Search Documents

By K. N. Han

Coal is becoming increasingly important as a major energy source in the face of the world's depleting energy mainly based on oil reserves. Coal is by far the most abundant fossil fuel both in the United States and abroad. Currently, because of increased mine mechanization, the fineness of preparation plant feed is increasing. Further, in the future as the grade of coal diminishes and the sulfur content increases, upgrading preparation of coal is very important. Because the density of coal is less than that of rock materials that occur as impurities, coal is separated from such waste largely by gravity-controlled processes for particle size between 5 inches and 28 mesh. If the size of coal particles is below 28 mesh, froth flotation is a good method for upgrading fine coal. Previously, numerous investigators have tried to upgrade coal values by froth flotation(1-16) and have achieved moderate success. However, the recovery and grade of coals in the concentrates are not always satisfactory, especially when the particle size is small. In general, when the size of coal is below 100 mesh, the above methods suffer from poor grade and low recovery. The reason for this is that as size decreases, the effects of gravity diminish, and other forces take effect.

Jan 1, 1985

By W. K. Dressel

Over 2 million tons of steel furnace dusts are produced each year in the United States. Recycling of these dusts rather than disposal would conserve mineral resources, reduce land requirements for disposal, and decrease pollution. In addition to the iron content, the dusts contain appreciable amounts of zinc and lead. Removal of lead and zinc with simultaneous reduction of Iron oxide has been achieved by inert atmosphere roasting of carbon-containing pellets prepared from steel furnace wastes. High- and low-carbon wastes were blended to obtain mixtures with sufficient carbon to serve as a reductant during subsequent roasting. The mixtures were pelletized with the addition of bentonite and water, and the dried pellets were roasted in a stream of nitrogen at temperatures ranging from 900" to 1,150° C. Zinc and lead contents were reduced to the 0.1 percent level or less by roasting mixtures containing as little as 7 percent carbon for 1 hour at 1,100° C. ton metallization increases with available carbon content; 50 percent metallization is achieved with 7 percent carbon, 85 percent metallization with 12.5 percent carbon, and over 95 percent metallization when the pelletized mixtures contained in excess of 20 percent carbon.

Jan 1, 1973

By J. F. Oyler

One of the most important applications of material handling engineering technology occurs in iron ore pelletizing plants. Although the total installed value of material handling systems in such plants, as well as in many other modern process plants, is a relatively small percentage of the value of the plants (5 to 10% perhaps), their significance is considerable. Indeed this significance equals that of the more expensive process equipment in the plant, since the failure of any component of any system causes, shutdown of the entire plant. It is because of this increased consequence of failure that design criteria for process plants are more conservative than for conventional material handling applications. A second unique characteristic of material handling technology applied to process plants in general is the variety of materials being handled and the wide range of problems this variety presents. One extreme encountered is the stickiness of filter cake. Here the entire design effort is aimed at keeping the material flowing through transfer points and preventing it from building up on components. Another extreme is the conveying of fired pellets - hard spheres with a very flat angle of repose and abrasive characteristics severe enough to make conventional wear plate materials impractical.

Jan 1, 1976

By Biswajit Samanta, Pranjal Pathak

This article presents a customized genetic algorithms (GA) with new crossover and mutation operators to solve the short-term production scheduling problem of multi-mine mineral value chains (MVC). The preceding problem consists of determining the extraction sequence and destination allocation of blocks from all the mines collaboratively while closely meeting the quality and quantity requirements of the processing units subject to relevant technical and operational constraints. The short-term production scheduling is carried out at shorter scales wherein the operations are modeled in a great detail with large number of constraints. This makes the industry-scale instances of the problem computationally intractable for standard mixed-integer programming (MIP) solvers. Thus, a GA-based heuristic approach is developed to obtain nearoptimal solutions to the large-scale instances of the problem in a reasonable amount of computational time. Computational experiments show that the developed GA-based method is a promising way to handle industry-scale instances of the problem. Moreover, the sensitivity analysis on various parameter combinations of crossover and mutation operators indicates that the customized global mutation operator, when used in combination with the customized crossover operators, took on average 12.5% less time than the customized local mutation operator to converge to a solution.

