Search Documents

By R. J. Sweigard

Many states are considering the need to establish or modify policy relating to the disposal of coal ash. One of the primary concerns is the impact of leachate from the ash disposal sites upon groundwater and nearby bodies of surface water. A detailed site investigation was conducted at a coal ash disposal facility associated with a power generation station. The disposal site is situated alongside a major river. Monitoring wells were installed and soil samples were taken for characterization. Groundwater models were used to simulate migration of leachate from the disposal site toward the river. Such models could be used potentially to verify regulatory compliance. This paper addresses the validation and adaptability of these models to this case and their usefulness as possible tools to be used in future environmental audits.

Jan 1, 1992

By Jonq-Keh Lee

This paper deals with the effects of air leakage from intake to return airways through a series of stoppings on the analysis of coal mine ventilation. The mathematical model which assumes continuous leakage along adjoining intake and return airways is reviewed, and a new mathematical approach is presented based upon the concentrated leakage through individual stoppings. The procedure incorporating the new method in the analysis of coal mine ventilation networks is also discussed.

Jan 1, 1984

By B. K. Baird

The application of cutoffs during and after pit optimization is examined for a lower-grade multi-metallic copper deposit. Pit optimization requires calculation of the net revenue associated with each mining block, incorporating parameters such as metal prices, grades and expected recoveries, mining and processing costs, smelting and refining charges, and penalty element and royalty charges. Sensitivity analysis during pit optimization reveals which of these parameters have a significant effect on the total contained resource tonnage and total contained non-discounted revenue in the optimized pit. The cumulative effect of changing several of the more significant parameters is investigated. Application of a copper cutoff grade to a block inside the optimized pit could result in the less than optimal extraction of the resource. A block with copper grade below the applied cutoff could be economic due to the presence of other metals. Conversely, a higher copper grade block may be sub-economic. The relative merits of applying a copper grade cutoff, "equivalent grade" cutoff and dollar value per ton cutoff to blocks inside the optimum pit are discussed.

Jan 1, 1999

By Harold F. Yde

Hydraulic tailings fill in the Butte deep level mines was based upon studies made in 1958 by the Anaconda Company Mining Research Department, which published Bulletin No. 35, entitled "Hydraulic Stope Filling". Since then, many things have changed. At the time of the Research Departments study, dry mine tailings were hauled by rail cars from the Anaconda tailings ponds, twenty-five miles distant, to the underground mines' tailings fill plants at the Leonard Anselmo, and Mt. Con Mines. Now, with the installation of the new Weed Concentrator in Butte, tailings is delivered by pipeline to a cyclone at the Kelley Shaft, and stope filling has become more highly automated and streamlined. Presently, mill tailings at approximately thirty percent solids by weight, is pumped from the concentrator, eight thousand feet horizontally and upward, to the Kelley Fill Plant, where they are dewatered and deslimed by three Krebs Model D20B Cyclones, which discharge the material into the cased and grouted mine delivery bore holes at desired densities up to seventy percent solids. The vertical boreholes and four-inch rubber lined Victaulic pipe carry the material downward to horizontal distribution lines, which in turn tap into the stops-filling, three inch, unlined steel Victaulic pipelines. The slurry may travel several thousand feet before it finally discharges into the stope, where it lends support to the mined-out area.

Jan 1, 1969

By B. Caines

Much of the mining industry in North America is in a crisis state. Host producers are operating at production levels well below capacity, some have been merged or sold, while others have been mothballed or closed permanently. For many of us still operating, the future is uncertain. Despite the many cutbacks and closures, there is still an abundant supply of minerals in the world market and there is almost no hope for any relief on price pressures on most mineral commodities in the near future. The Iron Ore Company of Canada (IOC)operates an iron ore mine, a concentrator and a pellet plant known as the Carol Project located in Labrador City, Newfoundland. This concentrator and the pellet plant have the annual capacity to produce 20 million and 10 million tons respectfully. A company owned and operated railway links this operation with the dock terminal facilities in Sept Iles, Quebec.

