Search Documents

The properties of coal or rock containing gas are very important both for studying coal and methane outburst mechanism and for controlling underground rock in mining. The theological fracture properties of coal containing gas were studied to obtain its rheological fracture principle both in microscopic scale and in macroscopic scale. The application of this principle is successful in explaining coal and methane outburst mechanism and for putting forward a rheological hypothesis of coal and methane outburst.

Jan 1, 1992

By Hideki Shimada

A low cost methodology that allows the determination of in- situ stress using oriented core specimens has been investigated. The technique can be used to determine the stresses during the early stages of a project, even in undeveloped areas of a mine. The research aim was to compare the experimental results estimated by the AE and DRA methods to those estimated by conventional ANZI (Australia and New Zealand Inflatable) cell measurements. The studies have been focused on fill stress tensor determination from a single oriented cored rock. In all cases the rock core specimens recollected the in-situ stress reasonably well compared with the standard overcoring method.

Jan 1, 2001

By Zhang Liandong

Roof control in thick-seam mining has long been a difficult problem in mine design and coal mining. In the early 1980's, through ground control instrumentation and investigation the rules of roof strata movement were determined, based on which the sliding roof bar powered support was properly designed and successfully applied to roof control to thick seam mining with caving. Underground trials in Huating Coal Mine produced satisfying results. The technique is being employed in many Chinese coal mines and won the national price for technical advance.

Jan 1, 1990

By Axel Preusse

This paper shows basic considerations about the prognosis and prediction of surface subsidence and other ground movements in the German hardcoal industry. The following case studies describe experiences collected in projects between university and industry.

Jan 1, 2000

By Richard G. Burdick

The Bureau of Mines', Denver Research Center has been conducting research for the past few years on the use of resistivity methods to locate abandoned mine workings. As this work has progressed, it is apparent that in some cases, in addition to detecting the old workings; stoping, precursive to surface subsidence has also been detected. This paper describes the Automated Resistivity method and discusses sites in Colorado. Wyoming. and Illinois where the subsidence phenomenon has been observed.

Jan 1, 1982

By David Bigby

Rock Mechanics Technology has developed an intrinsically safe remote reading telltale system which allows up to 4 sets of 100 dual height, water diverting telltales in a mine roadway to be remotely monitored from a surface PC. The system has US MSHA approval and European ATEX approval for use in gassy mines. A successful full-scale application of the system employing 67 telltales was completed in a 1300m long maingate roadway during retreat of 183.0 longwall panel at West Mine in Germany between June 2001 and October 2002. During panel retreat a number of "teething" problems associated with the system were identified and resolved, the chief problem being associated with cable connection corrosion due to the unforeseen use of sprayed calcium chloride in the roadway. This paper describes the experience of employing the system at the colliery from the perspective of both the user and the manufacturer, and the improvements and developments which have resulted. The paper also presents examples of roof movement data recorded by the system, including data from behind the retreating longwall. The high resolution and data recording rate possible has resulted in particularly interesting information on roof behavior within the longwall front abutment area and behind the face. The paper also describes a series of new transducers and extensometers for the mining industry which employ the same physical principles and similar electronics to the remote reading telltale system. These have been applied in a variety of mining and tunneling environments worldwide over the last two years.

Jan 1, 2003

By Erik Westman

Tomographic imaging, commonly known as a CAT-scan or CT-scan, is used in the medical field to generate a picture of the interior of a body. Current research is applying this method to bodies of rock so that rock failure can be better understood and predicted. This paper discusses the basic principles of tomography and describes recent developments in the use of seismic tomography in longwall coal mines, including results from a bump-prone longwall coal mine and continuing research.

