Search Documents

By Hamid R. Nikraz

This paper reports the finding of a comprehensive investigation carried out to evaluate the compaction characteristics of saturated sandstone aquifers in the Collie Coal Basin under conditions anticipated during dewatering operations. A triaxial technique has been adapted to evaluate the compaction characteristics of the sandstone aquifer in the Collie Basin. This technique, which allows the strata stress regime to be reproduced by triaxial loading with zero lateral strain, also provides a precise evaluation of lateral stresses and consequently Poisson's ratio under in situ conditions. The paper contains a description of the equipment commissioned, test techniques, results, analysis and interpretation of the data obtained. The testing evaluation techniques are general in nature and can be applied to field situations in locations where similar weak sandstones occur.

Jan 1, 1993

By Y. Luo

An extensive subsidence research program conducted by the authors has greatly improved the accuracy and the capabilities of subsidence prediction under complicated mining and surface conditions. The techniques developed for assessing and mitigating subsidence influences on various surface structures have been applied in numerous cases with a very good re- cord of success.

Jan 1, 1997

By B. G. D. Smart

The development of a softwood alternative to the hardwood chockpiece used to build the waste-edge breakers commonly incorporated in gateroad packs is described. The results of laboratory tests on softwood prototypes and two underground trials are presented. The results of the last trial suggest that a viable alternative chockpiece has been designed, offering advantages over availability of wood, weight and given reduced wood content, price.

Jan 1, 1992

By Jinsheng Chen

To maintain the stability of longwall tailgate entries, they have to be supported by not only the primary roof support but also the secondary roof support due to the impact of the longwall mining¬induced abutment loads. Depending on the mining condition of a typical coal seam and its distance from the previous panel's gob, the longwall tailgate entry is often reinforced by the secondary roof support in the form of standing supports and/or cable bolts or trusses during longwall retreat, Even though lots of research work has been done to study the behavior of different standing supports in the laboratory. their function and requirements for a typical mining condition are still not fully understood due to lack of field data and correct assumptions about the behavior of the already-bolted entry roof under mining-induced abutment loads. Therefore, the application of the secondary roof support for tailgate entry roof control is still limited to trial and error, which often results in either higher cost for tailgate roof control if the design is too conservative or more production delays due to roof falls in the outby tailgate entry if the design is inadequate. To have a better tailgate roof control with reasonable roof control cost, RAG American Coal, NIOSH, and HeiTech have been conducting a joint research project to monitor actual roof loading, roof deformation, and entry convergence in the tailgate entry of 10 North panel at RAG Emerald mine. The actual roof loading data are used to calibrate and improve the roof control model for longwall tailgate entries, which has been developed by RAG American Coal, and to further reduce the roof control cost for longwall tailgate entries. The authors in this study attempt to discuss the Roof Control Model developed by RAG American Coal. in which some guidelines or important parameters for designing the secondary roof support for longwall tailgate entries are proposed.

Jan 1, 2003

By Roy H. Grau

The trend in underground room-and-pillar cod mining is to employ remote-control continuous mining machines to take extended cuts of 40 A or more. Roof fall safety hazards to the mine worker associated with 4ed cutting are not completely de6ned but are known to include removal of the miner operator from the protective canopy, non-compliance with approved cutting depth and CM operator positioning. This report summarizes ground control research performed by the National Institute for Occupational Safety and Health (?-JIOSH) researchers at the Pittsburgh Research Laboratory concerning extended cuts. A combination of statistical analysis and underground investigations have been conducted. Statistical analysis of extended cut use, along with roof fall accidents and fatalities data delineate the extent of the problem in U.S. coal mines. Additionally, an underground study is described where the long-term roof stability of extended cut areas are compared to standard cuts.

