Search Documents

By V. D. Tathavadkar

Chromite ore is of immense importance for the extraction of metallic chromium and chromium chemicals. The mineralogy and crystal structure of chromite phase are therefore important part of our investigation on the extraction chemistry of chromium species. In this investigation, we have studied the effect of the processing parameters, i.e., the temperature and the oxygen potential on the microstructure and composition of mineral phases formed in the Cr2O3 ?Al2O3 -FexOy -MgO system. In particular the importance of the spinodal decomposition reaction is emphasized in the extraction of chromium as sodium chromite and sodium chromate. Experiments were carried out in order to study the differences in the crystallography of different chromite minerals. Phase equilibria in natural chromite minerals were investigated by calcining chromite mineral in air, argon, and 5% hydrogen + argon atmospheres over a temperature range from 200 to 1200 °C. The effect of the oxygen partial pressure and temperature on the phase constituents of the calcined product has been discussed. The microstructural changes were examined using scanning electron microscope (SEM) and the changes in elemental composition in different phases were analysed by electron probe micro analyser (EPMA). The results obtained from EPMA studies were used to calculate lattice parameter of the spinel lattice, and these values were compared with the values obtained from X-Ray powder diffraction data. On the basis of the experimental data, the mechanism of the spinodal decomposition of complex spinel phases is described under the influence of oxygen partial pressure and temperature.

Jan 1, 2000

By Natasa Mitevska

In order to ensure the minimal copper concentration in the reverb furnace slag, the graphical optimization method is used and the optimal slag composition of the reverberatory furnaces No.1 and No.2 in the RTB BOR, Copper Smelter and Refinery (Serbia) is obtained: (Si02) .. 38.0%; (FeO) .. 40.0%; (Fe3O4) = 5.0%; (CaO) = 5.0%; (Al2O3) .. 6.0%. Keywords: Optimization, Reverb Furnace Slag, Graphical Method

Jan 1, 2003

By Achilles J. B. Dutra, Carlos M. Juarez

"The use of thiourea as a gold leaching reagent has been extensively studied by many researchers, and it has proved to be promising for some cases as refractory ores. Otherwise, the recovery of gold from these solutions did not receive so much attention. In this paper the electrowinning of gold in acidic thiourea solutions was studied by voltarnmetry and chronopotentiometry. An adsorption step was detected prior to Au(I) reduction and the diffusion coefficients at 25°C for Au-TU complex and FD were found to be 1.00 x 10.5 cm2 S-I and 1.98 x 10-5 cm2 S-I respectively. At -0.350 V (SCE) a passivation probably due to TU adsorption was observed. For higher overpotentials hydrogen evolution was the main reaction.IntroductionThe use of acidic thiourea solutions for the extraction of gold and silver has shown to be a promising alternative to the traditional process of cyanidation, specially for certain refractory ores (1-3) and electronic scrap (4). In some cases, the industrial scale was reached (1,5). The thiourea leaching of precious metals presents advantages over cyanidation, as faster kinetics, lower toxicity and lower sensibility to base metals; however the costs due to high thiourea consumption impairs its use.The majority of the publications on thiourea processing of gold is on leaching. Many are review papers (5-7). Recently, the adsorption and desorption of the gold-thiourea complex on activated carbon and ion exchange resins have been studied (8-11).Little research has been done on the electrowinning of gold from acidic thiourea solutions, most of it has been carried on the seventies and beginning of the eighties in the former USSR (12-17) and concerned the eletrolytic extraction of gold in tridimensional cathode cells.The present paper concerns the cathodic behavior of the gold-thiourea complex in the presence of formamidine disulfide in order to provide information on the electrowinning of gold from solutions obtained directly from leaching or from an elution process."