Jan 1, 2003

By Keith D. Koper, Kris L. Pankow, Derrick J. A. Chambers, Michael K. McCarter

"In a mining environment, high quality seismic event catalogs are often useful in interpreting local stress states and identifying areas with elevated ground control risk. Installation, operation, and maintenance of local/in-mine seismic networks, however, may be prohibitively expensive, and mine operators may not anticipate the need for seismic data until unusual mining conditions arise. If regional, generally public, seismic instrumentation could be used to reproduce the results generated by local/in-mine instrumentation to an acceptable degree of fidelity, it would be a valuable and inexpensive tool for mine planners and ground control engineers.In this study we apply subspace detection—a non-traditional seismic event detection technique—to data from a sparse, regional network. The process is employed to identify mining induced seismicity (MIS) from an underground coal district. The results are compared to a seismic event catalog produced by a local seismic array operating within the permit boundaries. Additionally, we analyze the performance of two different stations of the same sparse, regional network in identifying blasts at a surface coal mine for which we have a detailed blasting log. In both cases data from stations between 10 and 60 km away from mining activity are used. We also explore the trade-offs between the number of detections and the number of false positives, which is influenced heavily by detection thresholds and the number of stations used in the process.For the surface mine we are able to identify more than 90% of the production blasts documented in the blasting log. We also find that the detected blasts from each of the four active pits produce waveforms similar to one another. The results are not dependent on source-receiver distance, and by requiring detections to occur on both stations the number of sure false positives is reduced to zero. In the underground mining district we identify between 30% and 75% of the events detected by the local array, depending on the acceptable number of false positives and the source-receiver distance. We also find many events that were missed by the local array, showing that regional subspace detection can usefully augment traditional local catalogs. Moreover, subspace detection can provide an estimate on event location and classification using data from as little as one seismic station."

Jan 1, 2015

By Ben L. Seegmiller

Specially truss systems? including the Intersection Truss®, Continuous Entry Truss®, Cutter Roof Truss® and Roktrus® have been used in many coal mines in the mid- west and western United States during the past four years. These truss systems offer greater strength and support than other standard trusses and many other support devices. Mining operations have found that speciality trusses can give effective long-term support in areas that must remain stable for many years. At some mines, the Intersection Truss® has become the most-widely accepted method of providing secondary support in potential problem areas. Other applications for specialty trusses have included longwall start- up and recovery rooms, arched roofs, access rock tunnels and tailgate entries.

Jan 1, 1990

By Fred Leighton

Outbursts, or the sudden and sometimes catastrophic expulsion of coal and gas into the working area of a coal mine, are a little understood and growing problem. The AE/MS (Acoustic Emission/Microseismic), or rock talk, activity prior to and associated with several outbursts has been recorded using ultrasonic and micro- seismic equipment and has been analyzed by the Bureau of Mines. Analysis of these data indicates that outbursts are comprised of several failures in rapid succession and that anomalous AE/MS data suitable for providing failure warning are generated 15 to 45 minutes prior to the failure. This paper discusses the techniques for recording and analyzing these data and presents sane case histories.

Jan 1, 1982

By Behdeen Oraee-Mirzamani

Since the advent of New Austrian Tunneling Method (NATM), shotcrete as a primary means of support in tunnels has been widely applied. It?s most important features are durability, speed of application and cost effectiveness. This paper introduces some tables that provide guidelines for the thickness of shotcrete required in some common situations of mine roadways. In order to devise such tables, two different arch sections, together with three different overburden types, were considered. Geotechnical parameters such as apparent cohesion and angle of internal friction of surrounding rocks were chosen, based on the five-category classification of Bieniawski. Two K0 factors (the ratio of horizontal stress to vertical stress) and an average rock density were utilized. Using numerical methods, 60 models were then devised in this way. By applying interaction diagrams of axial force and the bending moment for different thicknesses of shotcrete, appropriate shotcrete thickness for these models were calculated. The results of this research, as well as the methodology applied, can be used in mining roadway support design and all types of civil engineering tunnels.

Jan 1, 2011

By William D. Gallant

This paper presents the results of a joint cooperative research project between the CANMET Cape Breton Coal Research Laboratory and the Cape Breton Development Corporation to observe the subsidence profile over the stopline of 2 West panel, Phalen Mine. A novel technique was designed and Implemented to determine vertical displacements of the overlying strata from within a near horizontal borehole drilled over the 2 West panel. Restrictions on data collection techniques due to the submarine nature of the coalfield are discussed. Development and implementation of the borehole technique using a piezometer and inclinometer Is described. Performance of the instruments and profiles obtained by them are presented and compared. Recommendations for design improvements are made to Improve the efficiency of the technique.

