Search Documents

By Shengli Wu, Wei Huang, Xinliang Liu, Kaifa Zhang

The slagging behavior, the phase of primary blast furnace slag and its transformation law of structure for the single furnace burden were studied in this paper. The results showed that the formation of primary slag was controlled by CaO/SiO2, Al2O3 content, MgO content, reducibility, iron content and porosity of the furnace burden. Fayalite (2FeO•SiO2) was easily formed from acid ferrous furnace burden while kirschsteinite (2(Fe,Ca)O•SiO2) was produced from alkaline ferrous furnace burden

Jan 1, 2015

By Shu Xinqian, Zhou Weining, Shan Zhiqiang, Feng Jifu

"Modified calcination conditions on the extraction of rubidium resources from muscovite (KAlz[AlSi301o](OH)2) ore are systematically studied. The impact of various factors on the rubidium leaching rate is also analyzed, including the agent types, roasting time, the mass ratio, roasting temperature, etc. The results indicate that the best agent is a combination of sodium chloride and calcium chloride, its mass ratio ofmuscovite/NaCl/CaClz is 1:0.25:0.25. Calcined at 8500 for 30 minutes, the rubidium leaching rate is up to 90%. The reaction of muscovite ore with the chlorinating agent CaC12 has been studied by TG/DSC, the calcined intermediates are identified by XRD, and the surface morphology before and after leaching is characterized by SEM. Rubidium chloride products can be obtained with a purity of 92% by using t-BAMBP extraction, hydrochloric acid reextraction and purification.IntroductionRubidium is one ofrare alkali metals, which is found in 1981 by German R.W. Bunsen and G.R. Kirchhof. Rubidium includes the following features: atomic number is 37, each atom weight 85, the body-centred cubic lattice, each unit cell has two metal atoms, and the density is 1.532g/cm3. The properties of low melting point (312.46 K) and malleability make rubidium have a strong chemical activity and photoemission. Rubidium provides a main material for manufacturing phototube with a wide range oflight waves, which possess high sensitivity and stability. Efforts are being made to carry out research on rubidium ion gngine, magnetic flux generators and thermoelectric transudcer, etc. Rubidium exists in muscovite ore(KA12[AlSh01o](OH)2 (monoclinic system and hexagonal layered structure) as isomorphism and replace the large radius of the potassium atoms, as well as part of rubidium locate between structure layers. The complex components bring great difficulty in comprehensive recycling."

Jan 1, 2013

By Zhucheng Huang, Yuanbo Zhang, Kecheng Zhang, Guanghui Li, Tao Jiang

"With rapid development of Iron and Steel industry, plenty of metallurgical dusts and sludges are generated, which have not been effectively utilized because of their poor hydrophilicity and bad ballability. Agglomeration and roasting of metallurgical dusts & sludges with a new-type composite binder are studied in this paper. The results indicate that the dosage of the new binders can be decreased to 2.5 wt% from 3.5 wt% when using the wet-grinding process. Under the optimal conditions of briquetting pressure 2070 N/cm2, briquetting moisture content 13 wt%, roasting temperature 1000 °C and roasting time 40 min, the qualities of the green, dry and roasted briquettes meet the requirements of the industry production. The finished products have the compression strength of more than 2000 N/cm2, which can be used as high-quality burdens for blast furnaces.IntroductionWith rapid development of Chinese Iron & Steel industry, there are more and more serious resource shortage and environmental pollution existing. Converter sludges, containing 30% ~ 40 wt% moistures, are typically difficult for recycling [1]. Foreign processing technologies for sludges treatment are relatively advanced including cold-bonded agglomerates for blast furnace, RHF reduction for the dusts and sludges with high content of Zn and Pb, smelting and reduction. Domestic iron and steel companies use a small amount of sludges in sintering. However, the sludges have the characteristics of high moisture and containing harmful impurities, which directly affect the sintering mixture permeability and product quality [2-5]. There are also other technologies such as production of metallized pellets, cooling agents for steelmaking, etc [6]. All of these deficiencies and applied are not in large-scale."