Jan 1, 1997

By Xiao Yang

Calcium oxide is one of the major fluxing agents used for steel refining. Because unreacted CaO remains in slag in most cases, discharged slag is difficult to be recycled smoothly. With the growth of environmental concerns, improving utilization efficiency of CaO is required to reduce the amount of discharged slag and energy consumption. The authors have reported a resource and energy-saving process by using multi-phase flux for dephosphorization. Reaction behavior of phosphorus in multi-phase CaO–FeOX–SiO2–P2O5 flux system was investigated. Formation mechanism of P2O5-rich phases was clarified at the interface between solid CaO or 2CaO, SiO2 and molten CaO–FeOx–SiO2–P2O5 slag. Phase relationship and thermodynamic properties of 2CaO, SiO2-3CaO, P2O5 solid solution were observed to confirm the condensation of P2O5 in solid phase. Based on these results, reduction of CaO consumption, discharged slag curtailment, and energy-saving effects in the novel refining process by using multi-phase flux were discussed.

By Adelana Adetunji

Ilmenite ore samples obtained from Dankoli in Zamfara, North Western Nigeria has been characterized using Energy Dispersive X-ray fluorescence (EDXRF) technique, X-ray diffraction (XRD) technique and the Neutron Activation Analysis (NAA) technique. The major constituents in the ore were quantitatively found to be TiO2 and Fe2O3 in concentrations of about 60wt% and 31wt% respectively. These occur in the forms of magnesian ilmenite (Fe, Mg)(Ti, Fe)O3, pure ilmenite (FeTiO3), and barium copper yttrium oxide (Ba2Cu3YO6.56) minerals. Other constituents/impurities in minor or trace quantities include MnO, Ta2O5, Nb2O5, Wo, SnO2, Hf, Zn, V, Zr, Co, Pb, Br, Al, Rb, Y, Th and U.

Jan 1, 2006

By Liu Wei

In order to make clear the dissolving characteristic of the chrysocolla (CuSiO3?H2O) in the ammonia-ammonium chloride solution, a thermodynamic model of the chrysocolla (CuSiO3?H2O)-ammonia- ammonium chloride-water system is established using the exponential computation method based on both mass balance and charge balance equations. The equation group of the thermodynamic model is solved by the MATLAB Soft on PC. The condition which is favorable for dissolving high concentration of copper in solution is making out. The stable area of chrysocolla (CuSiO3?H2O) and the condition of chrysocolla (CuSiO3?H2O) converting to atacamite (Cu(OH)1.5Cl0.5) is also studied. A group of experiments are designed to validate the veracity of the results of the thermodynamic calculation.

Jan 1, 2010

By Cheng Pan, Xuewei Lv, Guibao Qiu, Chenguang Bai, Meilong Hu

"Physic-chemical properties of slag at high temperature play an important role in the pyrometallurgical process of production of ferronickel alloy. It determines the operation efficiency, metal recovery ratio, energy consumption and the distribution of elements like S and P between the slag and metals. In the present work, the effect of MgO content in the slag on melting features and viscosity of the slag was investigated. The MgO content in the SiO2-CaO-MgO-Al2O3 -FeO in the quinary slag system varied from 14.5% to 22.5%. The results shown that all slag samples begin to softening at the same temperature, the softening temperature, melting temperature, flowing temperature decrease with the increase of MgO content when the MgO content is in range of 14.5 and 20.5 pct mass, and when MgO content up to 22.5 percent, the temperatures increase sharply. Besides the inflection point temperature of viscosity-temperature curve increase with the increase of MgO when the MgO content is in range 16 and 22.5 pct mass.IntroductionNickel is very important to modern society, without it, we would not be able to share many things in our daily life, such as airplanes, computers and many stainless steel appliances in our homes and workplaces1.. It is the essential element of the stainless steel making, and about 65% of the nickel consumed in the world is used to make stainless steel2., so with the increase of stainless steel, the nickel production and demand has continued to increase3.Nickel is produced from two distinct ore types: nickel sulfide deposits and oxide nickel laterite deposits. The great majority of world’s known nickel resources are contained in laterite deposits3.. The laterite ores are normal classified into two groups: the high-iron laterite ore and high-magnesia laterite ore1. Typical composition of high-magnesia laterite ore is in the range 1-3%, and these ores are suitable for pyrometallurgical process to produce ferronickel4."

