Search Documents

By B. J. Jody

This paper describes a one-step thennal-treatment process, developed at Argonne National Laboratory, to remove all organic contaminants from the glass-fiber waste that is generated during the glass-fonning process. The recovcred glass fibers can then be recycled into new glass fibers or new glass products without adversely impacting the operations of the glass industry or the quality of its products. Our process involves shredding the waste to a manageable size and then processing it at temperatures below its melting point to remove the polymeric-coating layer. The glass industry generates more than 60,000 tons of glass-manufacturing waste annually in the glass-forming process alone. Recycling of this waste stream can keep this non-biodegradable waste out of the landfills. In addition, use of recycled glass lowers energy costs, by an average of about $5 per ton as compared to using virgin raw materials to make virgin glass fibers. This process will also reduce the emission of C02 by 17,400 tons a year and it will also reduce the emission of nitrogen oxides. Economic analysis of our process shows a potential payback of less than 2 years.

Jan 1, 2003

By A. M. Alfantazi, M. Boissoneault, D. B. Dreisinger, J. Synnott

"The effects of five commercially available foaming reagents (range of 0 to 25 ppm) namely Dowfroth 250, Saponin, Yucca, Licorice and Meta-Para Cresol on acid mist control, current efficiency, polarization behavior, and deposit morphology and orientation were investigated. The deposition was carried out using a bench scale electrolysis apparatus (cell volume 3L) at 500 Nm-2 and 38°C for 3 hours from Kidd Creek zinc electrolyte. The acid mist control capability of the various reagents was studied and compared by characterizing the foam layer generated during actual electrowinning conditions and by direct quantitative measurements of acid mist levels on top of the electrowinning cells. Within the range considered, the addition of these reagents reduced the current efficiency, refined the grain size of the deposit, and changed to preferred orientation of most of the deposits. Among the reagents tested, acid mist measurements indicated that Licorice and Dowfroth 250 were the best acid mist suppressant at emissions of 0.30 mglm3 and 031 mg/m3 respectively while Yucca and MPC produced the most mist at 3.0 mg/m3 and 33 mg/m3 emission rates, respectively.IntroductionMost of the world's primary zinc is produced via a combined roast-Ieach-purificationelectrowinning process. Depending on the electrolysis conditions, several additives may be added to the electrolyte. Some (e.g. glue, antimony, sodium carbonate) are added to mainly counteract the detrimental effects caused by impurities while others (e.g. licorice, Saponin) are used as foaming reagents to prevent excessive acid mist formation. Acid mist emission is a problem in many electrolysis operations because it corrodes the equipment and is a health hazard to the workers in the tankhouse as well as it pollutes the environment. Due to recent trends towards more environmental protection and more stringent in-plant hygiene, there is an increasing need to minimize these aerosols. In order to eliminate or minimize these aerosols foaming agents are usually added to the electrolyte to produce a foam layer on top of the electrolyte, thus trapping most of the mist. The ideal foaming agent would trap all of the mist and would not interfere with the electrowinning process. It is also evident that the reagent toxicology, cost and availability are important factors that need to be considered.Review of the available literature clearly indicated that very little work has been done in the past on the subject of acid mist control in electrowinning operations particularly in the area of foaming and anti-misting properties of surfactants. Two papers [1,2] have reviewed briefly the existing technologies for acid mist control. Recently, most of the work in this area has focused on the development of special mechanical devices that could be attached to the electrodes and control the mist generation at the source before it is emitted to the cellhouse [2-5]. On the other hand, extensive body of literature exists that deals with the effects of anti-misting reagents on the electrowinning aspects [6-7]."