Jan 1, 1990

By Ross Seedsman

There are many models for how roof bolts behave, one of which is prevention of shear along bedding. The basis of this model is that a roof beam will not delaminate if bedding parallel shear can be prevented. A key point in such a model is that bedding discontinuities are present naturally in the roof and that mining induced stresses do not generate new surfaces. The presence of these discontinuities means that the rock mass must be modelled as a transversely isotropic material if continuum codes are used. A limit-equilibrium type design method for specifying roof bolts is being developed using voussoir beam and excess shear force concepts. The method incorporates much of what operators know intrinsically about roof reinforcement, and allows mining engineers to focus on the key uncertainty - the frequency and location of bedding surfaces in the immediate roof. Areas where more research is required are highlighted.

Jan 1, 2000

By Clare Offner

In 1998, the Australian Coal Association Research Program (ACARP) awarded funding to the School of Mining Engineering at the University of New South Wales to establish a rockbolt testing facility to research anchorage mechanisms associated with fully encapsulated rock bolts and to develop standardised testing procedures for rockbolts. This facility is still under development but has already been used to evaluate the effect of bolt profile and confinement on the load transfer characteristics of a resin encapsulated rock bolt. This paper describes the test facility and presents some of the results of development testing to date.

Jan 1, 2000

By Steve Signer

Researchers at the National Institute for Occupational Safety and Health (NIOSH) have developed several new tools for evaluating roof support performance. A miniature data acquisition system (MIDAS) was developed that can collect readings from up to 16 strain gauges at regular time intervals and store the readings for later retrieval. Three LED lights change from green to yellow, then red, based on the reading levels and/or rates of change of rock movement. This feature can be used to warn miners of rock instabilities. The system can be used with any strain-gauged support (resin bolt, friction bolt, cable bolt) or with a newly developed rock strain strip (ROSS) developed by NIOSH to measure rock strain. A ROSS is grouted in a hole drilled adjacent to the rock support to be evaluated; the deformed shape of the ROSS provides anchorage on either side of the strain gauges. Data from both laboratory tests and field evaluations are presented that describe the capabilities of both the MIDAS and ROSS instruments.

Jan 1, 2003

By Yoginder Paul Chugh, Jason E. Tinsley

"Over the last five years, the authors have compiled a database of Short Encapsulation Pull Test (SEPT) evaluations from Interior Basin (Basin) coal mines. Typically, SEPT data are analyzed to obtain peak load carrying capacity per unit length of resin encapsulation designated as the ""Grip Factor,"" or GF. In a previous paper, ""An Analysis of Short Encapsulation Bolt Pull Test (SEPT) Data From Interior Basin Coal Mines,"" authors analyzed tangent value of the load-displacement curve as Anchorage Stiffness at 50% (AS-50) of the peak load, or GF value, to assess reinforcement potential of an installed bolt system. This paper attempts to correlate the secant AS VALUES (of SEPT on 6 ft (1.8 m) long installed bolts at a lower load of about four tons from several different mines in the Basin with their MSHA-approved primary support requirements. Since the current regulatory environment requires plan changes dynamically to ensure that roof falls are minimized, the authors hypothesize that the practiced roof control plan must meet the minimum requirement of adequately supporting immediate roof strata. The analyses are based on 181 SEPT studies performed by Minova professionals. Analyses indicate a macrolevel correlation for both roof support density and roof support cost that may have the potential to be used by mine operators to compare their performance with other mines in the area. Limitations of the analyses include ignoring mining depth, mining height and required secondary supports as part of the requirements for a roof control plan. The authors recommend additional analyses to develop this concept further to develop guidelines that can be confidently used by coal companies.INTRODUCTIONPartially- and fully-grouted bolts are extensively used in coal mines for roof support as part of MSHA-approved roof control plans. Since grouted bolts have a larger area of contact with the rock, they can develop much greater anchorage capacity than conventional expansion shell (point-anchored) bolts. Load transfer characteristics and interaction mechanics between steel rebar, grout and rock mass around the bolt hole for grouted bolts are generally assessed in the laboratory or field though short-encapsulation pull tests (SEPT), which have been extensively researched by Aziz and Jalalifar (2005), Aziz (2004a), Serbousek and Signer (1987), Signer (1990), and Mark et al. (2002), among others. In a SEPT, about 12 in. (30 cm) of bolt length is typically encapsulated in resin and a pull test is performed to collect load-displacement data prior to failure and, in some cases, post-failure. A typical load-displacement data set for a bolt is shown in Figure 1. SEPT characteristics are designated by peak load carrying capacity, or grip factor, which is the peak load carrying capacity per unit length of resin encapsulation. SEPT is routinely used to assess anchorage performance characteristics of different lithologies overlying a coal seam to identify type of bolt, bolt diameter, length and spacing across and along an excavation. Anchorage stiffness, or AS, at any load may also be calculated as the tangent or secant value of the slope of the load displacement curve at a particular load level. Anchorage Stiffness characteristics of bolts from SEPT data have typically not been considered in any depth until recently (Chugh et al., 2014; Chugh et al., 2015)."

