Search Documents

By Peter A. Burger

The Greenvale Orebody comprises a series of contiguous lateriteprofiles developed terrace-like during the Cainozoic over a serpentinized harzburgite intrusive emplaced within Proterozoic schists. Each terrace displays individual characteristics of metal distribution. Topographically higher (older) profiles have been partially eroded and metal concentrations reworked. Within the laterite profile, metals have been concentrated or depleted according to their relative solubilities. At tropical temperatures, acidic meteoric waters have progressively depleted the ultrabasic parent rock of Si and Mg, leaving A1 and Fe to form a surface duricrust. Ni, Co, Mn and Cr have accumulated in the lower and middle levels of the weathering mantle. Only Ni and Co have accumulated to exploitable grades. Lateritization has evidently proceeded over a considerable portion of the Cainozoic and may be still continuing.

Jan 1, 1979

By T. Foster

The continuous operation of decanters in the mining industry relies heavily on the use of synthetic flocculants. Today, as plants seek to lower production costs by increasing throughput it is necessary to obtain optimum performance from the flocculant. Factors affecting such optimization include charge and molecular weight selection, and efficiency of mixing the highly viscous polymer solution with the feed slurry. Beyond maximizing dilution of the solution, the last factor is often ignored. This paper describes a series of calculations, based on fundamental transport theories, that have been used to describe flow conditions within decanter feed wells and to help select flocculant addition points. Examples are shown for the case of hydroxamated polyacrylamide flocculants in the Bayer Process, where proper selection of the addition points can result in lower flocculant dosage and better control of the decanters.

Jan 1, 1996

By F. C. Bond

Nature of Empirical Calculations The size reduction of large tonnages of ore and rock is an operation of great magnitude. It is a necessary and important part of industry. Its development has been motivated by practical need and has followed the path of an industrial art without much help from theoretical science. Knowledge has been accumulated from experience. Trial and error established the methods; then collected data were tabulated and served as the basis for empirical equations that have been continually modi¬fied and amplified as new data became available. These equations now constitute the bulk of our present knowledge of comminution. There is no accepted scientific theory that is basic to comminution. In electrical, mechanical, and civil engineering, as well as in many other industrial activities, such theories exist and are extremely help¬ful, but rock is essentially heterogeneous, and the zones of weakness that control its breakage are thoroughly diversified. No theory has yet been discovered which can account for the variability of rock, although many attempts have been made. Empirical equations tell nothing of the why of a phenomenon, but if they are properly derived they can tell much about the how. They always represent only an approximation of behavior but never a law. In a proper empirical equation a symbol is assigned for each of the variable quantities that obviously affect the relationship. In a grinding mill these include mill diameter, mill speed, and feed rate among them. In setting up and revising an empirical equation the cardinal princi¬ple in establishing and modifying it is this: any change must be strictly ascribed to the variable which caused it. A useful empirical equation is rendered useless when a change in any convenient coefficient or exponent is made to make it fit a particular set of data, without certainty that the altered coefficient or exponent is the responsible variable in the new data. Such indiscriminate revisions have brought the use of empirical equations into some disrepute. When existing equations are changed to accommodate new data it is a good rule to make a change which gives results intermediate between the new and the old. A halfway point is usually a good choice.

Jan 1, 1985

By P. C. Clark

This paper is an overview of the requirements and concerns for minerals and pigments used in papermaking. The first part of this paper deals with mineral or pigment filling in the actual papermaking process. The second part deals with the pigment or mineral properties that are important in today's coating processes.