Jan 1, 1997

By V. V. Khristenko, V. I. Dubodelov, V. A. Seredenko, B. A. Kyryyevsky, H. V. Seredenko

"During the last decades investigators of many countries shows an increased interest to alloys which are characterized by miscibility gap in a liquid state. It is connected with essential possibilities of control of structurization in such alloys because of the melt at certain temperature parameters is · emulsion with disperse phase inclusions. These ensure essential influence ·on structurizations.The certain inclusions can play a role of lubrication ensuring ""wearless"" process. The sizes of inclusions of this phase can be rather large proportional to sizes of strengthening phase (up to 1000 nm). Other inclusions ensure process of strengthening of a main material. In this case requests to a dispersibility character of distribution and structure of such inclusions are much higher.The multicomponent alloys of system of copper - (Fe - Cr - C)- alloy concern to the number of advanced compositions. The copper alloys with structure of a type of a ""frozen emulsion"" in which strengthening phase· is a chromium pig-iron are characterized by high thermal stability in the extreme operating conditions. The mechanism of inclusions forming is emulsifying of a melt in miscibility gap at temperatures close to temperature of binodal under superimposition of external effects.The main complexity of producing of ware from such alloys is .a providing in their structure of necessary dispersible inclusions uniformly distributed all over the volume. Thanks to a selective action of electromagnetic fields on liquid phases with various electroconductivity relative velocity of phases is created and is regulated the ratio of their ""apparent"" specific gravity is changed. Excitation of pulsing force effects with the certain frequency on interphase surface allow actively to influence on process of a dispersion of a liquid metal medium."

Jan 1, 2000

By Bruce H. Baker

Studies of used or unused refractory materials are excellent examples of applied mineralogy in industry. Refractory materials are mineral substances containing ceramic or chemical bonding systems. Knowledge of the mineral composition, bonding, and textural relationships often explains the resulting physical property values of a refractory and contributes to the interpretation of refractory wear mechanisms occurring in steel plant service.

Jan 1, 1982

By P. Regan

Following the introduction of the Contilanod process over 10 years ago at Copper Range and IMI Refiners, significant changes and advances have been made to this pioneering anode production technique. A new radial flow metal feeding concept has been developed that allows a substantial increase in casting rates on the Hazelett® twin-belt caster. To cut the 45 mm thick continuous anode plate into shaped anodes at rates of 100 t/h or more, a filly moving hydraulic shear designed by Mannesmann Demag has replaced the slower speed plasma cutting torch. Details of the.new caster and shear are presented along with operating results from the new lines starting up in 1999 at the Gresik smelter/refinery in Indonesia and the completely revitalized Mansfelder Kupfer und Messing complex in Germany.

Jan 1, 1999

By S. W. Marcuson

Smelting of nickel-copper sulfide ores at Vale Inco’s Sudbury operations commenced in 1888 and the first converting plant went into operation in 1892. As the demand for nickel grew, the smelting operations expanded and by the 1960’s the Copper Cliff Smelter featured the longest converter aisle in the world with space for nineteen Peirce-Smith converters. During this long period, different converting techniques and vessels were employed. The evolution of converting is reviewed with special emphasis on the modifications made to the Peirce-Smith vessel to accommodate the metallurgical and process needs of the changing times.

Jan 1, 2009

By Hartmut Rossel

VAW aluminium AG has built a "Recycling-Technikum" (Recycling Research Centre) to add a new arm to the company's Corporate Research and Development Department. The Recycling Research Centre, a pilot plant for scientific research, has been in operation since September 1993. These state-of-the-art facilities allow the investigation and optimisation of recycling techniques in 'a global way and in detail. Research is concentrated on the unit operations - processing, melting and waste-gas purification - with the available installations making it possible to compare different alternative process combinations on a 100-kg scale. One of the main targets of VAW research is the development of recycling techniques for packaging. The paper presents an approach to recover the aluminium contained in flexible packaging materials using an integrated melting and waste-gas purification system.