Jan 1, 1997

By M. Terry Hoch

This paper presents information on low-coal ATRS systems that are now in use. A study was conducted consisting of an in-mine evaluation of ATRS- equipped roof bolters capable of bolting in seams below 42 inches. Machine manufacturers, MSHA personnel, and bolter operators were asked to assist in reviewing the operation of various low- coal ATRS systems. Features of each system are outlined and operational problems and limitations of each are analyzed. Specific applications, such as ATRS-equipped bolters designed for use with auger-type miners, are also examined.

Jan 1, 1988

By D. E. Winston

Roof falls are the major cause of fatalities in the, coal mining industry and the prevention of roof failure is a major concern of mine management. Many ground failures observed underground are associated with geological discontinuities such as fractures, faults, clay veins and sandstone channels inherent in the earth's crust (Rinkenberger, 1977). To properly design a mine requires an advance knowledge of such geologic discontinuities and this is not always available from exploration boreholes. The use of remote sensing for mine planning is a relatively new development, and is at present being used primarily by the Roof Control Support Branches of the Mane Safety and Health Administration (MSHA) in Denver and Pittsburgh. However, technical advances, coupled with public access to previously unavailable photographic products, make remote sensing a useful aid in the difficult process of mine planning (Jansky and McCabe, 1979). Remote sensing techniques are being used to predict the location of geological features in advance of mining which influence roof conditions. The features appear on photographic images as linears, which are plotted on a mine map and serve as a planning tool for mine management. Also, during development of entries toward a linear, mining personnel will be on alert for signs of unstable roof conditions which might normally go undetected. Preventive action can then be taken before a fall occurs. A confusing aspect in remote sensing, analyses is terminology such as linear, lineament, fracture trace and joint. In this report the term "linear" refers to a line-like appearance on an aerial photograph or satellite imagery which signifies a naturally occurring geologic feature no the earth's surface. The objective of this paper is to describe the use of remote sensing techniques as an aid in predicting geological discontinuities which might produce hazardous roof conditions to a mine operating in the Pocahontas No. 4 Seam in southern West Virginia. Mine projections and roof control plans will he developed based on this and other available information such as data from cored drill holes.

Jan 1, 1982

By Tim Ross

Slurry injection into mined-out panels is an attractive alternative for disposal of coal preparation plant fines. however, in areas where surface subsidence cannot be tolerated, either by law or necessity to protect surface structures or aquifers, special consideration trust he given to the effect of slurry injection on panel stability. Slurry injection can lead to panel failure and unplanned subsidence by degrading roof, pillar, and floor strength. Water degradation is of particular concern where clay is present in the floor. Recently. unplanned subsidence related to slurry injection occurred at an Indiana room-and-pillar coal mine subject to weak floor conditions. This paper discusses the efforts of the mine operator to determine the causes of the panel failure and to design panels and injection procedures to allow for future economic slurry injection without subsidence. The numerical and empirical/analytical techniques applied give the operator a rational approach to pillar panel design for future injection panels under various cover depths and weak floor conditions.

Jan 1, 1998

By P. M. Lin

The problem of abandoned mine land (AML) subsidence is getting more severe because abandoned mine lands which used to be located in the remote areas have been gradually developed into suburbs or even urban areas. Abandoned mine subsidence is also becoming more common than before because the time-dependent effect of exposed underground materials. These materials will deteriorate gradually and cause subsidence as time passes. Subsurface conditions of abandoned mines are seldom known to the public. Mine maps are not always available. If the mine mans are available, their accuracy are very - often questionable. In addition, the most common damages to surface structure and ground surface due to mine subsidence can also be created by other non-mining related geological hazards. These factors make the study of abandoned mine subsidence significantly complicated, tedious, and inconclusive. For instance, the cause, time, and amount of surface subsidence can be predicted with relative accuracy during active mining. However, it will be a considerable challenge to do so on abandoned mine subsidence. If abandoned mine subsidence can be predicted in advance, then the damages can be held to a minimum. However, this prediction technique is not yet well developed. Therefore, remedial measures require more attention. In order to have effective remedial measures, the real cause of the damage should be determined first. This paper describes the approach which was employed for the determination of abandoned mine subsidence. A site investigation was made first. According to the information obtained from the site investigation, a hypothesis was set up. Then the instrumentation was used to prove the hypothesis. By going through the procedures for several cases, a guideline which can be used by the inspectors to inspect abandoned mine subsidence will be established.

