Search Documents

By K. Osseo-Asare

Rate laws for the hydrogen reduction of metal ions are typically of the form: [r = -d[M(II)]/dt = k[M(II)]xPy2H] where k is an apparent rate constant, [M(II)] and PH2 represent dissolved metal concentration and hydrogen pressure respectively, while x = 0 - 1 and y = 0.5 - 2. Half-order dependences have been reported for some M(II)/H2 systems; however, no satisfactory explanations have been offered. In an effort to bridge this gap in our understanding, the published precipitation rate data (for M(II) = Cu(II), Ni(II), and Co(II)) are reviewed (with emphasis on the reported reaction orders) and compared with the corresponding but limited electrochemical polarization data. Based on the available literature on the electrochemical kinetics of the M/M(II) and H2/H+ systems it is demonstrated theoretically that, under certain conditions (e.g., in the presence of electron-conducting solids), the rate of the M(II)/H2 reaction can be expressed as: [-d[M2+]/dt = k[M2+]2/1P2/12H] It is concluded that electrochemical processes probably play an important role in the hydrogen reduction of metal ions, especially for systems that involve heterogeneous catalysis.

Jan 1, 2003

By F. Guevara

The paper presents results of physical and turbulent three-dimensional numerical simulation of the gas flow in the wind box and reaction shaft of the concentrate burner of a flash furnace. Physical simulation work was carried out in a 1:5 linear scale model, where the velocity field was measured using a Pitot tube. The mathematical model consists of the three-dimensional averaged Navier-Stokes equations, turbulent kinetic energy and dissipation of turbulent kinetic energy using the Renormalization Group (RNG) theory for the k-e turbulence model. Computations were performed using FLUENT, based in a finite- volume code. The geometry of the concentrate burner was separated in two sections: wind box and reaction tower. Results obtained at the exit of the wind box were used as boundary conditions for the reaction shaft. The effect of boundary conditions on the numerical results was also studied. Results of physical and numerical simulations show an asymmetry of the velocity field at the exit of wind box. This asymmetry is possibly due to existence of a separated flow in the back of the exit ring. The agreement of physical and numerical results assess the capacity of the turbulence RNG k-e model to reproduce correctly the behaviour of the velocity field at the exit of the concentrate burner.

Jan 1, 1999

By María Cristina Ruiz

In the processing of copper concentrates by the conventional smelting-converting technology, complying with the increasingly severity of environmental legislation in some countries has become difficult, mainly due to severe fugitive emissions of gases produced during the batch PS (Peirce-Smith) converting step. In this work, the results of an investigation on the pressure leaching with sulfuric acid and oxygen of white metal (produced in a Teniente Converter reactor) are discussed. The study was carried out at laboratory scale and the main variables studied were temperature, concentration of sulfuric acid and partial pressure of oxygen. The experimental results indicated that most of the sulfur in the white metal was oxidized to sulfate in the whole range of temperature studied (105ºC to 150 ºC). The concentration of sulfuric acid over 0.05 M, and oxygen partial pressure over 6 atm had little effect on the dissolution of copper from the white metal. On the other hand, temperature had the most significant effect on copper dissolution; below 130 ºC copper dissolution was incomplete after 5 hours of leaching while at 150 ºC the dissolution was complete in 90 minutes and 10 atm of partial pressure of oxygen

