Search Documents

By Dong Hoon Han

The sulfation rates of magnesium oxide and calcium oxide (molar ratio 7:3) contained in calcined CMA ( calcium magnesium acetate) by SO2 were measured. The experiments were carried out in the temperature range 700 to 1100 °C and under the SO2 concentrations of 0.3 to I mol % (5 % 02). In the low-temperature range below 830 °C the reaction produced CaSO4.3MgSO4 and unreacted MgO, but no MgSO4 phase. The formation of CaSO4.3MgSO4 phase has a significant implication in that it allows the utilization of MgO for SO2 removal whereas the sulfation of MgO from conventional sources is so slow that it is of no practical interest. Thus, the calcined CMA can remove SO2 at lower temperatures than conventional SO2 absorbents and at a greater capacity. Above 950 °C only CaO reacts with SO2, but at a much greater rate than the calcined Ca(OH)2, which is one of the most reactive SO2 absorbents.

Jan 1, 1998

By Sang-Beom Lee

For thermodynamic prediction, the deoxidation equilibrium of aluminum in Fe-36%Ni alloy was studied with a cold crucible under Ar gas atmosphere at 1773K. For the deoxidation reaction in liquid Fe-36%Ni base, i.e.: A12O3(s) = 2A1 + 3O The interaction parameters and the equilibrium constant between aluminum and oxygen in liquid Fe-36%Ni alloy are given in the following: eo Al = -3.8, roA1=0.9, eAl° = -6.4, rAl° = 700, rAIAIo = 3.1, roA1o = 833 within the composition range of [Al] < 1 mass%. The temperature dependence of the equilibrium constant was obtained in the range of 1773K < T < 1973K by using reported data and present results as follows: log KAo= 0.58-24463.7 / T The deoxidation equilibrium with aluminum in Fe-36%Ni could be thermodynamically well described in the range up [Al] < 1 mass% with first and second order interaction parameters as well as the equilibrium constant determined in this study.

Jan 1, 2002

By Józef Czernecki

Chalcocite-bornite concentrates of KGHM contain, similarly to chalcopyrite concentrates, 20-30 wt.% Cu but several times less iron (2-7 wt.%) and sulphur (9-12 wt.%). Another useful characteristic of KGHM concentrates is the presence of organic carbon (5.5-8.5 wt.%) in them, which serves as fuel in the flash smelting process. The main contaminants of the concentrates are lead (1.3-2.5 wt.%) and arsenic (0.05-0.4 wt.%) which require appropriate technological treatment in order to remove them from the copper pro-duct. Chalcocite-bornite concentrates are processed in KGHM by two different processes: ? a flash smelting process (Glogow 2 Smelter) ? a shaft smelting process (Glogow 1 Smelter, Legnica Smelter) The shaft smelting process used in the Glogow 1 Smelter and in the Legnica Smelter has higher production costs than the flash smelting process of HM Glogow 2. Additionally, the shaft smelting process employs several concurrently running installations (six dryers, seven briquetting lines, six shaft furnaces, nine converters), the operation of which, including maintenance, requires significant financial expenditure. Therefore, the Company is currently considering the substitution of the shaft furnace process in the Glogow 1 Smelter and in the Legnica Smelter by the one stage flash smelting process located in the Glogow Smelter, with output equaling the copper production capacity of both smelters, i.e. 320 000 ? 350 000 t/a. There are two technological options being considered which differ from each other in their man-ner of flash slag cleaning. In the first, the slag cleaning would be the same as in the existing Glogow 2 Smelter, i.e. the slag would be cleaned by pyrometallurgical reduction of the oxide copper and other metal compounds in the electric furnace in order to produce waste slag containing below 0.6 wt.% Cu. However, the other option of the flash slag cleaning would be carried out in two stages. After preliminary slag reduction in the electric furnace to 3-5 wt.% Cu, there would be flotation of the partially reduced slag.

