Search Documents

By R. J. Matetic

The impact of longwall mining on the local hydrological regime has become an important environmental focal point. Unfortunately, only a few studies have addressed the timing and range of well fluid level fluctuations and the associated ground movement. Furthermore, even fewer studies have determined the influence of longwall mining on water quality. The U.S. Bureau of Mines is providing insight into this environmental concern through a program of field case studies. One such study was conducted in Cambria County, PA where five observation water wells were drilled above two adjacent longwall panels. In this study, three wells were completed as nested piezometers and the remaining two served as producing wells. The piezometers were positioned along a line oriented subparallel to the longwall face and were located at the centerline of each panel and over the intervening chain pillars. The piezometers were designed to monitor fluid level fluctuations in both shallow and deep water-bearing zones. Slug tests were conducted before and after mining to characterize changes in hydraulic conductivity of the respective water-bearing zones. Pressure transducers and data loggers were installed to provide continuous fluid level fluctuation data as mining developed through the study area. The producing wells were drilled to provide water quality information. One well was located directly above the centerline of a panel and the other was positioned over the panel's set-up rooms. The wells were designed to simulate domestic use and were produced daily, for four hour intervals, throughout the study. Samples of the produced water were collected before and after mining progressed through the area. In addition, an array of monuments was installed near the study wells and was periodically surveyed to characterize mining-induced surface deformations. This study shows that: a) the observed changes in ground water chemistry did not affect the potability of the water; b) short-term major water level fluctuations occur at the approximate time of undermining; and c) water level recovery begins before the process of subsidence is complete.

Jan 1, 1986

By R-H Yoon

The MicrocelTM column flotation technology has been developed based on the fundamental understanding that the first-order flotation rate constant increases approximately as the inverse cube of bubble size. In this technology, bubbles in the range of 100-400 pm are generated by pumping aerated slurry through an in-line static mixer. The high-shear agitation provided by the in-line mixer produces small air bubbles without requiring large frother additions. This column has been tested successfully for processing a variety of non-metallic minerals including kaolin clay, graphite, phosphate, and feldspar.

Jan 1, 1993

By Bryson D. Trexler

Slope stability in open pit mines is governed by rock structure, rock quality, ground water conditions, blasting, pit geometry and excavation method. Of these factors, the control of ground water pressures often represents the primary tool to improve slope stability. Production equipment has recently been used to stabilize two slide areas by dewatering using blasthole drills for vertical holes and secondary drills for horizontal holes. This paper describes both of these dewatering programs and contrasts an earlier slope stabilization program that employed a subcontracted horizontal drill.

Jan 1, 1983

By Dale R. Andrus

Why is there such an increased thrust toward positive multiple use land management and where will it lead? History and purpose of the mining law of 1872. John Marshall discovered gold at Sutter?s mill near Coloma, California, on January 19, 1848, and utter chaos resulted. The great migration of people to the undeveloped western lands had begun. Prior to this discovery, copper, lead, and iron had been the minerals for which the laws were made. With this discovery of gold on the public domain, it became apparent that congressional legislation was necessary. This became even more apparent as each of the numerous mining districts which were springing up in California, and elsewhere in the west adopted local miners' customs to regulate their activities. Although these early miners acted under mining district rules and in some cases state regulations, they were, in reality, appropriating minerals without sanction of federal law.

Jan 1, 1970

By H. B. Miller

By its nature, underground metal mining is unlike any other business in the industrial sector. Operations are continuously exposed to economic risk as a normal consequence of mining due to uncertainties associated with the? deposit, excavation, and ever changing political, regulatory, and market conditions. Out pacing advances in productivity and technology, these conditions have contributed to the steady decline of underground hardrock mining in the United States. This paper investigates the trends and major factors believed to be responsible for this decline. Special consideration is given to changes in direct operating costs, labor productivity, and production capacity.

Jan 1, 1995

By St. Mergentime, K. Zeidler, V. Gall

2001, the New Jersey Transit Authority commissioned the JV Merco-Obayashi with the rehabilitation contract of the approximately 130-year-old, 4,200 ft long, partially brick- lined Bergen North Tunnel. The contract entailed the tunnel enlargement, shotcrete and rock dowels initial support according to the NATM, a waterproofing system, tunnel drainage and a cast-in-place concrete lining. The rock conditions encountered required design adaptations and significant modifications of the initial tunnel support. Flexibility, skill and extensive experience on the Authority’s and Contractor’s side finally lead to a success. This paper describes the operations and design modifications carried out.