Jan 1, 2006

By Marco A. S. Aguiar, Luis G. S. Sobral, Vânia Mori, Paulo A. Medeiros da Silva

"Copper occurs in the crust of the earth, predominantly, as sulphides. Among the copper sulphide minerals, the chalcopyrite is the most abundant and the most refractory to the conventional oxidative processes. This work aims at developing an electrolytic process for treating a copper sulphides flotation concentrate, more precisely chalcopyrite (CuFeS2) and bornite (Cu5FeS4) in the percentages of 70 and 30%, respectively.This paper presents a low-cost operational electroleaching process for treating copper sulphides flotation concentrates, with a high chalcopyrite content. This research practical work aims at improving the copper extraction from that sulphide mineral, in a relatively short time with low-operating cost taking into consideration the influence of a cationic surfactant. The electrolyte of the electrolytic reaction system was a 2,0 mol.L-1 NaCl solution containing CTAB, a cationic surfactant. The electroleaching system contains one DSATM (dimensionally stable anode) anode and two nickel or copper foams (threedimension electrodes. During the electroleaching process the chloride ions are oxidized to chlorine at the anode surface, which in contact with the aqueous phase generate enough hypochlorite ions to oxidize chalcopyrite.The copper ions released from the chemical oxidation process are reduced at the cathode surface as metallic copper."

Jan 1, 2008

By Chen-Ming Kuo, Esher Hsu

Energy recovery of livestock waste can not only reduce waste pollution but also generate renewable energy and further create economic bene fits. Currently, most of livestock waste in Taiwan is treated as waste without efficiently recycled. This paper aims to explore and evaluate the energy recovery of livestock waste in Taiwan and further provide policy suggestions. Study results show that small farming scale of livestock industry in Taiwan leads to a lower efficiency of biogas energy recovery. Besides, the environment with relative low price of electricity and high invest cost for power generation plant is hard to provide incentive for implementation of energy recovery which has further caused difficulty on policy promotion for renewable energy recovery of livestock waste in Taiwan. Policy reform with increasing FITs and differentiated purchasing rate for biogas power is suggested to stimulate energy recycling of livestock waste in Taiwan.

Mar 1, 2017

By V. A. Bryukvin

It has been found that by superimposing symmetric alternating current over the process, the rate of nickel and cobalt leaching from metallized products with copper sulfate solutions increases by a factor of 1.5 to 2.0 and the apparent activation energy of the process investigated is reduced from 12 down to 6.6 kcal/mole. It appears especially attractive to use alternating current for anodic dissolution (oxidation) of metallic scrap of refractory metals and their alloys in ammonia electrolytes permits production of high-grade commercial products in the form of respective ammonium salts using a short and virtually reagent-free process flowsheet. Similar approaches can be applied also for electrochemical processing of nickel and copper scrap in sulfuric acid media with subsequent recovery of pure sulfate salts or electrolytic processing. Electrochemical technology for recycling of tungsten-cobalt (WC 15) and tungsten-rhenium (WR 20) alloys has been also investigated. In the former case, anodic oxidation of carbide alloy was carried out in nitric acid electrolyte with production of pure tungstic acid. The research conducted has indicated that the physicochemical effect of alternating current results in a lower activation energy of electrode reactions due to changes in the mechanisms of the electrode reactions themselves.

Jan 1, 2006

By Viviane Tavares de Moraes, Denise Crocce Romano Espinosa, Jorge Alberto Soares Tenorio, Adriana Johanny Murcia Santanilla

"Increasing volumes of solid waste are generated worldwide, due to the continuous technological advances, the electronic scrap is part of these waste, requiring the study of recycling processes to stimulate this activity or the reuse of its components. The separation of nickel from sulphate leach solution, which also containing iron, zinc and aluminium was carried out using bis-(2,4,4-trimethylpentyl) phosphinic acid (Cyanex 272) as extractant, in order to determinate the effects of pH and temperature. The number of stages required for extraction was also assessed. The results showed that the metal extraction increased with increasing pH. On the other hand, increasing temperature was not favorable for all metals. However, under conditions used in this paper the purification of solution containing nickel was possible.IntroductionIncrease in the demand of metals in the world for use in industry causes a great exploration of natural resources. One outcome of this is increased investigations for the recovery of metals from industrial wastes. Nickel is found in wastes, such as batteries and electric and electronic devices, this kind of waste becomes a significant source for metals recovery. Since nickel is also present in printed circuit boards, which are associated with electric and electronic equipment, it can be recovered from this kind of waste through different techniques. It is important to highlight that iron is generally associated with this scrap [1] and for its removal chemical precipitation is often used. On the other hand, the solvent extraction process is widely used for treatment of leach liquors, because it can be produce high purity solutions [2, 3]. This technique is based on the purification of solution using contact between a liquor leaching and the immiscible organic solution, which contains an extractant that promotes the desired metal transfer [4]."

