Search Documents

By S. Rupprecht

"INTRODUCTION This paper addresses the prevalence of poor public reporting practices of Coal Exploration Results, Coal Resources and Coal Reserves in southern Africa. Currently, the reporting of coal tonnage without supporting coal qualities or “saleable” tonnes and quality is a poor reporting practice that occurs far too often. Not all coal is equal – therefore it is extremely important that investors or potential investors are provided with the full details of both run-of-mine (“ROM”) and Saleable coal tonnage, their associated qualities and other material and relevant information. Competent or Qualified Persons should note that publicly reported information should be sufficient to enable an informed reader to make a reasonable and balanced assessment of the significance of the information provide. “Companies are encouraged to provide information in their Public Reports, which is as comprehensive as possible” (CRIRSCO, 2013): too often this isn’t the case and material matters are either not reported or inadequately disclosed. According to the South African National Standard (SANS) 10320:2014 draft document - “tonnage and coal quality that will be available for sale, either in the raw ROM state (raw Saleable) at a specified moisture content, or after beneficiation of the ROM coal by processing operations to produce materials at specified qualities, size ranges and moisture contents. The assessments must demonstrate that at the time of reporting, the marketing of the products is reasonably justified. The basis of the predicted practical product yield to achieve the Saleable Coal Reserve must be stated. The moisture basis of reporting shall be stated.” As an example to why coal qualities are so important to the public, the requirements of South Africa’s electric public utility (Eskom) power stations are highlighted. The Kendal power station, commissioned in 1988, operates at a Calorific Value (“CV”) range of 19 to 20MJ/kg, an Ash content between 29 and 34% and Volatiles between 20 to 21%. Other power stations, such as Kriel or Hendrina, may require different qualities such as a CV range of 22 to 23MJ/kg, an Ash content between 20 and 28% and Volatiles between 22 to 23%. Thus, in terms of domestic saleable coal, it isn’t just about reporting the coal qualities but also informing the investor as to which power station the coal is intended to be sold as “boilers are designed to burn particular qualities of coal” and “it is not always possible to transfer coal between stations because of different quality requirements at each station” (Chetty, 2010). Sulphur content is also another important quality with the ideal coal content having a quality of less than 1% Sulphur."

Jan 1, 2018

By Ihsan Berk Tulu, Haochen Zhao, Deniz Tuncay

The process of designing pillars and selecting support measures in underground coal mines relies highly on the accurate assessment of mining-induced loads and the load-bearing capacities of the supports. This study proposes a new method to estimate the percentage of load carried by the gob in underground coal mines using a new parameter that introduces the site-specific overburden geology.

Jun 1, 2023

Never known as a conference to shy away from its share of off-color jokes, the Colorado Mineral Processing Division?s Annual Meeting returned to the Broadmoor Hotel in Colorado Springs, CO April 26-28 for its 62nd edition, this one held under the theme ?Does size matter (is bigger always better).? With the predictable jokes sprinkled in here and there, and a few unpredictable ones as well, the three-day conference featured a healthy mix of talks about some of the latest technical developments in the field of mineral processing, as well as insightful looks at some new operations in the western United States. This year, the Colorado MPD also launched the Wagner Equipment Student Scholarship program.

Jan 1, 2012

By R. K. Singhal

The underground coal mining systems have kept pace with the developments that have occurred in other types of mining industry. A diversified group of machines with high horsepower motors, built-in microprocessor technology and with numerous options to satisfy the miners need in a varying geological environment are now available. A brief review of this existing technology and its likely status within the next 21 years is presented. Discussed also are some of the on-going advanced developments in electronic mechanization, remote control and automation together with mine wide data monitoring and management systems and facilities to process and transmit data to remote computerized stations.