May 21, 2022

By E. M. Haynsworth

The disposal of phosphatic clays has presented a problem to the phosphate industry since the mining of phosphate rock first began. As the flotation process was introduced in the late 1920's, the problem of clay disposal was increased significantly since clay is present in proportionally greater quantities in reserves yielding flotation concentrates. Because of their physical character and the tremendous surface area per unit volume, these clays have the characteristic of retaining large volumes of water as they are slurried during processing. The phosphatic clays with which we are dealing consist primarily of apatite, wavellite and montmorillonite. In the beneficiation process, we remove the -150 mesh material as waste. However, the particles are essentially smaller than -325 mesh, and more than 70% are smaller than three microns. The disposal of clay and the recovery of a portion of the water require settling areas with a capacity ranging up to 2 cubic feet for each cubic foot of phosphate matrix mined. According to a recent study by the Bureau of Mines, the average cost for disposal of these wastes is 24.5 cents per ton of, product (U. S. Bureau of Mines Circular 8404). This is a major cost of phosphate rock production.

Jan 1, 1970

By R. Pixler

Arch Mineral Corporation and Rocky Mountain Energy's Medicine Bow Mine in Wyoming presented an interesting challenge to the concept of mining a multiple-seam, dipping coal in the Hanna Basin. The 3362 and 2962 pits at MBCC were designed in a multiple seam coal consisting of 4 (and in some areas 5) bands of coal; these coal beds are all in the Ferris formation. The area was subject to some localized faulting and a major fault caused a physical restraint that we mined up against in our final cut. Using a 1570 dragline as the principal stripping machine, the concept of developing a bench for stripping the lower seams from the low-wall side of the pit was initiated. The results of this method of stripping were very satisfying for this pit through the completion of pit life and prompted us to use it in other areas at MBCC and at our other operations. Mining a dipping coal presents a small twist to conventional "flat" coal stripping. The spoil has a tendency to continually try to slide into the pit and the increased overburden on each cut as you mine down the dip creates spoil problems unless adequate design provisions are made prior to stripping.

Jan 1, 1986

By J. D. McAuliffe

The Homer-Wauseca Mine is operated by the Hanna Mining Company, three miles north of Iron River, Michigan on the Menominee Iron Range. The mine produces 5,300 tons of direct shipping iron ore daily. The present main producing level is at a depth of 1,500 feet below the collar. The ore body continues to a depth of 2,700 feet below the collar, to which depth the modern circular concrete shaft has been completed. A view of the property is shown in Figure #1. This paper is a report on the development of large underground boreholes used initially to conduct stope filling material into inaccessible, mined-out stopes. Later holes were drilled for ventilation raises, for mine drainage, for passageway for power cable, also for the primary breaking point for long hole stoping. Some, which were drilled as ventilation raises, were later stripped to a suitable size for a manway or ladder road. The holes varied in size from 6" to 30" with the present popular, economical working size being 16 1/4", used as a stope fill passage in mined out areas and for ventilation in deeper development. Foremost has been the desire to develop equipment suitable for drilling raises large enough for manways.

Jan 1, 1963

By William R. Bond

The pressure/vacuum lysimeter is being used as an effective vadose zone monitoring device for mining heap leach facilities, tailing disposal ponds and tailing waste sites. Their use has proven reliable for baseline data collection, early warning leakage detection and analyzing geochemical variations in the vadose zone. The lysimeter structure utilizes a closed cylindrical chamber made of PVC or inert material. The soil water intake portion of the cylinder is made of a porous material of low permeability. The application of vacuum or pressure to the unit is via two access tubes from the ground surface. Available soil moisture is drawn by vacuum through porous material into the lysimeter chamber and then collected from the access tubes. Case studies show their usefulness for monitoring around a uranium tailing pond constructed in glacial till material, under heap leach pads and pregnant, barren, and overflow ponds, and investigating the movement of contaminant moisture through old tailing deposits. Relatively easy to install and sample, regulatory agencies and facility operators are accepting and negotiating for their application as a site integrity monitoring device and unsaturated zone research tool. Their use at heap leach facilities lends credibility to solution balance calculations when considering a leachate loss of 5 or 10 percent can make or break a mine's profitability.