Jan 1, 2012

By Djalma Souza, Felipe Perissé Duarte Lopes, Frederico Muylaert Margem, Sergio Neves Monteiro

The development of composite materials is a combination of distinct materials, with applications in various areas, such as: aerospace, automobile, etc. Regardingmechanicalresistance,composites reinforced with a dispersion phase in a fiber form is more relevant. The green idea is use composites with natural fibers instead offiberglass, especially in non-structural applications. The Fique fiber has occupying an important place at Colombian agricultural and agribusiness sectors. Epoxy matrix composites reinforced with 1–6 Fique fabric layers were tested and the results indicated that thetensile properties improve with increasing theamount of Fique fabric layers. The fiber/matrix interaction was analyzed by scanning electron microscopy.

Mar 1, 2018

By Shaolong Chen, Carl-Gustav Berg, Hannu Mansikkaviita

Kumera Steam Dryer has been developed particularly for nonferrous metal concentrates with steam as heating source generated from waste heat boilers. Its unique structure enables the dryer to work at high capacity, up to 240 t/h, and high availability, over 95%. With half a century of engineering experience, and more than twenty industrial steam dryer installations worldwide during last 15 years, Kumera has demonstrated significant benefits of the steam drying technology in terms of energy efficiency and emission reduction to the end users. The dryer of this type can also be applied for other suitable mineral materials.

Jan 1, 2015

By Lin Zhu, Zheng Wei, Meng Li, Xueli Cao, Hanying Wen, Guodong Shi, Lei Yu, Wen-xin Tang, Tao Li

Low energy electron microscopy and photoemission electron microscopy (LEEM/PEEM), as powerful in-situ surface-sensitive electron microscopy, find wide applications in surface physics, chemistry and catalysis. The high reflectivity of incident low-energy electrons (0–100 eV), allows it to image the surface structures in the topmost few atomic layers within less than one second, while the sample can be heated up to 1200 °C in real time which is potentially very useful in metallurgy and materials fields. A unique three-prism aberration correction (ac-) LEEM was commissioned successfully in Chongqing University, with a lateral resolution below 2 nm. A multiple gas source in the ac-LEEM system was installed as well, which allowed us to observe chemical reactions of nanoscale mineral powders on metallic substrates. In this paper, the latest results on the applications of this three-prism ac-LEEM on oxidation and reduction processes on copper and iron polycrystalline surfaces are demonstrated.

Mar 1, 2018

By F. Sakurai

The enlarged Mitsubishi process in Naoshima has been in steady operation since. May 1991. However, the sulfuric acid plants have been in operation for more than 30 years. The acid plants were modernized between 1999 and 2001 by renewing some of main equipment such as the drying tower and gas heat exchangers, and introducing new technology. At the same time, as an electric energy saving measure, the electric power consumption in the sulfuric acid plant was vastly improved by decreasing the volume of gas treated the installation of low temperature activity catalyst in the 1st pass of the converter and optimization of main gas blower runner. Furthermore, last year, the oxygen plant was replaced and enlarged, and anode production increased from 240,000 to 280,000 tonnes per year with an associated increase of sulfuric acid from 550,000 to 660,000 tonnes per year. This paper describes these recent improvements in the acid plant at Naoshima smelter.