Jan 1, 2006

By Shoukun Wei, Cong Wang, Lin Cheng, Zhiyu Qiao, Jingkui Liang, Weidong Zhuang

"The subsolidus phase relations in the Sm2O3-CeO2-CuO ternary system sintered at 1000°C in air have been investigated by X-ray powder diffraction. The system can be divided into two ternary phase regions and three binary phase regions. Solid solution Sm2-xCexCuO4-y is the only ternary phase in the system. The maximum solid solubility was confirmed to be x = 0.2. The crystal structure, oxygen content and superconductivity of the solid solution Sm2-xCexCuO4-y have been investigated.I. INTRODUCTIONAfter the first discovery of the superconducting ceramic system La-Ba -Cu-O[l] with Tc = 30 to 40K, other families of cuprate-based ceramics have been synthesized with higher critical temperature. These oxides include the R-Ba-Cu-O (R: rare earth) systems (Tc=90K or so)[2,3], the Pb-Sr-(R,Ca)-Cu-O systems (T c = 50 to 100K), the Bi-Sr-Ca-Cu-O systems (Tc=80 to 105K)[4], the T1-Ba-Ca-Cu-O systems (Tc=85 to 125K)[5], the Hg-Ba-Ca-Cu-O systems (Tc=90 to 150K)[6,7], and some others. The improvement of Tc is very rapid. The measurement of the Hall and Seebeck coefficients shows that they all are p-type superconductors. In 1989, Tokura et al.[8] discovered the superconductors R2_XCexCU04_y(R = Nd, Pr, Sm) with Tc=20 to 24K (onset) and found that the charge carrier is electron in contrast to their hole doped counterparts. This discovery increases the fundamental understanding of the cuprate-based superconductors by comparing their characteristics and mechanisms to those of the p-type superconductors.One of the outstanding features of these n-type superconductors is the difficulty in obtaining samples in good charactors, such as the difficulty in obtaining zero resistivity state in single crystal or bulk samples; the semi-conductivity of bulk samples in ordinary state (opposite to the superconducting state) and a reducing reaction involved before the superconductivity has been found[9]. Therefore, it is necessary to optimize the sample preparation of the n-type superconductors. All the n-type superconductors have been found· considerable solid solubility. The compositional variations play a governing role in the carrier doping of the superconducting phases. Also, it is vital to the ceramic processing of superconductors to identify the compatible phases in the phase diagram. Finally, there is always the possibility of finding additional compounds, both superconducting and non-superconducting, in an unexplored system."

Jan 1, 1996

By M. Pakala, Z. Fan, Ray Y. Lin

Deposition of hard chromium coatings using electrodeposition is accompanied by emission of hexavalent chromium mists which is a carcinogenic. Hence alternative chromium deposition technologies are being investigated. Sputter deposition is a strong candidate to economically deposit hard chromium coatings in an environmentally friendly way. Chromium coatings of 2-3 µ m thickness were deposited on plain carbon steel coupons using RF magnetron sputter deposition. Depositions were carried out with 0 to 22 vol% nitrogen in the plasma. Structure of the coatings was studied using x-ray diffraction analysis With increasing nitrogen contents, formation of the two nitride phases was observed. The pure chromium phase was detected in coatings with up to 7% nitrogen in the sputtering gas. The solid solution of nitrogen in the pure Cr phase coating was identified by shifts of Cr x-ray diffraction peaks to higher d-spacing. The microhardness of the coatings deposited at a substrate temperature of 200°C showed an increase in hardness with increasing nitrogen content from 600 kgf/mm2 (5.9 GPa) at 0% nitrogen to I250 kgf/mm2 (I2.25 GPa) at 9.5 % nitrogen and a subsequent decrease in hardness to I 100 kgf/mm2 (11 GPa) beyond 9.5 % nitrogen in the sputtering gas. This corresponds to the formation of the hard Cr2N phase, at 9.5 % nitrogen, and CrN phase, at I5.7 % nitrogen. The reported bulk hardness values of Cr2N and CrN are I600 kgf/mm2 (I5.7 GPa) and I 100 kgf/mm2 (11 GPa) respectively. For pure Cr phase coatings, there is a slight increase in hardness for coatings deposited at 7. I % nitrogen from that without nitrogen in the sputtering gas. This could possibly result from the solid solution strengthening of the Cr lattice by nitrogen. For films deposited at 200°C, phases of the deposited films seem to be the overwhelming factor in controlling the microhardness.