Jan 1, 2011

By Hande Cavus, Ibrahim Yusufoglu, Cem Kahruman

"In this study, ammonium tetramolybdate (ATM) was obtained as the intermediate product of ammonium heptamolybdate tetrahydrate (AHM). The thermal decomposition mechanism of ATM was investigated under nonisothermal and isothermal conditions in air and inert gas atmospheres. Nonisothermal experiments were carried out by TGA/DTA/MS while TG was used for isothermal conditions. Characterization of the decomposition products were carried out by XRD and FT-IR. The thermal decomposition of ATM in air proceeds in a single step and forms M0O3 while [(ÍÇ4)2è]ïïï83Ìïè3 and molybdenum suboxide (Ìïè3.÷, ÷=0.025) were obtained in the first and the second steps of thermal decomposition in He, respectively. Activation energies, frequency factors and kinetic model equations were determined for thermal decomposition reactions. Fractional conversion-time diagrams were compared with diagrams drawn according to kinetic model equation.IntroductionM0O3 is usually used as catalyst in industry [1]. AHM is the basic source to produce molybdenum containing catalysts used in petrochemistry [2]. The oxides of Li, V, W, Te, Bi and Sn are doped in M0O3 to produce catalysts, which find commercial applications in the industry. The properties of M0O3 are affected by dissolution, settling, calcination, drying and thermal decomposition processes [1]. There are several studies in the literature about the thermal decomposition of AHM and the characterization of the decomposition products in different gas atmospheres and at various heating rates [3-19]."

Jan 1, 2012

By L. Escudero-Castejon, S. Sanchez-Segado, A. Jha, Y. Hara, S. Parirenyatwa

Oxidative alkali roasting of chromite is the state-of-the-art process for manufacturing chromium-containing chemicals, which involves dealing with serious environmental problems arising from handling Cr6+-containing wastes generated in this process. In this article a new method for the extraction of Cr2O3 from chromite ores is explained, based on the carbothermic reduction of concentrates in the presence of alkali investigated in the temperature range of 950–1050 °C. Under these conditions, the iron oxides present in the ore body are reduced to metallic iron and the resulting separation of chromium occurs by forming sodium chromite (NaCrO2). The reduced samples are magnetically separated for the recovery of an iron-rich fraction, and a non-magnetic fraction containing NaCrO2, MgO and other impurities. The further treatment of the non-magnetic fraction by leaching yields a Cr2O3-rich product of approximately 85% purity, with remaining alumina, alkali and magnesia. The main advantage of the process is that, under reducing atmosphere and subsequent leaching conditions, the oxidation of Cr3+ to Cr6+ is completely avoided; thereby decreasing the risk of land, air and water pollution.

Mar 1, 2017

By Ana E. Bohé, Fabiola J. Alvarez

"The separation of nickel from the aluminum present in spent catalysts and different metallic industrial residues, is proposed in the following systems: alloy Al2Ni and the mixtures 50 wt% Ni + 50 wt% Al, 10 wt% Ni + 90 wt% Al2O3 and 12 wt% NiO + 88 wt% Al2O3. The experiments were carried out in a tubular reactor with a flow of 2 l/h of gaseous chlorine and from 200 ° to 800 °C. The final products of the reaction, extracted from the hottest zones of the reactor where characterized by XRD, SEM, EDS, AA and XRF, as NiCl2 y NiCl2.6H2O while in the coldest regions AlCl3 was deposited in the first two cases and in the other there was a residue of ?, a- Al2O3, sometimes mixed with some remainder of Ni and NiO. The procedure attained different separation factors which showed the optimun conditions for the recovery of both metals. Introduction Some studies of nickel corrosion were carried out in chlorine gas at temperatures above 950ºC, and suggested that nickel is not corroded below 538ºC. [1] However, in a previous work it was shown that the chlorination allows the separation of nickel from aluminum and the formation of NiCl2 was detected from 200ºC in binary mixtures Ni-Al 50 wt%, for isothermal conditions in chlorine flux. [2] Other researchers obtained selective chlorination above 650ºC of a fly ash containing 1.4 wt% of Ni and other metals (V, Mg, Al and Fe). The Ni was separated from the Mg and NiCl2 started to vaporize at 550ºC and was after condensed in a zone of the reactor above 380ºC with 90% of purity. [3]"

Jan 1, 2008

By Shengli Wu, Yuandong Pei, Zhixing Zhao, Shuhai Ou, Jiangshan Shi, Huaiying Ma, Jun Xiong