Jan 1, 2003

By Haydn H. Murray

Kaolin is an important industrial mineral because it exhibits desirable properties in many applications and because of its relatively low cost, Approximately 2,000,000 tons of kaolin from Georgia and South Carolina are processed and used commercially in the United States each year. Strictly defined, the name kaolin is applied to a group of hydrous aluminum silicates of which the mineral kaolinite is the most common. Kaolinite has such desirable properties as natural whiteness, chernical stability, non- abrasiveness, and very fine particle size. Kaolinite particles are characteristically thin, flat, and hexagonal in outline. The particles range in size from submicron to as much as 40 microns (equivalent spherical diameter). In addition to the general properties mentioned in the first paragraph, it is soft, has low viscosity at high solids content in many systems, is readily wet and dispersed in water and some organic systems, and can be produced with a controlled particle size distribution. Some of the important physical constants of kaolin are: specific gravity, 2.60; index of refraction, 1.56; hardness (Mohs scale), 2; fusion temperature, 1850°C; dry brightness, 78-92 percent.1

Jan 1, 1965

By A. Vien

MOCCA is a Multivariable Optimal Constrained Control Algorithm developed specifically for non-square industrial control applications with practical difficulties such as interactions, time delays, constraints, modelling development, etc. MOCCA consists of an off-line simulation/translation module, for tuning the control parameters, and an on-line module that implements the designed control law. This paper describes an evaluation of MOCCA on the Hemlo grinding circuit which comprises one open circuit ball mill and two closed circuit ball mills in series. In this case a 4x4 unconstrained control problem was considered. The manipulated variables included the fresh ore feed rate and three pump box water additions. The controlled variables were the grinding circuit product particle size and three pump box levels. In this application soft constraints were implemented through control action and control error weighting. The feedforward capability of MOCCA was used to compensate for a measured water flow disturbance to one of the pump boxes. MOCCA performed very well during plant evaluations when compared to the original classical multi-loop control strategy and proved to be quite robust. Perhaps most importantly, the process engineers and plant operators have a high level of comfort both in understanding MOCCA's general operating principles, and with its demonstrated performance.

Jan 1, 1991

This paper reports on the behavior of mercury and its compounds during the thiosulfate leaching and recovery of gold. Thiosulfate solutions are shown to dissolve Hg0 and Hg2Cl2 to a similar extent as cyanide, but the leaching of HgS is significantly slower in thiosulfate solutions compared to cyanide. Hence, the use of thiosulfate may be an option for treating ores containing high levels of cinnabar, especially since the legislation concerning the discharge or sale of mercury is becoming more restrictive. The deportment of mercury during gold thiosulfate loading and recovery using a strongly basic anion-exchange resin was also studied. Although the mercury thiosulfate complex loads on the resin, the adsorption is weaker than for gold, with an equilibrium constant between gold and mercury of 51. Resin loaded with gold, mercury and copper was pre-eluted with thiosulfate (to remove copper) and eluted with a chloride and sulfite eluant. The majority of the mercury is eluted by the eluant and, hence, its deportment closely follows gold and the eluate would need to be treated to remove either mercury dur-ing or prior to gold electrowinning.

Jan 1, 2010

By F. J. Susko

The Bureau of Mines applied a flotation model to the hydrodynamics of the Bureau-developed rapid flotation system. Rapid flotation is a process which separates the bubble-particle attachment and froth-pulp separation stages of the flotation sequence into two discrete unit operations allowing the operations to be individually optimized. Both an air-injected hydrocyclone and an in-line mixer were used as the bubble-particle attachment unit and a shallow-depth froth separator was used to separate the ore-laden froth from the pulp. A 10-L/min batch system was tested on a coarse coal feed sample. The system was tested using two different bubble-particle attachment units at various aeration levels in order to test the flotation model. The results of the flotation model reflect general trends observed in the experimental data.

Jan 1, 1993

By M. L. Wouden

The Bureau of Mines investigated pegmatite and granite formations at Copper Mountain, Fremont County, Wyoming, for recovery of tantalum and niobium. Sampling of surface exposures identified about 1.27 mega tonne of pegmatite resource material ranging between 0.02 and 0.04% Ta20, and 0.007% Hb20,. Beneficiation studies were conducted involving coarse-grained and fine grained pegmatite samples. Over 80% recovery of the coarse-grained tantalite was achieved in a concentrate averaging over 45% combined tantalum-niobium oxide. Lower concentrate grades and recoveries resulted from the treatment of fine-grained pegmatite.

Jan 1, 1991

By M. A. Reinsel

New technology for removal of nitrate from low-temperature waters has been developed. Typical results from the first operational-scale system (operating at a metal mine in Montana since January 1996) are over 90 percent nitrate removal at a flow rate of 130 gpm and a water temperature of 12°C. The system also operated successfully at flow rates as high as 300 gpm and water temperatures as low as 2°C. The ABC is advantageous because it is: a) cost-effective to design, construct and operate, and b) effective at cold water temperatures. The system can be designed for a variety of flows, nitrate concentrations, water temperatures and water qualities.

