Search Documents

By Walter N. Campbell

The Simon Silver Mine is located near Mina, Nevada, approximately 50 miles northwest of Tonopah and 40 miles east of Hawthorne. It is an old property which was last worked in 1932 and closed operations due to problems arising from low metal prices. Federal Resources Corp. acquired the property in 1963 and undertook a completely new development program since the old surface plant and underground workings were beyond feasible repair. The deposit of silver, lead, zinc and copper is predominantly replacement of limestone. In the summer of 1964, a new surface plant was constructed and on December 2, 1964, sinking of a three compartment vertical shaft started and was completed to a depth of 1088 feet in April of 1965. Following the sinking program an 850 foot crosscut was driven to intersect the mineral zone on the 1000 level after which drifting, crosscutting and raising totaling some additional 4280 feet has been completed along with considerable diamond drilling and long holing into the walls. To date, two ore bodies have been encountered and test stoping operations are underway together with development of the 800 level for servicing, ventilation and access. The present development of ore is directed towards substantiating sufficient reserves to warrant the construction of a flotation mill.

Jan 1, 1967

By M. Z. Rashad

The purpose of this work is to determine the influence of sample length or size on the value of variance (Semivariogram) to select the suitable length that is required to the geostatistical computations of ore evaluation. Three cases in Ghorabi Iron Ore were studied. The first one was on the iron fraction (Fe%) at which the semivariogram gave an evidence to good continuity of the fraction in the ore. In this case, the length of sample has not important influence. The second case was for the Mn% component of the same area where the semivariogram has a nugget effect. The selected length for this case was 4 meters. The Cl% fraction of the ore was the third case where the anisotropic phenomena was appeared and the suitable length is 3 meters.

Jan 1, 1992

By R. L. Loofbourow

Most wet mines face unquantified water costs as well as the obvious wing costs. Both kinds of cost are multiplied by work at greater depth and by higher unit prices. This intensified challenge merits renewed or perhaps altogether new response. Any practicable way to reduce inflow tackles both obvious and unquantified costs. Ten groups of possible ways to do it are cited. Most have been demonstrated. Two are known from work other than mining. Surely new means can be found. Here are opportunities for operators of wet mines!

Jan 1, 1980

By A. K. Kelly

Potash was first discovered in Saskatchewan in 1943 but its continuous extraction did not begin until 1962. In the years since then, potash has played an important role in the economic and political life of the province. And, as is well-known, the most eventful time in the life of the industry occurred in 1975 when the Government of Saskatchewan decided to become a major participant in potash production. To understand that decision, however, requires an understanding of the economic development of Saskatchewan and of relations between the industry and the government prior to 1975. This year, Saskatchewan celebrates its 75th year as a province. For most of those years, we have been an agrarian economy and society, dependent on exports of cereal grains, mostly wheat, for a livelihood. Even today, agriculture accounts for about 25% of the province's Gross Domestic Product (Economic Review, 1979, p. 7) and difficulties in agriculture spread rapidly to the rest of the provincial economy. The difficulties and risks that go hand in hand with being a "one crop" economy were known as long ago as 1920 but were not fully appreciated until the combination of depression and drought in the 1930's turned the prairie grain- belt into a dustbowl. Some idea of the severity of the depression is revealed by the following data: in 1928, Saskatchewan produced 321 million bushels of wheat. By 1931, the total fell to 132 million bushels and, in 1937, to a mere 37 million bushels. The value of agricultural products sold off farms fell from $273,000,000 in 1928 to a meagre $51,000,000 in 1937. The impact of such a fall of agricultural incomes was catastrophic since about 70% of the population of some 921,000 persons lived in rural, agriculture-dependent areas (Britnel.1, 1939, p. 14).