Jan 1, 1989

By Jeff Mattern

"Slope performance monitoring, dependable operational practices and ongoing collection of geologic data in openpit slopes all provide valuable information for quantifying potential steepening of subsequent slopes. Mining at the Goldstrike openpit has been ongoing since the early 1980s, having its share of slope instabilities. In areas where slopes have remained stable, consideration has been made for potential slope steepening of final walls.While technology can be efficient, interesting for collecting needed data, slope design fundamentals based on that data can be applied to create much added value.With the proper available equipment, steepening of bench face angles via presplit blasting is not an uncommon method for steepening of interramp slope angles. As an alternative at Goldstrike, the commonly used Modified Ritchie Criteria for empirical catch bench width has been adjusted, resulting in quantified, rock-specific formulas for bench width and rock fall berm placement. The result is an inter-ramp slope angle increase of 2° on a 305- m (1,000-ft) high slope, without the necessary purchases and procedural changes that would be required for presplit drilling and blasting. The result has shown significant net benefits through reduction in mined waste tons and an increase in gold reserves.LocationThe Goldstrike openpit is located in the Great Basin, on the northern end of the Carlin Trend gold belt in northeastern Nevada (Fig. 1). The mine has produced more than 1.2 kt (43 million oz) of gold during the past 30 years."

Dec 1, 2018

By A. J. Getz

Major precious metals projects are underway in Australia, Papua New Guinea, Indonesia, the Philippines and New Zealand. This article reviews the status of those projects. Included in this review are project location, reserves, method of resource exploitation, anticipated production, and other unique conditions. The article is limited to major precious metals projects in the Western Pacific region. This is not meant to negate the attractiveness or importance of the many other projects in that area. The geographical setting of these five countries are shown in [Fig. 1]. The gold output of the countries has increased dramatically during the 1980s. [Table 1] compares 1980 and 1988 production figures. The compound growth rate is 120%. That reflects the attractiveness of the region’s resource base as well as the impact of price increases, new exploration models and processing technologies, and changes in government policies. If the 10 projects discussed here are all brought onstream, their combined output - at about 130 t (4.17 million oz) - would amount to an increase of greater than 50% over 1988 production from this region. Table 2 shows indicative production levels for each of the 10 projects. Dollar amounts are in US currency unless otherwise specified. Australian dollars have been converted to US dollars at the rate of 1.28: 1.00.

Jan 1, 1990

By K. Taniguchi, Y. Inada

When underground openings are excavated in rock mass for storage of Liquefied Natural Gas, hereinafter referred to as L.N.G., as its temperature is -162o C, steep temperature gradients and thermal stress occur around the openings. That is, the plastic zone and cracks around openings will expand with time. In this paper, the range of cracks which were obtained by the Crack Analysis Method and the range of the plastic zone which was obtained by the No Tension Analysis Method were investigated and compared.

Jan 1, 1986

By Georgene Renner, Chee Theng, William Gleason

"More than 6,300 people attended SME’s 2016 Annual Conference & Expo in Phoenix, AZ and many of them made the trip to the conference to take part in the excellent technical sessions that are presented on a yearly basis by the Society.Holding true to form, this year’s conference was full of options. In fact, this year there were 121 technical sessions and 751 presentations to chose from. The following is a sample of some of the technical sessions as seen through the eyes of the editors of Mining Engineering and SME technical papers.SME Sections Sharing Success: Changing thePublic Perception of MiningThis session was a workshop on how several local sections were effective in getting the message out to their communities and schools about the value of the extractive minerals industry. Several sections shared their outreach successes, including the Mining in Society merit badge activities by the Minnesota Section by Julie Lucas and SME’s participation in the World Scout Jamboree in Japan by Frank McAllister.Dan Alexander highlighted activities by the Pittsburgh Section, such as preparing minerals kits and pamphlets for elementary school classes and regional science fairs. The West Virginia University Student Chapter used the kits as handouts at their local gem and mineral show. School speakers in full mining gear were especially interesting to the young children.Other speakers were Michael Linn, Paradise Valley Unified School District — Business and School Partnerships; and Greg Kruse, Central Wyoming Section of SME — What makes a successful section?Engineering Competency ModelAmerican Association of Engineering Societies and the U.S. Department of Labor, with a grant from the United Engineering Foundation, developed a guide to the set of skills necessary for success in the engineering community -- Knowledge – Skills – Abilities — needed for all disciplines.Various engineering societies are now writing the Tier 5 occupation-specific requirements. The Competency Committee is charged to write concise and discipline-specific mining engineering, mineral processing engineering, geological engineering, and geophysical engineering by Sept. 30, 2017."