Jan 1, 1987

By Ed Van Eeckhout

As part of a U.S. Bureau of Mines-sponsored project on the utilization of "stiff' backflll to minimize potential rock burst hazards, a finite element study was undertaken to predict stresses and displacements around a stope mined up from the 5400 level of the Sunshine mine, Kellogg, Idaho. This stope was to be backfilled using a high-modulus fill. In preparation for that configuration, certain instrumentation was installed near the 5400 level to monitor stress changes. Due to untenable economics, only 2 cuts of the stope were ever made. This paper presents the results of the instrument readings taken during the first cut and compares them with the numerical predictions, as well as presents the modeling results of closure and fill stresses in the stope if it had been mined.

Jan 1, 1984

3-D finite element modeling was performed to study the effect of bedding plane sliding and separation and tensioned bolt in layered root It was found that the major influence zones of a tensioned bolt are restricted to the neighborhood of the anchor points; that bedding plane sliding and separation releases the vertical stress in the roof above entry but greatly increases the horizontal stress within the first layer of the roof, and that there is a triangular zone between the two adjacent bolts at and near the roofline level that is beyond the influence zone of the bolts which is liable to fail if conditions exist. Based on the results, three possible modes of roof failure are proposed for the design of tensioned bolting.

Jan 1, 2001

By Vincent Scovazzo

Cost-effective underground mine configurations have been designed in highly fractured rock masses where the stone possesses a high material strength. A limestone mine in the eastern United States is used to demonstrate procedures for the geotechnical design of one such operation. The mine discussed is located in both limbs and the axis of a recumbent fold that fractured the rock mass. In a highly fractured rock mass, where the host rock has high strength, a design can be developed to alleviate intact rock failure. This is possible because in most cases as the stress levels needed for intact failures are approached, the stresses are quickly dissipated due to movement along discontinuities, which represent planes of weakness. As a result most underground failures in highly fractured rock are due to sliding or toppling. Even when intact rock fails in a highly fractured rock mass, it is the movement along an existing joint or other weakness plane that often initiates or causes this failure. It is therefore important to obtain the characteristics of weakness planes that are the discontinuities within the mass. The required information on weakness planes, geology, and strength of materials is discussed and recommendations for obtaining this information are presented. A discussion is provided on failure modes and the use of developed information for their evaluation. The impact on geotechnical design is demonstrated through pillar sizing procedures; however, this approach can also be applied to mine roof and pillar foundations.

Jan 1, 2002

By Nikolaos Polysos

For the planning and driving of gateroads supported by roof bolts a practical concept has been developed in order to determine the geological and rock mechanical parameters derived from exploration drillholes. Based on this, an assessment scheme for the design of roof bolting has been established. The new methods of investigation comprise of geotechnical logging of drill cores for the determination of structural-geological rock characteristics and complementary geophysical well-logging which enables the evaluation of petro-physical and rock mechanical properties. The tools and their measurements will be briefly presented. The relationship between the geophysical log readings and the geotechnical parameters will be illustrated. The aim of the data acquisition is to improve roof bolting design which is based on the assessment scheme. This will be adjusted to the prevailing rock mechanical conditions and stands up to the required stability of the gate roads. In order to ensure consistent data acquisition, a method of core logging has been standardized for the respective demands. To achieve this it was necessary to introduce specific parameters and new methods. For the recording of linear and planar structural elements at the drill core, a special system for the documentation of the angles in relation to each other has been set up. The rock mechanical parameters and their acquisition will be explained. In order to carry out an objective analysis as fast as possible, software has been developed for the acquisition, management and presentation of the data. These programs and their functions will also be presented. The software is characterized by being user-friendly and the flexibility of its interfaces, Different options for the combined presentation of input and evaluated data give a more objective basis for the planning of roof bolt design. Examples will illustrate the operational implementation of the results during the planning and driving phases.