Jan 1, 1980

By M. S. Prasad

This paper presents the process methods of beneficiating various copper-cobalt and copper-zinc ores mined by Gecamines in Zaire. Geology and mineralization of both sedimentary and vein type deposits are described with special emphasis on the production of oxide, dolomitic and sulfide concentrates. Description of different types of concentrators and their treatment methods are discussed for the production of sulfide, oxide and dolomitic concentrates. Production of concentrates, their consumption and stocks are briefly reviewed. Modernization of the concentrators with substantial investments on grinding, classification, flotation methods and tailings treatments are also discussed to improve the metallurgical efficiency of the concentrators with a view to improve the production of concentrates both qualitatively and quantitatively.

Jan 1, 1990

By J. Marbeau

In this paper, a geostatistical study of the North Butte roll type uranium deposit is presented. The geostatistical procedure applied takes into account the varying direction of the roll front for reserves calculations. For variogram calculation, the roll front is unfolded thereby allowing estimation of the variogram in directions parallel to and perpendicular to the roll front. Variograms calculated in unfolded space show strong directional anisotropies consistent with the anticipated configuration of the deposit.

Jan 1, 1991

By T. M. Yegulalp

One of the important factors affecting the determination of the minimum number of increments in a gross sample of coal is the variance component due to segregation. The segregation variance may be estimated by following the ASTM standard procedures. Since the estimate itself is a random variable, it is important to test if the value obtained is due to chance causes. This paper introduces a statistical test, based on the procedures published by ASTM, to test if the segregation variance is significantly greater than zero.

Jan 1, 1986

By D. D. Schlepp

There is a continuing debate about the influence of circulating load and classifier efficiency on the capacity of the circuit. Specifically, the effects of preferential classification, bypassed fines, and the sharpness of classification will be examined. Horizontal cyclones have also proven to be very successful in a number of operations but their impact on the circuit capacity has not been clearly defined.

Jan 1, 1990

By G. R. Doubek

Dual Tube Reverse Circulation (DTRC) drilling has been extensively used for collecting groundwater information for the dewatering program at Amax Gold Inc. Sleeper Mine. This paper presents a discuss ion of the types of data which can be collected from DTRC drilling, as well as the effect submergence has on the data. A simple low-cost method of injection testing has been developed using DTRC equipment, allowing quantitative data to be obtained from exploration or test holes. Potential yields can be determined for each drill location, allowing siting and design of production wells to be optimized.

Jan 1, 1992

By M. C. Roberts

In assessing the future markets for a mineral from a producing district, three key aspects must be considered: 1) the future growth in markets, 2) the competitiveness of the district in terms of production costs and reserve adequacy, and 3) the competition from alternative sources of supply. This paper will focus on the first issue by developing a method of predicting the demand for phosphate from the trends in the major markets for phosphate products, primarily the fertilizer and agricultural markets. The paper will show how broad changes in the final end use markets for phosphate products have evolved over time and how this has affected the needs for phosphate rock. These trends are then projected into the future to make an assessment of future phosphate requirements.

Jan 1, 1998

By J. E. Miller

The development of a new means of measuring the relative abrasivity of a slurry came about by necessity in 1967 during a full scale loop test of a 560 H.P. reciprocating pump handling magnetite slurry. In order to evaluate the life of expendable fluid end parts, the question of the amount of attrition in a re-circulated slurry had to be considered. An expected reduction in abrasivity as a result of this attrition would certainly give erroneous data on a parts life test. There- fore, some means of measuring such change in abrasivity became imperative. Several test methods were investigated1 but it was felt that these did not fully represent the wear due to back and forth rubbing action associated with a reciprocating pump. A "rubbing block" device used some years ago to determine the quality of hard facing materials was recalled, along with its shortcomings, in that an attempt was made to suspend a small percentage of abrasive particles in a colloidal viscous "mud". Erratic results were attributed to the fact that it was difficult to maintain a consistent slurry concentration under the metal wear block and the reciprocating speed was not great enough to maintain good agitation.