May 1, 2016

When it comes to safety in the mining and extractive industries, success is literally a matter of life and death. Anything short of perfection is not acceptable. In recent years, the mining industry in the United States has made tremendous strides in terms of health and safety for its workers. Part of that success has come with an increased focus on the issues of safety, an intense examination of procedures, liberal sharing of best practices and a focus on the synergy between safety, reliability and environment. During his closing keynote address of the Safety Management & System Reliability Conference in Minneapolis, MN on Nov. 15, Joe Driscoll, vice president of Great Basin Gold, showed a calendar from the coal fields in Pennsylvania from the early 1900s. The calendar marked the number of mine-related deaths each month. Some months, the number was as high as 50. It was an illustration of how far things have come, but there is still much more work to be done.

Jan 1, 2013

By Gino Vogt

In mechanized tunnelling operations, performance, consumption and safety are main factors for jobsites. One of the most important components effecting these factors, especially in slurry TBM operations, are Slurry Treatment Plants (STPs). Inadequately dimensioned and designed STPs create bottlenecks for tunnelling operation and jeopardize time schedules and performance. Inefficiently planned STPs could drastically increase consumption figures such as electrical power, bentonite, water polymers, etc. Inaccurately selected and treated suspension properties can cause a high-risk potential for the whole project. This paper debates the relevant key parameters for STPs from start to finish of a project and its results in influencing factors from the manufacturer’s point of view.

Dec 1, 2022

By Sharon Thomson

Since 1977, Amax Coal Co.'s Belle Ayr mine near Gillette, WY, has been the largest producing coal mine in the US. In its 10 years of operation more than 90 Mt (100 million st) of coal have been shipped from the mine's facilities to electric generating plants across the country. It is thought to be the largest amount ever produced in US history from a single coal mine. The railroad is Belle Ayr's lifeline for moving this massive volume from a relatively isolated corner of northeastern Wyoming. There are no waterways for barge traffic, and highway truck hauling would be impractical considering the quantity and distance of coal to be moved. Transportation in the Powder River Basin-at least for the present-is strictly unit trains. An average of four unit trains daily load at Belle Ayr. These trains average 108 cars long, with a capacity of 91 t (100 st) per car. Burlington Northern Railroad serves the Powder River Basin, but locomotives supplied by Union Pacific, Milwaukee Road, and Kansas City Southern are a common site as well, since coal will often travel these lines too on its way to utility plants in Colorado, Kansas, Iowa, Texas, Arkansas, Louisiana, Wisconsin, and Oregon. When Belle Ayr opened transportation in the Powder River Basin was in an early development stage. As the first large-scale coal shipper in the area, Belle Ayr was the only user of a 27-km (17-mile) railroad spur south of Gillette. Other mines, however, were to open soon on the abundant, low-sulfur reserves. Today, less than a decade after Belle Ayr's debut, 13 large-capacity mines operate near Gillette. The 27-km (17-mile) spur that once served only Belle Ayr has been extended 177 km (110 miles) south to service other mines as well, and to tie into a major rail line in central Wyoming. The Powder River Basin is now served by a wishbone-shaped track configuration that allows train movement north into Montana, south into Colorado, and east into Nebraska for connections across the country. Operations at Belle Ayr are closely tied to train arrivals and departures, with coordination essential between mine operations and rail personnel. "Train movement in the Powder River Basin has evolved to the point where we are fine-tuning mining operations to coordinate them with a more dependable transportation system," according to Joe Jefferson, transportation supervisor with Amax Coal's western division. That, however, hasn't always

Jan 10, 1982

By B. Slaker, M. M. Sears, G. Rashed

Ground falls represent a significant hazard at underground mines in the stone, sand and gravel (SSG) sector in the United States. Researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) are conducting detailed investigations into the complex loading conditions at underground stone mines operating in challenging conditions. This paper presents the application of numerical modeling to analyze pillar and roof stability at a dipping underground limestone mine.

By Robin Dill, Julian Prada, Kathryn Kelly, Brian Hann, Todd Moline

Narragansett Bay Commission’s (NBC) Pawtucket Tunnel Project includes construction of the 11,600-ft long, 30-ft ID, deep rock tunnel. This paper presents insight into the features and benefits of lump-sum, design-build that led NBC to select it as the project delivery method. The use of a design-build contracting process that included proprietary meetings to discuss and obtain feedback on Alternative Technical Concepts as well as to facilitate reaching consensus on modifications to the GBR-B is also described. The discussion includes features and benefits of design-build process that not only addressed NBC’s desired outcomes, but also allowed the Design-Builder to propose several innovative changes to the Base Technical Concepts included in the bid documents, and to develop a GBR-C that was compatible with their proposed means and methods of construction and addressed what they believed to be the more significant subsurface risks on the project.