Jan 1, 1984

By R. D. Lord

This paper deals with the search for the best practical means of storing sulphide bearing tailings, where there is no residual excess of carbonate material. It is the common experience that the sulphide content decomposes, with the aid of bacterial action, and the resulting sulphuric acid escapes, along with any heavy metal solutes, through embankments that are usually porous to some degree. The problem is typified in the tailings of the uranium operations of Elliot Lake, Ontario, where mining started some 20 years ago. The approach to tailings disposal paralleled the practice for other hydrometallurgical plants treating gold and base metal ores. Impoundment areas were designed to retain solids, and a clear and neutral overflow was considered satisfactory practice. Now experience has shown that these areas, some idle for over a dozen years, release acids, in seepage and overflows, to an unacceptable degree. To protect natural water courses neutralizing plants are operated wherever required. Lime slurry is fed continuously into the tailings outflows in a quantity sufficient to raise the pH to 8.5 and precipitate heavy metals that may be in solution. The objection to this procedure is that the plants will require servicing indefinitely, unless a better remedy is found.

Jan 1, 1975

By Bryan Ulrich

Knight Piésold?s annual roundtable discussion was held at the Red Lion Hotel and Casino in Elko, NV on March 14. This year the title was, ?Roundtable discussion on material co-disposal/ co-placement in the mining industry.? This topic was chosen because of the benefits that the mining industry could realize through the advancement of improved methods of storing tailings and mine waste and from reducing short-and long-term environmental hazards while reducing the footprint of these facilities and making strides toward attaining a walk-away solution. Knight Piésold had a local representative, Bryan Ulrich, as well as representatives from its Denver, CO office, including Tom Kerr, president of Knight Piésold?s U.S. practice, and Jeff Coffin, Ph.D., geotechnical engineer, to help facilitate the discussion. The event played host to about two dozen attendees from several western states. Attendees included personnel from more than 10 mining properties, various corporate offices and academia. The purpose of the roundtable was to exchange ideas and information pertaining to broad topics revolving around the subject of co-disposal/co-placement in the mining industry. Compared with traditional conferences and symposia, the roundtable forum tends to provide a less inhibited format for discussion. In the roundtable format, lively discussions and applicable tangential departures are encouraged. This was the seventh in the series of the Elko Roundtable events. Previous roundtables pertained to: ? Heap leach pad design, construction and operation. ? Design, construction and operation of tailings storage facilities. ? Site-wide water considerations. ? Mine closure and cover design. ? Strides toward sustainability in mining. ? High-density tailings, paste and filtered tailings. Acid rock drainage for engineers and environmental scientists.

Nov 1, 2013

By Thornton L. Neathery

The low-grade talc deposits in Tallapoosa County, Alabama, are associated with a mafic-ultramafic rock complex that is part of a widely distributed schist and gneiss group. These rocks form a synform structure overlying Inner Piedmont lithology. Paragenetic sequence of the Tallapoosa talc is interpreted as enstatite-anthophyllitetalc. Talc occurs as massive boulders formed by the alteration of enstatite-anthophyllite and as finely disseminated discrete particles in the enclosing saprolite matrix. Weathered rock reaches depths as great as 60 feet. The quality and quantity of the talc, however, are variable. Mineral analyses of the talc-bearing samples, by petrographic grain count, indicate a talc content of 16 to 26 percent. Most of the talc occurs as plates or scales that are moderately stained with limonite. Fibrous talc also occurs in the deposits and is often mistaken for anthophyllite asbestos which is intimately associated with the talc. The size, shape, and occurrence of the talc deposits precludes any method of min¬ing other than open-cut. A small-scale mining operation began in the district in 1969. Potential capacity of the operation is 5, 000 tons per year. Inferred reserves, based on field investigations, are placed at approximately 8 million tons. Approved for publication by the State Geologist, Geological Survey of Alabama.