Jan 1, 1993

By Andrew Neale

ERIC GUTIERREZ: With that, we'll go ahead with the final speaker of the day, Andrew Neale. Andrew has a master's of science degree in mineral processing from the University of Alberta. He worked at the Falconbridge in Sudbury area, also at Brenda Mines, and then he became part of the Brenda Process Technology group in British Columbia. He joined Freeport in late 1993 in Indonesia, and was involved in process control and automation. He is now the senior manager of metallurgy in New Orleans. He's responsible for designing Freeport's new 100,000-ton-per-day expansion concentrator, which is currently being commissioned. Please welcome Andrew. ANDREW NEALE: With the ongoing explosion in digital computing power, there seems to be no limit to what can be modeled, simulated, and controlled in the mineral processing plant. However, at each stage of development of a control system, it is necessary to complete a cost-benefit analysis for justifying the move to a higher level of control. Incremental improvements in plant performance, while often significant, must be weighed against the costs of implementation and long-term maintenance. This presentation will provide examples of what the author believes are misplaced or misguided process control efforts and make a case for the KISS principle as applied to process control.

Jan 1, 1998

By Palmer C. Sweet

Mining-related wastes, which are increasing, are being utilized more and more as valuable resources in Virginia. The Environmental Protection Agency (EPA) divides mining-related wastes into two categories: those generated from mineral extraction and beneficiation and those generated from mineral processing. Materials from both categories are produced in Virginia, where waste (by-product) materials are present at a variety of mining sites and processing plants; some of which have been exploited for various uses in the past and/or present. These materials include: used concrete recycled for roadbase material; pyrite coated with magnetite for use in portland cement; minor amounts of fly ash for use in concrete block, lightweight aggregate, and flowable structural fills; granite and diabase quarry fines for use as agricultural and asphalt filler; lime kiln dust for use in neutralizing and stabilizing coal refuse; soapstone aggregate for use in terrazzo heat retention panels; kaolin for use as a filler product and as an ingredient in white cement; slate quarry fines used as landcover and combined with aggregate for crusher run and as a filler in asphalt; and coal refuse for use as fuel in a lightweight aggregate plant. There are some materials available that have never been utilized, although several ideas were investigated to turn them into usable commodities. One such material is a high-alumina scrap produced as a by-product at a ferrovanadium processing plant. However, large quantities of waste materials from metal mining, industrial mineral, and fossil fuel operations remain to be disposed of in an environmentally safe and economic manner. In 1989, almost one million tons of fly ash were produced from burning of coal at eight coal-fired power plants in Virginia. Present uses for this waste such as an ingredient in concrete block, concrete aggregate, and in structural fills cannot dispose of all the available material; however, increased use of fly ash as a soil/rock substitute for structural fills and embankments may solve the problem of its disposal. Another waste material is calcium carbonate precipitate paste produced at a lithium carbonate processing plant and presently being used for back filling an on-site inactive underground limestone mine. Flue gas desulfurization (FGD) wastes in the form of CaS04 will probably increase threefold. If this material contains a minimum of 95 percent gypsum and negligible chloride, it may have a value to a wallboard manufacturer as we move toward the year 2000. Thought must be given how this increasing waste can be disposed of in an environmentally safe manner.

Jan 1, 1995

By S. Chander

The effect of pretreatment potential on the response of a gold electrode for Eh measurements in sulfide solutions was examined in terms of measured Eh values and electrode response time. The electrode response time is defined as the time required for the electrode to reach a steady-state value. The relationship between measured Eh values and the hydrosulfide ion concentration is established. The effect of pH, the reversibility of the gold electrode in the sulfide solutions, and the reproducibility of measurements are also investigated. A mixed potential theory is proposed to explain the observations.