Jun 13, 2023

By Timothy G. Shuttleworth

In the late1970s, mineral processing plants producing copper sulfide concentrates and oxide leaching feedstocks went online with operating tonnages that exceeded traditional installations. This created a need for larger capacity belt conveyors and apron feeders. Apron feeders are slow moving, heavily loaded conveyors that feed a deep bed of ore from a bulk holding location (a bunker) as a controlled stream, often into a large capacity crusher. Apron feeders use sprockets and caterpillars, while belt feeders use rubber belts with motorized head pulleys to convey the material. The damaging of belts and clogging of transfer points from tramp iron required larger magnetic separators and the removal of tramp metal cannot prevent these serious problems. Corrective action at this location is important for two reasons: Removing tramp iron early in the ore stream protects downstream equipment from potential costly damage. Installing apron feeder magnets before the primary large capacity crusher means that secondary and tertiary crushing steps (made up of multiple parallel units) operate more efficiently, since tramp metal is removed at the onset.

Jan 1, 2011

By Samer Sadek, Phoebe Cheng, Changmo Kwon, Myat Ohn

BART Facilities Standards (BFS) Structural Criteria is a living document that governs planning, design, and construction of all BART projects. Since its development, the document undergoes incremental changes and updates to reflect policy changes, changes in local, State, or national design codes and guidelines, advancements in engineering and technology, or based on the performance of past built infrastructure. In 2020, the BFS-Structural Criteria underwent a comprehensive update and was released with BFS version 3.2. This paper summarizes the updates to the Tunnels and Underground Structures Section of the Structural Criteria, and provides insights to the basis and logic of the requirements.

Dec 1, 2022

By Philip-Mark Spanidis, Christos Roumpos, Francis Pavloudakis

This paper presents a quantitative research (QNR) methodology, collaboratively conducted with a group of mining experts, to assess the knowledge management (KM) landscape in the Greek mining industry. The methodology involves a framework for structured data collection using questionnaires, statistical analysis, discussion on critical methodological aspects, and interpretation of results focusing on key aspects of interest for designers of KM systems. The paper concludes by summarizing the methodology’s outcome and proposing perspectives for further research.

Aug 1, 2024

By Shinichi Konda, Gary Nishimura

"Thousands of years ago large glaciers carved much of the landscape in Puget Sound, depositing abrasive and granular soils including cobbles and boulders along with layers of clay and sand. Tunneling in this geology – common throughout much of the northern and Midwestern U.S. – is challenging and can be unpredictable. The use of pressurized face tunneling, most commonly with EPBs and slurry type machines, has made excavation in this geology more efficient, but difficulties still remain. Through analysis of recent projects in Seattle, Washington, USA, the authors draw conclusions as to the best TBM designs and operational parameters for this variable, abrasive and often difficult ground. Performance data is analyzed with an eye towards advancements that could further improve TBM tunneling in glacially deposited soils. INTRODUCTION Over the past several ice ages, extensive glaciers reaching across much of North America transported large amounts of soil and rock as they moved across the land. The substantial weight of the ice sheets mixed together a wide range of soil types along with a variety of rocks and boulders of all sizes. Many rock formations were reduced to pebbles or particles containing highly abrasive characteristics. Any boulders able to survive were generally comprised of harder materials which were scattered throughout the soil. This highly variable mixture of abrasive soils and high strength boulders can be found in many areas across the Puget Sound and other regions of the country. Wherever they are encountered, they often create a difficult and unpredictable mining environment for both equipment design and operation. Modern TBMs are optimized early in the design process for specific types of geology, and unexpected conditions can require extensive modifications. In addition, several operational parameters need to be adjusted to balance ground characteristics, and advance rates can be significantly affected in mixed and rapidly changing soil conditions. Both EPB and slurry machines can be used successfully in these conditions, provided their respective operating criteria are met. Ideally, an EPB is operated with a relatively thick muck consistency, which accommodates moderate changes in soil permeability and maintains a reliable pressure differential through the screw conveyor. However, this also causes higher wear on rotating components and requires more energy at the cutterhead. Alternatively, slurry machines typically operate best with a more fluid muck consistency that can be easily pumped through the extensive piping system. This tends to reduce the wear on the cutterhead and the power requirements of the cutterhead drive system, but also makes the machine more sensitive to changing soil conditions. Generally, the slurry piping system is also more capable of controlling high face pressures, although the screw conveyor of an EPB can also be designed to accommodate most high-pressure conditions."