Jan 1, 1973

By Valérie J. Bertrand, Richard W. Lawrence, Marcos G. Monroy

Two cemented paste backfill (CPB) formulations containing pyritic tailings were leached in deionized water in flooded and alternating air-flooded environments and in a simulated acid rock drainage-type (ARD) solution. Scanning Electron Microscopy (SEM), solid phase chemistry and acid-base accounting measurements documented the weathering characteristics of the CPB samples. Short-term exposures of the portland-CPB samples preferentially dissolved the cement binder to a greater extent than slag-Portland CPB mistures. In all cases, the added neutralizing potential provided to backfill by cement was short-lived and insufficient to neutralize the acid generating potential of the mixture.

Jan 1, 2000

By R. L. Miller

The potential for recovery of enriched uranium from spent nuclear fuel which has been consolidated into a nuclear waste form was explored in the studies reported here. The waste form of interest is iron-enriched basalt (IEB)--a silicate-based, fused-cast ceramic. IEB samples were prepared containing fuel assembly materials that simulate the core debris of Three Mile Island Unit II;1,2 the nominal composition of the consolidated waste form is given in Table 1. Ore Types The IEB samples, or man-made uranium ores (MMUO), are in two different mineralogical forms. Each MU0 was made by melting the constituent materials and holding at about 1500°C for 1 h. The MMUOs were then heat treated to control crystallization and crystal growth and then cooled to room temperature.

Jan 1, 1983

By R. J. Beckman

This paper traces the history of mica mining in Alabama from 1870-1970. The decline of sheet mica production is noted and emphasis is placed on the more recent activity of scrap mica production and the development of the U. S. Gypsum Co. mica properties in Randolph County, Prospecting for weathered pegmatites of sufficient size to warrant development is a continuing challenge since most deposits are too small and all exhibit varying characteristics as to size, shape, and weathering. Quantity and quality of muscovite mica in the pegmatites is of utmost importance and its recovery during processing of the ore is described.

Jan 1, 1970

By Leslie G. McMillion

A field project to develop and demonstrate a method for alleviating problems of highly-mineralized ground water where they occur as isolated zones or pockets in fresh-water aquifers is being conducted in the Ogallala Aquifer of eastern New Mexico by the Robert S. Kerr Water Research Center. Removal of contaminated water is by a large-capacity well and the pumped poor-quality water is used locally for secondary recovery of oil, Benefits of the operation are threefold in that the aquifer is being reclaimed for future fresh water production, contaminated water is being used beneficially, and fresh water which otherwise would have been used for waterflooding is available for other purposes. Ground-water quality in the site has improved markedly after 21 months of operation. Water quality in 15 specially-drilled monitoring wells has returned to the original quality level of the aquifer, and chloride concen¬trations in the pumping well have dropped to half the maximum level recorded thus far. Project results are very favorable and provide guidelines for initiation of similar undertakings in localities where needed.

Jan 1, 1970

By Robin Adams

After nearly five years of economic hardship, the world copper industry is, in our opinion, about to enter a period of considerable strength. This opinion is based on three main propositions, namely: 1) there are a number of reasons, both general-economic and industry-specific why copper demand is likely to perform significantly, more strongly in the 1980's than in the 1970's; 2) the virtual cessation of investment in new facilities, especially at the mine level, over the past years makes it physically impossible for capacity to expand as fast as demand in the mid-1980's; and 3) there is much less "excess" inventory available than most analysts believe. If we are correct in these assumptions, then the implication is that copper prices will climb up to, and possibly beyond, the cost-justified price level. Combined with general inflation, this suggests a price in excess of $2/pound by 1985 or roughly treble the 1978 average.

Jan 1, 1979

By S. B. Castor

Although production generally satisfies demand for rare earths, new markets may make undeveloped resources, particularly those rich in yttrium, more interesting. A Precambrian carbonalite orebody at Mountain Pass, California, has been the world's largest rare earth producer. Minor rare earth production comes from titanium placer mining in Florida and uranium mining in Canada. Prior to operations at Mountain Pass, North American production was mostly from placer deposits that constitute large, low-grade rare earth resources. Newly discovered North American rare metal resources in peralkaline igneous rocks are potential yttrium producers. Most of these resources are in a continent-wide belt of anorogenic magmatic rocks approximately coeval with mineralization at Mountain Pass. Other untapped rare each resources in North America are generally light rare earth-dominated and small or of low grade.