Jan 1, 2016

By Uros Bajzelj

When driving mine roadways in the vicinity of tectonic disturbances and fault zones, sudden outbursts of gas, along with ejections of fine coal, occur. Substantial dynamic changes occur around the roadways in the coal and around the support. The problem has several aspects. Studies have been carried out on the technical analyses of the phenomena which occurred in the Velenje Lignite Mine from 1957 to 1988, The second part of the investigation involves systematic laboratory studies of strength and deformability characteristics of lignite samples and "in-situ" measurements of stress changes during the driving of some roadways. Analyses of events (using the model of limit convergence and the finite element method) showed the possibility of gas outbursts, taking into account the deformability conditions when crossing over from compact lignite to the disturbed region. The rate of advance of roadways and the method of support strongly influence the occurrence of the phenomenon. The preventative measures used in driving roadways under such conditions include trial drilling and the use of blasting instead of machine cutting.

Jan 1, 1992

By Andrew Starkey

Ground anchorage systems in the form of rock bolts are used extensively throughout the world as supporting devices for civil engineering structures such as bridges and tunnels. It is widely recognized that non-destructive testing methods for ground anchorages need to be developed as a high priority [1 ], with only a small proportion of anchorages currently being monitored in service [2]. The condition monitoring of anchorages is a relatively new area of research, with the objective being a wholly automated or semi-automated condition monitoring system capable of repeatable and accurate diagnosis of faults and anchorage post tension levels. The GRANIT tm system developed by the University of Aberdeen is capable of measuring the integrity of ground anchorages and has won two major UK Awards - the National John Logic Baird Award for Innovation in 1997 and a Design Council Millennium Product Award in 1999. The normal procedure with the GRANIT tm system [3,4] is to train a neural network on dynamic response data that has been sampled from an anchorage over a range of post-tension levels. Further data is needed in order to test the neural network. The paper presents neural networks that have been trained on data taken from a number of anchorages on different sites, and the results of the diagnosis of these neural networks on new test data is presented. The results show that the cross-diagnosis of anchorages is possible, where a neural network trained on one anchorage is capable of successfully diagnosing the post-tension level for an anchorage of similar construction, and the high level of accuracy that can be attained with the GRANIT tm technique is shown. The paper also introduces a mathematical model of the GRANIT tm process.

Jan 1, 2001

By Buddhima Indraratna

The paper highlights the conceptual developments in rock mechanics applied to quantify the effect of bolts in the stabilization of joints and yielding soft rocks.

Jan 1, 1992

By Cao Shenggen

Experiences in the developed countries have shown that continuous increase of panel width (or face length) is one of the major technical trends for high production high efficiency mines. Increasing the panel width will increase not only the panel output, simplify the gateroad layout, facilitate high concentration of production, but also increase resources recovery and facilitate protection of surface structures. This paper uses the No.4326 super- wide panel, Wangzhuang Coal Mine as an example. This mine employs the fully-mechanized top-coal caving longwall mining method. Through surface subsidence monitoring, the dynamic characteristics of surface movement were obtained. The dynamic surface movement during mining and the final surface movement after mining were predicted using the Mining Subsidence Prediction System. The results indicate that after mining, the surface above the super-wide panel reached a state of full subsidence, So it can ensure the No.309 National Highway above is located in the flat bottom of the subsidence basin, and there is little impact on the national highways when panels on both sides of 4326 Panel are mined.

Jan 1, 2003