Jan 1, 1998

By J. G. Groppo

A beneficiation process has been developed to provide selective separation of unburned carbon from high LOI fly ash. Previous reports of utilizing froth flotation to achieve selective separations required long residence times and high reagent costs. A proprietary reagent system has been developed to address both of these limitations. Based on the results obtained from laboratory and pilot-scale investigations, a flowsheet design has been developed to produce two distinct usable products from class F fly ash; low LOI ash and a high carbon product suitable for reburning or further upgrading. A process flowsheet and description are presented.

Jan 1, 1996

By J. O. Marsden, J. H. Gourdie, J. R. Arnold, J. G. Mansanti

During the testing and design of the Gold Fields' Chimney Creek mine, it was found that a much higher carbon loading was possible with CIC (carbon-in-solution columns) than with CIP (carbon-in-pulp). In an effort to keep the carbon handling minimized, an emphasis was put on forcing gold to the CIC circuit rather than the CIP. After considerable study, it was found that a circuit with two thickeners and an interstage leach would force 90% of the gold to CIC. Computer modelling indicates that the benefits of the hybrid circuit include higher recovery, less carbon handling, fewer leach tanks, and lower reagent costs.

Jan 1, 1990

By H. E. Rojas

The primary objective of most comminution operations is liberation; however, mill performance is generally quantified in terms of particle size. Only recently has the use of image analysis equipment made it possible to quantify mill performance on the basis of liberation. In this investigation, a series of tests were carried out to study the effect of mill operating parameters on the liberation of sphalerite from a sphalerite/dolomite ore. The parameters studied included mill rotational speed, mill loading and ball size. The results of this work appear to indicate that sphalerite liberation is improved under conditions that promote impact breakage, while dolomite breakage is enhanced under attrition conditions.

Jan 1, 1990

By C. L. Schneider

The calculation of the liberation spectrum in the product from continuous milling operations is a problem of considerable importance and is difficult to solve because the population balance equation must be integrated in two-dimensional space. Complete solutions require the estimation of a large number of parameters unless a structural model of the ore texture can be used. A very simplified textural model based on the use of the modified Andrews-Mika diagram and the PARGEN simulation of multi-phase particles has been formulated and is used to simulate the behavior of a continuously operating laboratory ball mill. A sensitivity analysis for this mill has been done to show the likely effect of model approximations on the predicted liberation spectrum which will be measured.

Jan 1, 1992

By Lloyd C. Venburg

Analytical and computer models are used to evaluate information obtained for the design and development of mine water control systems. Geologic, hydrologic, geophysical, biological, and chemical data must be gathered for use during all stages of mine development. Models allow the geohydrologist to use these data to predict the amount of ground-water inflow, the impact of dewatering and stream diversion on the hydrologic regime, equipment needs, and dewatering schedules. Stratigraphic and lithologic changes, faults, recharge and discharge areas, and aquifer parameters should be incorporated into the model to design and develop an effective mine water control system.

Jan 1, 1982

By J. B. Mitchell

Comminution methods for base metal and precious metal ores have had considerable attention from mine operators, equipment suppliers and design engineers for many years and much of their work has been well reported. This interest derives from a healthy concern with the costs of comminution, often the largest single cost factor in ore dressing of hard ores. Many imaginative innovations have resulted. One notices a trend toward autogenous and semi-autogenous methods, combined with a trend toward very large equipment. Unfortunately, there has been less obvious cost incentive to experiment with softer ores. This is unfortunate because the consequences of inappropriate comminution methods can have an important effect on overall economics by influencing down stream processing and salability of final products. This paper concerns some of the factors to be considered in the selection of comminution methods for potash ores, and gives some specific examples to illustrate some of the principles involved.

Jan 1, 1969

By J. Villeneuve

Steady-state simulation has proved to be a very useful aid in designing new plants and optimizing existing ones. The algorithms and data definitions of existing simulators often, however, require a great deal of expertise for implementing a simulation-based methodology. The constraints imposed by conventional simulators are explained and the advantages of a new algorithm, the Objective-Driven Simulation, are shown. These advantages are a) an improvement in the simulation results, which enables simplifications of the methodologies used, and b) the possibility of taking into account economic objectives for plant operation, thus extending the range of application of steady-state simulation.

Jan 1, 1992

By Donald L. Freed

Design, development, factory test, and in-mine evaluation plans are presented for an Automated Extraction System (AES) that has been designed to fill needs which are present in the Mining Industry. The philosophy of design and proposed operation of the machine, as well as the relationships between these factors, and final machine configuration are reviewed. The AES is designed to overcome production problems resulting from the regulation of roof control, clean-up, ventilation, dust suppression, and operator protection required by the Federal Coal Mine Health and Safety Act of 1969. The design permits more continuous operation and greatly improves operator safety. The machine is a full-face drum-type continuous miner which includes self-advancing, continuous temporary roof support. Onboard self-advancing face ventilation, dust suppression, and air scrubbing equipment are also included in the design. A further improvement over existing equipment is the incorporation of an automatic programmed cutting cycle control system. All mining functions including movements of the roof support system are handled by this automatic system.

Jan 1, 1977