Search Documents

By Wilhelm Brandstätter, Johannes Steiner, Alois Triessnig, Christian Redl

"The results of numerical simulations of bubble detachment from an orifice in a horizontal plate submerged in liquid are presented. The bubbles are created by forcing gas through this orifice into stagnant liquid. The simulations are performed with a two-dimensional incompressible Lattice Boltzmann (LB) scheme. In previous works the same problem was investigated by two-phase simulations in which surface tension effects were considered by an interaction potential formulation between the phases. In contrast, in the present work a volume of fluid (VOF) model consisting of a carrier fluid and a passively advected scalar function for the calculation of gravitational and surface tension forces, respectively, is used. The aims of this study are to examine the applicability of the one-phase LB method to the numerical analysis of bubble formation and to verify the theoretical and experimental predictions of the dependencies of the departure diameter on gravitational forces, surface forces and wettability effects. To this purpose the simulations were performed at different values of gravitational acceleration g, surface tension coefficient s and contact angle ß. Nonlinear fits to the data yield functional dependencies which are in good agreement with the predictions. IntroductionBubble formation behavior is an extensively studied subject, especially in chemical engineering, power industries and metallurgical processing. Knowledge of the underlying physics of bubble motion is, for example, required for the design of chemical reaction towers and agitation tanks. Another important application is the argon gas injection through the wall of the tundish nozzle into liquid steel stream to deter clogging with solid inclusions. Argon bubble motion and its effect on flow depends greatly on different parameters, e.g. gas flow rate and size of the bubbles. Thus, if these bubbles are not managed properly, they can become encapsulated upon solidification and result in undesirable impurities in the material [1, 2]."

Jan 1, 2004

By Zenjiro Asaki

The copper concentrate particles dissolve quickly into the molten matte in the smelting furnace of Mitsubishi Process, which indicates that the sulfide smelting is essentially a gas/liquid reaction. In this paper, theoretical calculation has been made on the rate of oxidation of FeS component in the matte to form FeO by rising gas bubbles using the penetration theory. The results showed that all the oxygen in the bubble of 1.2 cm in diameter, which is the maximum stable diameter, is consumed in 3 ms. This time required is sufficiently short, and it results in the actual operation of smelting furnace of 1100% oxygen-efficiency. These calculations indicate that most smelting reactions are completed just under the lance, except slag formation.

Jan 1, 2002

By Stefan Mutz

In Germany the automobile recycling is regulated by law. Current legislation requires that by the year 2015, eighty five w.-t. % of the components from used cars ill be materially recycled. Whilst for 10 w.-t. % of the materials a thermal utilization is certified, there are still some concrete questions that remain unanswered regarding the usability of single fractions. The recent innovative approaches to the concepts of used cars dismantling do not alter the fact that the majority of the materials of used cars still have to pass over the shredder and the connected processing aggregates. The status of the so called SLF (Shredder light fraction) which is about 25 w.-t. % w.-t. in used cars, has not been satisfactorily clarified. Furthermore questions still remain regarding the separation of the NMSF (nonmagnetic metal shredder fraction) which has to be separated in the single metallic fractions like stainless tell, copper, brass, zinc, etc. Attempts of optimization can be found. This paper analyses some of the difficulties being encountered by the automobile recycling industry in Germany, before reviewing some of the innovative approaches that the industry has introduced. Finally the paper goes on to describe the potential of automatic picking. Examples of a series of tests, utilizing this technology, in which a variety of products from a range of shredders were isolated are described in detail. This new technology provides a range of applications to the automobile recycling industry.

Jan 1, 2002

By Ali Nadir Khan

Depleting copper resources and advancing technologies have challenged industries to develop more viable, adaptable and cost efficient processes using also secondary raw materials in copper production. This study is targeting to that goal by dynamic modelling of flow and heat transfer coupled with chemical kinetics in an industrial scale flash smelting furnace settler using commercial CFD software ANSYS Fluent. First, different physical phenomena occurring inside the settler, for example, settling and separation of the matte/slag phases, and heat transfer between slag/matte phases and settler walls are studied. Secondly, reaction kinetics between matte and slag, and between slag/matte and settler walls, and impurity element distribution will be studied. This would also include phase changes phenomena due to these reactions and the flow of the reaction gases inside the settler. Settling of polydispersed droplets, their coagulation, breakage, and WEEE particle behavior are further targets of the modelling work.