Jan 1, 1987

By Robert L. Frantz

The U.S. Bureau of Mines (USBM) established on August 15, 1983, a Generic Mineral f Technology Center (GTC) for Respirable Dust within the Mining and Mineral Resources Research Institutes (MRIs) at The Pennsylvania State University (PSU) and West Virginia University (WW) in association with participating MRIs at Massachusetts Institute of Technology (MIT) and the University of Minnesota (UMN). The primary goal of the Center is to reduce the incidence and severity of respirable dust disease through researching and advancing the fundamental under- standing of all aspects of respirable dust associated with mining and milling and the interaction of dust and lungs. Other Center activities include the training of engineers and scientists, graduate students and undergraduate students through their respective institutions, and the technology transfer to the industry. The Center also serves as the reference center for publications in the respirable dust area.

Jan 1, 1986

By Mitchell Gordon

Two mineral processing facilities in North America required near terminal density slurries to perform de-bottle necking in their circuits. The installation at Barrick Goldstrike to ensure efficient oxidation conditions and throughputs in the refractory ore treating autoclaves. The Kidd Metallurgical Division unit to provide a steeper tailings slope to extend the life of the existing tailings dam. To achieve these goals, both operations selected a Supaflo "High Compression" Thickener following on site pilot plant evaluation. Commissioning and the first year of operation is reviewed. Operating data is compared with the pilot plant data. In particular, unusual doughnut formation at Goldstrike and the effect of temperature on the terminal density at Kidd Metallurgical Division are discussed.

Jan 1, 1997

By Paul Dean Proctor

The known northern ore zones of the New Lead Belt of Southeast Missouri extend to the drainage divide between the Meramec River draining north and east and that of the Black River draining southward. Intensive geochemical studies related to the environmental impact of the new mining area have been carried out in the vicinity of some of the newly developed mines, mills and smelter complexes (Bolter,1970; Gale, et al, 1973; Wixson, et al, 1969, 1977). Other investigations have related to fringe studies of the Northern New Lead Belt and the possible additions of heavy metals to the surface waters, stream sediments and selected aquatic life (Proctor, et al, 1975, 1976). Similar studies have been completed in the Joplin area in the Tri-State district, and in the fringe area near Springfield, Missouri (Proctor, et al, 1974). A surface geochemical study is currently underway on the lead-zinc-copper-cobalt-nickel province near Fredericktown, Missouri (Proctor and Sinha, 1977). This report summarizes some of the distribution patterns of heavy metals in the waters, stream sediments and selected aquatic life in the Upper Meramec River drainage basin just north and west of the known northern portions of the New Lead Belt of Southeast Missouri. The region studied includes the site of the proposed and somewhat controversial Meramec Dam and the reservoir site behind it. Some 3905 km2 (1508 mi2) are included within the drainage basin of the Upper Meramec River. Six distinct drainage areas are included within the drainage basin; 1) a combined, lightly industrialized and farm area around Rolla and Salem, Missouri representing the Dry Fork drainage; 2) a primitive, mostly forested area with some farms and cattle rancheseast and north of Salem, Missouri comprising the Upper Meramec River

Jan 1, 1977

By Wilfred M. Kenan

The relationship of various genetic classifications of graphite, their properties and general applications are reviewed. The classifications being amorphous, flake, high crystalline (vein) primary synthetic graphite and secondary graphite. The properties discussed are size, carbon, sulfur, ash content, general chemical analysis and degree of graphitization of each type. The major sources for natural and synthetic graphite powders are discussed in addition to factors which govern the cost as well as the supply. The economics of graphite are basically determined by the consumer and the end application. Graphite is a strategic mineral and is on the government stockpile list.

