Search Documents

By Haydn H. Murray

Kaolins and bentonites of economic importance in Australia and New Zealand are described. Clays that are used for structural clay products are not discussed. Residual, hydrothermal, and sedimentary kaolins are utilized including clays associated with coal measures. Bentonites are sedimentary and residual. Very little kaolin and no bentonite is exported presently, but this will change in the near future as transportation costs continue to escalate. Many areas of Australia, in particular, where kaolins are known to occur have not been investigated to determine the quality and quantity of the deposit.

Jan 1, 1982

By D. S. Choi

Underground production of coal by longwall methods has increased significantly in the last few years and will very likely continue to: increase. There are several reasons for this. First, as mining moves into seams having greater overburden, roof exposure must be reduced since support will become' increasingly expensive. Secondly, the growing demand for coal has forced the coal industry to seek alternative, more productive, coal mining methods. In addition, the longwall method greatly simplifies the underground ventilation network. This paper addresses itself to the design of longwall development headings, particularly to those of the United States where multiple development headings are required by law. The most burdensome problem encountered in many longwall mining installations is deterioration of the tailgate due to the combined effect from, the active longwall gob and the old gob made by mining the previous panel.1 Portions of the tailgate entry are sometimes closed to such a degree that extensive repair work is necessary to keep the entry in usable condition. The purpose of this paper is to present the result of a study in progress which combines field measurements with numerical model analysis to reduce the cost of maintaining tailgate entries in longwall mining systems.

Jan 1, 1975

By B. Hagemeyer

The trend to higher solids paper coating and to neutral/alkaline papermaking is causing an above average growth in the use of calcium carbonate as both a paper coating and a paper filling pigment. These developments are expected to continue well into the 1990s. Thus, calcium carbonate will account for a somewhat larger percentage of total paper pigment volume. Nevertheless, overall growth in paper tonnage coupled with an increase in filler pigment percentages will create a demand for larger quantities of other pigments as well. Kaolin will continue to be the dominant paper pigment by far, with continued growth though at a somewhat slower rate than calcium carbonate.

Jan 1, 1986

By C. D. Atkinson

The past few years have seen a much greater concern about air pollution in this country. This concern has led to increased legislation restricting the discharge of many substances such as sulfur dioxide and particulate matter to the atmosphere. In the future, it is anticipated the present permissible emission levels will be lowered. Current and impending restrictions on the emission of sulfur dioxide have brought out the fact that there is a shortage of available low-sulfur fuel for power plants and industrial use which promises to have an economic impact on the nation's energy picture (1) The Pittsburg & Midway Coal Mining Co., under the sponsorship of the Office of Coal Research, has developed a process to produce a fuel capable of meeting the energy requirements of this nation (2) The process is called "The Pittsburg & Midway Solvent Refined Coal Process". The principle product from the process is Solvent Refined Coal which is an ashless, low-sulfur fuel with 16,000 BTU per pound regardless of the rank coal from which it is produced. The product can be burned as either a solid or a liquid fuel. The process appears to be economically more attractive than other methods of alleviating the pollution problems of this nation. In addition to reducing the air pollution caused by stack gases, the product produced is potentially useful as a source of electrode coke and electrode binder pitch, as a gas turbine fuel, in the production of metallurigical coke and pavement asphalt, and as the first step in the overall process to produce distillate fuels and pipeline gas (3).

Jan 1, 1973

By William R. Yernberg

Caterpillar introduced 21 new products during Caterpillar Press Days ‘96, held in June at the company’s proving grounds near Tucson, AZ. The event, billed as the largest product introduction ever held by Caterpillar, was attended by press from around the world. Most of the new products were demonstrated at Caterpillar’s Tinaja Hills Training Center in the Sierrita Mountains south of Tucson. Under the scorching Sonora Desert sun, the press was treated to demonstrations of the new equipment. After a display of the equipment’s power and capabilities, the press was given an opportunity to operate the new models and, in some cases, compare them with the old.

Jan 1, 1996

By . A. J. Erickson

The Park City District, one of three major mining districts in Utah, is located approximately 20 miles southeast of Salt Lake City on the eastern slope of the Wasatch Mountains. The district has been in near continuous production since 1869. Production has been sustained from exceptionally long bedded replacement ore bodies in the Thaynes, Park City, and Humbug formations and also from several major veins. District production is summarized below. TABLE NO. 1 Park City District, Total Production, 1869 thru 1968 (Source r Various Company Records) [ ]

Jan 1, 1970

By Hans-Henrik Wallin

The stresses in the heads and shell of a grinding mill are largely dependent on the bending moment produced by the trunnion bearing. By using spherical roller bearings in a special narrow housing a short moment arm is obtained and the bending moment is reduced. For large mills a hydrostatic shoe bearing which also gives a short arm, can be used. Spherical roller bearings also require less maintenance and have a long service life. As the bearings are grease lubricated an automatic lubricator is used instead of an oil lube system. Service data from two Swedish mining companys confirm the fact that the above arrangements provide a long service life.