By Iain B. Mackenzie

In 1997, a thin layer of Microtherm Microporous Insulation was used to replace fireclay brick behind the magnesia/chrome working lining in #5 refining furnace at BHP?s San Manuel AZ smelter. A 23°C reduction in shell temperature was obtained, together with a large increase in the working capacity of the vessel. There was no sign of metal penetration as a result of the increased insulation. Following these highly favorable results, BHP have introduced this product into all of their refining furnaces.

Jan 1, 1999

By Daniel K. Lindberg, Fiseha Tesfaye

To reduce the use of fossil fuels and increase self-sufficiency in energy, nowadays, there is an increasing interest to produce heat, power and transportation fuels from renewable resources. Solid biomass is one of the most important renewable energy sources for meeting this target. However, fouling, slagging, and corrosion threaten long-term operation availability and costs of biomass power plants. Slags accumulated on the surfaces of superheaters, which decrease thermal efficiency, often constitute a considerable percentage of complex inorganic phases. However, thermodynamic properties of the complex inorganic phases and their combined effect, which will help to deal with the slag related problems during high-temperature biomass combustion processes, are not well known. In the present paper, thermodynamic properties of K-, Ca-, and Na-based inorganic phases and their mixtures under different gas conditions are both critically reviewed and experimentally studied. The obtained results are presented and discussed.

Mar 1, 2017

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Torben L. Edens

Norddeutsche Affinerie is the largest copper producer in Europe. Two sites are in operation for the production of refined copper: primary copper production is located in Hamburg and secondary copper production in Lünen. A total of just under 560,000 tonnes of copper cathodes is produced annually at the two sites. Primary copper production using the flash smelter furnace has been in operation in Hamburg since 1972. Over the years, the capacity of the flash smelter has been increased in three expansion projects from 120,000 t to almost 500,000 t of anode copper p.a. The anode sector consisting of two anode furnaces and a 24 mould casting wheel still features just about the same equipment as in 1972. The paper describes the most important steps taken to optimise operation which have put NA in a position to cast meanwhile more than 500,000 t of anode copper annually with the two anode furnaces and 24 mould anode casting wheel.

Jan 1, 2006

By Burcu Ertug, Necip Ünlü

"On average, one out of two glass bottles coming on to the market is provided by recycling processes in Europe. Glass recycling has been started by the early of 1970s in Turkey, and the recycling amount has been reached to 70 thousand tons recently, while 4.2 million tons which represents only 25 percent of total glass manufactured, is the amount of glass collected annually for recycling in the world. The glass recycle process basically involves collecting, sorting, then crushing and grinding after which glass cullet is produced as the secondary raw material. Removing of the contaminants from the glass cullet, and then melting are the next steps. In this study, recent developments of 100% recyclable without any deterioration in quality, and never decomposable glass, are discussed detailed in terms of glass production processes.1.IntroductionIn many countries, waste glass constitutes a large proportion of solid wastes, and recycling the glass is a major environmental problem all over the world [1]. Among the diverse types of waste, glass is one of the most valuable recycling materials because it can be revived and recycled completely and hardly decomposes [2]. Between 80% and 85% of the mass output from the worldwide glass industry is either in the form of containers for the food, beverage, and pharmaceutical industries, or flat glass for building construction or for motor vehicle manufacture. Other product segments, whilst only constituting about 15% of the mass output, produce high value technical and consumer products by comparison with container and flat glass [3].In the present study, the recycling of Liquid Crystal Display (LCD), Cathode Ray Tubes (CRT) and Printed Circuit Boards (PCB) were examined. The production of glasses and glass-ceramics from glass cullet, synthesis of different compounds from recycled glass were other subjects of interest. The use of recycled glass for construction industry and using glass as aggregate were emphasized. Finally the recovery of glass fibers were investigated."

