Search Documents

By Dengfu Chen, Mujun Long, Youguang Ma, Xin Xie, Xing Zhang, Leilei Zhang

"Processing parameters of a submerged entry nozzle (SEN) affect significantly on the patterns of fluid flow and temperature distribution in beam blank continuous casting mold with double SEN s. Effect of the geometry structure and immersion depth of double SEN s on the fluid flow in beam blank continuous casting mold was studied by water modeling. Results showed that, the optimal nozzle inner diameter was 40mm, and immersion depth was 70-90mm. The mold surface fluctuation, slag distribution, impact depth and removing rate of inclusion particles were discussed under different processing parameters of double SENs. As the results indicated, slag distribution was more non-homogeneous with a higher casting speed. The results provided basic data for the design and optimization of SENs used in beam blank continuous casting mold.IntroductionNear-net-shape casting has the distinct advantages of less rolling procedures, higher metal recovery and lower energy cost. Therefore, in the recent decades, one of the recent trends in the steel making process is moving toward near net shape casting. in which beam blank casting is a typical technology. The schematic section of beam blank is shown in Fig 1."

Jan 1, 2014

By Joel Anderson

Allvac 718Plus is a newly developed superalloy with a good potential for use in fabricated aircraft engine structures when service temperatures exceed 650°C; the limit for standard alloy 718. Fabrication involves welding, where cracking usually is a prohibitive factor. Comparison of the solidification cracking behavior between these two alloys was made by Transvarestraint testing. It was shown that the total amount of cracking was significantly lower for 718Plus alloy, which was associated with a lower amount of ?/Laves or ?/NbC eutectic-type constituents. This in turn is believed to be due to the lower iron content of the Allvac 718Plus material. The analysis of alloying element segregation both within primary dendrite and interdendritic constituents clearly indicates that the segregation of Nb is the controlling factor in determining the final solidification microstructure in these alloys. The Nb concentrations of these constituents are significantly higher compared to the bulk alloy concentration. This was confirmed by the SEM-EDS analysis and calculations assessed with JMatPro, the latter also indicated that alloy 718 is more prone to form Laves and NbC eutectic-type constituents compared to Allvac 718Plus material.

Jan 1, 2008

By Ma Ying

The continuous directional solidification technique of five kinds of special ZA alloys with eutectic, peritectic and eutectoid transfonnation under the condition of continuous casting by heated mold was studied. The mechanism of surface defects appearing in ZA alloy line was discussed and the structure of some defects were analyzed by SEM. The results show that only when the fitting of various technique factors, pressure head, outlet temperature, pulling speed and cooling condition are reasonable under a certain range, can the ZA alloy smooth line be continuously pulled out. Unreasonable techniques will result in hot tear, rough surface, mush outlet, leaking and other defects. The shape and location of solid-liquid zone have an important influence on the formation of the above defects. When the solid-liquid zone is located in the mould outlet or inner mould, the surface of solidification will protrude into the inner mould. If the remaining liquid cannot counteract the solidification contraction, a rough surface will appear. If the solidification surface further into the mould, the ingot in the mould will have a great friction force when pulling and will form a hot tear. When the solid-liquid zone is moved out of mould, the solidification surface will turn into a plane, which easily results in leaking. A vibration or unstable operation will cause an ingot winding during pulling.

Jan 1, 2003

By J. M. D. Wilson

An analytical program using a combination of SEM-based image analysis techniques is developed for automated modal analysis of ores containing silicate and other gangue minerals. Previous knowledge, gathered by means of either optical microscopy, X-ray diffraction, SEM, or electron microprobe analysis is used to establish discrimination criteria in the image analysis program. The program initially discriminates minerals on the basis of their relative grey values in a backscattered electron image. For those minerals which have overlapping grey levels the minerals are identified by the program using energy dispersive X-ray spectrometry with X-ray counting for twelve or more elements. This technique is useful to quantify ores in which the gangue minerals are numerous. Two cases of application are presented.

Jan 1, 1999

By Carlos Maurício. F. Vieira, Lázaro A. Rohen, Sérgio N. Monteiro, Rafael G. de Castro, Gustavo X. Borges, Maycon A. Gomes, Frederico M. Margem, Anna C. C. Neves

Economic and environmental benefits are motivating studies on natural fibers, especially lignocellulosic extracted from plants, have been studied to substitute synthetic fibers, such as glass fiber as reinforcement in polymer matrices. By contrast to synthetic fibers, natural fibers have the disadvantage of being heterogeneous in their dimensions specially the diameter. About the hemp fiber, little is known of their dimensional characteristics. The aim of the present work was to statistically characterize the distribution of the diameter of hemp fibers. Based on this characterization, diameter intervals were set and the dependence of the tensile strength of theses fibers with a corresponding diameter was analyzed by the Weibull method. The diameter was measured with precision using a profile projector. Tensile tests were conducted on each fiber obtain mechanical strength. The results interpreted by Weibull statistical showed a correlation between the resistances of the fiber to its diameter.