Jan 1, 1989

By Jim Dunn

For decades many of us who are associated with the mineral industry have tried to show the public its economic and strategic importance. Some of the mineral industry's proponents have been politically powerful figures and have been widely quoted. Yet, as measured by public opinion, legislative support, or almost any other standard, our efforts have been inadequate. It is apparent that a set of environmental beliefs that discredit industry, firmly held by a number of idealistic persons, has had wider coverage in the media and in schools than has the mineral industry's message. Although the fervor of our idealistic friends is often unfounded and, their stands unscientific, they must be considered seriously. Unless we address the issues in terms the idealists will understand, the mineral industry will have little influence on them or on the general public. A. striking thing is that, quite often, translation of idealists' views into action has been counterproductive. The reason is obvious. Excessive amounts of money and energy have been spent on relatively minor problems. The common result is that larger problems have been created. It may be possible to help anti-industry idealists understand their own dependence on minerals, and thus render their views more realistic, if they are shown more effective ways to reach their stated goals. If those goals can be shown to be held in common by all sensitive human beings -- including those in business and industry - the dialogue becomes one of how to achieve common ends. Individual mining companies acting by themselves have little possibility of success, and companies working in unison through trade associations have not been successful. Further, it is unlikely that industry in general can be successful in changing minds unless it seeks outside help. But friends among those who influence public opinion have been hard to find. Historically, help from media has proven difficult to get. Nor has enough help from educators been forthcoming. Yet, a war is going on in the technological, philosophical, and political trenches, even though much of the public is not aware of it. For the first time in years, there is row a significant and growing number of eloquent and brilliant thinkers on the side of free enterprise and industry, many of them environmentalists, but without the anti-industry mind-set. They have had remarkably little help from the private sector or even from the present administration. Industry may do far more for itself in the long run by encouraging these brave but bruised individuals and their organizations than by trying to work alone. These friends of free enterprise are working against a seemingly stacked deck relative to much of the media, the bureaucracy, and the educational system. However, despite their problems, their success to date has been remarkable. With more cooperation from industry they should do even better.

Jan 1, 1987

By R. N. Chakravorty

It is well established that coal can react with oxygen in air at ambient temperature and as a result heat is produced. If the heat is not fully dissipated the temperature of the coal mass will increase, thereby enhancing the rate of oxidation with a greater production of heat. If this phenomena continues, the coal mass can ignite under favourable heat accumulation conditions. A number of mine fires are caused each year due to this phenomena, commonly known as spontaneous combustion. The early detection of spontaneous combustion is of prime importance to mining engineers since any fire which could be detected at an early stage may save the mine from considerable damage and subsequent loss of production. Obviously, there is no single general criteria by which one can assess whether the under- ground mining of a coal seam will result in liability to spontaneous combustion. This has made it imperative to develop systems for the early detection of heating and to follow its development. In recent years considerable advances have been made in the design and development of methods for the early detection of spontaneous combustion. The Mining Research Laboratories (CANMET) is presently investigating the problem of spontaneous combustion in coal mines with Kaiser Resources Ltd. at their hydraulic mine at Sparwood, B.C. on a co-operative basis, and some of the work was described earlier in the Canadian Institute of Mining & Metallurgy Bulletin (1,Z). This paper summarizes and updates the work done by CANMET on the detection of spontaneous combustion in coal mines.

Jan 1, 1980

By Robert Blair, David L. Fey, Stanley E. Church

Determination of the pre-mining geochemical baseline in bed sediments in watersheds impacted by historical mining activity is important in establishing watershed restoration goals. We have developed methods to solve this problem in the Animas River watershed, southwestern Colorado, using geomorphologic mapping to identify terraces that contain pre-mining sediments. Following a systematic evaluation of possible sites, we collected samples of pre-mining sediments in gravel deposits from 21 sites throughout the watershed. Geochemical analysis of individual layers has produced a chemical stratigraphy that can be tied to the historical record through geochronological and dendochronological studies. Analysis of geochemical data, when coupled with the historical record, clearly shows that there has been a major impact on the geochemistry in bed sediments in the active stream channel by past mining activities. Historical mining has resulted in a substantial increase in metals in the very fine sand to clay-sized component of the bed sediment of the upper Animas River, and Cement and Mineral Creeks, which are the major tributaries of the Animas River. Enrichment factors for metals in modem bed sediments, relative to the pre-mining sediments, range from 1 to 6 for arsenic, 1 to more than 10 for cadmium, 1 to about 15 for copper, 1 to more than 25 for lead, 1 to more than 10 for silver, and 1.6 to more than 12 for zinc. The pre-mining bed sediment geochemical baseline is high relative to average crustal abundance values of many metals. The Animas River watershed above Silverton, Colorado would be readily identified as a highly mineralized area suitable for mineral exploration if it were not disturbed by mining.