Jan 1, 2002

By Larry Twidwell, Ed Rosenberg, Courtney Young, Sean Dudley, William Gleason, Maureen Chorney

Experimental and industrially produced polystyrene and silica resins are tested for recovery capabilities of Rare Earth Elements (REE). Testing regimes being used are typical of resin analysis. Inductively Coupled Plasma-AES results indicate that preferential separation and recovery is possible in the adjusted pH range of2 to 10, solution conditions, and resin type. Testing conditions are resulting in structure modification of the composite resin as indicated by X-Ray Diffraction, Differential Scanning Calorimetry, Scanning Electron Microscopy, Mercury Porisometry, and density analysis. Resin modification indicates both surface and internal structure alteration outside of reported standard behavior of resins. Structural changes have ramification for both Rare Earth Recovery RER and traditional resin operations. Analysis shows that the resin uptake of REE can be manipulated for concentration. Further analysis with SEM work indicates that widespread surface and interior modification is taking place as resins load with REE. This modification is leading to pore rupture and particle breakage. Further investigation is being performed to determine the mode of breakage.

Jan 1, 2015

By Shilai Yuan, Huimin Lu, Zhijiang Gao, Panpan Wang

"Solvent refining of silicon through using Si-Al melts is a valid method to remove the impurities from metallurgical grade silicon (MG-Si) melt. The thermodynamic behavior of impurities Fe, Al, Ca, Ti, Cu, C, B and P in MG-Si during the solidification of MG-Si was studied based on the available thermodynamic parameters and experimental data. The morphology of inclusions was investigated by Scanning Electron Microscope (SEM). The chemical composition of inclusions in MG-Si and Al-Si melt was analyzed by EPMA. It is found that the amount of white inclusion reduces and most impurities are solved into the Al-Si melts. After solidification of Si–Al alloy using induction heating and acid leaching, impurities can be effectively removed. The solidification of silicon from the Si–Al melt is found to be more effective for purification than general silicon solidification.IntroductionPhotovoltaic energy is one of promising energy resources in a sustainable society because of its inexhaustibility and cleanliness. Although the production and installation of solar cells have increased significantly during the last decade, the cost of solar cell installation is still high. Multicrystalline silicon has now become the main material in the photovoltaic market because of its low production cost and because of the relative high conversion efficiency of solar cells made from this material, which has been studied for a long time [1-3].Electronic grade (EG) silicon (99.9999999% Si) is commonly used as the raw material to produce SOG-Si (99.9999% Si). Silicon produced from the chemical routes restricts the development of solar cells due to environment threaten, high energy consumption and low productivity. Purification of metallurgical grade silicon (MG-Si) is a low cost, environment friendly method. Although several metallurgical processes such as directional solidification, vacuum refining and electron beam melting [4], have been developed, the cost reduction and refining efficiencies for manufacturing silicon is still have to be further optimized.In the purification process, it is difficult to remove boron and phosphorus by the conventional metal refining method. The refining efficiency depends on the segregation behavior of different elements in solid silicon and the liquid phase. The segregation ratios of all investigated impurities were found to be much smaller than the segregation coefficients between solid and liquid Al-Si melts [5]. For instance, the segregation coefficient of B in Si is 0.8 at the silicon melting point (1687K), whereas it is around 0.2 when silicon is solidified from Si-Al melt at 1273K. For phosphorus the segregation coefficient is 0.06 when silicon is solidified from Si-Al melt at 973K°C, which is much less than 0.35 for recrystallization from liquid silicon. Since the segregation coefficient of boron in silicon is 0.8, it cannot be removed by directional solidification."