Jan 1, 1995

By Seong-Jong Kim

The formation behavior and corrosion characteristics of anodic oxide films on pure Mg and Mg-AI alloys were investigated focusing on the effects of anodizing potential, Al content, temperature and NaOH concentration. Pure Mg and Mg-AI alloys were anodized for 10 min at 3, 10, 40, and 80 V in NaOH solutions. Mg(OH)2 was generated by an active dissolution reaction at the surface of the specimen and the product was affected by temperature while MgO generation increased with NaOH concentration. Moreover, the current density after anodizing for 10 min at a constant potential decreased with increasing AI content in Mg-AI alloys,

Jan 1, 2003

By René Winand

Due to chemical and electrochemical behavior of the most common additives in copper electrorefining i.e. gelatine, thiourea and chloride ions, it is essential to simulate as far as possible true industrial practice while performing laboratory experiments. The three additives must be studied simultaneously, and added continuously to the electrorefining cell. Ratio electrolyte volume to cathode area; ratio bleed flow to cathode area; hydrodynamic conditions; residence time of electrolyte in the cell; current density; electrolyte and soluble anode must be as near as possible to industrial ones. Experiments performed in the author's laboratory show that under these conditions, reproducible results can be obtained at normal industrial current density and at high current density as well. Problems are however still encountered when developing a sensor for additives monitoring, due to electrolyte redox potential and to substrate influenced thin layer deposition.

Jan 1, 1995

By Takashi Yoshida

"This paper will discuss the recent situation and future of the zinc industry from the technical point of view. It includes recent problems faced by the zinc industry and technological developments. One of the biggest problems of the zinc industry is raw materials. Traditional zinc concentrate becomes much complicated with respect to its chemical and physical properties. Thus, each process faced various problems. Also, secondary resources, generating so called recycling processes, become much more important. Recycling is, of course, a very important aspect for sustainable development of society. Secondary raw material also includes a great variety of impurities not included or very low levels in traditional zinc concentrate. Some problems are caused by these impurities. To overcome these problems some technological challenges have been taking place. Details will be discussed in the symposium.IntroductionZinc is a very useful metal based on its elechtro-chemical, chemical and physical properties. The most important usage is galvernizing of steel which is used for automobile, construction and a very wide range of other indutries. Also, zinc is used for dicasting and other alloys such as brass. Smelting of zinc is different from other metal because of its electro-chemical properties. Many parameters should be controled compared with other metals such as iron and copper. Typical zinc smelting processes are the Imperial Smelting Process (ISP) and the electlolytic process. The ISP process is a pyro-metallurgical process using a blast furnace. The electrolytic process is a hydrometallurgical process. Both processes are energy intensive, and the smelting process cost is increasing because of higher energy costs. The situation of the ISP is very severe because of higher coke prices. Recently, many ISP plants have been shut down because of economic reasons"

Jan 1, 2012

By Guodong Lai, Shixing Wang, Lijuan Chu, Jinhui Peng, Zebiao Zhang

"The beneficiation of poor manganese ores containing phosphate gangue is very difficult by conventional processes, because of the similarities in the physico-chemical properties of the constituent minerals. The shaking table gravity concentration process and concentrated strong acid selective intensified leaching process were used for dephosphorisation of Yunnan manganese ore. The leaching process was effective. The effects of intensified leaching time, solid-liquid ratio and particle size were investigated. The relevant leaching factors were optimized as -0.125+0.088 mm particle size with 68% nitric acid for 24 h when using a solid-liquid ratio of 1:1 at room temperature and atmospheric pressure. Under these conditions, the P/Mn ratio was reduced from 0.0107 to 0.0056, and the grade of manganese was increased from 12.32% to 42.76%. The dissolution of manganese during leaching was negligible.IntroductionManganese and its compounds are widely used in the iron and steel industry as deoxidation and desulfurization agents and as alloying additives [1-2]. Because of the increase in demand, low grade refractory manganese ores are becoming a new source. Many Chinese manganese ores are high in phosphorus, which cannot be used directly for metallurgical purposes. This occurs because phosphorus enters into the metal phase during smelting and its presence sharply deteriorates the mechanical properties of the metal [3-4].Kanungo and Sant [3] investigated the dephosphorization of phosphorus-rich manganese ores by selective leaching with dilute hydrochloric acid. They observed that leaching with dilute hydrochloric acid (0.1-0.6M) could reduce the phosphorus contents to the specified limit of 0.12%. Ye [5] investigated dephosphorization of high-phosphorus manganese ore of the Huayuan type. Using high intensity magnetic separation, roasting and leaching with acid for dephosphorization, as used in the industry, a 40.15% manganese concentrate with a P/Mn ratio of 0.0037 was obtained. Yimin [6] investigated magnetic separation followed by inverse flotation of high-phosphorus manganese ore, and found that the P/Mn ratio could be reduced from 0.046 to 0.002."

