Search Documents

By C. V. Deutsch, O. Babak

A longstanding problem in geostatistics is that kriging usually assigns significantly greater weights to end samples in strings of data than it does to central samples. These weights are theoretically valid, but suboptimal estimates may result when there are geological trends in the variable near contacts, that is, large weights may be applied to samples that are systematically lower or higher than average. A number of ad-hoc corrections exist, each with pros and cons; none are fully automatic with a well-defined measure of optimality. A new method for estimation in a finite domain is proposed. This method is referred to as finite domain kriging. The method is based on kriging with a successively larger number of data. The total number of relevant data (n) is established, and then n kriging matrices are solved. The first matrix has the closest single data value (n-1 weights are set to zero); the second has the two closest data (n-2 weights are set to zero) and so on. The final matrix has all n data. The kriging weights used for estimation are the average of the weights from the n successive kriging runs. Each kriging run is optimal, yet with different smoothing and a different treatment of data at the end of the strings. The result is a set of weights that does not give undue influence to data values at the end of strings. The methodology is developed with examples. Cross validation shows that finite domain kriging outperforms conventional kriging.

Jan 1, 2009

By K. N. Han

A kinetic model for the batch leaching of various metals using different lixiviants was developed. The overall material balances for the reactants and products at the solid/ liquid interface were formulated for various types of heterogeneous reactions at the interface. The solutions to these mass balances are identified analytically, as well as numerically. Applications of these numerical solutions to various leaching systems using rotating discs or powders are discussed. The metal-dissolution systems addressed include cobalt, nickel and copper in acid, cyanide and ammoniacal solutions.

Jan 1, 1996

By W. Lorenz

The responsible treatment of natural resources, including mineral raw materials, contributes to the protection of the environment. The management of resources and the environment encompasses reduction of emission through application of environmentally friendly processes, economical use of resources, recycling and substitution, application of energy saving processes, land reclamation and recultivation, as well as a well balanced regional and land use planning. A variety of materials are needed for measures to protect the environment. Many of these materials are, or to a large percentage consist of, mineral raw materials, which become effective either directly or indirectly in their natural state or after an appropriate industrial treatment. We call them environmental minerals. Although extraction and processing of these mineral raw materials destined for use in the protection of the environment, may have a negative impact on the environment on one hand, preventive or curing measures to protect the environment on the other would not be possible without them. We have to accept certain smaller burdens of the environment, which naturally will have to be kept at the lowest possible level, in order to avoid or minimize greater damages to nature. In the broad group of industrial minerals and rocks there is a wide variety of mineral raw materials, which lend themselves for countermeasures in favor of the environment. To hamper their production and processing through excessive environmental regulations would make the protection of the very environment more difficult or even impossible.

Jan 1, 1995

By T. C. Page, P. C. Gibson, M. A. Miller, J. D. Sell

[The Yarnell gold deposit in the Weaver mining district, Yavapai County, Arizona, occurs in a structurally controlled, hydrothermally altered zone in a 1700 Ma granodioritic intrusive. Both potassic and sericitically altered rocks around and above the low-angle, northeast striking Yarnell fault are known to host economic gold mineralization. A wider envelope of weakly-propylitic altered rock also occurs in this area. During mineralization, strong sericitization accompanied several stages of quartz (±adularia) veining, stockwork formation, localized silicification and potassic replacement, in association with deposition of specularite, pyrite (now oxidized) and gold. The footwall of the fault is also sericitically altered but poorly mineralized. Mineralization along the Yarnell fault continues both northeast and southwest from the main deposit, although the thickness of the zone and associated alter avian envelope diminish away from the orebody A sample of undo formed illite taken from the Yarnell fault zone was K/Ar dated at 69 + 1.6 Ma. This date reflects a minimum age for both mineralization and latest movement on the fault. Gold mineralization is accompanied by modest increases in Ag, As. Cu and Mo content. Both CO2- and H2O- rich fluid inclusions were studied and suggest mesothermal pressures and temperatures of formation for the deposit. Ninety-six reverse circulation holes and four diamond drill holes outline a bulk-minable mineral reserve of'4.1 million tons at 0.051 oz of Au per ton. An additional 2.7 million tons at 0.017 oz of Au per ton occurs in a low-grade zone above and subparallel to the main mineralized zone. Total calculated mineral inventory stands at 6.8 million tons at a grade of 0.038 oz of Au per ton, with a waste-to-ore ratio of 1.45:1. Column leach tests indicate that cyanide heap leach gold recoveries should exceed 70%.]

