Search Documents

By Vladimir Lobanov, Vladimir Skorohodov, Boris Radionov, Olga Makovskaya

"The synthetic sorbents and the activated carbons which are used for the metals extraction from weak process liquors are rather expensive. It is propose to use mineral and synthetic high-porous substances which sharply increased sorption properties by special processing. For achievement the desirable properties sorbents are impregnated by specially prepared solutions. Such solutions should contain the substances or its anionic forms which on the one hand are strong enough fixed in a supporter pores, with another are capable to form the insoluble compounds with extracting metals. Selectivity is provided by chemism of the reagent interactions with extracting metal. Due to the high concentration of a reacting ion in a sorbent phase the capacity and rate of sorption increases. Formed insoluble compound remains in a phase of the sorbent and necessity of its filtration disappears. For synthesis the sulfhydryl compounds which chemical properties allow to increase degree of extraction and capacity of the activated carbon were used. At hydrometallurgical processing of precious metals mineral raw materials the commercial solutions with the concentration of gold from 0,1 to 5 mg/dm3 are received. Commonly gold is precipitated from cyanic solutions by the zinc dust. The sorption methods are widely applicable. But the synthetic sorbents and the activated carbon using to these purposes are rather expensive. Expenses for sorbents even at its regeneration can reach 10-15 % from total expenses of gold extraction from ores. When sorbent regeneration, mostly for carbon, is not provided, this share increases to 30-40 %. Thereupon search of the sorbents combining availability, the sufficient capacity, demanded degree of extraction and the low price is actual. For the specified purpose it is offered to use the mineral and synthetic high-porous materials which sorption properties are sharply rose by special treatment. Among such substances are natural zeolites, silica gel, lignine et al. Similar treatment can improve the sorption properties of sorbents used in practice, particularly, the activated carbons. The simplest treatment of potential sorbents consists in its impregnation by specially prepared solutions. Such solutions should contain substances or its anionic forms - impregnating agents. These agents should be on the one hand strong enough fixed in a carrier pores, on the other hand are capable to form with extracting metals insoluble compounds. The more strong compounds are formed the high degree of metals extraction from solutions. The sorbents with similarly changed properties are named the impregnated sorbents."

Jan 1, 2008

By Jincheng Hu, Honggang Zhong, Qijie Zhai, Congsen Wu, Cheng Zhang, Jingzheng Ye

"The influence of cooling intensity on the solidification structure and ferrite phase content of a new duplex stainless steel (DSS) was investigated by using a thermal simulation setup for continuous casting. The results showed that the characteristics of the solidification structure were similar to their industrial scale manufactured slabs, including chill zone, colunmar zone and equiaxed zone. And austenite morphologies were mainly primary and secondary Widmanstatten sideplates as well as intragranular Widmanstatten plates. In addition, it revealed that the ferrite content increased with an increasing distance from the chill surface and decreased at colunmar to equiaxed transition (CET) position, then the value remained relatively stable at equiaxed zone. Furthermore, the ferrite content presented the same trend with the cooling intensity ranging from 100 mL/min to 2000 mL/min with the values just varying in a slight range.IntroductionThe duplex stainless steel (DSS) is the kind of steel that ferrite phase and austenite phase occupy about 50% respectively, or the content of the fewer phase has to be more than 30% [l]. The success of modem duplex stainless steels is to a large degree due to their higher strength than austenitic stainless steels, higher toughness than ferritic stainless steels, good weldability and high resistance to stress corrosion cracking as well [2,3]. The cost of stainless steel production continues to soar in recent years due to the increasingly higher price of Cr. In order to decrease the production cost, a new type of duplex stainless steel was developed by Bao steel [4]. This newly developed duplex stainless steel had low Cr content compared with 2205 DSS, and was expected to be applied into automobile industry. However, this type of steel was still in the initial stage of development, and the influence of continuous casting process on its solidification process and structure was still unclear, which needed to be studied further. Several works published in literature presented the effect of continuous casting conditions on duplex stainless steel (DSS) 2205, 2304 [5,6]. It was discussed that the cooling intensity in the chill-side had little efficient influence on the phase transformation. In this paper, the effect of cooling intensity on the solidification structure and ferrite volume fraction of this DSS at a given cooling rate was investigated."