Jan 1, 2014

By Qian Li, Honggui Han, Jun Wang, Shichao Yu, Chunxiao Zhao, Maoxing Hong, Rui Liao, Xingxing Wang

In this study, bioleaching experiments, synchrotron X-ray Diffraction (SR-XRD), X-ray absorption near edge structure (XANES) and X-ray Photoelectron Spectroscopy (XPS) were conducted to investigate the intermediates and surface species of bornite leached by mesophilic mixed bacteria of Leptospirillum ferriphilum, Acidithiobacillus caldus and Sulfobacillus thermosulfidooxidans. CuS, Cu9Fe9S16 and S8 were the main intermediate species during bornite bioleaching by mesophilic mixed bacteria, and CuFeS2 was also detected. The surface species of S2− and S2 2− would be polymerized to Sn 2− during bioleaching. The formation of element sulfur and the increase of its content were confirmed by the fitted results of XPS spectra. The presence of polysulfide and element sulfur did not inhibit the bornite bioleaching. The formations of CuS and CuFeS2 were confirmed by the results of Cu K-edge XANES spectra.

Mar 1, 2018

By Srinath Viswanathan, Adrian Sabau

"In general, the occurrence of microporosity during metal casting is due to the combined effects of solidification shrinkage and gas precipitation. The governing equations for fluid flow and hydrogen evolution indicate that porosity formation and fluid flow are strongly coupled. However, in most studies on microporosity, it is considered that the porosity formation does not influence the fluid flow in the mushy zone. In this study, a computational methodology is presented for the numerical simulation of interdendritic fluid flow and microporosity evolution. The solution algorithm presented includes a fully coupled, implicit treatment of microporosity and local pressure in the mushy zone. The effects of microporosity evolution due to the local pressure drop in the mushy zone, and pore expansion in casting regions where liquid feeding alone cannot compensate for the solidification shrinkage are also considered. It is shown that neglecting the effect of porosity formation on the pressure in the mushy zone yields higher pressure drops. By its growth, microporosity partially compensates for the solidification shrinkage, reducing the feeding demand. A reduced feeding demand requires less fluid flow to compensate for solidification shrinkage, and results in smaller pressure drops in the mushy zone. Therefore, in order to accurately describe casting defects, comprehensive models of fluid flow, heat transfer, and solidification must include the effect of microporosity as well.IntroductionIn the terminology commonly used by foundrymen, porosity is usually considered to be either ""hydrogen"" or ""shrinkage"" porosity. Hydrogen porosity is the term given to porosity that is generally rounded, isolated, and well distributed. Porosity that is interconnected or clustered, and of an irregular shape corresponding to the shape of the interdendritic region, is usually termed shrinkage. In general, the occurrence of microporosity in aluminum alloys is due to the combined effects of solidification shrinkage and gas precipitation [1]. Continuum models [1, 2- 7] have been used to predict the level of porosity in castings. A number of other studies have also attempted to understand the phenomena of porosity formation and pore growth [8-10] and pore morphology [11].The governing equations for fluid flow and hydrogen evolution indicate that porosity formation and fluid flow are strongly coupled. However, in most studies [4, 9, 10], it is considered that the porosity formation does not influence the fluid flow in the mushy zone. Kubo and Pehlke [3] presented a methodology for the prediction of microporosity distribution in shaped castings by considering the effects of both the hydrogen precipitation during solidification and the pressure drop in the mushy zone. In their approach, the local pressure and porosity were computed in an uncoupled manner based on a ""flux of interdendritic liquid"" criterion, i.e., either pressure or porosity was first computed using the other variable at the previous time step. Their approach has been used with little change in numerous studies [6, 12, 13]. Recently, Kuznetsov and Vafai [14] presented a fully coupled, one-dimensional model for the computation of pressure and porosity. They showed that neglecting the effect of porosity formation on the pressure in the mushy zone yields higher pressure drops and an over-prediction of final porosity. They also showed that the influence of porosity formation on the pressure is larger at lower pressures in the mushy zone."

Jan 1, 2001

By Fumito Tanaka

The Converting Furnace (C-furnace) of the Mitsubishi process has solely provided opportunities for producing blister copper continuously from molten matte. Continuous converting originates from the proven technology for controlling the behavior of magnetite in lime-ferrite slag of the CaO-FeOX-Cu2O system. Recent improvements in the C-furnace operation have included the slag controls reflecting the impact of minor oxides on magnetite behavior. Although previous investigations focused on magnetite behavior, sulfur has also affected the C-furnace operation because it is of practical importance to avoid the precipitation of gypsum from lime-ferrite slag and the separation of matte from blister copper. This paper will quantify the behavior of sulfur in C-furnace with respect to the gypsum formation and matte separation, and discuss better controls for C-furnace operation.