Jan 1, 1998

By Suleyman Tekeli, Serdar Salman, Bulent Aktas

"The effect of La2O3 content up to 15 wt% on phase stability, sintering and microstructure of cubic zirconia (8YSZ) was investigated. XRD results showed that the specimens containing up to 15 wt% La2O3 were composed of only cubic structure. Also, the specimens doped up to 5 wt% La2O3 revealed no La2O3 peaks, indicating that La2O3 was completely solubilized in the cubic structure. However, when> 5 wt% La2O3 was added, the peak of La2Zr2O7 compound emerged, showing that the overdoped La2O3 was not solubilized in the 8YSZ matrix. The lattice parameter of the 8YSZ slightly decreased with the increasing La2O3 content up to 1 wt% but further increase in the La203 amount resulted in an increased lattice parameter. The comparison of grain size of the 8YSZ specimens with various La2O3 content showed that grain size slightly increased with the increasing La2O3 content up to 1 wt% but further increase in the La2O3 amount resulted in a decreased grain size.IntroductionAt atmospheric pressures, three polymorphic forms of Zr02 are stable at different temperatures i.e. monoclinic, tetragonal and cubic. A high-pressure orthorhombic form of Zr02 has also been reported[l]. The successful production of pure Zr02 bodies is not possible all the time due to the large volume expansion associated with the martensitic tetragonal-monoclinic transformation. This fact restricts the applications of zirconia, in spite of its excellent mechanical and thermal properties. However, the stabilization of the high temperature polymorphs at room temperature as stable phases is made possible by addition of suitable dopants. Fully stabilized cubic Zr02 and partially stabilized tetragonal Zr02 show interesting properties and are widely used as ionic conductors, coatings and gas sensors in solid oxide fuel cells and structural applications[2]. Most frequently used dopants include Y203, CaO, MgO and Ce02, although other oxides, such as those of rare earth elements, can also act as stabilizers of the high temperature structures. The incorporation of aliovalent cations to the lattice, forming substitutional solid solutions, allows to control the concentration of anionic vacancies in the structure. This aspect is particularly important in designing ionic conductors[3], and is also determinant in the stabilization process[ 4]. The process of stabilization with larger ionic radii dopants is rationalized by the crystal chemistry model[ 5], that describes the dopant cations as typical stabilizer when they have larger ionic size, lower charged state and higher ionicity than Zr4+ The ionic radius of Zr4+ is 0.84 Å and that for La3+ is 1.016 Å [6]."

Jan 1, 2012

By Juárez T. Julio Cesar, Mendez R. Eliecer, Reyes P. Martín, Flores G. Mizraim Uriel, Teja R. Aislinn Michelle, Hernández C. Leticia, Reyes D. Iván Alejandro

The present study shows the characterization of a zinc concentrate collected at Hidalgo, Mexico, in order to identify its mineralogical species and to propose a leaching methodology for silver recovery. The results obtained by X-Ray Diffraction (XRD) show Sphalerite (ZnS) as the mineralogical matrix and silver into the specie proustite (Ag3AsS3). The techniques of Scanning Electron Microscopy-Energy Dispersive Microanalysis (SEM-EDS) and Polarized Optical Microscopy (POM) identified the presence of sulfides of Fe, Cu, Pb and Zn, in addition to silicates and feldspar. The proposed dissolution method of Ag(I) was carried out with [S2O3 2−] = 0.5 M and [NaOH] = 0.1 M to regulate the medium at pH = 9 for 12 h at 298 K. Oxidation of the concentrate was favored by injection of O2 to a partial pressure of 1 atm. Monitoring of the reaction was carried out by reading the [Ag] and [As] by AAS.

