Search Documents

By P. Berendsen

Structures along the rift were subjected to episodic reactivation. Major north-northeast-trending high-angle normal or reverse faults and northwest-trending trans-current fault systems, may exercise control over ore-forming processes. Gabbro and basalt are the dominant igneous rock types. Carbonatite and kimberlite occur in Nebraska and Kansas. Concentrations of Cu, Ni, Co, Ti, Au, Ag and PG-minerals are known to occur in this setting Arkosic sandstone, siltstone, shale and minor carbonate units occur on top of the rift basalts and in flanking basins where they may reach thicknesses of 10 km. The potential for stratiform or unconformity-related metal liferous deposits must be considered.

Jan 1, 1986

By A. W. Khair

This paper presents an engineering approach to solve a complex ground control problem at reduced cost, allowing the mine to be operated safely and economically. The mine has experienced serious and complicated cutter roof problem in the entries. This cutler roof problem has delayed the advance of the entry development considerably and cost of these entries is very high due to the requirement of very heavy artificial supports. The analysis includes assessment of the cause of cutter roof and step by step action taken to improve the entry condition through appropriate longwall panel entry design and roof support system. The approach for solving the problem was two-fold: 1) to apply yield pillar concept in order to reduce the effects of in-situ horizontal stress in the roof strata and 2) to find an effective way to reinforce the roof strata and to support the fractured roof and avoid caving.

Jan 1, 1990

By T. Tamagawa

A gaseous chlorination process for hydrometallurgical treatment of a chalcopyrite concentrate was investigated. The overall process is visualized to consist of low temperature chlorination-selective oxidation, followed by aqueous chloride leaching and SX-EW for producing electrolytic copper elemental sulfur and ferric oxide. In this article, the chlorination phase of the processes is described. Initially, the chlorination behavior of chalcopyrite-concentrate micro-pellets was investigated using a small batch-type fluidized bed reactor. The optimum conditions thereby established was used in continuous chlorination tests. The chlorinated products thus prepared were used in the selective oxidation phase of the investigation.

Jan 1, 1999

By R. Bhaskar

The advantages of recirculation of air in underground mines have been well recognized, and several papers have been written on the subject. Issues of concern to the various segments of the mining industry relate to the health and safety of workers, specifically, methane and respirable dust build-up in the air, high humidity and temperature at the work face. This paper presents a survey of various studies pertaining to recirculation as a prelude to the experimental and quantitative studies performed by the authors. Experiments were performed at a trona mine on the transportation and deposition of dust along the return airways, for three different velocities. Modeling studies were performed using dust deposition models. The model predicted data were compared with experimental data in order to lay the foundation for the development of advanced predictor models for recirculation in trona mines. Two models for dust deposition were analyzed. The model predicted data are in divergence from the experimental data, indicating the need to develop better models.

Jan 1, 1992

By Robert L. Wade

The two primary goals in underground coal mining are to improve safety and to lower mining costs per ton through increased productivity. However, as evidenced by the drastic decrease in. productivity since the enactment of the 1969 Coal Mine Health and Safety Act, (the Safety Act), these goals appear to be mutually exclusive. Millions of dollars have been spent in the res, arch and development of systems to solve this problem. Before the Safety Act, "productivity had experienced a 25-year history of continued increases ...? (Douglas, 1980). But since its enactment there have been dramatic decreases in productivity accompanied by phenomenal increases in mine costs. Labor trends, depletion of the more readily minable underground coal reserves and other factors have contributed to this situation, but the dominant factor is undoubtedly the Safety Act itself. To illustrate, prior to 1969 underground coal mine production was much greater than surface mine production but since then underground mine production has been declining at a rate greater than the overall growth rate of total coal production.

Jan 1, 1985

By R. R. Swanson

Liquid ion exchange is becoming more and more important in hydro-metallurgical processing and recovery of metals. The key to success for this process are reagents which have suitable operating characteristics. One of these important characteristics is a relatively fast phase separation rate in the extraction and stripping circuits, as this greatly affects the size of plant required. A test for measuring phase separation rate is needed to help evaluate liquid ion exchange reagents. Such "a test also would be useful for evaluating carrier solvents that are used for diluting the re-agents. In fact, one standard test method would be very desirable as it would provide a common basis for comparing reagents and sol-vents. The phase separation test described in this paper has been used successfully for several years with the copper reagent, LIX®64N. The test is set up for feed liquors containing low copper concentrations. For other types of systems, modifications in procedure probably would be necessary. However, this test and the associated apparatus could be the basis for a standard phase separation test.