Jan 1, 2012

By Judy Che, Steven Ceccio, Gretar Tryggvason

"A detailed understanding of drop deformation and solidification is essential for quantitative predictions of geometry and properties of parts made by ballistic particle manufacturing processes. Axisymmetric results of towers built by the deposition of multiple drops are presented. In these computations, fluid flow, heat transfer, and phase change are fully coupled throughout the drop deformation and solidification process. The solution method is based on a single set of conservation equations written for all phases simultaneously. The phase boundaries are treated as imbedded interfaces by adding the appropriate source terms to the conservation equations. A parameter study demonstrates the effect of Weber number, Peclet number, and drop deposition frequency on the final shape of the structure. Numerical results show that most successful method of building uniform towers is when two conditions are met. First, each drop solidifies at the same time in the deformation cycle. Second, the cooling rate is slow enough to allow for good adhesion between drops. The ability to predict the final shape of deposited drops will greatly reduce the amount of experimentation necessary to select the desired set parameters for any artifact.IntroductionMaterial deposition techniques based on layering small molten metal drops holds the promise to build small, coherent three-dimensional structures. In this process, numerous 20-100 µm diameter drops are deposited onto a substrate with a low impact velocity (on the order of 5 mis). Both the momentum and trajectory of each drop are controlled precisely to build up complex parts. This material layering technique differs from processes such as spray forming and splat quenching which involve high impact velocities (on the order of 100 mis) and high frequency deposition with little control over individual drop placement. This process of layering small drops can produce parts with near net shape accuracy, while spray forming produces slabs of material which must then be worked to make a usable part. The ability to computationally predict final drop shape and cooling rate has the advantage of allowing the user to select parameters to produce parts with desired shape and mechanical properties. However, the development of such predictive methods requires a thorough understanding of both drop deformation and solidification"

Jan 1, 1999

By T. R. A. Davey

The technologies of lead, zinc and tin extraction have made varying degrees of progress over the past twenty years. Producers of all metals have faced increasing demands for reduction of pollution and environmental degradation, and the level of public concern is rising rather than abating. New processing techniques must therefore be not only economically feasible, but politically acceptable, even when the demands of "conservationists" and ?environmentalists? are unreasonable. A new generation of processing techniques has come into being, which do not rely on an expensive sintering stage, nor use metallurgical coke, which is difficult to make without serious pollution. They utilise intense reactors, conveying materials from one stage to the next preferably within an enclosed space, obviating fume emissions, and avoiding heat losses as far as possible. The acceptability of the new techniques? is increased if lowgrade or complex materials can be treated, along with a variety of returns and wastes. In addition, a good selling and servicing organisation seems to be as important as good process technology in determining the spread of the new processes. In the field of pyrometallurgical refining the need is for more general application of several recently developed techniques rather than a search for alternatives to the existing process technologies. However, there is a need for fundamental work investigating the phenomenon of oxygen anode overvoltage in the electrolytic zinc process, in order to make progress in the further reduction of energy consumption. There is also scope for further development and application of vacuum distillation to up-grade thermally produced zinc. This paper presents a personal view of processes which should be developed to overcome existing problems, as we approach the turn of the century,

Jan 1, 1990

By Manjie Li, Mingrui Yang, Haijun Peng, Shuxing Qiu, Wei Liu, Shengfu Zhang

It is important to produce and utilize highly reactive coke in order to reduce the energy consumption and CO2 emissions through improving shaft efficiency in blast furnace. The present study aimed to investigate the transformation of iron minerals and properties of iron coke (the coke mixed iron ore fines). Along with the increase of iron ore fines, cold strength displayed a slight downtrend and the pore structure wasn’t inferred to be a major factor affected the properties of iron coke. During carbonization, the majority of mixed iron oxides were reduced to metallic iron by CO and H2 and the degree of metallization achieved to approximately 75%. Nevertheless, produced metallic iron was oxidized by pure CO2 during gasification. Iron coke reactivity index (ICRI) was obviously enhanced and the iron coke strength after reaction (ICSR) drastically decreases, which were also significantly influenced by crystal structure of carbon.