Jan 1, 2012

By Zhao-Qun Ke, Wen-Feng Tan, Jiang Diao, Yu-Hao Liu, Bing Xie, Zhang Tao, Wang Zhou, Hong-Yi Li

An effective way to decrease the dephosphorization burden in the current vanadium extraction-steelmaking process is slagging with CaO in vanadium extraction step. The phase composition of vanadium slag with different basicity and the regularities distribution of elements have been investigated by X-ray diffraction analysis and scanning electron microscopy combining with energy disperse X-ray spectrometry, respectively. The results indicate that V mainly concentrates in the spinel phases; Ca and P are rich in the silicate phases. Fe2SiO4 transform to CaFeSiO4, while the basicity of vanadium slag is 1.3. With further increase of basicity, 2CaOSiO2 could form in the silicate phases. Moreover, the phosphorus-containing phase will transform from Ca3(PO4)2 to Ca3(PO4)2-nCa2SiO4. With the increase of P2O5 content, the crystallization rate of spinels decrease obviously. Furthermore, the peak temperature for crystallization of spinels decrease 5 K with the P2O5 content increasing 1 wt%.

Mar 1, 2017

The viscosity of high magnesium content FeO-Fe3O4-SiO2-CaO-MgO slags at nickel flash smelting conditions was investigated using a commercial rotational viscometer. The studied parameters were compositions of slag and temperature. The viscosity of these slags was measured as a function of CaO, MgO, SiO2, FeO. Fe3O4 and Fe/SiO2 in temperature range from 1473K to 1723K. These slags contained 5.81 to 10.59 pct MgO, 0 to 10.37 pct CaO, 28.21 to 36.21 pct SiO2, 39.40 to 55.42 pct Fe and 1.1 to 1.5 Fe/SiO2.

Jan 1, 1999

By Neng-Wen Yu, Shau-Jun Zhu, Ji-He Wei

The desulfurization process by powder injection and blowing in the RH refining of molten steel and its mechanism have been considered and analyzed. Based on the two-resistance mass transfer theory and the mass balance of sulfur in the system, a kinetic model for the process has been developed. The related parameters of the model, including the mass transfer coefficients and the effective amount of powder in the molten steel being treated for desulfurization, have been more reasonably determined. Modeling and predictions of the process of injecting and blowing the lime-based powder flux under assumed operating modes with the different initial contents of sulfur and amounts of powder injected and blown in a RH degasser of 300 t capacity have been carried out using the model. The relevant circulation rate of the liquid steel and the powder injection and blowing rate were taken to be 100 t/min and 150 kg/min, respectively. The initial contents of sulfur in the liquid steel to be treated and the amounts of powder injection and blowing were respectively assumed to be 0.007, 0.006, 0.005, 0.004, 0.003, 0.002 mass-% and 10, 8, 6, 5, 4, 3 kg/t-steel. The total treatment time for desulfurization under each mode was set up at 24 min, equivalent to eight circulation cycles of the liquid steel to be treated. The results indicated that the predictions made with this model are in good agreement with some data of the industrial experiments and practice. Injecting and blowing the lime-based powder flux with the composition of 85 mass-% lime (CaO) + 15 mass-% fluorspar (CaF2) of 3-5 kg/t-steel, it is possible to decrease the sulfur content in the molten steel to ultralow level below (5-10)x10·4 mass-% from (60-80)x 10·4 mass-%. The total treatment time needed will appropriately be 12-20 min. Intensifying the powder injection and blowing operation and increasing the circulation rate of the liquid steel may effectively' raise the rate of the process in RH refining. The model may be expected to offer some useful information and a reliable basis for determining the reasonable process parameters and help in optimizing the technology of desulfurization by powder injection and blowing in the RH refining of molten steel.