Mar 1, 2017

By Chuanfu Zhang, Liwei Liang, Yanxin Wu, Jinliang Wang

"According to the reaction shaft operation characteristics during the flash smelting process, 15 groups of slag samples containing high Fe3O4 were prepared by some chemical reagents, and then the slag viscosities were measured using a RTW-10 type synthetic test instrument for melt physical property by the rotating cylinder method. The effects of Fe/SiO2 ratio (mFe/mSiO2), Fe3O4 content (wFe3O4), Cu2o), MgO content (WMgO) and Cao content (wCaO) on the slag viscosity were also studied. Results show that slag viscosity is decreased with the increase of temperature, mFe/mSiO2, wCu2o, wMgO and wCao, and with the decrease of wFe3O4, under the range of slag contents: mFe/mSiO2 1.36~1.78, wFe3O4 17.83%~21.18%, wCu2o 3.51%~8.34%m wNgI 2.21%~6.57%m w/caI 6.22%~9.387% and temperature range if 1250 o/c~1450 oC. Only wFe3O4m and w/caO have great influence on the slag viscosity when temperatures as high as 1400 oC. Only wFe3O4 and wCaO have great influence on the slag viscosity when temperatures as high as 1400 oC or so. To form a freeze slag with higher viscosity inside the reaction shaft, wFe3O4 should be more than 20% and wCaO should be less then 6%.IntroductionSince its appearance in 1949, Outokumpu flash smelting technology has making continuous innovation and has become the most competitive intensified smelting technology [1], widely considered to be the standard clean smelting process [2]. At present, flash smelting technology is adopted to newly build or reconstruct most of the world's copper or nickel smelting enterprise [3]. Reaction shaft is the most important part of the flash smelting furnace. During the flash smelting process, reaction shaft must be able to withstand the following harsh conditions at the same time: 1) high temperature varying from 1400 °C to 1500 °C. 2) strong oxidative atmosphere containing 50% - 80% oxygen. 3) solid particles and melt with speed up to l00 m/s. 4) high acidic or basic slag with strong chemical corrosiveness. 5) smelting gas containing 50% - 80% SO2. 6) matte with strong dissolution."

Jan 1, 2012

By Patricio Barrios

The Rio Tinto Metal (RTMetal) copper smelter, located 5 Km from Huelva, Spain, began operations in 1970. Since then a series of expansions and modifications have allowed a progressive increase in copper production. Environmental considerations having become increasingly important, environmental protection has come to represent an important aspect of the investments in production. As a result, modifications have been carried out in the two existing acid plants: -Modification of the RTM I gas cleaning section to closed circuit. -Substitution of cascade filters and acid lines. -Modification of the RTM I plant to double absorption. The Expansion and Environmental Improvement Project, completed end 1995, will allow 270,000 t Cu and 800,000 t H2SO4 to be produced yearly, at the same time achieving a decrease in specific and overall emissions. RTMetal&apos;s goal is to be an efficient smelter, with the avowed intention of respecting the environment and adopting the best available technologies.

Jan 1, 1996

By R. G. Henley

Mount Isa copper concentrate was combusted in a laminar-flow furnace. The conditions simulated those likely to be encountered in flames in flash smelters of the Outokumpu (air as oxidant) and INCO (oxygen as oxidant) types. The range of conditions studied was as follows: T 400-1400°C, 02 0-100%, SO2 0-95% for residence times up to 0.23 s. The distribution of sulfur, arsenic and lead between the particles and the gas phase was studied. Combustion was very rapid provided the concentrate was adequately dispersed, i.e., no agglomerates. The importance of the latter is discussed. It was possible to oxidize 80% of the sulfur present in the con¬centrate after only 0.1 s reaction time at 1000°C in an atmosphere contain¬ing 8.5% 02 and 12.5% SO2. Best volatilizations (90% of the As, 52% of the Pb) were obtained under localized conditions attained in an air-type flame. Average volatilizations were: air-type flame, As 50%, Pb 32%; oxygen-type flame, As 40%, Pb 30%. The substitution of oxygen for air reduced the arsenic volatilization. The products of combustion were mainly cuprospinel and cuprite; small inclusions of elemental copper were found in some of the particles. At high temperatures, there was a loss of copper due to vaporization of CU( g) CuO kg) (g)