Spraying technology on sintering surface bed after ignition has become a hot research topic, with the purpose of achieving energy-saving, emission reduction and improvement of sintering indexes. In this paper spraying steam technology was researched from theory, experiment and practice. First of all, from the thermody- namic and kinetic analysis, the mechanism of sintering surface spraying steam was analyzed and its advantageous effect was con firmed. Based on this, sintering pot test and commercial trial were carried out respectively. The results shown that spraying steam is bene ficial for increasing coke combustion ef ficiency with improving CO 2/(CO+CO2) in the exhaust gas from 80% to about 85% level, through decreasing CO content of flue gas by more than 1000 –2000 ppm. There was a suitable spraying amount to improve the quality of the sinter, and the spraying position of the steam cannot be excessively front and rear. Due to the low steam pressure (1 kg) and temperature (about 100 °C) compared with industrial steam (3 kg and 130 °C, respectively), the sinter quality such as yield index was affected by spraying steam in sintering pot test to a certain extent, and proper spraying amount (0.008 m 3, 50 kg sinter) in sinter pot test is far smaller than application amount in commercial trial (2t/h). It is thought that suitable spraying steam parameters has a comprehensive effect of energy saving and quality improvement.

Mar 1, 2018

By Masanori Harata

A fundamental study was conducted on a new process for producing scandium (Sc) metal or aluminum-scandium (Al-Sc) alloy by the calciothermic reduction of scandium oxide (Sc2O3). In this study, aluminum (Al) and calcium chloride (CaCl2) were used as the collector metal and flux for the reduction, respectively. A mixture of Sc2O3, Al, and CaCl2 in a tantalum crucible was placed inside a stainless steel reaction container, and the feed mixture was reacted with calcium (Ca) vapor at 1273 K for 6 h. After the reduction experiment, the reaction product (CaO), CaCl2 flux, and excess Ca reductant were removed from the obtained alloy sample by leaching with an aqueous solution. The formation of Al3Sc in the Al matrix phase of the alloy was confirmed by X-ray diffraction (XRD) and electron microprobe analysis (EPMA). This result indicates that Sc2O3 was successfully reduced to metallic Sc and alloyed in situ to form liquid Al-Sc alloy during the reduction. When Al was not used in the reduction experiment, a complex oxide (CaSc2O4) was formed, and the reduction was incomplete. This study demonstrates that the Al-Sc alloy can be directly produced by calciothermic reduction using CaCl2 flux and Al collector metal.

Jan 1, 2006

By Haydar Güneş

In this study, a hydrometallurgical process was evaluated for the recovery of Nd from a Nd-Fe-B magnet. Each leaching test was performed at the solid (weight) to liquid (volume) ratio of 1:50 and was mixed at 400 rpm at ambient temperature. The effects of 3 different acids (HCl, HNO3, and H2SO4) on the extraction of Nd were investigated and H2SO4 was found to be more effective than other acid solutions. Under the optimal conditions, pregnant leach solution was produced with H2SO4 for subsequent Nd precipitation testing. Each precipitation test was carried out using 100 mL of feed solution mixed at 600 rpm at 25°C. NaOH and H2C2O4 were used for Nd precipitation. The highest Nd was precipitated as Nd2(C2O4)3, 10H2O with C2H2O4 at 20 min.

By Ronald K. Riddle

The processing of lateritic ores in rotary drying and preheating/pre-reduction systems has historically been plagued by problems associated with significant dust generation. These problems include handling issues, kiln capacity limitations, negative impacts on furnace stability, a reduction in nickel recovery and higher operating costs. The dust is formed in the rotary devices during heating and tumbling due to the following three mechanisms: (I) mechanical dccrepitation of the ore as a result of tumbling and attrition, (2) thermal decrepitation during rapid vaporization of internal free and bound water, and the (3) loss of free moisture which functions as a binder. This paper investigates the causes of dust formation, provides methods to reduce dust carryover from the rotary devices, and finally offers methods to recover the dust in the existing pyrometallurgical process. Keywords: Laterite, Drying, Rotary, Dust

Jan 1, 2004

A study was undertaken to remove the Se from waste solutions using a raw form of the biomass called Iota Chips derived from the seaweed, Eucheuma spinosum. Removal of Se from solutions was investigated as a function of time, pH, conc. of Se in solution (0.1 to 100 ppm) and lota Chips to liquid ratios of 10-2 to 10-5. For solutions containing initial conc. of 0.1 ppm Se, with the addition of Iota Chips at a solid to liquid ratio of 10-3, the Se conc. decreased to 0.03 ppm in about 3 hours. Iota Chips absorption capacity to the Se and its application to the treatment of the metallurgical processing effluents are discussed.