Jan 1, 2000

By Shizhe Liu, Bing Li, Heng Wang, Zuxin Zhao

In this paper, cyclic voltammetry and chronoamperometry have been applied to investigate the effects of Nd2O3 concentration on the anode effects, critical potential for the anode effects and Nd2O3 reduction in LiF-NdF3-Nd2O3 melts at 950℃. The results show that the oxidation peaks in the potential of about 2.7V are attributed to the oxygen ions oxidation and the peak current density increases with Nd2O3 concentration increase from 0 to 0.5wt%. The critical potential caused the anode effects shifts to 0.3V more positive value as Nd2O3 content in the melts decreases from 0.01wt% to 0.5wt%. The cyclic votammograms on W electrodes in the LiF-NdF3-Nd2O3 melts present two pairs of reduction and oxidation peaks, indicating that the reduction of Nd ions in the LiF-NdF3-Nd2O3 melts in two steps rather than one step.

Jan 1, 2014

By I. Moscoso, R. Padilla, M. C. Ruiz

Antimony and arsenic are impurities in copper concentrates found normally as stibnite (Sb2S3), tetrahedrite (Cu12Sb4S13) and enargite (Cu3AsS4). When copper concentrates contain appreciable amounts of As and Sb, they must be removed before smelting to avoid environmental pollution. Oxidizing volatilization roasting at 500–700 °C has been used to eliminate these impurities. However, only a fraction of Sb volatilizes in those conditions; thus, a more effective process to eliminate antimony from concentrates is needed. In this study, the chloridizing roasting of Sb2S3 using CaCl2–O2 was investigated to remove the antimony from concentrates. XRD analysis of calcines indicated that the overall reaction could be written as: Sb2S3 þ3CaCl2 þ6O2 ¼ 2SbCl3 þ3CaSO4 Temperature and oxygen partial pressure have a significant effect on the rate of reaction. An estimated conversion of about 90% was obtained at 750 °C, 5.4% oxygen in 20 min. High oxygen concentrations arrest the advance of the reaction forming various antimony oxides including Sb6O13, Ca5Sb5O17 and Sb2O4.

Mar 1, 2017

By Yun Soon Han, Joo Hyun Park

Indium (In) solubility in the FeO-SiO2-Al2O3-5%CaO slag was measured under p(O2)=10¯¹¹ atm at 1573 K to clarify the dissolution mechanism of In in FeO-bearing metallurgical slag. The In solubility increased with increasing oxygen partial pressure, whereas it decreased by increasing the activity of basic oxide, viz. FeO. Thus, a dissolution mechanism of In in the FeO-SiO2- Al2O3-5%CaO slag was described by the following equation. In(s)+1/4O2(g)=(In+)+1/2(o2-) The enthalpy change of the In dissolution reaction was negative, indicating that the dissolution reaction was an exothermic reaction. This is consistent with the above reaction mechanism.

Jan 1, 2014

By Gökhan Hardal, Berat Yüksel Price

Nickel manganite based negative temperature coefficient (NTC) thermistors have good temperature sensor characteristics and electrical stability for temperature measurement applications. In this study, the electrical and microstructural properties of Ni0.5Co0.5Cu0.3Zn0.3Mn1.4O4 NTC thermistor were investigated. The samples were fabricated by the conventional solid-state reaction method. The powders were calcinated at 900 °C for 2 h and the samples were sintered at 1200 and 1300 °C for 5 h in air. The bulk density of samples was 5.07 and 4.96 g/cm3, respectively. The microstructure of samples was observed using a scanning electron microscope. The electrical resistance was measured in a temperature programmable furnace between 25 and 85 °C. The electrical resistivity of the Ni0.5Co0.5Cu0.3Zn0.3Mn1.4O4 sample increased from 52 Ω cm to 95 Ω cm when the sintering temperature increased from 1200 to 1300 °C. The material constant “B”, sensitivity coefficient “α” and activation energy “Ea” values were also calculated for the NTC thermistors.

Mar 1, 2017

By Zhang-Guang Gao, Ming-Mei Zhu, Rui-Rui Zhao, Chao Jiang

This paper focuses on the CaO-SiO2-FeO-MgO-MnO-P2O5 slag system that represents the major components of dephosphorization slag in BOF. Phosphorus distribution between 2CaOSiO2-3CaOP2O5 Solid Solution and Liquid Slag were analyzed by FactSage. The effects of slag content, basicity on the distribution ratio of P between the solid solution phase and the liquid phase (LP) and the percentage content of P in solid solution phase and liquid phase have been discussed. The results show that, with the increase of basicity, LP (wt%) decreases until the basicity reaches 1.9, then it turns to increase. LP (wt%) increases gradually with the increasing amount of FeO or P2O5.