Jan 1, 2015

By Duclerc Fernandes Parra, Washington Luiz Oliani, Christiano Gianesi Bastos Andrade, Ademar Benevolo Lugão, Danilo Marin Fermino, Francisco R. Valenzuela Diaz

This work concerns the study of the effect of discarded bond paper on the mechanical behavior of polypropylene/organophilic clay nanocomposites. A brown polycationic bentonite from the state of Paraíba, Brazil, was treated with sodium carbonate to transform it into a bentonite that swells in water and then treated with hexadecyltrimethylammonium ammonium chloride to transform it into a bentonite that swells in organic liquids. Polypropylene with 3 % polypropylene graft compatibilizer (PP-g-AM) was mixed with 1 % and 2 % by weight of discarded bond paper and with 1% and 2% by weight of organophilic clay using a twin-screw extruder. The specimens were prepared by the injection process. The clay as received and after organophilization was characterized by XRD, SEM, and capacity of swelling in water and in organic solvents. The nanocomposite specimens were characterized by XRD and thermal analysis. The mechanical behavior of the injected specimens was evaluated by strength, flexural and impact tests. The nanocomposites showed improved mechanical properties compared with the polymer without filler.

Jan 1, 2015

By Derek J. Fray

"In order to extend the application of fused salts in\the electrowinning and electrorefining of metals, it is necessary to maximise the current density, minimise the voltage drop and greatly increase the area of electrode surface so as to compete with the space-time yield of pyrometallurgical reactions. The various designs of electrowinning cell are reviewed and it is shown that by the application of a modest centrifugal field it is possible to reduce the anode to cathode interelectrode spacing to 4 mm whilst still maintaining a current efficiency of 85-90%.The thermodynamic potential for electrorefining is far less than for electrowinning yet fused salt electrorefining is only applied in limited cases. The reasons for this are discussed and the important design parameters evaluated. It is concluded that by using packed bed electrodes, separated by a diaphragm, the possibility of electrorefining with very low energy consumption can be achieved. Carbothermically-produced metals are always cheaper than those produced by electrolysis but suffer from the disadvantage of low purity. It is proposed that fused salt electrorefining may offer an energy efficient way of upgrading the metal. IntroductionThe majority of metals can be deposited from fused salts (1,2) but as commercial production is restricted to the more reactive elements, it is worthwhile considering the advantages and disadvantages of fused salt electrolysis as' compared to smelting and aqueous electrolysis. The advantages over aqueous extraction are as follows:1) the much higher conductivities and diffusivities result in much lower IR losses and higher current densities can be achieved at modest voltages;2) the elevated temperatures of operation result in larger exchange currents which give rapid kinetics and lower activation polarisation for the electrode reactions;3) the absence of water as a solvent means that it is not necessary to consider the evolution of hydrogen as a competing cathodic reaction. Furthermore, alkali halide salts, often used as solvents in fused salt electrolytes, have high deposition potentials;4) molten salts generally are mutually soluble and, therefore, concentration polarisation effects are minimised."

Jan 1, 1988

By David B. George

Kennecott recently completed an $880 million modernization and expansion of its smelter and refinery to process all concentrates from the Bingham Canyon mine. This is the first application of Kennecott-Outokumpu Flash Converting. Molten material movement by overhead cranes is eliminated and high levels of oxygen enrichment result in very low process gas volumes and exceptionally control of sulfur oxide emissions. All existing in-plant hygiene, safety, and environmental regulations will be met and the smelter is positioned for anticipated more stringent future regulations. Sulfur capture is 99.9 percent resulting in sulfur dioxide emissions less than the 112 kg/hr Air Permit limit, making the smelter the cleanest in the world.