Jan 1, 2001

By Robert L. Schmidt

The support of underground openings by water is a natural phenomenon. Surface sinkholes, such as those that occur with some frequency in Florida, are attributed to a lowering of the water table resulting in the draining of existing limestone cavities. This withdraw the natural support and causes the surface subsidence. The role of water as a ground support medium was demonstrated in a mining situation during Bureau of Mines research on borehole mining of phosphate in St. Johns County, Florida. The borehole mining tool (BHT) incorporates a water jet nozzle and slurry eduotor in a single down- hole tool. The tool is lowered through a bore- hole into the ore zone, and an underground cavity is eroded by the motion of the water jet with the slurry simultaneously pumped to the surface. In addition to phosphate, the system has been successfully used in coal, oil sands, and uranium. The Florida phosphate ore is located at a depth of approximately 250 ft in strata that produce high water inflows. These factors preclude extraction by conventional methods, either surface or underground, but they present an ideal setting for borehole mining. Previous borehole mining research had led the researchers to believe that the system would only be effective in a void cavity, that is, a cavity where the water level is maintained below the water jet nozzle, so that the water does not impede the action of the let. It was soon discovered, however, that the void cavity presented ground control problems. The overlying strata started to cave soon after the support provided by the water was removed. This was an unacceptable situation as it adulterated the ore and threatened surface subsidence. Further tests wherein the size of the cavity -as reduced by cutting only a 30° arc also resulted in caving. A new concept, air shielding, was then introduced and tested. With this system, the water jet cutter was surrounded with a shroud of compressed air, thereby gaining the advantages of cutting in air while retaining the roof support afforded by a water-filled cavity. This arrangement proved to be highly successful. The air-shrouded jet was able to cut a cavity radius of about 18 ft, and the system production was 35 tph, which compared favorably to the production previously attained in void cavities. The borehole phosphate experience proves the efficacy of remote mining in a water filled opening. This system neutralises the hazards of heavy ground, and may, as in the case of the phosphate deposits, be the only viable alternative. It opens up the possibility of application in a wide range of deposits not only those amenable to hydraulic mining. Remote mechanical System might be developed using present robotics technology and then operated in water-filled openings.

Jan 1, 1986

By Daniel W. H. Su

A floor-bearing capacity test apparatus was designed and constructed to determine the true bearing capacity of soft floor materials beneath coal pillars or longwall face supports. The apparatus has been employed in entries up to eleven feet in height. Results of in-mine floor-bearing capacity tests suggested that the ratio of the soft fireclay thickness to the bearing plate width and the moisture content in the fireclay were the most critical parameters affecting the ultimate bearing capacity. Foundation engineering principles were applied to interpret the field test results to estimate the floor-bearing capacity beneath longwall face supports.

Jan 1, 1993

By André Vervoort

In coal room and pillar, and pillar extraction panels, the sidewall conditions were investigated based on underground measurements and numerical simulations. Three-dimensional linear elastic models provided a useful and quick prediction of the amount of sidewall spalling. However, more complex constitutive models were required to simulate more accurately the extent of fracturing and its effect on the stress re-distribution. The input parameters of a Mohr-Coulomb model were determined by back-analysis of underground measurements, and the effect of the depth of the workings and the time dependent occcurrence of coal pillar fracturing were analyzed.

Jan 1, 1992

By Fangting Dong

The broken rock zone (BRZ) and the tunnel support theory are investigated. The relationship between the BRZ and the related factors, the interaction between the BRZ and supports, and the function of supports are analyzed in detail based on the authors' underground observations and model taste. A summary of the application of the BRZ theory in the past is also presented.