Jan 1, 1983

By N. Ono, H. Fujiwara, S. Otsuka-Yao-Matsuo, T. Omata

"The electrical conductivity and the oxygen release and uptake of sintered indium tin oxide (ITO) upon heating and cooling under the condition that P(O2)/P*=4.9X10-4 (P* = atmospheric pressure), :when P(O2) was approximately 50Pa, were simultaneously measured by using a closed-system oxygen-gas analyzer. A large increasing in -the electrical conductivity - upon the· oxygen release detected in 1130<T<1273K was observed. Quantitative relationship between the number of oxygen atom released from ITO and the conduction electron density in ITO was studied. The release of one oxygen atom agreed with the generation of two conduction electrons, i.e., the efficiency-carrier-generation for the oxygen release from the ITO was almost one. The oxygen atom released must be originally at the quasi-anion site in the C-type rare-earth lattice, i.e., the 16c site in the space group of Ia3, as an interstitial excess oxygen, Oi"". It was concluded that the mechanism of conduction carrier generation and compensation upon SnO2 doping into In2O3 can be expressed by the defect equation, 2SnO2-2Sn1n +2(1-z)e'+zOi""+3O0 x+(l-z)/2O2, and that the oxygen release bringing the increase in the electrical · conductivity can be expressed by the equation, Oi""-1/2O2+2e'.IntroductionThin films of SnO2-doped In2O 3 (generally designated as ITO, for indium tin oxide), which have high optical transparency for visible light and high electrical conductivity, have been used as transparent electrodes for liquid crystal and electrochromic displays. It is well known that the electrical conductivity of ITO depends on the content of SnOi-dopant and oxygen. However, a reliable relationship between electrical conductivity and the absolute oxygen content in ITO has yet to be reported. The elucidation of such a relationship is one of the important clues for realizing extremely highly conductive ITO electrodes."

Jan 1, 2000

Segregation roasting tests were carried out on Zaire cobalt oxide ores assaying about 2% Co and 3.5 to 6.5% Cu. The major parameters tested during the laboratory investigations were temperature, dosage and type of reducing agent, dosage and type of chloridizing agent, and particle size. Results showed that standard conditions suited to the segregation of copper ores, i.e. low temperature and low dosages of reducing and chloridizing agents, resulted in the segregation of copper only, while conditions suited to the segregation of lateritic nickel, i.e. higher temperature and increased dosages of reducing and chloridizing agents, led to a successful segregation of both copper and cobalt. Under the best conditions, 88% of the cobalt and 98% of the copper could be recovered in a concentrate assaying 32.5% Cu and 8.5% Co. Alternatives to process such a concentrate are briefly reviewed.

Jan 1, 1993

By Dinabandhu Ghosh

The stability diagram of the ternary system Ti-C-O is drawn in the present work for four temperatures, 1473 K, 1573 K, 1673 K and 1873 K, showing the stability fields of TiC, Ti, TiO, Ti2O3 and TiO2. An analysis of the system reveals that it is not possible to produce Ti in a carbon-saturated system; instead, the stable product is TiC. However, Ti can be an equilibrium product in a carbon-unsaturated system at prohibitively low values of pCO and pCO2; for example, at 1873 K, these limiting values are: pCO = 10-6.76 atm and pCO2 = 10-13.36 atm, which, when exceeded, produce TiC and TiO respectively. The magnesiothermic reduction is examined through the stability diagram (log pO2 vs. 1/T) of the system Ti-Mg-O, drawn for a number of pMg values, presenting the pairwise stability fields such as Mg(l) + Ti(s), Mg(v) + Ti(s), MgO(s) + Ti(s), etc. The diagram shows that magnesium reduction of TiO to Ti is possible only at T < 1641 K with pMg = 1 atm and only at T < 1569 K with pMg = 0.5 atm. An experimental scheme for Mg vapor reduction of TiO2 is proposed in which an argon stream is passed over a Mg(liquid) evaporator at temperature T1 (say, 1234 K); the resulting Ar-Mg mixture at 1 atm is subsequently flown over a bed of TiO2 at temperature T2. A thermodynamic analysis establishes that complete reduction to Ti is possible and that the best results are obtained when T1 = T2.

Jan 1, 2006

By Hidekazu Nakagawa

We investigated the anodic dissolution behavior of titanium in TMHA-Tf2N molten salt, which has a wide electrochemical window of about 5 V, in order to develop an electrodeposition method for titanium. By etching a titanium electrode in HF?HNO3?H3PO4 solution, the titanium electrode became electrochemically active, and a redox reaction was observed at around -0.15 V vs. I-/I3- in (TMHA-Tf2N)?HTf2N solution. We identified the redox reaction consists of the reduction of the proton and the oxidation of hydrogen. The diffusion coefficient of the proton in TMHA-Tf2N was calculated to be 6.9 10-8 cm2 s-1 at 50 °C from the cathodic peak current in the cyclic voltammogram. Anodic decomposition of the molten salt was not observed up to 6.0 V vs. I-/I3- on titanium electrode, while it was observed at around 2.0 V vs. I-/I3- on platinum and glassy carbon electrodes. Cathodic decomposition of the molten salt was observed at around -3.0 V on the titanium electrode, as well as on the platinum and glassy carbon electrode.