Jan 1, 1970

By R. K. Singhal

In 1990, Canada produced 69.4 million tonnes of coal of which some 65 million tonnes was produced by surface mining methods. The two Western Canadian provinces, Alberta and British Columbia produce approximately 55 million tonnes of coal by surface mining. These two provinces also provide the bulk of the metallurgical coal for export. The geological conditions in the Western provinces particularly in the mountain region are complex. The coals are friable and the seams are steeply inclined, sheared, intensely folded and faulted. There may be as many as 15 to 20 coal seams present with true thickness ranging from 2.5m to over 8m. Most of the Canadian surface mines are large (over one million tonnes per annum) using modern mining equipment such as shovels, high capacity trucks and draglines. At present the industry is going through another of its up and down cycles but has continued to make impressive gains in productivity. This has been achieved through greater mechanization, better management practices and a will to succeed in a highly competitive world market. This paper presents an insight into the current status of the Canadian Coal Industry and essentially updates the information given by the authors at previous SME meetings.

Jan 1, 1992

By Hubert E. Sherer

The mining industry is presently one of the most heavily capitalized industries in the U.S. (U.S. - Statistical Abstracts, 1979). U.S. sales of new mining equipment (not including environmental, preparation, or long distance transportation equipment) are projected to reach approximately $5 billion/year in 1980 (Frost and Sullivan, 1979). Of these new equipment sales approximately 30 to 40 percent of this equipment will be used to replace old equipment. Therefore, an increase of efficiency in the use of equipment replacement capital could have substantially positive effects for the U.S. mining industry. This is very critical in these times of restricted capital availability, double digit inflation, burdensome governmental regulation, and rising foreign competition in the mining industry. This paper examines the numerous factors that constitute the typical mine equipment replacement problem. A computerized, mathematical model is formulated to utilize historic cost and production information to predict equipment cost versus age for the existing and potential replacement machines. Another part of this computerized model determines the best equipment replacement strategy that accomplishes estimated production goals at a minimum discounted cost. This computerized model is an easily used, consistent method of determining the optimum replacement age for any equipment unit or fleet of equipment at a mining operation.

Jan 1, 1982

By R. B. Steele

The paper contains the results of the physical and mathematical simulations (based on the finite elements simulation) of the length and shape influence on the mechanical strength of the brex. Key words: Stiff extrusion, extruded briquettes, BREX, mechanical strength, cold strength, compressive strength, tensile splitting strength, oval shape, finite elements simulation. INTRODUCTION Extruded briquettes (BREX) exhibit a set of unique properties when compared with briquettes formed by alternative methods. Brex generally have sufficient integrity right after extrusion to withstand the necessary handling and stockpiling and does not require any special means and tools for the green briquettes strength conservation. In a typical die without an ancillary cutting device green brex tend to have very high length to diameter (L/D) or length to section area ratios. For round hole dies the brex are typically 5to 6 times the diameters and even longer. Stiff-extrusion allows also for the very easy changing of the forming dies. Dies with different cross-sectional shapes of the brex (round, ovals, square, hollow structures and many other two dimensional shapes) are possible, and common. The results of our investigations show how these geometrical shape factors contribute to overall quality of the brex both in terms of strength and as new charge components in metallurgical furnaces and processes [2-4]

Feb 27, 2013

By J. A. Organiscak

Longwall mining technological improvements have provided significant increases in productivity over the last 15 years. Longwall productivity is anticipated to continue to escalate with expanded application of automated equipment. Automation technology that will likely be adopted over the next 5 years is memory cut with shearer initiation of shield movement supervised by a couple of face workers. Operations using this technology will most likely relocate many production workers from the face to the outby gate entries and position several face workers outby the shearer, exposing workers to different health and safety risks. These changing risks are primarily related to worker relocation and expected increased production levels. Workers outby the face will most likely have less dust and noise exposure, but will be exposed to other safety hazards associated with outby equipment movement, materials handling, and gate entry ground movements. The face workers will most likely be exposed to higher respirable dust and noise levels generated by the equipment at elevated production rates. Methane gas emission is also expected to increase with faster mining rates. These operational changes and the control technologies needed to reduce redefined longwall worker hazards at semiautonomous longwall operations require examination to maintain the health and safety of mine workers.