Jan 1, 1984

By Christian F. Baiz

A new agenda has risen. Born out of governments' policies and world economies, the years ahead will carry with them reduced growth. For inflation dependent and capital intensive industries, such as metals and mining, as well as most other natural resource industries, a period of long-term contraction in outmoded and costly capacity will evolve. This will be supplanted by new, lower cost capacity in some cases, but only if the total cost of production, including cash operating and debt service costs comes in at or below current market conditions. The industrial outlook can be characterized as bearish. As one major U.S. bank economist put it, mining companies planning their five-year forecast from 1984 out, should take the current market conditions and straight-line them to the end of the decade. With low growth and low inflation, the real price of metals will remain flat or slightly declining. As a result, capital funding will be problematic. The low cost producer, that is one with low cash costs and low principal and interest costs per unit of production, will succeed.

Jan 1, 1984

By O. Ozcan

Oleic acid has been almost invariably used in the flotation of siliceous fluorite ores. The performance of oleic acid, however, deteriorates with carbonaceous fluorite ores. Oleoyl sarcosine developed recently has been found to produce results superior over oleic acid with ores containing high calcite contents. While the mechanism of oleate adsorption is usually considered as chemisorption involving calcium oleate formation on both calcite and fluorite, no mechanism has been so far proposed to explain the adsorption mechanism of oleoyl sarcosine. In this study, the selectivity of oleoyl sarcosine, as inferred from flotation, zeta potential and infrared measurements, is ascribed to the interaction of fluorine ion to the nitrogen via hydrogen bonding.

Jan 1, 1994

By P. D. Chamberlin

The interface between precious metal miners and gold refiners has been an uneasy interface over the years. The reasons for this interface and its apparent uneasiness and lack of trust include technical factors, economies of scale, and cultural differences. Technical factors take two forms. First, concentrates, precipitates and sponge produced at the mine site are notoriously difficult to sample and a non-representative sample can be the cause of misunderstanding and distrust. Dore, however, is homogeneous and can be correctly sampled and analyzed. Second, the technology and chemistry of fine gold and silver production is complex and quite different from that of dore production. Most mining companies are content not to be involved with additional processing steps.

Jan 1, 1986

By P. Stanley Jacobsen, Hemant B. Gala, Richard E. Hucko

Coal is the nation's most abundant fossil energy resource. However, its use is limited because of the nature and amount of associated impurities, such as mineral matter, sulfur, trace elements, and moisture. The moderate-to high- sulfur content of many U.S. coals is of particular concern as current and newer, potentially more stringent, regulations require reduction in sulfur oxide emissions. Release of particulates, NOx, and other pollutants during the coal-use cycle is also of concern. The current practice of controlling sulfur oxide emissions in the major steps of the coal- use cycle is limited mainly to coal preparation by physical beneficiation and, to a smaller extent, to post-utilization cleanup (flue gas desulfurization). Approximately two-thirds of the coal from states east of the Mississippi river is physically cleaned, whereas only 15% to 20% of the operating boilers in the utility industry are equipped with scrubbers to desulfurize the flue gas (Henzel, 1988). Physical beneficiation methods can be very effective in removing mineral matter, including pyritic sulfur, from coal. These processes take advantage of the differences in physical proper- ties between coal and mineral matter to achieve the separation. In a typical physical cleaning operation, raw coal is crushed to about a 50-mm (2-inch) top size. It is then screened into coarse, intermediate, and fine sizes. Crushing the coal liberates some of the ash-forming minerals, including a portion of the sulfur that is not chemically bound to the coal. The per- centage of impurities freed from the coal matrix generally increases as the coal particle size decreases. The coarse- and intermediate-sized coals are typically subjected to a cleaning pro- cess based on differences in specific gravity between coal particles and the associated impurities. Such cleaning processes used include jigs, dense-medium baths, cyclone systems, and concentrating tables. The fine-sized (typically less than 0.5-mm) coal, if beneficiated, is typically cleaned using a froth flotation technique based on the differences in surface proper- ties between coal and its associated impurities. At fine sizes, greater cleaning potential exists because a greater portion of the impurities is released from the coal matrix. However, this potential is not fully realized owing to inefficiencies in separating fine particles using state- of-the-art flotation technology. Overall, current commercial coal preparation processes are estimated to remove up to 60% of the ash and 10% to 30% of the sulfur, depending on the coal characteristics, with product weight recoveries rang- ing from about 60% to 90% and thermal recoveries of about 85% to 98% (Versar, 1985; Science Applications International Corporation, 1987; Hoffman- Muntner Corporation, 1978). For many U.S. coals, grinding to sizes finer than those used in current coal preparation plants is required to liberate most of the physically bound impurities from the coal matrix. As noted, conventional coal-cleaning methods are not very effective at these fine sizes. Accordingly, the expanded use of domestic coal requires the development of advanced coal cleaning technologies that can provide economic performance while reducing environmental impacts. Program Goals and Objectives The overall goal of the U.S. Department of Energy (D0E)'s Coal Preparation Program is to provide the scientific and engineering knowledge base that industry can utilize to produce economically competitive and environmentally acceptable clean-coal products for introduction as market conditions warrant. The coal preparation process(es) should remove undesirable components from coal and improve its handling characteristics, thus making the product coal technically, as well as economically, viable as a competitor with petroleum-derived fuels and natural gas, and with alternative environmental control technologies. The coal preparation process must be applicable to a wide variety of bituminous and low-rank coals. The cleaning process should reduce the variability among clean-coal products from various raw coals, thus significantly increasing the range of potential end uses for each raw coal. To the extent that deeply cleaned coal products have greatly reduced levels of