Jan 1, 1994

By E. K. H. Goh

A reliability-based engineering design approach for the effective design of reshaped spoil dumps was developed with the aim of obtaining structurally reliable spoil dumps at optimum reshaping costs. The aim was also to satisfy environmental erosion standards and community expectations. This approach encompasses the linking up of three major components: erosion appraisal of spoil dump designs, reliability-based engineering design of spoil dumps and costing of spoil dump reshaping practices. This paper addresses the application of the reliability-based engineering- design approach to the assessment of spoil dump designs for erosion control. Included are various types of erosion prediction models and reliability-based engineering-design analytical techniques. Also included is a case study that demonstrates the application of this approach.

Jan 1, 2000

By Parris A. Lyew-Ayee

This paper is the first preliminary report on the bauxites and terra rossas of the Caribbean. It concentrates on the islands of the Greater Antilles, and for reference purposes the Yucatan Penin- sula is included. At this point, observations made in Jamaica, Haiti, and the Dominican Republic are compared with reported information on Puerto Rico, the Bahamas, Cuba, the Cayman Islands, and the Yucatan Peninsula with regard to occurrence, as well as physical, chemical, and mineralogical composition. From this, an attempt is made at classifying the types of bauxites in the Caribbean, indicating the best reserves estimates, and the process ability of these bauxites. Some suggestions are also provided to fuel the controversy over the likely source material(s) or origin of the Caribbean bauxites.

Jan 1, 1984

By Konstantinos Komnitsas, Evangelos Petrakis, Emmanouil Varouchakis

The paper discusses the limitations of population balance modeling (PBM) in predicting particle size distribution in grinding systems. It introduces a nonlinear framework that transforms the batch grinding equation into the Rosin-Rammler distribution, providing more accurate analysis under different operating conditions. The study uses marble as test material and investigates the adaptability of the nonlinear model with different media sizes.

Oct 1, 2023

By Kevin D. Lofftus

This paper presents a dynamic model for column flotation. The model equations are normalized and the dimensionless groups that are directly responsible in determining the column flotation behavior are identified. The resulting model equations are incorporated for computer simulation. Numerical results from computer simulations are analyzed to gather information about design and operation of column flotation devices.

Jan 1, 1988

By Gary A. Kordosky, R. Brantley Sudderth

The solvent extraction process as it applies to the recovery of metals from solutions on a comnercial basis is described. The four types of classes of sol vent extraction reagents are explained: 1) solvation, 2) acidic, 3) ion-pair, and 4) chelation, and examples of each type of reagent system are given. The uranium and copper extraction examples, using the ion-pair and the chelate reagent types respectively, are presented in greater detail to illustrate the more subtle aspects of reagent evaluation and selection. Practical experiences in the laboratory and at some operating plants are a1 so discussed.

Jan 1, 1986

By Brian P. Stapleton, Bill M. Stewart, Joel R. Warneke, Curtis C. Clark

Of the 28 accident/injury classifications listed by the Mine Safety and Health Administration, handling materials is second only to roof falls in terms of generating the highest number of reportable accidents in active underground coal mines. Two materials-handling activities that cause numerous injuries each year are the categories of ‘handling supplies or material, load and unload’ and ‘moving power cables.’ Mechanization and mine worker activity training are two methods that can aid in preventing these injuries. This paper describes three mechanical methods – the mobile manipulator, the in-mine hoist, and a cable-handling system - being developed and tested at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Two of the devices are specifically designed for loading, unloading, and moving supplies and materials, and the third device is for handling trailing cables in the confined spaces of coal mines. Also described are safety solutions developed for underground coal mines geared to showing miners safe and unsafe ways of performing various materials-handling tasks.