Jan 1, 1992

By Yang Cui

The partition ratios of lead and antimony between liquid copper and MgO saturated Cu2O-CaO-SiO2 flux and their removal rate by using CuCl-based flux were measured between 1423 K and 1573 K. For Cu2O-CaO-MgOsatd. system, the partition ratio of Pb was not affected by the CaO content at 1573 K, while that of Sb increased with increasing CaO content. The maximum value was 160 at the CaO content of 15.4 mass%. For Cu2O-CaO-SiO2-MgOsatd. system, two liquid phases of calcium silicate rich phase and Cu2O rich phase were observed at 1573 K. The partition ratios of Pb and Sb between calcium silicate phase and liquid copper depended on the (mass%CaO)/(mass%SiO2) ratio. When the (mass%CaO)/(mass%SiO2) ratio increased, the partition ratio of Pb decreased and that of Sb increased. For CuCl flux, the removal of Pb from liquid copper at 1473 K was possible, and a relatively low concentration could be reached. Moreover, most of lead as metal chloride vaporized from flux. For the removal of antimony from liquid copper at 1423 K, it was difficult by CuCl flux, and the removal ratio was approximately 20% for 75 minutes. However, the addition of CaO or Na2CO3 to CuCl flux was relatively effective to remove antimony, and the concentration of antimony reached a relatively low value after 15 minutes by using CuCl-CaO or CuCl-Na2CO3fluxes. Moreover, a small part of antimony as chloride vaporized from flux.

Jan 1, 2006

By Hyun Kyu Shin, Byeong Deok Lee, Young Eun Lee

The reduction of Mn oxides at pre-smelting steps is an integral part of smelting processes for Mn alloys, and an understanding of its reaction mechanism is expected to contribute to the improvement of processing efficiency for Mn alloys smelting. The phase diagram shows that five Mn carbides are operative in the Mn-C system. Although they are expected to participate in the reduction of Mn oxides, no specific information is available yet to clarify their roles in presmelting carbothermic reaction of Mn oxides. Experiments with composite pellets prepared with Mn oxides and graphite powders show that Mn3O4 is reduced initially to MnO at about 1130oC and, subsequently, to Mn7C3 carbide as temperature increases further. At 1331oC, Mn7C3 carbide dissociates to Mn alloy and carbon. The degree of reducing reaction increases with increasing carbon balance in composite pellets and increasing temperatures.

Jan 1, 2014

By Yuan-bo Zhang, Gui-hong Han, Yan-fang Huang, Tao Jiang, Guang-hui Li

"Under isothermal conditions, the reduction behavior of oxidized pellets balled with bentonite was investigated with CO-CO2gas mixers in the temperature range from 900°C to 1100°C. The whole reduction of oxidized pellets was followed up by means of weight-loss technique. And the swelling index of pellets was examined by visualizing physical changes of pellet in a horizontal tube furnace. The results present that the reduction rate of oxidized pellets is increased with the increase of reduction temperature. While the swelling index is firstly increased and then decreased with the increase of reduction time and reduction extent, which can be ascribed to the disruptive stresses induced during the transformation of hematite to magnetite. The maximum swelling index is gradually increased with the increase of reduction temperature and CO content.IntroductionWith the rapidly development of iron and steel industry, direct reduction iron has been considered as one kind of high quality burdens in electric furnace steelmaking [1]. At present, ""Two-step"" coal-based direct reduction process, which employs oxidized pellets as raw materials, has been used in industrial production [2]. The reduction behavior of iron ore oxidized pellets has been becoming one of the most frequently studied topics in extractive metallurgy[3]. The heat and mass transfer in direct reduction processes results in a series of stepwise reduction reaction (hematite--magnetite--wustite--iron), accompany with the volumetric swelling of pellets[4]. A lot of literatures have been reported on the reduction model of ferrous oxides and swelling behavior of pellets. A. A. El-Geassy K, et.al [5-7] revealed that the reduction process was controlled by chemical reaction at early stage by employing pure Fe203 as raw materials and CO as reduction gas. Chen Y [8] made research on the reduction kinetics of porous oxidized pellets and obtained the rate constant and activation energy of at different reduction stage. In addition, the swelling and disintegration of iron ore pellets was affected by chemical composition of pellet and reducing parameters, which have been studied by numerous investigators [3,9, 1O]."