Jan 1, 2000

By D. Hodouin

The optimisation of mineral processing plants requires the evaluation of performance indices such as production rate, product quality, valuable mineral recovery and process efficiency. Decision to change operating conditions or equipment to improve plant performances rely on the significancy of the estimated performance indices. The better is the quality of the estimation, the better is the discrimination capability of the index and as a consequence the larger is the operation improvement. The reliability of performance calculation depends on the sensors nature, accuracy and location, on the data redundancy, on the correction method applied to raw data and finally on the propagation of measurement errors along the calculation of performance indices. To maximize the quality of the data collected for performance evaluation, the following techniques are presented, discussed and illustrated: redundancy and observability analysis, data filtering for mass conservation, variance analysis of performance calculation, and data acquisition strategy design.

Jan 1, 1991

By S. Fairis Samuelson

Boling Dome. a piercement salt dome in the Texas Gulf Coast basin is (was) the single largest deposit of native sulfur in the Western world. Total sulfur production has been over 81.000,000 long tons and the mine is still in production. Data from over 60 years of operation and 8.000+ wells reveal a salt dome rich in history as well as minerals. Sulfur mineralization and production correlate well with caprock structure and morphology. The occurrence of Mississippi Valley-type deposits in fracture zones is notable in some areas and may warrant additional study. DISCOVERY AND PRODUCTION HISTORY Boling Dome is located in the south- east corner of Wharton County, Texas, 60 miles south-west of Houston. It is a piercement type dome in the Houston diapir province. It was discovered in 1922 when the county surveyor noticed sour gas seeps along the San Bernard River (Haynes. 1942). Several companies including Gulf Production Company. Humble, Texas Company, Sun and others quickly began drilling for oil and gas. Traces of native sulfur were reported in cuttings from many wells penetrating the caprock, but the first commercial quantities of sulfur were not found until Gulf Production's E.M. Chase 3 and 4 wells were drilled in 1927. Texas Gulf Sulphur, then mining sulfur at Gulf Dome in Matagorda County, secured the sulfur rights from Gulf for $3 million in cash and half of the profits after expenses for development and construction of plant and townsite were met (Haynes, 1942). The drilling results from 200 or so Wells revealed a massive deposit destined to become the largest single source of native sulfur in North America. Original reserves were estimated at just over 46 million long tons and were increased in later years. Production by the Frasch method was begun by Union Sulphur in 1928, and continued by Texas Gulf Sulphur Co. in 1929, and Duval Sulphur Co. and the Baker Williams Co. in 1935. Union produced 8,009 long tons, Duval produced 571,123 long tons, and Baker Williams produced 1,453 long tons. Through its deal with Gulf, Texasgulf acquired the largest and best mineralized portion of the dome and has produced 88,544,466 long tons through 1990, and production is planned for several more years. That amount of sulfur is equivalent to a cube measuring 1,152 feet on each side, or a sulfur highway 1 foot thick, 20 feet wide and 14,479 miles long. Peak production averaged 8,376 ltpd in 1948. A price war between North American sulfur producers and Mexican sulfur producers in 1956, followed by the recession of 1957 and 1958 (Haynes, 1959) coupled with a rapid increase in mining depth to below 700 feet began a gradual production decline that was never reversed (Figures 1 and 2).

Jan 1, 1992

By T. D. Murphy

In the fall of 1988 it became evident that the accuracy of sulfur forecasts for Monterey Coal's No.1 Mine needed to be improved. In addition, it became necessary to predict if any individual train shipments during a month would exceed a contract sulfur limit. The challenge was to develop a forecasting process that would take into account the variability of the coal in the ground as well as the difference between laboratory and preparation plant sulfur reduction efficiency, and the effects of mining coal with multiple units. This paper describes how geostatistics and simulation techniques were used to meet this challenge.