Jan 1, 2005

By Andrew T. MacKenzie, Paul A. Rantala

Predictive pastefill rheology (flow characteristic), models have long challenged pastefill practitioners. While the methodology and practicality of recipe formulation is attainable in most locals, the remaining challenge has been to devise a predictive mathematical or empirical model of paste flow characteristics. Flow phenomenon can now be assigned mathematical and physical basis. The authors herein disclose physical and mathematical methods that demonstrate how operators could proceed when designing reliable pastefill systems. Knowledge presented will allow users flexibility in adjusting flow-rates. Laboratory data shows stiff pastefill delivery design can be derived through mathematical relationships of particle size, material characteristics and pipe diameter.

Jan 1, 2001

By S. Chander, A. Briceno

The effect of sample storage in argon and in air on the kinetics of oxidation of pyrite from a coal source was studied using accelerated-weathering tests that were performed in laboratory columns. Prior to the weathering tests, the samples were crushed, ground and stored for various periods of time in either argon or air. The test results showed a dramatic difference in the rate of oxidation of the aged samples. The interpretation of the differences was based on the hypothesis that the aging of pyrite led to the formation of surface coatings that changed with time. "Dry" oxidation produced surface coatings that had properties different from those produced by "wet" oxidation. The significance of these results to pyrite/reagent interactions during flotation and in evaluating the acid-mine-drainage potential of pyritic waste materials is discussed.

Jan 1, 1995

By Sean Gallagher, Thomas G. Bobick, Richard L. Unger

This paper describes research by the Bureau of Mines on alternative materials-handling strategies for reducing the costs and incidence of back injuries in low-seam coal mines. Strategies recommended for redesigning materials-handling tasks include elimination of tasks, mechanization of tasks, and matching lifting tasks to the physical capabilities of underground miners. The report also discusses other methods that can be used by management to reduce the costs associated with back injuries. More detail can be found in Bureau of Mines Information Circular 9235 (Gallagher et al. 1990).

Jan 1, 1992

By Thomas V. Durkin

About 1.41 kt (45.2 million oz) of gold have been ! produced in South Dakota since 1875. South Dakota's mining laws attempt to strike a balance between economic development and environmental protection. Mining is promoted as an industry while prevention of pollution is required along with reclamation of affected lands to a beneficial use. The South Dakota Department of Environment and Natural Resources' (DENR) system of "one-stop shop- ping" for environmental permits streamlines the permit process. It fosters quick resolutions to compliance problems and helps keep enforcement actions out of the courts. Paha Sapa means "Hills that are Black" in Dakota Sioux. Appearing dark from a distance due to a thick forest of Ponderosa pine, the Black Hills were gold to many people. The exact date that gold was discovered in the Black Hills remains debatable. An inscribed stone tablet found in 1887 near Spearfish recorded these words:

Jan 1, 1998

By Graham Swan, Richard K. Brummer

The paper begins by describing an underhand cut-and-fill mining concept for a 50m thick, generally tabular though irregularly shaped orebody dipping at 30 degrees and occurring at a depth of between 2300 and 2700m in the Sudbury Basin. From this, the broad design requirements of a fill system are stated. Two and three-dimensional numerical models are then described which were built to evaluate the theoretical benefits of different types of fill reinforcement. Included in this evaluation are the effects of span, fill strength, fill tightness, as well as static and dynamic loading types. Results, supported by large-scale physical models, are presented to show the significance of reinforcement on stable, undermined fill performance. Finally the paper describes work which has been done to evaluate the suitability of so-called silicated cemented backfill. This system is, in principal, attractive for deep mining applications since transportation is in the "safe" hydraulic regime, while fill water run-off, segregation and shrinkage effects are potentially eliminated in the stopes. The results from various surface and underground trial pours are reported which substantiate the proposed use of this type of backfill at depth.

Jan 1, 2001

By D. M. Richards, A. D. MacPhail

Highland Valley Copper currently mines two low-grade ore bodies, Lornex and Valley. The partnership was formed in 1986. As a cost reduction measure, it was decided to use an in-pit crushing and conveying system to deliver the ore from the Valley Pit to the Lornex mill 3 km (1.8 miles) away and 175 m (575 ft) above the pit rim. The system uses two gyratory crushers that feed a series of conveyors to transport up to 130 kt/d (143,000 stpd) to the main stockpiles. This paper describes the performance of the in-pit crushing system as it is currently configured, as well as its evolution to date and future planned moves.