Jan 1, 2015

By Andre Krzysik

"Fluidized bed technology has been used in the industry for almost 100 years. To fully understand the process hundreds if not thousands of researchers were and are involved in finding the way to predict the behavior of the solids when subjected to the flow of media through them and the conditions of the solids in the fluidized state. The difficulties in predicting the behavior of solids in the fluidized state stem from the complexity and abnormality of the parameters related to the solid particles. Theoretical calculations can in some degree account for some of them. Particle size distribution, their shape, density, moisture content and physical and chemical reaction that may exist in the fluidized bed reactor play an extremely important role and influence the behavior of the fluidized bed. This paper focuses on the practical examples of the fluid bed equipment and the use of different conditions to process various products.IntroductionEach process application has its own unique requirements and the designers of the equipment must take into consideration specific process requirements, specific properties of the material to be processed (both physical and chemical), and physical and chemical reactions/changes that are taking place in the reactor (heat and mass exchange, chemical reactions, isomorphic change etc.). Each individual piece of equipment must also satisfy specific requirements/ preferences of the client that will operate and maintain the equipment. Those often represent greater challenges than the process on its own, and are equally important to the satisfactory operation of the plant. That includes aspects like location of the equipment, environmental effects, and expected life of the equipment, process control, access, maintenance, and many others.Over the period of time a great deal of research, both theoretical and practical have been carried out and the results of that work are available for equipment designers. For the simple applications that information is usually sufficient and the selection of a suitable solution is relatively simple. In many instances, the available information is not sufficient, and often specialized test work needs to be conducted to obtain additional data. In many cases a pilot installation is built in which the required process is tested. Only then the commercial equipment is designed. The following deal with specific installations that were designed to satisfy specific requirements. In some instances, additional problems were discovered during the commissioning of the equipment that required on site modification. The continuous monitoring of the equipment that was supplied to the various clients allowed us to further develop and improve our designs."

Jan 1, 2014

By John R. Hugens

Modifications in the ALSCAN method of measuring hydrogen dissolved in liquid aluminum have made it possible to monitor the level of hydrogen dissolved in liquid copper. Measurements from the tundish show a correlation with eddy current readings from the continuously cast and rolled copper rod from the continuous casting and rolling system at Amarillo. The measurements also indicate that the copper in the tundish is supersaturated with hydrogen.

Jan 1, 1994

By Do-Hyeong Kim, Tae-Jung Kim, Seung-Yeon Won, Jong-Jin Pak, Min-Kyu Paek

Liquid iron alloys containing V, Mo, and Ni can be produced by the carbothermic reduction of spent catalysts used in petrochemical industry. Thermodynamics of carbon in these alloy melts is important for refining these alloys. In the present study, the carbon solubility in Fe-V, Fe-Mo, Fe-Ni, Fe-V-Mo, Fe-V-Ni, Fe-Mo-Ni and Fe-V-Mo-Ni alloy melts of various compositions was measured at 1873 K. The temperature dependency of vanadium effect on carbon solubility in liquid iron was also measured in the temperature range from 1823K to 1923K. The additions of vanadium and molybdenum significantly increased the carbon solubility in liquid iron alloys while nickel decreased the solubility. The experimental results were thermodynamically analyzed using Lupis’ relation at constant activity to determine the first- and the second-order interaction parameters of vanadium, nickel and molybdenum on carbon at carbon saturated condition. Using thermodynamic parameters determined in the present study, the carbon solubility in Fe-V-Mo-Ni alloy melts of various composition were accurately predicted and verified experimentally at 1873 K.

Jan 1, 2014

By Leandro Voisin

A new pyrometallurgical treatment alternative is proposed for cleaning complex copper matte with high content of impurities in the copper smelting process, thus, in a suitable furnace, a given amount of pig iron will be added to the liquid complex matte with a matte grade between 65 and 75 % Cu under reducing condition and will produce three liquid phases of matte, copper-rich alloy and iron-rich alloy. Hence, in this study, firstly, a mass balance calculation was made on the basis of the reported data for the distribution ratios of the components among the three phases to define the optimum condition where most of the arsenic can be fixed in the less valuable liquid iron-rich alloy. By taking advantage of the high concentration of arsenic in the iron-rich alloy, the small volume alloy may be disposed in a yard, while the precious elements may be recovered effectively in the liquid copper-rich alloy and/or in the liquid matte. Secondly, laboratory-scale experiments were conducted to apply the proposed process to the matte produced from the slag-cleaning electrical furnace and the Teniente Converter of the Codelco-Norte smelter. The obtained results indicate that the proposed process for cleaning complex matte is promising.