Jan 1, 1979

By Rudolf Fahn

Bentonites are best suited for the preparation of acid activated clays with efficient adsorption properties. They are weathering products of acid volcanic ashes and their natural deposits are world-wide spread. The main constituent of bentonite is the aluminium hydrosilicate nontmorillonite with a high ability to swell. Süd-Chemie owns bentonite deposits in Germany and subsidiaries in Italy, Mexico and Arizona.

Jan 1, 1979

By G. C. Hambleton

There is sufficient indication of the existence of a basic misconception in the Coal Mining industry (on a world-wide basis) as to what computer control really does, what it costs, how it works and how and what it achieves as to make this presentation a welcome opportunity to present the case in what we hope is a simple, meaningful way. A plant cannot be said to be "automated" unless the control system has the capability to react automatically in accordance with predetermined programs under a great multiplicity of operational situations.

Jan 1, 1981

By M. G. Ayat

Although other methods of mineral concentration have been developed over the years, gravity separation remains one of the most efficient and economical for cleaning coal. The concentrating table and the spiral separator are popular devices used for the separation of minerals by exploiting the differences in specific gravities of the product material and the gangue. While the former device has been servicing the coal industry for over 75 years, the latter seems to have not been employed extensively for coal cleaning purposes in this country. As far as coal preparation is concerned, both separatory devices seem to be most efficient for intermediate to fine size fractions. As it stands there exists a great deal of confusion amongst preparation engineers and plant managers as to whether spirals can have a place in the coal industry. If so, whether their come back is the beginning of the end for concentrating tables, or can they be employed along with concentrating tables to contribute toward more efficient cleaning processes resulting in an improvement in the overall economics of the coal preparation industry. This paper examines the efficiency of both systems for coal processing operations as well as the basic principles, operational variables, economics, advantages and disadvantages associated with each unit operation. Attempts have been made to draw conclusions and make recommendations as to which system would be more beneficial for coals of known characteristics.

Jan 1, 1986

By R. J. Mirville

Flocculation is an important step in the treatment of coal preparation waste waters. The effects of polymer charge and molecular weight and solution pH and ionic strength on the adsorption and flocculation characteristics of a series of polymeric flocculants on some typical waste water constituents have been studied experimentally. The results indicate that the nature and extent of flocculation are strongly system-dependent. For the case of coal, both adsorption and flocculation behavior can be correlated with the polymer conformation in solution. For the mineral constituents, on the other hand, adsorption and flocculation depend also on the surface properties of the solid.

Jan 1, 1979

By J. C. Haptonstall

Stoping methods at the Homestake Gold Mine through 1978 had been traditional overhand cut-and-fill, shrinkage or square set. High costs, low-productivity and safety concerns prompted the mine to search for and adopt a "bulk mining" technique as a primary stoping method. Blasthole stoping had been successful but it is very development intensive, and was not suitable for the mine's accelerated mining program. Vertical Crater Retreat stoping was selected, and today accounts for over 50% of ore production. Case histories representing both the successes and failures of VCR stoping in the mine are discussed.

Jan 1, 1986

By R. L. Atwood

This paper discusses the metallurgical and Manufacturing input to Merrill-Crowe plants. Topics treated are pregnant solution chemistry, clarification, degassing, zinc addition, product filtration, accounting, and costs.

Jan 1, 1985

By I. E. Perera

Experiments were conducted to evaluate the response characteristics of commercially available gas, smoke, and flame sensors to fires of common combustible mine materials. The experiments were conducted in the large-scale Fire gallery located at the National Institute for Occupational Safety and Health (NIOSH) Lake Lynn Laboratory (LLL) in Fairchance, PA, using Ponderosa Pine, Red Oak, Douglas-fir, high and low volatile coals, PVC and SBR conveyor belt, No. 2 diesel fuel, and diesel exhaust. All the experiments (except those using No. 2 diesel fuel and the diesel exhaust tests) were conducted in a similar manner, with combustible materials heated rapidly by electrical strip heaters producing smoldering fires that quickly transitioned into flaming fires. The sensors included a diffusion-type carbon monoxide (CO) sensor, photoelectric- and ionization-type smoke sensors, a video smoke/flame detector, and an optical flame detector. Simultaneous measurements were obtained for average gas concentrations, smoke mass concentrations, and smoke optical densities in order to quantify the levels of combustion products at the alert and alarm times of the sensors. Because the required sensor alarm levels are 10 ppm and 0.044 m-1 optical density for CO and smoke sensors, respectively, the different sensor alarms are compared to the time at which the CO and smoke reached these alarm levels (1). In addition, the potential impact of using smoke sensors that have met the performance standards from accredited testing laboratories is also evaluated using the response of an Underwriters? Laboratory (UL)-approved combination photoelectric/ionization smoke detector. The results are discussed relative to fire sensor needs that can have a positive impact on mine fire safety.