Jan 1, 1996

By Gunther Schimmel

Ag exudation in four different alloys (Ag-Cd, Ag-Sn, Ag-Sn-In and Ag-Zn) is characterized. The amount of exuded material is correlated with the volume increase due to oxide formation in dependence of the alloy concentration and different densities of the oxide and matrix phases. It is shown that all four alloys show similar amounts of volume increases, but different amounts of exuded material. It is concluded that internal stresses due to the volume increase cannot be the dominant driving force for Ag exudation. A gradient in the chemical potential of Ag that originates from the O concentration gradient inherent to internal oxidation is suggested as driving force. The exudation behavior is thus governed by the variation of the activity of Ag in the Ag fcc phase in the Ag-Me-O system that differs between the alloying systems.

Jan 1, 2010

By Masao Miyake, Eiichiro Matsubara, Tetsuji Hirato, Yasuhiro Awakura

"Zn-Cr alloy coating with around 15 wt% Cr has been found to have much higher chemical corrosion-resistance to steel than conventional zinc plating, while· its structure has not been clarified. The Zn-Cr alloy plating is performed at high current densities around 1 A cm-2 and for 10 to 20 sec using acidic aqueous sulfate solutions with some additives in the iron-steel industry. Due to the high current densities, it seems reasonable to consider that the Zn-Cr alloy plating proceeds under an unsteady-state condition and that the resulting coatings have a non-equilibrium phase and have a structure change in the .direction of thickness. In this research, the crystal structure of the Zn-Cr alloy coating electrodeposited at high current densities and change of the structure in the direction of thickness were examined by X-ray diffraction. The coatings containing under 20 and 35-40 wt% Cr had hcp and bee structure, respectively, while the coatings containing 20-35 wt% Cr comprised two phases with the hcp and the bee structure. The structure of the coating varied in the direction of thickness; both the hcp and bcc phases coexisted in the vicinity of the substrate, while the hcp phase became predominant with increasing distance from the substrate.IntroductionRecently it has been reported that Zn-Cr alloy coating containing around 15 wt% Cr has much higher corrosion-resistance to steel than conventional zinc plating.1-3) The corrosion-resistanc·e of Zn-Cr alloy plated steel sheet with a plating amount of 20 g m·2 is, for example, superior to that of Zn plated steel with a plating amount in the range 60 to 90 g m·2 , which is widely used for automotive bodies today.4l The Zn-Cr alloy plating is obtained by electrodeposition at current densities over 0.5 A cm·2 from a sulfate solution containing zinc and trivalent chromium ions and some additives.5•6) The deposition current densities mentioned above are much higher than those for usual electroplating processes, e.g., Zn, Cu and Ni plating, carried out about 0.05 A cm·2 • Therefore, the time required for plating is very short; around 10-20 sec. Due to the high current densities, it seems reasonable to consider that the· Zn-Cr alloy plating proceeds under an unsteady-state condition and that the resulting coatings do not have a phase expected from equilibrium diagrams; no phase diagram of the Zn-Cr system with a full composition range has been available. 7). In other words, the alloy phase plated would be a non-equilibrium phase with unknown structures."

Jan 1, 2000

By Annette Revet

Aluminum fluxes have been used for the remelting of secondary aluminum since the beginning of the recycling industry. During the last sixty years, a number of fluxes have been designed, researched and tested at the laboratory and plant scale. Fluxes are primarily a mixture of potassium chloride and sodium chloride with the addition of some other chloride and fluoride containing salts. The conventional Mining methods of potassium chloride and sodium chloride yield products that are not high in purity without costly reprocessing or additional refining. In 1993, Kalium Chemicals, Ltd. began supplying flux mixtures to the aluminum industry. Kalium produces potassium chloride and sodium chloride which are mined and refined by a patented solution-mining process. The salts produced by this process are high in purity with lower concentrations of iron oxide, sulfates, and other impurities. This paper will present the different mining methods used in the production of sodium chloride and potassium chloride. The paper Will address how these mining methods affect the purity of the final product as well as the effect of purity on the performance of the fluxing salt.

Jan 1, 1995