Jan 1, 2006

By T. Iriyama, Y. Fujita, R. Omatsuzawa, T. Nishio, N. Okochi

Sm-Fe-N hard magnetic materials are good candidates for high performance bonded magnets. Rapid-quenching method should be highly favorable for the fabrication of isotropic magnet powder with high coercivity. We report here the magnetic properties of Sm-Fe-N powders produced by a few kinds of rapid-quenching processes. Sm2Fe17 powders were prepared by gas-atomization (GA), rotating-disk atomization (RDA), or melt-spinning (MS) method. The Sm2Fe17 GA powder had dendritic solidification structure, while the RDA powder had micro crystalline structure with size of 3-5 µm. Coercivities (HcI) of their nitrides were 56 (for GA) and 217 ka/m (for RDA). The H cI of nitrided Sm2Fe17 MS powder with wheel velocity (V5) of 5-20 m/s, which had also microcrystalline structure, was 53 to 509 Wm. These coercivity values are not sufficient for bonded magnet applications. From the study of additive effects, it was found that C, C-Si, C-Ga, or C-Al addition decreased the crystal size of quenched Sm2Fe17 powder. Consequently, high coercivity was obtained; the HcI of nitrided Sm2Fe1C1Si1 MS powder with V5 of 10 m/s was 898 kA/m, and 708 kA/m for the nitrided Sm2Fe15C1Si1 RDA powder. The compression-molded bonded magnet made from Sm2Fe18Si0.1Nx MS powder showed a high (BH)max of 82.7 kJ/m3.

Jan 1, 2000

By Jay Black

In the thiosulfate gold leaching process gold is oxidized to Au+ by a copper(II) ammine catalyst and complexed by thiosulfate. Copper(I) complexes, formed during gold oxidation, are reoxidised to Cu(II) complexes by oxygen. In this study, we present the results of a spectrophotometric study of the Cu(I)-NH3-Cl system, which follows on from our recent investigations of speciation in the Cu(I)-Cl and Cu(I)-S2O3-Cl systems and is part of a detailed study of copper(I) speciation associated with the gold leaching process. Formation constants for Cu(I)-NH3-Cl complexes have been determined by modeling the systematic changes in the UV spectra that occur as the concentration of the components is varied. The analysis of the data indicates that three Cu(I)-ammonia complexes are present, i.e., [Cu(NH3)2]+, [Cu(NH3)Cl2]- and [Cu(NH3)2Cl] and their respective log Kf values are 11.13, 8.33 and 10.79 at 25°C. Investigations of the oxidation of Cu(I)-NH3-Cl solutions by oxygen in the atmosphere are also presented. These experiments indicate that the reaction of copper(I) complexes progresses through various intermediates. The presence of many copper(I) and copper(II) complexes in ammonia thiosulfate solutions complicates the task of determining optimal conditions for gold leaching. Further studies are needed to identify the complexes and chemical processes that are important in the Cu(I)-NH3-S2O3-Cl system.

Jan 1, 2003

By In-Hyeok Choi

Currently, spent V2O5–WO3/TiO2 catalysts contribute significant amounts of solid waste following increasing levels of global demand. V2O5–WO3/ TiO2 catalysts usually consist of TiO2 anatase as a supporting oxide, vanadium as a catalytic agent, and other promoters such as tungsten, silicon, and calcium. Although vanadium is the main catalytic agent, a relatively high content of tungsten (WO3, 7–10 wt%) typically exists compared to vanadium (0.5–1.5 wt%). Considering the irreplaceable properties and industrial importance of tungsten, a feasible method for the recycling of spent V2O5–WO3/TiO2 catalyst should be established to utilize it as a secondary source. This paper presents a process to recover tungsten from spent V2O5–WO3/TiO2 catalyst. The processes proposed here involving roasting, decomposition using HCl, ammonia leaching, and crystallization. Within the process, ammonium paratungstate (71 wt% as WO3) is obtained as a final product. The total yield rate of tungsten from feedstock was found to be 96.3%.