Jan 1, 1992

By L. Figueroa

Electrochemical methods have potential to treat waters impacted by mining, while simultaneously producing a recoverable metal product to off-set treatment costs. Mining-impacted waters may present challenges with electrochemical treatment due to low concentrations and complex solutions of numerous dissolved metals. This paper presents an evaluation of the potential strengths and limitations of abiotic electrowinning of mining-impacted waters. In particular the impacts of chemical composition on metals removal are evaluated. Results of bench-scale experiments demonstrate the potential to remove metals on the cathode (copper, cadmium, lead), as well as the anode (manganese). Pre-treatment for iron and aluminum may be needed and post-treatment pH adjustment would be necessary. INTRODUCTION Due to continually increasing demand for metals, new technologies and innovative applications of existing technologies are needed to recover metals from mining-impacted waters. Electrochemical methods have long been used for metallurgical processes with solutions containing high concentrations of the target metal. However, electrochemistry also has potential to treat waters with lower metal concentrations, while simultaneously producing a recoverable metal product to offset treatment costs. Electrochemical water treatment may have several benefits over traditional alkaline treatment for acid rock drainage (ARD). Sludge produced from alkaline treatment has high water content that is difficult to dewater, even for treatment plants producing a relatively high-density sludge. For example, the Argo Tunnel Water Treatment Facility (Argo Facility) in Idaho Springs, Colorado uses hydrated lime to produce a high-density sludge with a solids content of 20 to 25 percent and filter cake with solids content from 30 to 35 percent [1]. Furthermore, costs for managing the sludge are significant, approximately $90,000 per year for treating approximately 150 million gallons of water [1]. Although not the case for the Argo Facility, sludge produced from alkaline treatment of ARD has potential to be classified as hazardous. Disposal of sludge also opens up the potential for future liability depending on the sludge’s chemical stability and methods of disposal. In contrast to alkaline treatment, electrochemical treatment produces metals in elemental and other highly-dense forms on the cathode. If metals concentrations and flow rates are sufficiently high, the metals recovered may help offset overall treatment costs. In addition, sludge production would be reduced, if not eliminated altogether, thereby reducing both disposal costs and potential future liabilities as well.

Jan 1, 2019

By Robert C. Cifelli

INTRODUCTION Background and Objectives Underground coal mining is a vital component of West Virginia's economy. However adverse environmental effects including ground subsidence and aquifer dewatering are often associated with such mining activities. Many families in northern West Virginia still rely on private water wells and springs for domestic water needs. In such areas where underground coal extraction and land subsidence have occurred, a disruption of the ground water flow system commonly exists with subsequent drainage of water to lower levels that may extent as deep as the mine workings; this causes loss of water supplies to landowners and represents a nuisance to mining companies 2 This report represents a summary of an M. S. thesis project in geology at West Virginia University by the senior author (3). The intent for this study was to document the effects of underground coal removal on ground water levels at selected mine sites in northern West Virginia, as observed from water wells, springs, and streams. This research should be useful to coal companies and regulatory agencies and aid in recommendations of future water well locations and specifications in areas of existing or proposed underground coal mines.

Jan 1, 1986

By Robert J. Gorney

This paper deals with the actual application of a direct digital control to simple as well as complex industrial process control loops, Fundamental descriptions of preliminary research and design are described briefly, as is the development of the present day controller and control computer. The results and effects of direct digital control in various types of single and cascaded loops as opposed to the use of conventional controls are discussed. Computer supervision of a process and control override are taken into account, in addition to methods of short and long term plant economic optimization.