Jan 1, 2006

By Sumantra Mandal

The hot deformed microstructure of the 15Cr-15Ni-2.2Mo-Ti modified austenitic stainless steel (commonly known as alloy D9) was investigated employing electron backscatter diffraction (EBSD). Hot compression tests were conducted in a Gleeble thermo-mechanical simulator at temperatures of 1173K-1373K (in steps of 100K) with a strain rate of 10 and 100 s-1 to different strains. Various kinds of deformation patterns were observed inside the deformed grains. These were inferred as the development of geometrically necessary boundaries or formation of parallel set of micro-bands. Recrystallized grains were partitioned from the deformed grains employing grain orientation spread approach. Extent of dynamic recrystallization (DRX) was found to be minimal at 1173K. DRX was predominantly found to happen at and above 1273K which increases with increase in strain. DRX nucleation and development mechanisms were discussed with respect to bulging of the parent grains and sub-grain rotation. Special emphasize is given on the role of annealing twins on DRX nucleation and subsequent expansion.

Jan 1, 2009

By Viktor. P. Popov, Oleksandr. V. Derev'yanko, Oleksandr. I. Raychenko

"This paper is devoted to scrutiny problem of obtaining electro-contacts by electro-discharge sintering technology. A new unconventional method of electro contacts production (on Aggraphite base) can yield essential optimization resource.Review of three electro-technological methods of processing contacts materials is presented:- using graphite powder cladded by Ag;- mixture of graphite powder(which is a non-cladded powder) with Ag powder and addition of Fe powder particles;- method of infiltration of melted Ag into graphite piece without deformation and rupture of object.This technological approach can give the possibility to increase of compression strength of electro-contacts materials up to 340 MPa and more under conditions of additional reinforcing components (for example, by Fe).IntroductionThe electric current can be an active ""participator"" of the powder metallurgy technology [l]. At the passage of electric current through powders or some powder mixtures the phenomena including phase transformations arise. Here such effects, which are observed in the Ag-graphite and Ag-Fe-graphite powder mixtures and in the pair Ag-porous graphite, are described.The Ag-graphite composition materials (CM) are used, for example, as electric contacts [2, 3]. Since a material being produced is destined for the contacts it is necessary to take into account the following aspects: commutating current, its character and voltage, active or reactive character of working load, geometrical dimensions of contacts, quantity and frequency of switching on and switching off, pressure on contacts, distance between contacts, method of arc control, surrounding medium, its content, pressure and temperature. Thus, these and, maybe, choice of some other circumstances influence design, materials and production technology of contacts. The range of problems concerned dictates such steps as alloying of contact materials, optimization of structure, selection of kind of graphite, its connection with metal [4-10]. It is expedient to recall the main procedures of the first stage of the conventional technology: dosage of the initial graphite powder and binder-phenolic resin plastic varnish (for example, Bakelite), mixing, densification, thermal treatment, crushing, grinding, sieving, drying, dosage of grained graphite, dosage of the initial silver powder, obtaining of the silver salt solution, settling of salt, filtration, washing, drying of the cladded graphite powder, thermal treatment, obtaining of the graphite powder of particles cladded by silver. The second stage of the convectional technology starts by obtaining of the cladded graphite powder and finishes by annealing of the pressed blanks (Fig. 1)."

Jan 1, 2004

By A. V. Tarasov, A. D. Besser

A processing flowsheet has been developed for treating substandard lead-containing polymetallic bulk concentrates and intermediate flotation products containing precious metals, which comprises oxidizing roasting in a calcination kiln and electrothermic smelting generating low volumes of off-gas. The proposed flowsheet also incorporates a dust collection system and sulfur dioxide recovery from off-gas. It is proposed to implement this process by using a reaction smelting technique. For this purpose, the charge to be fed to the smelting furnace after its calcination in a drum-type rotary kiln must have a ratio of sulfide sulfur to sulfate sulfur of at least 1 :2. Electric smelting makes it possible to produce lead bullion that also collects the precious metals contained in the feed, as well as copper-lead matte and slag containing zinc. The recovery of lead into lead bullion and into matte is approximately 83% and 14%, respectively (thus the overall recovery is 97%); the total recovery of gold and silver into lead bullion and matte is 98%; th\lt of copper into matte is 89%; the recovery of zinc into slag is 96%; and that of sulfur into sulfuric acid or gypsum is 90%. After the recovery of zinc from slag, the latter can be utilized in the construction industry.