Mar 1, 2017

By Uday Pal

In direct reduction processes for iron and steel making, significant amounts of Fe-C alloy droplets are generated and these remain suspended in relatively low FeO (around 5%) containing slags. Earlier workers have found that when the FeO content in the slag is <5%, the decarburization reaction becomes extremely slow (virtually ceases to occur) even though the alloy droplet contains a significant amount of carbons (2-3%). Understanding this rate controlling kinetic phenomena is crucial to designing an&apos; optimum direct steel making process. We studied decarburization of Fe-C particles by low FeO (<5%) containing CaO-SiO2A12O3 slags and found that by putting both the droplet and the slag in direct contact with an inert electronically conductive member that extends deep inside the slag bulk were able to quickly and completely decarburize the droplets. A detailed description and an explanation of the process will be presented.

Jan 1, 1995

By Clemens Schmetterer, Patrick J. Masset

"The surface tension represents an important property for the modelling of high temperature processes. In this study the surface tension of two Al2O3 – CaO – SiO2 model slags and the influence of the admixture of 5 up to 30 wt.% FeO were studied. The surface tension measurements were carried out using the sessile drop technique on BN substrates under Ar atmosphere (10-6 atm O2) up to 1500 °C.IntroductionThe aim of VIRTUHCON1 is the virtualization of high temperature conversion processes, a task that requires thorough understanding of these processes. In many of these conversion processes slag plays an important role to control the properties of the product, to protect the reactor lining or simply as waste. Slag surface tension is one of the materials properties that is needed for the description of such processes, since it influences the interactions between the components in the reactor, e.g. at the slag – Fe interface in the blast furnace.Surface and interfacial tensions have thus received considerable attention in research, but the number of investigations in this particular pseudo-quaternary system is surprisingly low. Furthermore, the literature data are subject to different measurement conditions and techniques which complicates the data analysis and comparison.The slag atlas [1] offers a compilation of the available literature until 1986 (shown in Table I), but literature search has not revealed more recent studies of this system until now. For example, Elliott and Mounier [2] determined the surface tension of ACSF slags using the double tube maximum bubble pressure technique at 1200 °C. They kept their slags in contact with Cu-S-F mattes, and the slag therefore contained a certain amount of sulphur which acts as a surfactant and lowers the surface tension. The compositions of their slags were scattered over a wide composition range and they did not use a common ACS base mixture for their tests, either. The surface tension values vary between 417 and 446 mN/m, but due to the reasons just mentioned no trend in the measurements can be observed and the influence of FeO admixture on the surface tension cannot be deduced. Further information including the temperature dependence is available from Pavlov et al. [3], Ishchanov and Shushkov [4] and Murav’eva and Kaplun [5]; the diagram on page 446 in Ref. [1] has been drawn from these sources. Both positive and negative temperature coefficients are reported in these works. SiO2 is the only pure constituent that has a positive temperature coefficient [6], but a correlation of the temperature coefficient with the SiO2 content was not found to be conclusive."

Jan 1, 2011

By Dirk Verhulst

The Altair Hydrochloride Pigment Process is a new ?third route?, besides the established high-temperature chloride process and the older sulfate process, to manufacture TiO2 pigment from ilmenite ore. It has been tested at a scale of 5 t/day feed. The ore concentrate is digested in high-acid, high total chloride solution (+/- 39% Cl). Titanium and iron both go into solution. Iron is separated as FeCl2 crystals after reduction and cooling. Titanium is transferred by solvent extraction into a purified, high-Ti stream. It is spray-hydrolyzed to produce a TiO2 hydrate and further calcined with additives into high-quality pigment. HCl solutions generated by pyrohydrolysis and spray hydrolysis are treated by pressure-swing distillation to regenerate HCl gas for re-injection into the digestion reactor. All chloride streams are recycled. Recent work has concentrated on optimization, particularly in 3 areas: - Solvent extraction: a new organic mixture, including a new diluent, makes it possible to work at room temperature, to avoid TiO2 hydrolysis problems and to improve phase disengagement and impurity separation. - Pigment finishing: a systematic study of the parameters involved, followed by long runs in the best conditions confirm pigment quality. - Flow sheet optimization: innovative modifications of the conditions of spray hydrolysis and pyrohydrolysis, combined with re-routing of streams achieve significant energy savings. A 100 t/year pilot plant including these features as well as other process improvements is under construction.