Jan 1, 1972

By Y. J. Wang

The Hardy Cross iterative method is the most popular technique for solving a ventilation network problem with natural air splitting. This method traditionally solves each mesh equation by an approximation during each iteration. Thus, it is interesting from both a theoretical and a computational viewpoint to be able to solve for an exact solution to the mesh equation. Presented in this paper is an algorithm for computing the exact solution to the mesh equation with a variable fan pressure. The algorithm uses signum functions for air quantities to generate an alternative mesh equation in the form of a quadratic equation that has two solutions defined by the well-known quadratic formula. The condition that the derivatives of the alternative and the original equations must be the same provides a basis for the correct choice between the solutions.

Jan 1, 1998

By L. M. Cenegy

The formation of scale is common in gold ore processing plants. A working definition of scale, applicable to the various scaling conditions found in gold ore processing plants, would be: "a hard, tightly adhering deposit formed in place by the precipitation of calcium-bearing mineral compounds from water". The most common scale found in gold processing plants is calcium carbonate (CaCO3) although calcium sulfate (CaSO4) is occasionally a problem.

Jan 1, 1990

Application of flotation for the removal of hydrophobic compounds from soils was studied. Bench scale flotation tests were conducted on artificially contaminated soil, using both conventional mechanically agitated machine and flotation column. Flotation parameters tested include surfactant collector type, conditioning time, flotation time, surfactant dosage, pulp pH, solid/liquid ratio in conditioning and pulp temperature. It is found that with conventional flotation 74% removal of the contaminant was achieved from soil particles in the range of 75-830 µm; with column flotation up to 80% of oil could be removed from the 250-830 µm soil fraction, and 65% from the 75-830 µm fraction. Flotation was found to have considerable potential for cleaning up contaminated soils.

Jan 1, 1998

By Larry DeGraff

With the increase of new mine development in the past several years, many coal mines have decided to self- perform the design and construction for their slope development projects. The development process of determining the proper configuration is challenging, and a major economical consideration. Greenbrier Smokeless Minerals engineering staff and consultants, along with DSI/American Commercial, developed a support configuration that was best suited for their slope. The developmental process took into consideration the length of slope, depth of slope at the high-wall transition, economics of a single or multiple entries, waterproofing, stresses on the steel supports and lagging during the backfilling operation. This paper describes the developmental concept of using a single entry, side by side configuration, using steel ?Banjo String? supports with steel plank lagging, to develop a long term permanent installation in a cut and cover application.

Jan 1, 2009

By Dell H. Adams

Coal exploration may be defined as the acquisition of data necessary to define and acquire a block of coal which can be mined at a profit. Unlike ore minerals, coal resources are widespread and relatively abundant with supply exceeding demand in almost every case. Thus simple discovery of coal is generally not enough. The chemical and physical variability of individual coal seams, the capital intensive nature of coal mine development, and the changing patterns of utilization require that a multiphase, three-dimensional evaluation be made of each potential reserve. Factors which must be investigated include not only the quantity and quality of the coal but also the geologic, hydrologic, and engineering characteristics of the seam and its surrounding strata. Acquisition of property to provide a secure base for exploration and mine development is equal in importance to the geologic and engineering programs. The successful development of a coal reserve requires that control of coal and, in the case of a strip mine, the surface be in the form of contiguous blocks of sufficient size to support mining.

Jan 1, 1981

The public relations problems of users of explosives have greatly increased within the past few years. One reason is that explosives and blasting agents are being consumed in increasing quantities. The principal reason, however, is that more people have become physically affected by blasting. Mines, quarries, and construction sites that were formerly in relatively remote locations now find themselves near congested areas. New express traffic ways being constructed to connect the suburbs with downtown areas are being built through the middle of long-established business and residential neighborhoods. The public becomes aware of blasting by two physical sensations-vibration and noise. Vibrations are usually so slight as to be negligible, and in most cases the only sensation noted is noise. The reduction of vibrations to this low level has been primarily achieved by the use of blasting practices and explosive products recommended by vibration engineers based on seismograph recordings. Unfortunately, very little scientific attention was given to the accompanying physical sensation-noise.

Jan 1, 1962

By B. A. Firth

The presence of misplaced ultra-fine particles has been shown to decrease the separation efficiency of unit operations used in coal preparation. Although the classification of fine coal was considered to be adequate for the needs of the coal industry during the 1970's and 1980's, it has become apparent that further improvements in the yield/ash/moisture relationship achieved by coal preparation plants will require increased efficiency in this size separation step. This paper describes the issues which are evolving in this area, and the capability of current and developing techniques to address the problems which need to be overcome.