Jan 1, 2014

By Wenxian Zhu, Patrick R. Taylor

"The small dimensions of nano-sized materials leads to novel and enhanced mechanical and physical properties. A thermal plasma reactor has been developed to study the formation of nanometer sized metal powders. A supersonic nozzle and a powder filter were designed and built. By vaporizing coarse metal powders in the plasma flame, and quenching the metal vapors through the nozzle at the rate of 107 K/sec, nanometric sized powders have been produced. The powders were collected in an airtight secondary quench-filter system. The particle size of the product power is 5 -20 nanometers, obtained through TEM analysis. The XRD analysis showed that the powder did not oxidize after the filter was handled in an inert atmosphere glove box.IntroductionNanostructured materials have been shown to exhibit improved physical and mechanical properties compared to conventional materials with larger grain sizes (1,2). There have been several methods proposed for preparing nanometer size materials. Thermally induced vapor-phase reactions have been used to produce a variety of powders. A common feature of these processes is the rapid production and cooling of condensable reaction intermediates and products, by gas-phase reactions, leading to the formation of a large number of very small particles. Thermal plasma synthesis of ultra-fine size particles has been attracting increasing interest (3,4,9-11), because it offers many advantages, especially in refractory materials processing, compared to conventional processes: (a) thermal plasma temperatures are very high(> 5000 K); (b) the rates of chemical reaction are much faster than those encountered in conventional processes; (c) high-purity materials may be obtained using fewer processing steps by collecting the product at temperatures where the by-products are in the vapor phase; ( d) the mean particle diameter can be controlled; (e) unifom sized particles may be produced with clean surfaces (these particles are particularly suitable for pressureless sintering); and, (f) high throughput per reactor volume can be achieved. In addition, the process used for generating particles determines the degree of sintering ability of the powders, since the process dictates the morphologies, the purity and its size distribution. In the future, thermal plasma synthesis nanometer size particles may play an important role in vapor phase reaction techniques and might be expected to be one of the first full scale commercial installations in the future."

Jan 1, 1998

By Deventer Johanna van

Ore bodies around the world are declining in grade, whilst increasing in complexity. The level of impurities relative to the valuable metal is steadily increasing, posing new challenges to existing operations. Ion exchange is widely used in the hydrometallurgical industry for both primary recovery of metals and the removal of impurities. The superior selectivity of ion exchange resins makes them exceptionally suitable for the removal of target impurities to very low levels, thereby saving operating costs, increasing the value of the final product and significantly improving revenue. The ion exchange process in these applications is very simple, using standard ion exchange equipment and acid regeneration. The process can be fully automated, requiring minimal operator interference and supervision Examples of impurities that are successfully removed via ion exchange include iron, antimony and bismuth from copper electrolyte. In the copper electrolysis process, antimony, bismuth and arsenic tend to form slimes which are dispersed in the electrolyte. These slimes contaminate the cathode and/or decrease the quality of the copper deposition. A special chelating resin was developed to remove antimony and bismuth, while at the same time ensuring minimal chloride leakage to the sulphate matrix. The work is described in more detail in this paper. Ion exchange is also used to remove copper, zinc and nickel from cobalt electrolyte. This paper addresses a few of these examples in more detail.