Jan 1, 2006

By Melinda Channel, Alan W. Weimer, Jonathan R. Scheffe

"There is a need to develop cost effective renewable energy processes for the production of clean fuels that can simultaneously mitigate the U.S. energy/global environmental security issue. If H2 can be obtained cost effectively via the splitting of water using concentrated sunlight, then it’s possible to operate a fuel cell using renewable H2 or to synthesize other fuels based on renewable H2 for generating electricity or for running internal combustion engines. For example, H2 can be reacted with sequestered carbon dioxide (CO2) to produce syngas (H2/CO) via reverse water gas shift (RWGS), i.e. H2 + CO2 ? CO + H2O. The syngas can be catalytically methanated to form synthetic natural gas (SNG) or it can be catalytically reformed to produce liquid fuels such as “green” gasoline via the MTG process (syngas? methanol ? gasoline). The desert SW United States is home to world class sunlight. Fundamental ferrite thermodynamics will be reviewed, an example of the beneficial effect of ferrite surface area on reaction kinetics will shown, and process economics will be investigated for a 100,000 kg/day facility to produce H2.Introduction and Background ThermodynamicsSpinel ferrites of the form MxFe3-xO4, where M generally represents Ni, Zn, Co, Mn, or other transition metals, have been shown to be capable of splitting water according to the two step cycle shown below:MxFe3-xO4 + solar thermal energy ? xMO + (3-x)FeO + 0.5 O2 (1)xMO + (3-x)FeO + H2O ? MxFe3-xO4 + 2H2 (2)This is an inherently clean and sustainable process, as the only net inputs are solar energy and water, and the net outputs are hydrogen and oxygen. Ferrite water splitting cycles are advantages compared to other high temperature water splitting cycles, such as the ZnO/Zn and Mn2O3/MnO cycles, because thermal reduction has been demonstrated at significantly lower temperatures[1, 2]. As a result, overall efficiency may be increased due to the fact that radiation losses increase as the fourth power of temperature, and material considerations for reactor design should be more flexible. Additionally, cycle repeatability has been demonstrated with relative ease as compared to other thermochemical cycles [3-6]. However, the amount of hydrogen per mole that is generated is significantly less than for other high temperature thermochemical cycles due to the fact that only Fe3+ is capable of being reduced at the temperatures of interest[6]. In addition, water oxidation kinetics appear to be very slow, likely due to diffusion or surface area limitations created by near surface oxidation [6, 7]."

Jan 1, 2010

By K. A. Elbarawy

Processing of Egyptian barite ore with a composition of 85.5% BaSO4; 2.75%SiO2;1.56%Fe2O3 and 5.1% Al2O3 was performed with the aim to prepare pure barium salts. The process took place through pelletization-solid state reduction and leaching steps. Each of these steps was optimized. Pure barium sulphate (99% < 0.82µm) and carbonate (99%<0.75µm )were the final products. This article deals with the reduction process that occur whn coal was added to the ore during pelletization in the ratio of 5:1 stoichiometry. Optimum reduction of pellets of 8-12mm in diameter was achieved after 60 minutes at 1050oC and under a rate of 5 lmin-1 of nitrogen atmosphere, where 87.79% of the ore was reduced. The kinetic studies showed that the reduction process could be modeled according to the core mechanism of diffusion control in which the effective diffusivity is based on the surface area of unreacted ore. The activation energy calculated was 92.7 kJmol-1.

Jan 1, 2006