Jan 1, 1996

By G. S. Adisoma, J. J. K. Daemen, R. O. Roko

A common assumption in determining the shear strength of a rock joint using a direct shear test is that the surfaces undergoing relative shear are in complete contact. Furthermore, the limiting displacement associated with the residual strength values is obtained based on engineering judgement through visual inspection of shear force versus displacement curves. This study proposes a systematic way of determining the residual shear strength of rock joints by evaluating the limiting displacement leading to a minimum cohesive strength value and taking the true area of contact into account. The results of the study indicate that there is a limiting displacement associated with the residual shear strength, and some rocks may have an inherent interface residual cohesive strength different from zero. When the cohesion is different from zero, the residual shear strength is likely to be underestimated if the true area of contact is not considered. In the case where zero calculated cohesion is obtained, the area of contact has no bearing on the shear strength equation because the frictional force depends only on the normal load.

Jan 1, 1986

By T. Gonzales

Magma Metals Company operates an Outokumpu Flash Furnace, four Peirce-Smith Converters and two Anode Casting Wheels supported by six Anode Vessels. Process gasses from the Flash Furnace and Converters are treated in a two train/double contact sulfuric acid plant. Sulfur capture for the smelter is +98%. The new flash furnace was commissioned on July 7, 1988 and has processed over three million tons of sulfide concentrate without a major rebuild. Magma has gained unique experience in the operation of the flash furnace at high oxygen enrichments with low off-gas dust loadings. New procedures have been developed to maintain secondary material generation at equilibrium and for maintaining metallurgical control of operating parameters. This paper describes all the procedures, operation control parameters and operating philosophy that has allowed Magma to achieve superior performance.

Jan 1, 1992

By Theodore Triplett

To assess the value of various subsidence mitigation techniques, twelve linear foundations were constructed above a longwall mine. The structures were monitored during and after undermining, and footing curvatures at the time of cracking were compared with predicted values. An unreinforced concrete footing sustained substantial damage. Other footings received varying degrees of damage, with inclusion of a sand layer significantly affecting performance. A post-tensioned concrete foundation suffered minimal cracking. Also, a technique developed by the Bureau of Mines is presented for determining the subsidence, slope, curvature and strain of the ground surface.

Jan 1, 1986

By J. A. Pontius

The Cresson Deposit is located in central Colorado within the historic Cripple Creek Mining District. The deposit has moved from its initial discovery in 1990 to full production in less than five years (current reserve nearly two million ounces). This accomplishment required a great deal of cooperative teamwork between the exploration, development, permitting and corporate groups. Nowhere was this cooperation more evident than in the construction of the geologic block model. The detailed modeling of gold and its metallurgical characteristics formed the foundation upon which critical financial and design decisions were based.

Jan 1, 1995

By Richard W. Patton

With the advent of the Clean Air Act and the installation of flue gas desulfurization (FGD) equipment (scrubbers) on coal fired power plants, the management of solid wastes has taken on added importance. Aside from the large amounts of fly ash and bottom ash usually generated, large quantities of liquids in the form of scrubber sludge are also produced. These wastes must be disposed of within the constraints of land and water quality regulations. This paper describes the practices adopted by the electric utility industry in denting with this problem, including methods of generation and treatment, quantities and characteristics of the materials, and transportation and disposal practices. The paper also briefly describes final product characteristics and several applications for commercial utilization and land reclamation.

Jan 1, 1983

By Martin Knights, Geoff Featherstone, John Flanagan, David Lawrence

The proposed paper will address specific transport, engineering, environmental and community related issues concerning the current construction and future operation of Europe’s biggest urban road tunnel project—the US$500m Dublin Port Tunnel. Situated in Ireland’s capital, the three mile long, 40 ft diameter twin tunnel project encounters a range of ground conditions using TBM, Shield, Cut & Cover with diaphragm walling and major slope stabilisation and Multi-jacked pipe techniques. Where possible units of measurement are given in feet and inches.

Jan 1, 2003

By E. A. Brecke

The Cave-In-Rock Flourspar District is located in the northeast part of Hardin County, Illinois and is the most northeasterly occurrence of flour spar of the Illinois-Kentucky Flour spar Area. The occurrence of these deposits is confined to an area about one and one-half miles wide and five miles long parallel to the Peters Creek Fault (Fig. 1) The delineation of several features that may be described as breccia pipes has permitted the definition of the point of ascent of solutions to the host horizon and the lateral spread from these points.

Jan 1, 1962