crushed/milled ore dictates the recovery that can be expected. The grade of this occluded gold in cyanide leach residues shows a consistent, general relationship to the head grade of the ore, irrespective of mineralogy or geographical location. The residue grade almost invariably increases with the head grade, but not in proportion to it. This phenomenon appears to stem from the nature of the geological events originally responsible for creating the ore deposits. A statistically-based technique for determining the true head grade-tail grade relationship from gold plant operating data is described. The effect is illustrated with results from several worldwide gold milling operations analyzed over the last 35 years.

Jan 1, 2008

According to the classification of water conservation mining in shallow coal seams in China, when the ratio of the impermeable layer thickness to the mining height is less than 18, the mining belongs to the category of special water conservation, and the strip backfilling mining method is employed. This study is based on the geological conditions in northern Shaanxi. By analyzing the stability of the impermeable layer, the stability criterion of the impermeable layer was developed. The study also investigated the compositions and properties of the backfilling materials. The results show that reasonable subsidence of the impermeable layer is allowed during mining under the basic precondition (upward cracks and downward cracks are not connected).

Jan 7, 2020

By Panfeng Gou

In order to solve the problems of supporting the roof of the gateroads affected by a fault, the movement characteristics of roof strata must be fully understood. In this paper, a plane stress physical simulation model was constructed to study roof strata displacement and deformation of gateroads driven in the hanging wall of the fault after the coals in the footwall were extracted. The results indicated that, due to the effect of fault, vertical cracks, orienting parallel to the dip of the fault, occurred in the horizontal direction of the model within the areas affected by the fault. The roof strata are discontinuous. On the other hand, non-uniform subsidence of roof strata occurred due to the bedding plane separation in the vertical direction. Roof strata, especially the lower roof strata, dip toward the fault. Failure of the surrounding strata is not symmetrical with the roof and floor close to the fault being deformed severely. In the selection of type of supports for the gateroads, the U-shaped steel supports are superior to roof bolting.

Jan 1, 2006

By A. C. Moorgas, J. Divall

This study investigates the feasibility of using waste iron slag, the by-product from a mineral sands processing works, in road construction. The study includes the different options investigated for the treatment of a leachate that is produced during the cooling of the iron slag, prior to processing. It also reviews the reasons for choosing the current treatment option that is being trialed. Cooling the iron slag with water results in the formation of a leachate with a high pH and high sulphide concentration. This leachate can seep into the ground and, over time, it will contaminate the ground water. A system was designed to collect and treat the leachate to prevent contamination of surrounding natural water sources. Numerous leachate treatment options were investigated to find cost effective method of treatment After cooling, the iron slag is passed through an iron recovery plant and the unsaleable product is placed on a dumpsite. Rain percolates through the dumpsite, which can result in the formation of a leachate that can contribute to a contaminated plume. After extensive testwork, it was found that the dumpsite, which was leached of contaminants, could be screened and used as a G5material (specifications in Table II) in road construction. The initial challenge was to establish that this material was environmentally safe for use in this particular application. Approval from the Department of Water Affairs (DWAF) was required for the testwork and then for the long-term use of this material in the construction industry. The following challenge involved establishing a market for the material. Construction companies in the area were reluctant to change to a new product that was not naturally occurring. The economics of this project are extremely sensitive to transport costs and hence only projects within a specified radius can be supplied with the Black Top Gravel (BTG). This project is not are venue generator, but it does save the money that would be required to manage the dump, and it reduces the closure costs.

Jan 1, 2003