By Nils Eivind Kamfjord, Mari K. Næss, Gabriella M. Tranell

"In oxidative ladle refining (OLR) of silicon, the metal surface is oxidized resulting in the formation of a condensed silica fume (SiO2). In the current work, industrial measurement campaigns were performed aiming to measure the fume generation during OLR. A thorough discussion of the possible mechanisms has been included in order to improve our understanding of the Si(1)-O2(g) system.The measurement campaigns were performed at the Elkem Salten plant in Norway. In addition to fume generation from OLR, the metal temperatures and ladle purge gas amount were recorded. The results of this work suggest that fume generation during OLR results from splashing of the metal and/or oxidation of the metal surface, with oxygen transport to the metal surface being the limiting factor. Other mechanisms of SiO2 formation were investigated, however insignificant.IntroductionOne of the main environmental and economical challenges facing the metallurgical industry is fugitive emissions of both materials and energy. In the production of metallurgical grade silicon (MG-Si), refining of the silicon generally takes place through an oxidative ladle treatment (purging with an air-O2 mixture). In the refining process, exposure of silicon to air results in the formation of condensed silica fumes (SiO2) – one of the main sources of fugitive emissions in silicon production plants. The oxidation of liquid silicon, as opposed to solid silicon, has not been widely studied and described in the literature [1], thus a thorough investigation of the oxidation mechanisms, and factors affecting the oxidation reaction rate are essential in order to deal with the problem. In the current work, the rate of liquid silicon oxidation has been studied through industrial measurements of fume generation from refining adles, where the purge gas rate and composition have been varied. The results from these measurements were discussed in light of existing models describing the liquid silicon oxidation kinetics."

Jan 1, 2011

By Dachun Liu, Wenlong Jiang, Guozheng Zha, Liang Hu

In this paper, a novel technique for recovery of gallium and arsenic by thermal decomposition under vacuum is presented. The effects of distillation tem- perature on the volatilization behavior of each component were investigated. Theoretical calculations and experimental studies have shown that the method is feasible. The results show that under optimum conditions, highly pure Ga can be extractedwithadvantagesoverconventionaltechniques,includingsimpleoperation andenvironmentalfriendliness.Forexample,metallicgallium(purity > 99.99%)is obtained at 1273 K after 3 h under 3–8 Pa. Arsenic is obtained in the form of a elementary substance which could be preserved with relative ease. (cid:1) (cid:1)

Mar 1, 2018

By Chang-hong Peng

Solubility phase equilibrium in the ternary system of Me2+-NH4+-SO42--H2O (Me2+ represented Mn2+, Zn2+ and Fe2+) was studied by the isothermal method at 298K and physicochemical properties of the saturated solution such as density, refractive index and pH were also investigated. The experimental results show that the solubility isothermal phase diagrams of these systems consist of three invariant branches, two invariant points and three crystallization fields. Corresponding to the three crystallization fields, there have three phases of solid, that is MeSO4?nH2O, (NH4)2SO4 and (NH4)2Me(SO4)2?6H2O, respectively. At the eutectic point, the concentration and the refractive indexes of the saturated solution change evidently. Otherwise, the pH value change slowly in all the systems. The calculated results of the density and refractive index agree with the experimental results.

Jan 1, 2006

By Kazuhiro Nisizono, Takashi Kuroki, Nobuyuki Mori, Keisaku Ogi

"The improvement of critical current density and mechanical property is essential to the practical application of the superconductive oxides. A solidification technique is developed in this study for the growth of columnar or single Y123 crystal with finely dispersed Y211 and Ag particles through a monotecto-peritectic reaction of Li.(Ba-Cu-Ag-0 rich liquid)+ Y211-+ Y123+Lz(Ag rich liquid). The large solidification rate and temperature gradient can refine the Ag and Y211 particles. But Ag-free region is widely formed along the crystal growth direction in the central part of the Y123 cell. Since this phenomenon occurs because of the cellular growth, it is necessary to narrow Y123 cell width or to grow Y123 crystal with flat freezing interface. By controlling crystal growth direction using a seed crystal, Y123 columnar or single crystal with uniformly dispersed fine Ag particles are obtained. The· behavior of Ag and Y211 particles during the solidification of Y123 crystal is simulated by the peritectic growth model of faceted Y123 crystals.IntroductionY-Ba-Cu-0 superconducting oxide (YBCO) with high critical temperature also has excellent superconducting characteristic under the high magnetic field. The critical current density (Jc) has been enhanced by ·using unidirectional-solidification technique, which can overcome the weak-link problem at grain boundaries and control the crystal orientation and the distribution of Y211 particles which give effective magnetic flux pinning centers in the Yl23 matrix [1-4].In addition to improving superconducting properties, it is necessary to improve mechanical property for the practical application. The silver addition to the melt-textured YBCO superconducting oxide has been reported as the effective method to improve mechanical properties without degrading superconducting properties. Since the material properties are considered to be largely affected by silver particle size, form, dispersion state etc. in the Y123 phase, it is important to control Ag distribution in YBCO/Ag composites. Besides, it is also reported that the silver addition improve the corrosion resistance to the water and CO2 [5,6]. Nishizono et al. [7-9] have reported that the silver distribution in the YBCO/Ag composites is largely affected by the solidification condition, but yet some unclear points are also remained. YBCO has been also fabricated by the zone melting method [10-12], and Furuya et al. [5] and Hirano et al. [13] have reported the fabrication of silver added YBCO composites, but the distribution and behavior of Ag are not investigated in detail"