Jan 1, 2006

By Johne Jesus Mol Peixoto, Ciro Azevedo Silva, Itavahn Alves da Silva, Weslei Viana Gabriel, Leticia Queiroz Ribeiro, Carlos Antonio da Silva, Varadarajan Seshadri

In this study,the influence of the immersion depth, casting speed on the flow characteristics in a beam blank mold with two tubular nozzles have been investigated using a physical model as well as CFD simulations.The results of CFD simulations were found to be consistent with the results of experiments in the physical model.The liquid jet spreads faster the flange region compared to the web region. This can lead to a non-uniform shell thickness along the cross section resulting in uneven solidification of the skin. The jet penetration depth ranged between 66 and 77 cm. The average intensity of meniscus fluctuation was 0.22 mm, and the maximum fluctuation was found to be 0.85 mm. Based on these results, the suggested optimum operating parameters for immersion depth and casting speed were 75 mm and maximum casting speed of 1 m/min.

Mar 1, 2017

By Yong J. Kim, J. M. Park

"Solid/melt interface shape during continuous casting process has a strong influence on the resulting microstructure of the ingot. The interface shape is primarily governed by the heat flow condition between the molten metal and mold (or container). The roll of the microstructural transition resulting from various solid/melt interface shapes is discussed using the Sn-22.6wt%Pb alloy. Three different types of mold such as cold mold, resistantly heated mold, and electromagnetically heated mold were used to generate those interfaces having different curvatures. Experimental measurements of complete temperature profile along the axis and surface of the ingot during downward continuous casting are presented to determine the solid/melt interface geometry. The results provide an explanation of the ingot property with emphasis on microstructure.IntroductionA large scale of continuous casting process of alloys often has a rather deep V channel type of solid/melt interface resulting from a limited heat flow condition. As a result, the deep V type solid/melt interface shape entraps defects such as pores and inclusions and also creates canter segregation. In order to reduce the defects concentration, electromagnetic stirring(EMS) mechanism has been applied to the melt in the channel[l]. Speith and Bungeroth introduced first experimental EMS device to the continuous caster in 1952.[2] Today, with wide ranges of benefit, a large variety of such technique is available. Electromagnetic field on the melt can be divided into three aspects. First, eddy current is induced on the metal surface by alternating magnetic field with high frequency, which results in heating the metal. Second, electromagnetic body force which is generated by the magnetic field and the eddy current reduces the melt pressure on mold or support the melt not to contact with the mold[3,4,5]. This force is used for electromagnetic casting process(EMC). Finally, it causes stirring in the melt. Many research efforts have been done on the EMC process to improve surface quality of slab[6] and control meniscus shape where three phases such as melt, solidified metal, and mold powder coexist[7,8]. However, the eddy current heating effect on the surface of the ingot was less considered. It is worth noting that induced eddy current on the surface of slab melts the solidified shell and thus changes the heat flow condition between the mold and melt. Mold heating effect was first proposed by A. Ohno[9] and its processing conditions were identified in details[ 10, 11]. The so-called Ohno process is based on the fact that by keeping the mold temperature slightly above the melting temperature of the liquid, no grain can be nucleated on the mold wall[12]."