Jan 1, 2012

By Ricardo A. Valls

The Sechol Nickel-Cobalt Laterite Project is located in East-Central Guatemala, 140 km northeast from Guatemala City. In-situ resources in the immediate Sechol area, including those on other mining concessions contain 133 million tonnes of mineralization, grading 1.5 1% nickel. Considering the ever-increasing market for these metals, and the potential quick return on the initial investment, Jaguar Nickel Inc. is confident that by late 2006, it will be producing the first nickeltcobalt hydroxides from Guatemala. The path from now until the production stage passes through a pre-feasibility study, scheduled for completion by mid 2004, and bankable feasibility by mid 2005. Jaguar's objective, however, is not only to have a producing nickel-cobalt mine by late 2006, but also to continue with the exploration work in order to make Guatemala one of the world's leading nickel-cobalt producers. The Sechol group of deposits is conformed of several lateritic pockets, delimited by tectonic faults, and hosted by ultramafic rocks of the Sierra de Santa CW. ophiolitic belt that intruded the Maya Continental Block during the Early Tertiary age. The intrusive is mainly represented by a layered sequence of dunites, peridotites, and pyroxenites, usually strongly serpentinized. Existing data indicate that these rocks underwent fractional crystallization, and probably some degree of magma mixing and contamination previous to their main tectonic event. The most complete profiles are usually present over weathered dunites and serpentinites, while on top of the less altered pyroxenites, there is usually the formation of only a limonitic zone. The relative complexity of the ophiolitic belt explains the variety of mineral resources in the area, which include Ni-Co-Fe laterite, chromite, bauxite, magnesia, and also has the potential for gold, PGMs, and precious and semi-precious stones such as jade, nephrite, and chrysoprase. Metal recovery from the Sechol deposit will be based on an atmospheric chloride process, followed by solution purification, production of an intermediate nickellcobalt hydroxide suitable for sale, and finally acid and magnesia recovery by standard spray roasting technology. The chloride process will allow exploitation of the whole lateritic profile to produce 20,000 Mt of nickel hydroxide and 800 Mt of cobalt hydroxide per year. The exploration work completed to date has concentrated mostly on the Sechol group of deposits, representing less than 5% of the current land position of Jaguar in Guatemala. Within Sechol, the company has identified a large pocket of more than 5 Mt of laterites grading 2.1% nickel and 0.08 % cobalt as a startup pit "El Inicio". Including the work previously completed Keywords: Laterite deposits, Ophiolitic Belts, Central Guatemala, Nickel, Cobalt

Jan 1, 2004

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2 versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Lv Guozhi, Ren Xiaodong, Liu Yan, Dou Zhihe

"This paper investigated a new desulfurizer, dolomite and ferrosilicon. Magnesium vapor produced by silicothermic reduction of dolomite and ferrosilicon in an immersion tube of molten iron was injected into the molten iron by carrier gas through the underpunch of the tube and desulfurization reaction occurred. In order to explore the desulfurization process of molten iron by the new desulfurizer, the thermodynamics, and experiments of magnesium vapor production and desulfurization have been studied. Through thermodynamic calculation, the reaction temperature of magnesium vapor production by 75ferrosilicon and light-burned dolomite is 1838K in the standard state and decreased with the decreasing partial pressure of magnesium vapor, PMg· When PMg=25kPa, the reaction happens at 1673K. From experiments of magnesium vapor production, reduction efficiency of Mg vapor is about 60 % in 15 minutes at 1673K. From hot metal experiments, the desulfurization efficiency is 89.35%, and the lowest sulfur concentration after desulfurization is 46ppm.IntroductionPretreatment desulfurization of hot metal has become a necessary step in modem optimizing steelmaking process for its cheap cost, which can not only liberate of blast furnace productivity and reduce the burden of produce steel, but also effectively improve overall economic efficiency of the iron and steel system[l-ZJ_ At present, injection magnesium particle is one of the two main methods of desulphurization in hot metal owing to its strong affinity for sulphur, low amount of slag produced, low iron loss in slag skimming and low equipment investment[3l. However, there are still some insufficiencies on the hot iron pretreatment with magnesium particles at present[4-5l"

Jan 1, 2013

By Jose Carlos D'Abreu, Edelink Efrain Tinoco Falero, Mauricio Marcos Otaviano

The production and consumption of Direct Reduced Iron (DRI) are continuously increasing, as a consequence of the impact of shale gas extraction technology on the Natural Gas (NG) market. Considering this context, DRI may improve the Blast Furnace (BF), Electric arc Furnace (EAF) and LD converter ’s productivities and consequently their competitiveness. In this work the results of a cooperative research conducted by PUC-Rio University and a Brazilian mining company are presented. Laboratory-scale simulation tests, using DR commercial pellets and typical industrial operational parameters of a benchmarked DR shaft furnace, were conducted and planned using statistical and factorial analysis. In the simulated experiments, the following three regions of the DR shaft furnace were considered: Reduction Zone (RZ), Transition Zone (TZ) and Cooling Zone (CZ). Three stages were considered in the research development: (i) the reactions and equations concerning pellet metallization and Carbon precipitation were analyzed; (ii) experiments focused on the de finition of the carburization kinetic equations occurring in the Transition and Cooling zones, and finally, (iii) aimed to develop the “METCARB” model, a computational program conceived to simulate mathe- matically the metallization and carbonization reactions along the height of the furnace. In conclusion, a comparison is made with industrial results in order to validate the resulting “METCARB” model.

Mar 1, 2018