Jan 1, 1988

By Stephen Krickovic

"Bleeding", as used in mine ventilation language, has a number of meanings among mining men and is regarded with different degrees of importance. This lack of uniformity stems from a number of specific situations. A method that is adequate in a mildly gaseous mine may fall short in a very gaseous mine. Projected bleeders could be dependable under a certain type of roof, and totally unsatisfactory under a different type. Similarly a plan of bleeders can be rendered useless due to undulations of seam and water in one mine and function well in another. Finally, what is effective in a mining system with partial recovery will not suffice with full recovery. You may wonder, then, if there is a common denominator for the essential function of "bleeding". In my opinion, there is, and it can be defined as controlled movement of air across an active pillar line toward the back and outby ends of the adjacent gob area into the headings provided for the purpose. The objective is to maintain as methane-free as practicable a belt adjacent to the working places, so that, if face ventilation is interrupted temporarily, the gas will not accumulate in dangerous volumes at the working faces before ventilation is restored. It's possible for these temporary interruptions to be unnoticed in time or at all. In such cases, ineffective bleeding could cause a disaster. This has happened. To control, there must be power. That is to say, there must be adequate air, pressure differential between the front and back ends of a pillar line to facilitate proper regulation for diverting of air to the various portions of the gob and as far away from the active section as is practicable. As an indication of the importance of pressure, it is noteworthy that one may provide and maintain in a reasonably open condition a heading or two for a bleeder system and fail to obtain effective bleeding .because air pressure differential is inadequate. On the other hand, you are all familiar with the fact that pillar lines in some seams can be ventilated adequately by air flow straight across the gob when the section is near a main return shaft and thus obtains a heavy pressure differential.