Jan 1, 2013

By A. Kontopoulos

The Olympias Mine in Northern Greece is producing an extremely refractory gold-bearing arsenical pyrite concentrate, containing on the average 41 3 S, 40 3 Fe, 10-12 3 As, 25 ppm Au and 35 ppm Ag. During the process selection stage, more than a dozen alternative technologies? were considered and an in-depth analysis was prepared for the three most promising, ie roasting, pressure oxidation and biological oxidation. Detailed capital and operating cost estimates were prepared, based, where appropriate, on laboratory and pilot-plant tests. A number of criteria was used for process evaluation and selection, including capital and operating costs; environmental impact, gold' recovery, stage of development, etc. Based on the above evaluation, the Sherritt Pressure Oxidation Process was finally selected. A detailed description of the process selection stage, supported with laboratory and pilot-plant test results on many of the processes considered, will be? presented.

Jan 1, 1989

By E. Morrice

Solubility of yttrium oxide (Y203) in fluoride melts was experimentally measured in the temperature range of 998 to 1273 K and, YF3 composition in LiF.YF3 melts varying from 20 to 50 mole pct using a graphite crucible in an argon atmosphere. Solubility of oxide in the melt was found to increase with increasing temperature and YF3 composition in the melt. An expression for in XY2O3 as a function of temperature for several melts was deduced. The calculated activity coefficients of Y2O3 in the melts exhibited a negative deviation from Raoult's law.

Jan 1, 1989

By Hideharu Fukunaga, Jin Pan

"The recognition of Metal Matrix Composites (MMCs) as a means of providing high specific strength, high specific stiffness, excellent wear resistance, low thermal expansion and improved high temperature properties has led to a number of new processing, not previously used for plastic and ceramic matrix composites. As a primary fabricating process, the liquid methods are the major ones, which are reviewed briefly from the view of processing terminology. One of them, squeeze casting process is the most traditional and well-developed, because it is rapid, versatile and near-net shape production of materials. Two of new squeeze casting processes are presented to offer the hardness· controlled MMC and the· functionally graded MMCs as well as a newly developed whisker preform.I .IntroductionA large number of liquid processes and techniques including semi-solid liquid process are proposed. The most primitive process is ''pressure infiltration casting” of liquid metal into the fiber preform. It is called as follows depending on pressure and its source squeeze casting (1-4) by hydraulic ram, gas pressure infiltration casting (5, 6), vacuum infiltration, centrifugal casting (7), Lorentz-force-driven infiltration (8). The pressurizing on the liquid metal requests a large and stiff equipment, so pressureless infiltration technique has been developed using K2ZrF6 flux (9,10) while the mechanical properties are not high enough, and using H2 gas with Mg alloying element called pressureless infiltration casting (11-13), spontaneous infiltration process (14) and PRIMEX (15). In those processes, no severe reaction occurred between the reinforcement and matrix molten metal. In early l 990's, the reactive processing with pressure or without pressure, in which one material is totally transformed into another of the required shape, eq. assisted oxidation, has been developed, called reaction squeeze casting (16,17), DIMOX (18) reactive infiltration casting (19,20), and in-situ process (21,22). Die casting of SiCp/Al alloy (23,24) and thixocasting of SiCp/Mg alloy (25) are also applied to produce the machine component of MMCs."