Jan 1, 2000

By Sevinc Yildirim, Cigdem Oruclus

"Metal-Porous Silicon (PS) based structures dipped in water show the direct hydrogen fuel cell behavior. The effect of the thickness of the cupper (Cu) film on the electrical properties of direct hydrogen fuel cell is studied by fabricating Cu/Porous Silicon/n-Silicon/Indium structures. PS samples were produced electrochemical etching of n-type single crystalline silicon with a resistivity of 1,25 Ocm and (111) orientation. The thin films of Cu with different thickness between 200 and 600 nm were deposited on PS surface by electron-beam technique. Investigation of the effect of Cu layer on the performance of the structure indicates that the performance parameters such as open circuit voltage (Voc) and short circuit current (Isc) strongly depend on the Cu layer thickness. It was observed that the divice with an 350 nm Cu layer exhibits the highest open circuit voltage (0,5 V), short circuit current (0,01 mA) and power density (10 W.m-2).IntroductionHydrogen is the most attractive and ultimate candidate for a future fuel and an energy carrier. Hydrogen is recognized as the environmentally desirable clean fuel of the future since it can be used directly in different types of hydrogen fuel cells [1]. In the past years, the rise in portable electronics requires the development of miniature fuel cells compatible with standard silicon micro fabrication technology. Most silicon micro-fuel cells have used the polyperfluo-rosulfonic acid membranes (Nafion R) as a proton exchange membranes (PEM) that is not really integrated with standard micro fabrication techniques [2-5]. The composite materials such as inorganicorganic hybrid materials (Nafion-silica, Nafion-borosiloxane etc) are next generation of proton conducting membrane [4-8]. But, fuel cells run on pure hydrogen gas, which can be produced with other energy resources. Hydrogen smallest atom and thus the H2 gas can leak easiliy. The application of hydrogen for power sources has been greatly restrained due to the lack of safe and convenient generation and storage methods.A kind of hydrogen fuel cells Metal-PS-Si structures used as an energy water directly. There is no need pure hydrogen. Cu-PS-Si Schottky-type fuel cells with as proton-conducting membrane and the thin-film cupper catalist and water as fuel, which are interesting for fabrication of lowcost miniature fuel cells. Generation of the open-circuit voltage and short-circuit current has been observed by Cu-PS-Si structure dipping in different hydrogen-containing solution."