Jan 1, 1988

By Richard A. Allwes

A procedure is presented for the design of an arch canopy for the application of rehabilitating a high-roof-fall area. This procedure is specifically developed for evaluating an unbackfllled arch canopy, which Is subjected to an impact load (roof fall). Dynamic line loading of the arch canopy at its crown is only considered and the procedure does not account for an unsymmetrical loading condition. The evaluation of whether an arch canopy is suitable for a particular installation is dependent upon many variables, including in-nine conditions and the engineering properties of the structure. However, a general evaluation can be based upon a comparison of the arch's maximum crown deflection and a prescribed allowable crown deflection. A single spring-mass system is used as an idealized model to represent the dynamic behavior of the arch canopy at its crown. An energy approach is taken to determine the maximum crown deflection of an arch rather than solving a differential equation of notion derived from dynamic equilibrium. The design procedure is based on the concept that when an arch canopy is subjected to impact loading at its crown and deflects from its unloaded state to maximum crown deflection, the structure absorbs strain energy, both elastic and plastic. As a result, this strain energy can be calculated from a static load-displacement diagram for the structure. The significance of this design procedure Is that It gives mine personnel an analytical tool to select an arch canopy to meet the dimensional and functional requirements of a mine entry and a prescribed allowable crown deflection.

Jan 1, 1986

By Hamid Maleki

A novel ground control program has been developed at Plateau Mining Company through five years of geotechnical investigations. The study was initiated to determine the causes for roof stability problems and to develop alternative support and monitoring systems for increased safety and productivity. From systematic roof fall observations, extensive geologic mapping, roof drilling and monitoring ground movements along gate entries of four longwall panels, a sand- stone channel system was detected and shown to impact roof stability. In particular, underlying mudstones up to seven feet thick experienced instability due to differential compaction and load transfer from the gob. Roof bolter operators were trained to report roof lithology for mapping channel positions into the roof and for selective use of longer bolts. This boosted operator morale, and improved ground conditions. Monitoring rates of roof movement is used in these areas for detection of instability and for application of secondary support: This has significantly increased safety and productivity.

Jan 1, 1987

By Craig Collins

The objective was to develop a Real Time Drilling Display System for Rotary Roof Bolting using Analyzing Software to display mapped holes as they are being drilled in real time. The Analyzing Software was developed to analyze and interpret drill sensor data produced during a rotary drilled roof bolt hole by using algorithms and drill sensor data trends to find and locate roof separations or voids. After this software was validated through lab and field testing, its application needed to be tested in a production environment. However, the current method used to record the drill sensor data proved to be cumbersome for the mine to use on a continuous production basis. With different more practical mediums being explored and considered, a Drilling Display System was developed that will both map holes in real time and record the data for later review. With the Analyzing Software's current level of accuracy and with the convenience offered by the real time Drilling Display, the Drill Display System was implemented along with a test mine's current roof control plan and tested as a roof separation "Early Warning System". After installing the Drilling Display System onto a machine, input and suggestions from the mine environment were considered and design changes were made. The real world application provided a design direction that made the information produced by the Analyzing Software both convenient and significant for the test mine. Also, using the Drilling Display System increased the number of drilled holes that were both mapped and recorded. The results from studying these recorded data files lead to refinements in the current algorithms used by the Analyzing Software which increased the overall accuracy and capability of the system A fairly accurate representation of void or separation locations in the mine roof can be determined fromsensor data recorded during production bolting cycle. The immediate feedback on the local roof condition that the Drilling Display System provides, amounts to a quicker and safer alternative to the scratch hole and the video bore-scope examinations that arc performed after the bolting is completed. This project has shown that making the alternative method of examining the roof condition practical for the mine to use is just as important as the accuracy of its results. Based on the results of this field test, this or other methods of reviewing the analyzed drill hole data will be explored.

Jan 1, 2004