Jan 1, 1962

By James W. Mitchell

On December 2, 1942, a scientific team lead by Nobel Prize winner Enrico Fermi first initiated and controlled a self-sustaining nuclear chain reaction. This historic event occurring beneath the stands of the University of Chicago football stadium instantly created an entirely new and tremendously broad area of technology. Indeed, the event probably changed the course of world history and considering the curret energy shortage, it probably came none too soon. Following many technological breakthroughs in the ensuing years, this event led to the first full scale nuclear fueled electric generating plant. In December, 1957, the Shippingport Nuclear Power Plant became operational and the United States had entered the era of the nuclear fueled electric generating station. Today, only fifteen years later, there are some thirty-five operating nuclear power plants in the United States with another 56 under construction and 116 on order. Still, we are only scratching the surface of this tremendous energy source. In 1970, less than one-percent of the total electric generating capacity in the United States was nuclear fueled. By 1985, it is projected that 45% of our generating capacity will result from nuclear power plants. These projections are based upoa statistics of six months to a year ago and considering the current energy shortage and recent attempts by the United States Atomic Energy Commission (USAEC) to speed the licensing process and encourage standardized plants, the contribution of nuclear power to our total generating capacity may be even greater. In summary, it is obvious that nuclear power is now, and will continue, playing an important role in our future. Those factions of government, industry and the professional community charged with fully developing this tremendous energy source must deal with it rationally, logically and expediently. The various environmental considerations in nuclear plant siting play an important role in the overall plan.

Jan 1, 1974

By M. R. Peterson

The U.S. Bureau of Mines has investigated new methods for increasing the selectivity in flotation by creating and regulating reagent concentration gradients within flotation columns at steady-state operation. Gradients were generated and traced in a water-only system with the use of fluorescent dyes, and the effects of various operating parameters on these gradients were investigated. From this investigation, it was found that both gradual and steep gradients could be generated in the froth cleaning zone, and that these gradients could be changed through the manipulation of both physical and chemical operating parameters. The application of reagent-gradient control to mineral systems could improve both flotation grade and recovery in commercial flotation operations without the use of additional flotation circuitry.

Jan 1, 1992

By R. K. Singhal

In an underground coal mining environment, a frictional ignition may be defined as the ignition of an explosive air/ methane/coal dust mixture by mining machinery. As the use of power loading equipment has become more widespread, frictional ignition incidents have increased. There have been many fatalities and injuries from this cause including the death of eleven miners in Sydney coalfield of Nova Scotia, Canada in 1979. This paper reports on the findings of a preliminary study carried out under the auspices of the Coal Research Laboratories, Department of Energy, Mines and Resources Canada. The objective of this study has been to identify a Longwall face cutting system that is inherently safer than the conventional shearer loaders used in Nova Scotia.

Jan 1, 1985

By Babu R. Yama

Artificial Intelligence research has produced several tools for commercial application. Neural Networks, Fuzzy Logic and Expert Systems are some of the techniques that are widely used today. Artificial Neural Networks (ANNs) are excellent predictive, pattern recognition, and data analysis tools. In the mining industry, ANN techniques are being used commercially for real-time process control applications. Modeling of spatial data, ore reserve estimation, tunnel design, longwall stability prediction, and geologic roof classification are additional application areas in which neural networks have been applied successfully. A standard back-propagation algorithm was used to train a series of neural networks for a real-world predictive task. After training and optimizing the neural network architecture, performance of the network is measured on an independent validation set. Results indicate a correlation coefficient of up to 84 % between the actual and predicted values. A neural network model is developed for learning the spatial continuity of a mineral field and, consequently, for predicting sulfur values given coordinate values. The neural network performed not only satisfactorily, but in some cases performed better than the kriging model.

Jan 1, 1997

By T. Tamagawa

A gaseous chlorination process for hydrometallurgical treatment of a chalcopyrite concentrate was investigated. The overall process is visualized to consist of low temperature chlorination-selective oxidation, followed by aqueous chloride leaching and SX-EW for producing electrolytic copper, elemental sulfur and ferric oxide. In this article, the chlorination phase of the processes is described. Initially, the chlorination behavior of chalcopyrite-concentrate micro-pellets was investigated using a small batch-type fluidized bed reactor. The optimum conditions thereby established was used in continuous chlorination tests. The chlorinated products thus prepared were used in the selective oxidation phase of the investigation.

Jan 1, 1999

By F. Milton Lewis

In 1977 a paper was presented which reviewed the cost trends in producing copper by conventional processes for five years, 1972 through 1976. In this paper these costs have been updated to include the years 1977 and 1978.

Jan 1, 1979