Jan 1, 2000

By Anja Pfennig, Axel Kranzmann, Sabrina Schulze

The CCS technique involves the compression of emission gasses in deep geological layers. To guarantee the safety of the site, C02-corrosion of the injection pipe steels has to be given special attention when engineering CCS-sites. To get to know the corrosion behaviour samples of the heat treated steel 1.7225 42CrMo4, used for casing, and the stainless injectionpipe steel 1.4034 X46Cr13 were kept at T=60 °C and ambient pressure as well as p=lOO bar for 700 h - 8000 h in a C02-saturated synthetic aquifer environment similar to possible geological on-shore CCS-sites in the northern German Basin. The isothermal corrosion behaviour obtained by mass gain of the steels in the gas phase, the liquid phase and the intermediate phase gives surface corrosion rates around 0.1 to 0.8 mm/year at ambient pressure and much lower about 0.02 to 0.2 mm/year at 100 bar where the C02 is in its supercritical state. Severe pit corrosion with pit heights around 4.5 mm are only located on the 42CrMo4 steel. Main phase of the continuous complicated multi-layered carbonate/oxide structure is siderite F eC03 in both types of steel.

Jan 1, 2013

By Jin-yan TIE, Ke-xin JIAO, Qian Li, Hai-bin ZUO, Jian-Liang Zhang, Meng SHEN

This paper designs three factors such as temperature, pH, conductivity and three levels of orthogonal test. Temperature is a significant factor. However PH and conductivity are not significant through poor analysis. Further research is conducted on the temperature. Temperature stability is 50 . Suitable water velocity is 2.3m/s, which is calculated based on the largest part of the heat flux intensity and the corresponding water temperature should be controlled with 1.5. Meanwhile, water velocity increased has little effect on the heat transfer capabilities.

Jan 1, 2015

By Himaki Nakano, Kenji Hara, Toshiaki Tsuru, Shunsuke Kawano, Takeshi Ohgai, Hisaaki Fukushima, Shigeo Kobayashi, Tetsuya Akiyama

"Electrodeposition of Fe-Ni and Zn-Ni alloys from aqueous solutions is one of the well-known examples of anomalous codeposition in which less noble metal deposits preferentially. In this paper, the electrodeposition behavior of these alloy systems was compared between the methanol and aqueous baths. In Fe-Ni system, the significant suppression of the deposition rate of more noble Ni was observed over a wide range of electrolysis conditions in both methanol and aqueous baths. However, the electrodeposition of Zn-Ni alloys showed the typical feature of normal type codeposition in the methanol baths, which was completely different from that in aqueous sulfate baths. The difference in the electrodeposition mechanism between Fe-Ni and Zn-Ni alloys was discussed on the basis of the alloy deposition behavior in the baths in which the activity of water was varied:INTRODUCTION'It has been well known that Fe-Ni alloys show an excellent soft magnetic property. Therefore, thin films of this alloy have been used to fabricate the'-various magnetic devices. For the production of Fe-Ni thin films, dry processes such as sputtering, PVD and CVD are 'employed frequently and the resulting films showed a preferable property as a magnetic material. Electrolyses as a production technique of thin films, on the other hand, has the advantage over other processes in its cheaper production cost due to the simplicity of the production unit The Zn-iron-group metal alloys such as Zn-Ni and Zn-Fe electrodeposited on a steel sheet ale known to exhibit excellent corrosion resistance and therefore the electrodeposition of these, alloys has been applied to the production of surface treated steel sheets mainly for automotive body panels.According to Brenner (1), the electrodeposition behavior of Fe-Ni and Zn-Ni alloys was' classified into the' 'anomalous type. In this type of codeposition, less noble metal, i.e. Fe for Fe-Ni and Zn for Zn-Ni system, deposits preferentially and the change in -the alloy composition- with the variation of electrolysis conditions was unpredictable because of their obscure deposition mechanism. Since most properties of the alloys mainly depend on their composition, the composition of the deposited' alloys must be controlled strictly. Therefore, it is neces5al)' to clarify the mechanism of anomalous codepasition in Fe-Ni and Zn-Ni systems: Several mechanisms have been proposed so fur, and among them the hydroxide .suppression mechanism (2), (3) has been regarded most plauslble depend on their composition, the composition of the deposited' alloys must be controlled strictly. Therefore, it is necessary to clarify the mechanism of anomalous codeposition in Fe-Ni and Zn-Ni systems: Several mechanisms have been proposed so far, and among them the hydroxide suppression mechanism (2), (3) has been regarded most plausible. According to this mechanism, it can be predicted that the codeposition behavior depends greatly on the characteristic of water solvent in this study, using methanol as a solvent, the electrodeposition behavior of the anomalous codeposition was investigated to discuss the validity of the hydroxide suppression mechanism."

Jan 1, 2000