Jan 1, 2000

By Larry M. Southwick

There is much ongoing work in research and development of new processes for the recovery and recycling of met.a.ls and other materials from various waste and scrap streams. Commercialization of such new technologies requires the bringing together and successful execution of a considerable effort involving a variety of activities. These include process conceptualization, research and development, detailed design and construction, and then plant startup and operation. Processes evolve through all of these steps by engineering due diligence, making objective and critical analyses of results, and troubleshooting processing steps to, hopefully, arrive at a sequence that has the best chance to succeed operationally and economically. After a summary review of the above steps, several processes will be described in more detail that provide mostly successful examples of the above procedures. Finally, some observations will be made on areas that will become critical in the near future to the success of new processes for wastes and residues.

Jan 1, 2000

By Sepideh Abolghasem, Juan Pablo Casas Rodriguez, Juan Camilo Osorio

Predicting flow stress at high strain-rates is a desirable practice for material behavior characterization. Sub-grain size has shown a huge influence in cutting forces and the workpiece surface finish determination during orthogonal cutting process. Hence, a prediction of flow stress as a function of thermomechanical conditions and sub-grain size is of great important which is studied in this work for OFHC copper. The principal thermomechanical conditions being strain, strain-rate and the accompanying temperature rise are characterized in Plane Strain Machining (PSM) and the resulting microstructure, sub-grain size, is quantified. Material maximum flow stress (a constitutive model) as a function of thermomechanical conditions and sub-grain size is predicted considering a saturated state in microstructure using optimization algorithms for reaching the validated temperature rise based on modified Hahn’s model. Evaluated models suggest a major influence of strain-rate and dislocation in temperature rise estimation and flow stress prediction leading to consideration of mechanical failure phenomenon involved in machining-based manufacturing processes.

Mar 1, 2018

By Garrett May

We present a periodic technique for measuring the thermal conductivity of thin, disk-shaped samples. In samples of this type, temperature measurements must be made across the sample faces and are therefore subject to large error due to the interface resistance between the temperature sensor and the sample. The technique uses measurements of the amplitude and phase of the periodic temperature across both a reference sample and the unknown material at several different frequencies. Modeling of the heat flow in the sample allows the simultaneous determination of the thermal parameters of the sample as well as the interface resistance. The technique is demonstrated on nanocomposite samples less than 1.0 mm thick.

Jan 1, 2008

By Herman Wotruba

Mercury emissions and other environmental impacts in small-scale gold mining are a world-wide problem. "Clean" or better: "Cleaner" technologies have -apart from being environmentally sound -to guarantee a higher income and better working conditions for the miners in order to have a chance for long-term acceptance. In small scale primary gold mining in several South American countries, a number of techniques have been adapted and improved so that they not only were accepted due to their efficiency and easy handling, but they could also significantly lower mercury emissions.

Jan 1, 2003

By U. Kammer

The reduction of the lead content in the separator fraction produced during the mechanical processing of spent lead-acid batteries is an important environmental and economical issues. The reduction of lead down to less than 1 percent is very difficult using hydroseparators that are common in battery recycling facilities. Very promising results were achieved performing experiments on a test rig using a new technology in battery treatment: a discharge-type jigging unit. The materials is fed onto the jigging bed and transported through the machine. Due to the intensive movement of the feed, an additional washing effect is also obtained in addition to separation of the lead and plastic fractions. The knowledge gained from this development work at UVR-FIA GmbH in Freiberg, Germany, led to a patent application. This paper focuses on the results of the development work and the start-up and one year's operation of the industrial-scale application at Harz-Metall GmbH in Goslar, Gennany.

Jan 1, 2000

By W. F. Whittaker

Systematic control of process parameters during electrorefined copper cathode production and final product inspection ensures high quality of produced "ORC brand copper. Since 1986, substantial increases in tankhouse productivity have been achieved by a number of technological and process control changes. This paper reviews the changes implemented to achieve higher productivity and cathode quality.

Jan 1, 1992

By W. G. Davenport

Chapter 13 evaluated the %02 in blast, industrial oxygen and oil requirements for smelting FeSrCuFeS2 concentrates~ This chapter examines high eu grade CU2S-CuFeS2 concentrates the same way.

Jan 1, 2001

By Martin Brueggemann

In 1993, the El Paso Smelter began operation of the first commercial CONTOP copper smelting furnace. The CONTOP process was chosen for the plant modernization due to its low capital cost and the ease that it could be incorporated into a 100 year old existing smelter. After four years of operation, CONTOP has proved itself to be a reliable copper smelting technology. This paper will discuss a brief start-up history, current operation, and future modifications and improvements.

Jan 1, 1998