Jan 1, 1965

By Patrick J. Ryan, Johann F. Kerl, Angelos N. Findikakis

Introduction Tailings disposal methods used by the mining industry include the use of on-land impoundments, surface and underground mine backfill and marine disposal. The latter method, where applicable and under certain circumstances, can be the most economical and best environmental option. The term marine disposal is used to describe deposition of tailings in the open ocean, coastal waters, fjords and inland lakes. A major element in planning and designing a marine outfall is the assessment of its potential environmental impacts. The nature of the disposed tailings, and the physical, chemical, and biological characteristics of the receiving water body must be carefully assessed prior to deciding whether marine disposal is an acceptable option for a particular project. During the last decade, the North American mining industry has demonstrated a commitment to studying potential adverse environmental impacts of marine tailings disposal and to continue monitoring of the receiving waters. Extensive monitoring programs have been undertaken by Canadian mines. Marine tailings disposal is not used in the United States today. One of the largest U.S. mines proposing to use this option is the Quartz Hill mine of U.S. Borax in Southeastern Alaska. To assure the regulatory agencies and the public of the viability and acceptability of this option, U.S. Borax undertook an extensive program of environmental studies aimed at assessing the impact of marine tailings disposal. This program was part of the feasibility and environmental permitting studies conducted by Bechtel Civil & Minerals, Inc, on behalf of U.S. Borax. Due to the unique nature of the proposed tailings disposal system, a Board of Consultants was established. The Board assisted in planning the modeling and field program and reviewed ongoing work. This paper outlines the basic elements of the marine tailings disposal study program which can be viewed as a prototype for similar studies elsewhere. Background The Quartz Hill molybdenum deposit is located on a knoll in an elevated valley in a mountainous region of southeast Alaska, about 45 miles east of Ketchikan (Figure 1).

Jan 1, 1986

By K. H. McDaniel, D. M. Loring

The underground ventilation system at the Waste Isolation Pilot Plant (WIPP) provides for the unparalleled ability to ensure the safety of the workers, the public and the environment. Although small spatially, the system can vary the airflow from 31.2 to 217.1 m3/s (66,000 to 460,000 cfm). The system can automatically incorporate HEPA filtration in the event of radioactive contamination. Remote-capable regulators individually control the four main splits, and they can be adjusted from the surface if necessary. A ventilation remote-monitoring and control system provides real-time information. Future areas of concern include DPM compliance, system psychrometry, logic-based real-time mine-ventilation simulation and automation using PLC technology. This paper discusses the evolution of this system.

Jan 1, 2003

By K. H. McDaniel

An interactive mine ventilation simulation software program (WIPPVENT) was developed at the Waste Isolation Pilot Plant (WIPP). The WIPP is a U.S. Department of Energy (DOE) research and development project located near Carlsbad, New Mexico. The facility is designed to provide a permanent, safe underground disposal of U.S. defense generated transuranic waste in bedded salt. In addition to its regular functions, the underground ventilation system is engineered to prevent the uncontrolled spread of radioactive materials in the unlikely event of a release. To enhance the operability system, Westinghouse Electric Corporation has developed an interactive mine ventilation simulation software program (WIPPVENT). While WIPPVENT includes most of the functions of the commercially available simulation program VNETPC (copyright © 1991 Mine Ventilation Services, Inc.), the user interface has been completely rewritten as a Windows ® application and screen graphics have been added. WIPPVENT is designed to interact with the WIPP ventilation monitoring systems through the site wide Central Monitoring System.

Jan 1, 1996

By D. R. Zeni

Current mine development requires the safe, 'expedient, economical construction of vertical shafts for ventilation and access in diverse ground conditions. Advancements in large diameter shaft drilling have lead to exceptional mechanical refinements of shaft drilling technology. The author traces the history of the equipment and methods employed by the large diameter shaft drilling industry and explores likely paths of future development. A few case histories are cited to illustrate the adaptability of shaft drilling as a versatile tool for advanced worldwide mining operations. Safety, schedules, cost, environmental impact, and capability are discussed to assist the mining engineer in the investigation of feasible projects.

Jan 1, 1994