Jan 1, 1991

The adsorption of gold onto activated carbon in iodide solutions has been studied. The adsorption rates were determined as a function of temperature, salt concentration and pH as well as activated carbon concentration. A kinetic model was also developed for the adsorption. The adsorption rate was believed to be controlled by a mixed mechanism of film diffusion and pore diffusion, but the film diffusion had a major contribution to the overall rate. Experimental findings were in good agreement with the model developed. The apparent activation energy was found to be 14.9 kJ/mol.

Jan 1, 1993

By Steven W. Hunt

"A paper called “Global Experience with Soft Ground and Weak Rock Tunneling under Very High Groundwater Heads” was presented at the North American Tunneling 2006 conference (Holzhäuser et.al 2006). It summarized global experience with earth pressure balance (EPB) and slurry shield tunneling on nine projects that encountered groundwater heads ranging from 6 to 11 bar. Since then, additional projects have been completed with groundwater heads ranging from 7 to 15 bar. Of these, the high pressure tunneling experience on the Lake Mead Intake No. 3 project in Nevada and on the Eurasia Tunnel (Istanbul Strait Crossing) had the greatest lengths of tunneling at face pressure over 7 bar. Experience with sustained pressurized face tunneling at groundwater heads over 7 bar and risk management observations are the focus of this paper. INTRODUCTION High groundwater head, particularly at 7 bar or more, is a major challenge when tunnelling in high permeability ground and on drives long enough to require cutter changes. It has a strong impact on design and operation of Tunnel Boring Machines (TBMs) in order to protect the main bearing from contamination, prevent excessive groundwater inflow, ensure face stability and enable access to the cutterhead and excavation chamber for maintenance. During the past 20 years, TBM manufacturers and suppliers have made tremendous improvements that allow tunneling at groundwater pressures to 17 bar or more. The most significant risk with high pressure tunneling is generally that of excavation chamber access and potentially the cutterhead for cutter changes, cutterhead repairs and TBM maintenance. Hyperbaric interventions are possible and safety variances have been approved for saturation dive interventions at pressures as high as 17 bar (Lake Mead Intake No. 3). While high pressure hyperbaric intervention equipment is available and safety approvals can be obtained at many locations, few contractors consider the cost and risk of hyperbaric interventions over 7 bar to be acceptable as the primary means of excavation chamber access. Experience with high pressure tunneling prior to 2006 was summarized in a paper entitled “Global Experience with Soft Ground and Weak Rock Tunneling under Very High Groundwater Heads” (Holzhäuser et.al 2006). That paper provided information on 9 projects: South Bay Ocean Outfall, San Diego; Channel Tunnel (French Side), France; Storebaelt Tunnel, Denmark; 4th Elbe Tunnel, Germany; Wesertunnel, Germany; Westerschelde Tunnel, Netherlands; St. Petersburg Red Line, Russia; Nara Prefecture Water Conveyance Tunnel, Japan; and Tokyo Wan Aqua Line Tunnel, Japan – see Table 1."

Jan 1, 2016

By M. Z. Rashad

The purpose of this paper was to compare the covariance and multiquadric functions in same mining and geological applications. The basic principals of the two techniques are covered briefly. Similarities and dissimilarities of the covariance and multiquadric functions are discussed geometrically, mathematically and practically. A 14 by 16 kilometer square area in Baharia Oasis, Western Desert of Egypt, was selected for a detailed comparative test. The gravity anomalies of forty-eight test stations were computed by using the data of sixty-three control stations. The results indicated that the covariance function is quite better than the multiquadric one. On the other hand, the multiquadric function more simple in computation than the other one, which needs to precalculations such as semivariogram and covariogram. Moreover, multiquadric equations are based on geometrical and physical considerations rather than covariance functions.

Jan 1, 1990