Jan 1, 2014

By Yu Hu, Gabriella Tranell, Song Zhang, Eivind Johannes Øvrelid

"In the present research, recycling feedstock of silicon for Photovoltic (PV) application is investigated. Whether these recycling feedstocks are reliable in the future use is discussed in this work to assess the properties of the crystal silicon ingot, which is commercially pulled from top-cuts of casted multicrystalline ingot via one kind of Czochralski method - FerroTech. Dopant is the acceptor type Boron (B) and growth direction was <100>. Crystal diameter and the length were 190mm and about 1700mm, which were controlled by the temperature and the pulling speed, then cut to 156mm * 156mm wafers with 2000um and 200um thickness. Resistivity measurements of these wafers by Four Point Probe (FPP) are in good agreement to the calibrated profile after Rapid Thermal Process (RTP). In this work, the Minority Carrier Lifetime MCI, shown by Carrier Density Image (CDI) and Quasi Steady State Photo Conductance (QSSPC), gives the mapping results on the cross section and the relationship to the injection level, increases in an arrange from 40us to 90us along the ingot height, which is abnormal distribution compared to the standard ingot. Then Oxygen and other metal impurities distributions, measured by Flourier Transform Infra - Red (FTIR) respectively, account for the novel phenomenon of the continuously increased MCI. Various types of heat treatments were performed on these wafers (different ingot and different positions) in N 2 and 0 2 mixture atmosphere. Before and after heat treatment, micro-defects were revealed by copper decoration and etching work. Solar cells are fabricated by Energy Research Center of the Netherlands from the experimental ingot, and processed under an industrial standard line. Compared to results of the reference mono-crystalline and multi-crystalline silicon solar cells, the performances of experimental ones show excellent efficiency values up to 18.5%, and Jsc values up to 37mA/cm2.IntroductionThe PV industry has gone through rapid development, with a high growth rate resulting in an increasing demand for silicon feedstock. In addition, costs in production need to be reduced such that solar energy can compete other conventional and renewable energy. Searching low cost, reliable and efficient feedstock is one promoting way to improve and enhance the competitiveness of the PVindustry.More and more researchers start searching new raw materials for PV application [1]-[4]. The key to make full use of low cost raw materials is to control the distribution and effect of impurities, such as Carbon, Nitrogen, and other metal contamination [5]."

Jan 1, 2013

By Shadia J. Ikhmayies

"Cadmium sulfide (CdS) in the form of thin films is an interesting material because it has a large variety of applications ranging from photovoltaic to luminescent devices. N-type CdS is usually used as a window layer in the heterojunction CdS/CdTe thin film solar cells. A review of the photoluminescence (PL) spectra ofn-type CdS thin films prepared by different techniques was performed. The effects of different dopants and impurities and the effects of temperature and deposition parameters on the PL spectra were discussed. Annealing in different atmospheres causes the changes in material structure and phase change from cubic to hexagonal phase which can be detected through the variations in the PL spectra. CdCh heat treatment improves the cystallinity of the films and enhances the exciton peaks and the green band in the PL spectra.IntroductionThin CdS films deserve attention because their expected gap emission lies very close to the highest sensitivity of the human eye. Thus, one might assume that thin CdS films are an appealing host for photonic devices [ l]. They have been used in a lot of applications including electronic and optoelectronic devices [2]. Thin films ofn-type CdS are widely used as a window layer in heterojunction solar cells such as CdS/CdTe solar cells. Doped and undoped CdS thin films can be obtained by different techniques such as; spray pyrolysis (SP) [3], chemical bath deposition (CBD) [2, 4], pulsed laser deposition [5, 6, 7], laser ablation [l], thermal evaporation [8].Several experimental techniques have been used in order to study semiconductor defects. In particular, photoluminescence (PL) has been shown as a powerful and sensitive tool in examining the crystal quality of polycrystalline thin films. PL can be used in the detection of defects which are radiative active. These defects can also act as traps in the transport of carriers [9]. The photoluminescence (PL) of thin film CdS is strongly influenced by the unbalanced stoichiometry, which is typical for CdS and is in general evoked by a Cd surplus. With increasing Cd content, the emission spectra move far below the gap to the red spectral range. Besides stoichiometry problems, independent of the material deposited, the PL properties of thin films depend on surface features and the influence of the interface between the film material and the substrate [10]."