By De-qing Geng, Guang-liang Wu

The waste slag generated by the LF refining process of Q345B low alloy hot-rolled steel, still has some refining capabilities. If recycled, it can reduce environmental pollution, and save the economic costs. A research on melting Characteristics of Q345B steel LF refining waste slag was investigated by using orthogonal experimental method, and the effect laws of composition on that were analyzed. Through variance analysis and significance criterion, it is concluded that the optimum ingredient of the regenerated LF refining slag is 25%A12O3, 12%CaF2, 7%MgO and R= (CaO)/ (SiO2) =2.5. And the regression analysis is carried out by using SPSS software, to get the mathematical relationship between ingredient with high reliability and melting temperature of refining slag T=1451.3-6.25CaF2+2.36 R.

Jan 1, 2016

By Z. Zak Fang, P. Fan, S. Middlemas

"Titanium dioxide (T1O2) has been widely used as pigment in paints, paper and cosmetic products, as well as high-tech applications such as PV Cells, semiconductors, biomedical devices and air purification. T1O2 pigment is primarily produced by the high temperature chloride process, resulting in considerable CO2 emissions. A novel hydrometallurgical process for making T1O2 pigment without direct CO2 emission is investigated. The new method promises to eliminate direct CO2 emissions, consume significantly less energy, and produce minimal environmental waste. The novel process involves molten salt roasting of titania slag, with subsequent washing, leaching, solution purification, hydrolysis, calcination and post-treatment stages, resulting in high-purity anatase or rutile pigments while realizing significantly reduced environmental impacts. Pigment whiteness is critically sensitive to trace amounts of discoloring impurities such as iron and chromium. Several methods for reducing the levels of these impurities are investigated. Energy consumption and emission models are also developed.IntroductionTitanium dioxide (T1O2) is one of the most commonly used minerals in the chemical manufacturing industry. It has been commercially processed since the early 1900's, and has a wide variety of applications. Pigment is used in paints [1], plastics and paper [2], sunscreen [3], cosmetics and even as a food additive [4]. T1O2 has also been used in photovoltaic cells [5], biomedical devices [6], and in air purification [7]. T1O2 pigment has a refractive index of 2.7, which imparts a high level of opacity (and hence whiteness) to whatever material it is added [8]."

Jan 1, 2012

By Jyri Talja, Shaolong Chen, Hannu Mansikkaviita

"Drying (water removal) prior to smelting is always economically feasible. Unnecessary heating of vapour can thus be eliminated resulting in savings of5-15 MUSD every year.Thermodynamically removal of one ton of water out of copper concentrate at 100 °C (with 10 % moisture) requires approximately 3150 MJ/tH2o, consisting of heating of the water (377 MJ), heating of the concentrate (509 MJ) and water evaporation (2260 MJ). This is quite independent of the selected drying technology. In reality some more heat is needed as higher temperature is practiced to enhance the drying performance and to reduce the equipment size.Major nominator in drying energy efficiency is amount of gases, which depends greatly on the drying technology. Dryers based on direct heating with fossil fuels have high gas flow rates, and thus they require additional energy of about 1400-1600 MJ/tH2o, compared to indirect modemsteam drying at 250-400 MJ/tH2o.Significant benefits in energy consumption (900-1300 MJ/tH2o) with additional potential for a bonus profit of 2-4 MUSD/y year, together with full elimination of some 40 000 tpy CO2 per mid-size dryer is available by selecting sustainable, energy efficient steam drying.IntroductionRemoval of water from the concentrate is very energy intensive thus having a significant environmental impact. However, drying prior to smelting is always economically feasible and very often viable also from the perspective of process operations. This environmental impact of drying can, however, be decreased or even fully eliminated with proper selection of the drying technology.Energy incorporated in drying consists always of a number of phases like liquid (water), solids (concentrate) and gases (water vapour, purging I dilution air, combustion gases). Each phase is heated to a specific temperature during the drying process.Heating of water, heating of the concentrate and water evaporation consumes more or less the same amount of energy despite of the drying technology (3150 MJ per ton of water). In conventional drying this amount of energy is achieved by combustion of fossil fuels wirg subsequent CO2 emission. Alternatively, chemical energy derived from sulphide smelting can be utilized in a form of steam thus generating zero emission ofCO2, in modem steam drying."

Jan 1, 2012