Jan 1, 1998

By Takayoshi Fujii, Mitsumasa Hoshi, Chikashi Suenaga, Yoshiaki Suzuki

"In a bid to renovate its Saganoseki Smelter & Refinery and to establish a leading production unit in terms of global competitiveness, Nippon Mining & Metals undertook major - restructuring efforts since 1993.One of its themes was the shift from a two-flash furnaces operation to a single-flash furnace operation. The shift was successfully completed in 1996 while maintaining the production at the same level (330,000 metric tons per year of copper) by adopting such measures as improvements in pneumatic concentrate dryers, the concentrate feeding system, concentrate burners, the furnace cooling system, and a new cryogenic oxygen plant was constructed.With a view to realizing high matte grade operation (at 65%Cu) and increasing the concentrate feeding rate, further steps were taken the capacity of waste heat boiler was expanded and technical improvements were added, including optimization of the smelting reaction in the furnace shaft. As a result, the smelting capacity, as of the year 2000, has increased to 450,000 metric tons per year of copper.IntroductionThe feed rate to the flash furnace was doubled to 140 t/h from 70 t/h in 1996. Teething problems, as a result of the renovation, were almost solved by the end of 1996, and the operation of the single furnace operation has become stable.The main theme was the shift from a two-flash furnaces operation to a single-furnace operation to maintain the production capacity at the same level, namely 330,000 metric tons of copper per year. Then, in a bid to further renovate the Saganoseki Smelter & Refinery and to establish a leading production unit in terms of global competitiveness, further enhancement of the flash furnace's productivity was planned.The purpose of this plan was to raise the copper production capacity to 450,000 mtpy building on the potentialities of existing plants and without installing new equipment."

Jan 1, 2000

By Chao Li, Qian Li, Yong-bin Yang, Kai Li, Qiang Xie, Yuan-yuan Zhu, Dong-ye Li, Qi-bing Tan

"The permeability of sintering mix is a vital technological property in sintering process. However, it can only be measured by off-line method on samples picked from the production. In order to acquire the properties of sintering mix accurately, on-line measuring of permeability is urgently required. Based on the reflection characteristics of bed permeability on pipe flowing parameters, a new method is presented in this paper for on-line measuring of sintering mix permeability. The measurement can be performed by blowing gas flow in the bed with the measuring pipe. Measuring results are obtained by picking the data on flowing rate and pressure in the pipe. The function of flowing rate to pressure may be certain for samples with the same permeability. Thus, the permeability was determined by contrasting this function to the result of off-line measuring, and the relative coefficient or R2 value was more than 99%.IntroductionThe permeability of sintering mix is a vital technological property in sintering process, which directly determines production and quality of sinter, or even determines whether the sinter production is carried out smoothly [1,3].The permeability have more obvious influence on vertical sintering speed, which is mainly related to air quantity passing through material bed. Under certain inducing capacity and negative pressure, the vertical sintering speed mainly depends on the permeability of sintering mix. Low permeability may make burning through point of sintering move back, and the sinter mix cannot be burnt through. High permeability may make burning through point of sintering move forward, improving production efficiency by increasing the speed of sintering machine [4] Good permeability means a small resistance of fan ,reduction of negative pressure of sintering machine, and full contact between air and sulfide, which can strengthen physical-chemical reaction during sintering process and increase desulphurization rate. In gas well through material layer process, gas-solid desulfurization reaction and gas-solid-liquid heat exchange are completed and hot gas through the combustion zone supplies the sintering process with heat. Finally uniform sintering of the material layer in height and width direction is achieved [5] While high permeability index leads to weak sinter strength, fast sintering speed, short residence time of high temperature region and little liquid phase. Moreover, liquid phase in the fast cooling process is too late to fully crystallize but forming glass phase which is harmful to sinter strength as well. Bad permeability means a big fan resistance and increase of negative pressure of sintering machine, which make the air pass through material layer difficultly. When air and mix contact difficultly, removal of sulfide reduces so that desulfurization is incomplete. Meanwhile, low caking efficiency, slow sintering speed and easily burnt sinter , reduce sinter output. Therefore appropriate permeability of sintering mix is the premise of stable burning through point and satisfactory sinter output and quality."

Jan 1, 2013