Jan 1, 2012

By F. H. Mertens

The costs of an open-pit operation can be classified according to the following hierarchy : -overall cost of production (per ton of ore) -costs of basic operations and functions -costs of auxiliary operations -costs of machines and equipment -maintenance costs. Production cost is a measure of the open-pit mine performance and should be the final target of the management control. It is also a measure of the share of the mine in the processing stages.

Jan 1, 1990

By Victor Phillips

The Humphrey Preparation Plant of Christopher Coal Company, located in Monongalia County, West Virginia, was built to process the combined production of the Pursglove No. 15 and the Humphrey No. 7 Mines. Both Mines operate in the Pittsburgh Seam, primarily producing Metallurgical Fuel destined for by-product ovens in the Pittsburgh District. The results of an extensive core-drilling program have established sufficient reserves of low-sulfur coal to justify a 20,000 ton-per-day preparation plant, This is the story of the preparation phase of this combined operation. Christopher Coal Company operated the Pursglove No. 15 Mine to produce steam coal, which was prepared in a conven-

Jan 1, 1958

By Martin Valeri

The operation described in-this paper will be confined to the Nemacolin Mine of The Buckeye Coal company, Nemacolin, Pennsylvania.' This mine is-located on the Monongahela River approximately sixty miles south of Pittsburgh. The mining is in the Pittsburgh seam that has an average thickness of 88 to 90 inches. The current practice is to mine approximately 80 inches, leaving 8 to 10 inches of roof coal. All of the coal produced is used solely for by-product coking by the parent Youngstown Sheet & Tube Company, Youngstown, Ohio. Eight to ten inches of top coal are left by the miners to prevent air slacking of the draw slate. In addition, this top coal which will float at the washing gravity has a very high ash and sulphur content, and when mined, seriously affects the quality of the clean coal product.

Jan 1, 1961

By John M. Karpinski

A method and equipment have been developed Tor measuring the impact strength of grains of brittle materials. It is shown that brittle materials develop a characteristic particle size distribution when fractured by impact. A simple mathematical model has been found to describe this distribution, and one of the parameters of the model has been designated the r value. The r value is directly proportional .to impact energy and, for fixed impact energy, it becomes a useful criterion of grain strength. Data are presented on the variation of the r value as a function of sample history, initial size, energy input and number of impacts, The results are interpreted in terms of the flaw theory of brittle fracture.

Jan 1, 1964

By Carl F. Austin

The subject of strata control in mining can be approached from both static or loading concepts or from dynamic or impulsive loading concepts. The fracture process itself appears to be primarily a dynamic process as is the gross creation of fractures through the use of impact, stress wave passage or in more general terms, the use of explosives. This paper presents experimental results which indicate that the understanding of the fracture behavior of rock that has been, established in the open literature is not always appropriate. In particular, the results of this experimental program have shown very interesting differences between the formation of fractures in rock and the formation of fractures in other materials such as metals and plastics which are often used as models for rock behavior studies Fracture patterns and causes of dynamic fracturing in various rock and artificial materials are presented.

Jan 1, 1965

By Morton Handelman

The extraction of aluminum oxide_ from its ore is the initial step in the commerical production of metallic aluminum. This is most commonly done by the Bayer Process in which a caustic solution is used to dissolve hydrated alumina from the insoluable materials with which it is associate in bauxite. At the two-thousand ton per day Sherwin Alumina Plant of Reynolds Metals Company, the extraction residue from Caribbean ores is removed from the main pro¬cess stream as the underflow of a continuous clarifier-thickener operation. This sludge, prior to its ultimate r4jection from the process, is washed in a nine-step continuous countercurrent decantation system to recover physically-entrained mother liquor. Control of alumina production costs requires the optimum recovery of solubles from this residue which is generated at the same rate as the finished product. The equipment, operating techniques, controls and process variables which affect the efficiency of this soda recovery from Bayer Process red mud will be discussed.

Jan 1, 1959