Jan 1, 2013

By D. F. Liub, Z. Y. Liu, W. Y. Xue, Y. F. Shenb, Y. D. Wang

"The microstructure characteristics and deformation behavior of ultrafme grained (UFO) 304SS fabricated by accumulative rolling and armealing have been investigated by means of tensile tests, electron-backscatter-diffraction (EBSD) and transmission electron microscopy (TEM) techniques. The volume fraction of martensite phase decreases with increasing armealing temperature. In the grain sizes ranging from 300 nm to 10 µm, the strength held Hall-Petch relationship. The sample with an average grain size of 300 nm exhibited extra high yield strength of 1700 MPa and a tensile strength of 1780 MPa, while the elongation retains 12%. The limited uniform elongation in the UFO materials could be explained in terms of plastic instability. Very interestingly, for the bulk material with an average grain size of 1.200 µm, the high yield strength and uniform elongation were simultaneously achieved to be as 1000 MPa and 18%, respectively.IntroductionUltra-high strengths have been achieved in elemental metals by employing heavy plastic deformation, or by creating ultra-fine-grained (UFO) structure. Here UFO materials are defined as polycrystalline solids with property-controlling microstructural features below the 1 µm level. Typical processing routes include severe plastic deformation (SPD) [1, 2], which decomposes the grains through dislocation accumulation and reorganization (polygonization). Several different kinds of SPD process for bulk materials are typically as equal-charmel angular pressing (ECAP) [3], high-pressure torsion (HPT) [4] and accumulative roll-bonding (ARB) [5]. One of the main motivations for such a push for the very small grain sizes stems from the expectation of unprecedented mechanical strength, as predicted by the well-known Hall-Petch relationship that projects a continuous rise of strength with decreasing grain size [6]. However, these ultra-high strength metals no longer have the high ductility typical of their conventional coarse-grained counterparts, because the undesirable inhomogeneous deformation on the microstructure level can lead to the early onset of failure, severely limiting the useful ductility [2]. Recently, the interesting strategies have been performed to increasing simultaneously the ductility and strength ofUFG pure copper and nanostructured alloys by Zhao et al [7, 8]. In a pure copper, a high ductility has been achieved without sacrificing strength by introducing a high density of pre-existing twins and a large fraction of high-angle grain boundaries. Their encouraging results trigger our motivation to obtain high strength and ductility from the commercially bulk material."

Jan 1, 2013

By W. G. Davenport

The Cu content of industrial flash furnace concentrates varies considerably. It is usually around 30% Cu (Tables 2.1, 3.1) but it may be as high as 55% Cu and as low as 20% Cu. The mineralogy of flash furnace concentrates also varies. The most common Cu mineral is chalcopyrite (CuFeSz), but many concentrates contain bornite (CuSFeS4), chalcocite (CU2S), covellite (CuS) and even native copper (CUO). Pyrite (FeSz) :is also present in many concentrates. This chapter examines how concentrate composition affects flash smelting -with specific reference to &apos;low-Cu-grade&apos; FeS2-CuFeSz concentrates. Chapter 14 does the same with &apos;high-Cu-grade&apos; CuzS-CuFeSz?concentrates.

Jan 1, 2001

By Alexander Burns

Electrolytic salt splitting is a technology where acid and/or base is regenerated from a neutral salt using membrane electrolysis. Recent advances in the understanding of brine treatment, membrane stability, and cell design have made electrolytic salt splitting feasible on certain hydrometallurgical solutions. Meanwhile, environmental regulations have made the bulk disposal of salt solutions more difficult. In this paper, sodium sulfate salt splitting is examined from a cost perspective, compared to purchasing the reagents directly. Relative costs are estimated for several regions based on published electricity and reagent prices. The results show that salt splitting is economically favourable in some regions, and can be made more favourable by applying modifications to the traditional three-compartment desig

By Chi Ru?an

Sollutions of ammonium chloride, nitrate and sulfate were studied in extraction of rare earths absorbed on a low-grade, kaolilnitic ore recently discovered in southern China. The results of percolation leaching tests and the recovery of the rare-earth values from these solutions are presented.

Jan 1, 1989

By Greg Andrews, David Dreisinger

The Foxtrot deposit of Search Minerals contains a range of rare earth element containing minerals including allanite, fergusonite and bastnasite. The Search Minerals Direct Extraction Process for treating these minerals involves coarse crushing of the ore to -6 mesh (3.45 mm), acid treatment at 200 °C in a novel reactor configuration, water leaching, various purification steps to reject iron, aluminum and uranium/thorium (present in small amounts) and finally precipitation of rare earths as an oxalate and calcination to form a mixed rare earth oxide product for refining. The economics of the process are presented.