Jan 1, 1995

Many of the deeper ore reserves in current gold operations as well as new gold deposits consist of refractory ore types. As process development for these mineralizations remains time-consuming and costly, minimization of exploratory testwork and the early identification of feasible process routes is critical. Since most of the processing parameters are related to the mineralogy of the ore (Marsden & House, 1992), thorough mineralogical analyses during exploration and development phases have become a technical and economical requirement. The determination of mineralogy-related processing parameters and especially the gold mineralogy is even more important for these ore types because refractory gold ores consist of many transitions from partially leachable to totally refractory. In addition to sulfide and gangue encapsulation, various other refractory conditions may exist. Together with accessory mineralogical detriments (e.g., alteration/ slimes, reagent consumers, scale formation, mineral preg robbing) they may complicate process selection and hamper optimal plant operation.

Jan 1, 1993

By P. James, L. J. Steiner, F. Turin

NIOSH researchers and an industry partner conducted an investigation to study the effectiveness of ergonomic interventions in mining. The study required a significant commitment of time and resources from the cooperating site, Bridger Coal Company. This paper focuses on some of the challenges faced by the researchers and their cooperator. Challenges included the need to redesign methods of identifying and prioritizing injuries, and the need to train the workforce in ergonomics while still maintaining progress and interest in the process. The authors discuss some practical interventions implemented by Bridger Coal to date, and discuss future research implications brought about by PacifiCorp’s Generation Business Unit, who monitored the project to determine whether an employee-owned ergonomic process could be implemented throughout their operations.

Jan 1, 2003

By Sunil Jain, Jan M. Mutmansky

As coal mining evolves in this country, underground coal is being mined at greater depth and under more difficult conditions than in the past. At the same time, economic conditions make it necessary to mine more efficiently and economically. As a result, pressures on mining companies arise on two fronts and make the job of mining coal underground very difficult. Recent improvements that have been made in health, safety and productivity have come about primarily due to improvements in existing technology and better management of all the production resources. However, this trend can continue only so far and thus innovation will be needed to continue the improvement. This paper deals with a concept that, on the surface, appears to be more efficient in terms of the costs to provide ventilation. The resulting design is oriented toward increasing the ventilation efficiency through use of a unidirectional ventilation plan but it also promises to increase recovery and decrease the requirements for development entries. To analyze this ventilation concept, two mine layouts with a similar production schedule were planned in a hypothetical 1.83 m (6 ft) coal seam. The first alternative analyzed uses a traditional approach to ventilation with centrally located shafts and a bidirectional ventilation pattern. Using this system, it is necessary to use large-diameter shafts and a large number of main entries. Using the same assumptions on ventilation requirements, the second alternative utilizes unidirectional ventilation whenever possible, a smaller number of main entries and small-diameter blind-bored shafts in the bleeder areas. The comparative analysis is performed using PSU/TDMVS, a computer network analysis program that is capable of determining the ventilation power requirements at any time in the mine life and converting the costs to a present value. The economic analysis is then completed by including the shaft-sinking and entry-driving costs and the costs associated with the recovery of coal that are directly related to the change in the ventilation system. The results are summarized on a present-value basis.

Jan 1, 1987

By R. S. Sheeta, C. J. Bise

The search for a more effective means of coping with methane liberation has resulted in the expanded use of seam degasification. Its advantages are measured not only in reducing the hazards due to methane, but also in producing a marketable commodity, the gas itself. However, the success of a methane drainage system is the culmination of many complex factors, the most important being the coal seam permeability. The two most popular drainage techniques used in mining today are the vertically stimulated borehole method and the in-seam horizontal borehole method. The objective of this paper is to determine the permeability range in which the selection of the degasification technique is based primarily on equipment and economic analysis. A discussion of the equipment involved will be incorporated into examples evaluated by the Pennsylvania State University coal methane simulation model.

Jan 1, 1990