Jan 1, 2016

The Mine Safety and Health Administration (MSHA) academy in Beckley, WV, received enquiries from various segments of the mining industry concerning alcohol and substance abuse in the mining industry. The MSHA Director formed a committee, the Mining Industry Committee on Substance Abuse (MICSA), to deal with these enquiries. The committee met in April 1985 at the mining academy in Beckley. The MICSA committee expanded its membership to represent labor, management, and government agencies affiliated with the mining industry as well as government agencies dealing with alcohol and drug abuse. This expanded 18-member committee met for the first time in July 1985. At that time, two cochairmen were elected, one from labor and one from management. MICSA has spent time on education by sharing information on the issues and by calling in outside experts for advice and consultation. The committee also initiated several projects. These include a resource manual on substance abuse and employee assistance programs. Mine operators and labor unions can use these programs as guides. MICSA is also assembling statistics on substance abuse, particularly as applied to mining. And the committee commissioned an Education film, Substance Abuse, Is It Our Problem? (The results of a survey on drug use, given in Table 1, suggest that substance abuse may indeed be a problem.) The educational film, produced by MSHA, is an introduction to the problem of substance abuse in the mining environment. The film encourages mine operators, labor unions, and miners to analyze their individual circumstances to determine whether a problem exists. The film also offers ways to deal with the problem. And the film invites the mining industry to request additional information from MICSA. There is no single approach to substance abuse that will fit the need of every mining operation. As with any health, safety, or production problem, remedies must be site specific. MICSA's aim is to channel ideas to those who seek to help employees in a mining environment who seek to rid themselves of alcohol and substance abuse. As stated more formally: The Mining Industry Committee on Substance Abuse represents the efforts of labor, management, and government. The mission of the committee is to make the mining industry aware of the problems resulting from alcohol and other drug abuse and to recommend possible methods to remedy the problem. The function of the committee is to assist the industry in developing programs and resources to recognize and provide help for troubled employees, and thus reduce the risk of accidents, while lower absenteeism and increasing productivity.

Jan 11, 1987

By Lawrence R. Molsather

Certain hydrologic parameters are affected by development of a mine. These include the area, yield, and storage in a watershed. Alteration of these parameters results in variations in lake levels and stream flow rates and in changes in ground water elevations and gradients. These factors have become increasingly important in light of present environmental design standards and government regulations. Mitigation of adverse hydrologic impacts can be costly and can create operating constraints which complicate the mining process.

Jan 1, 1980

By Jeff W. Butwell

Mill flotation tailings impounded at the Gooseberry Mine site between 1976 and 1984 were determined to be an economic source of gold and silver. The tailings would be recoverable by standard heap leach technology in conjunction with feed agglomeration. Metal recovery at 85% gold and 75% silver is attained on properly agglomerated (pelletized) tailings that average 85% -75 µm (-200 mesh). The impounded tailings averaged more than 18% moisture (32% moisture maximum at depth) in place behind the storage dam. Therefore, the mining method, mixing and agglomeration technique, and materials handling practice were major considerations in making this operation a financial success. The Gooseberry Tailings Project is located about 35 km (22 miles) east of Sparks, NV. The project is owned by Asamera Minerals (US) Inc. The company's Western Nevada Gold prop¬erty surrounds the Gooseberry Mine by several miles on all sides. Gold and silver mineralization at the Gooseberry Mine is restricted to a narrow calcite-quartz vein. Calcite makes up more than 80% of the vein throughout the mine. The host rock consists of porphyritic andesites and dacites constituting volcanic flows. The rocks are propylitized or silicified to a varying degree. This ore mineralogy, then, also describes the tailings processed by heap leaching. The Gooseberry tailings were auger sampled in 1983 and again in 1987 after a final lift of 109 kt (120,000 st) was deposited in 1983 and 1984. The total volume behind the dam was calculated from planimeter measurements from tailings surface to original area topography.

Jan 1, 1990