Mar 1, 2017

By Monica C. Pinto, Gustavo H. Nalon, José C. L. Ribeiro, Rita de C. S. S. Alvarenga, Leonardo G. Pedroti, Lucas A. F. Fioresi

This study aims to evaluate the influence of mortar’s mechanical properties on the behavior of clay masonry. Experimental studies were performed using prisms of clay blocks under axial compression. The clay units were produced with a clay from Tres Rios, Rio de Janeiro, Brazil and had compressive strength of 4.9 MPa. Two mortar compositions were used, which had compressive strength of 94.7 and 50.4% of the clay blocks’ net area compressive strength. It was noticed a slight increase on the prism’s compressive strength with the increase of the mortars’ compressive strength and stiffness. Prisms made with flexible mortars had a ductile failure and collapsed under lower compressive stresses, while prisms made with stiff mortars resisted higher compressive stresses, but had a brittle failure ,crushing the blocks. A very strong mortar is not recommended. Using more flexibl mortars does not compromise the strength and stiffness of the masonry and prevents an excessively brittle failure of the structure.

Mar 1, 2017

By Deborah A. Kopsick

Several minerals were observed and collected in a small gully originating from a weathered coal processing waste (gob) pile in Barton County, Missouri. The rapid alteration of these various minerals after collection suggested that they might represent a dehydration sequence. X-ray diffraction of the dehydrated and rehydrated minerals deposited on the gob pile indicated the presence of the monohydrate and heptahydrate forms of ferrous sulfate, szomolnokite and melanterite respectively. The occurrence of melanterite (FeSO4.7H2O), was limited to isolated areas of ponded water while szomolnokite (FeSO4.H2O), was associated with the outwash areas of the pile. Laboratory dehydration of melanterite collected at the gob pile revealed the formation of rozenite (FeSO4.4H2O), an intermediate form of ferrous sulfate. Szomolnokite was shown to be the stable form of these ferrous sulfates during these experiments while melanterite and rozenite were shown to alter readily. Chemical analysis of szomolnokite revealed enrichment in Fe, Mg, Zn, Cd, Cu and Mn relative to the chemical composition of the gob ad the lechate generated from the gob wastes. Although this gob pile had been weathering for more than 35 years, significant concentrations of trace metals were still being released from the pile through the generation of leachate and the formation of various soluble metal enriched ferrous sulfate minerals.

Jan 1, 1982

By Jorge A. S. Tenorio, Pedro F. A. Prado, Denise C. R. Espinosa

There is an increasing challenge of waste management regarding the growth of photovoltaic (PV) technology. Often overlooked by its environmental benefits of greenhouse gas emission reduction, PV technology contain metals that are highly hazardous for the environment. Amorphous silicon (a-Si) PV modules employ indium-tin-oxide as transparent conductive oxide and given the high price of indium its recovery could be advantageous from an economic perspective as well. Leaching of indium was predicted by comparing the Pourbaix diagram with the values of oxidoreduction potential and pH measured on a phosphoric acid solution. The a-Si panel was subjected to thermal treatment to remove the proprietary, protective coating and allow leaching to occur. Then, indium could be leached by phosphoric acid in a jacketed reactor, reaching a concentration of 55 ppm (67% leaching rate) with a 0.2 g/mL of a-Si panel to aqueous solution ratio. The leaching of indium with phosphoric acid is novel and could open doors for many other recycling routes for solar panels.

Mar 1, 2018

By John M. Gaines

Lead concentrates from the Viburnum Trend in Southeast Missouri are sintered, prior to smelting, to bind the particles together, homogenize the feed, and reduce the sulfur content. About 20% of the sinter at some plants is classified as bad sinter. A total of 130 samples of good and bad sinters were studied by reflected light microscopy, scanning electron microscopy-energy dispersive analysis, and electron microprobe analysis to characterize their differences in mineralogy and textures. Good sinters consist predominantly of hardysonite, franklinite, lead silicate matrix, and large crystals of calcium-magnesium-iron silicate, together with minor amounts of lead oxides, lead-zinc silicate, metallic lead, specular hematite, magnetite, lead-iron-bearing zincite, and zinc-lead-magnesium-bearing wustite in a tightly intergrown mesh of crystals and with an evenly distributed porosity of about 15-20%. Bad sinters contain larger amounts of lead silicate matrix, galena, metallic lead, and lead oxides, but smaller amounts of hardysonite, franklinite, and calcium-magnesium-iron silicate, lack intimate intergrowth of the phases, and have lower (0-5%) and unevenly distributed porosity.

Jan 1, 1992