Jan 1, 1996

By J. A. Marts, R. C. Gilmore, S. Saki, J. F. Brune

El modelamiento de la dinámica de fluidos computacional (CFD por sus siglas en inglés) implica la creación de un dominio de cálculo llamado malla o rejilla para resolver las ecuaciones que definen la física del flujo de fluidos. Este proceso comprende a menudo emplear la mayor parte del tiempo en esfuerzos de modelamiento. En un proyecto patrocinado por el Instituto Nacional de Seguridad y Salud Ocupacional (NIOSH), los investigadores de la Escuela de Minas de Colorado utilizaron un enfoque innovador de mallas, el cual permite una fácil adaptación del modelo CFD para adaptarse a una variedad de geometrías de minado de tajos largos ventilados por canales (bleeders) y progresivamente sellados (referidos a menudo como bleederless en los Estados Unidos), con la porosidad y la permeabilidad de la cámara escalables en un amplio intervalo. En este trabajo se presenta la metodología del enfoque de enmallado y escalado junto con las recomendaciones para el uso de modelos CFD en aplicaciones de ventilación para las cámaras en tajos largos. La nueva técnica de enmallado se utilizó para evaluar la función de un retorno hacia atrás en una cámara progresivamente sellada y otra cámara ventilada por canales.

Jan 1, 2014

By M. Mathiba

High CO2 fluxes associated with reclaimed coal mine spoils pose an environmental hazard where such sites are used for building. CO2 concentrations in excess of 25% have been reported in homes constructed on or down gradient of such spoils. The objective of this study was to investigate the effect of a mitigation trench used at one mine site on CO2 fluxes across the trench using chamber?based trace gas measurement. LI8100 automated CO2 flux system was used to measure CO2 fluxes from 32 sample points located across a deep mitigation trench on June 8 and 9. The maximum recorded fluxes were 7.29 and 8.18 µmol/m2/s, with averages of 4.15 and 5.50 µmol/m2/s, up and down-dip respectively. These preliminary results show CO2 flux is higher up-hill than down-hill at 95% significant level. This work shows that flux measurement can be used to investigate CO2 migration on reclaimed mine land. Further work is necessary to allow geostatistical modeling of the spatial variability of CO2 fluxes over reclaimed coal mine spoils. Knowledge gained would assist mining practitioners and regulators in reclamation planning for envisaged post-mining land uses.

Jan 1, 2010

By S. M. Hossaini, M. Ataei, H. Moosavi

The abstract highlights the importance of pillar stability in underground coal mines and the influence of rock mass strength and joint orientation on pillar behavior. The study employs numerical modeling using the distinct element code (UDEC) to investigate the impact of these factors on pillar stability. The research considers different joint orientations and varying rock mass strengths, analyzing parameters like stress distribution, displacement, and failure patterns. The findings reveal that both joint orientation and rock mass strength significantly affect pillar stability, with specific combinations leading to reduced safety factors and increased deformation. The study concludes by emphasizing the importance of considering these factors in pillar design for safe and efficient mining operations.

Apr 4, 2022

By David G. Van Hersett

The single most unique design feature of the Centralia Coal Mine is the public information program. Just what the heck does public information have to do with the development of a coal mine? The utilities of today have had to build larger and larger plants to keep down the costs of power to the consumer. The large plants require huge amounts of capital, take up large areas of real estate, consume unprecedented amounts of coal, and generate large quantities of waste products which have to be reckoned with. Coal mines supplying these plants have also increased in size and production to meet the power plants' unending appetite for coal. This means the disturbance of great areas of land and significant alterations to the landscape. Today's public is greatly concerned about the environment in which he is living. The great size of a power plant with its large stacks, coal piles, and the coal mine with its large earth movers, disturbed acreages and the resulting waste products of both operations appears to present a threat to his environment. Because of this,' many power plants and coal mines are having public acceptance problems. This has resulted in the passage of stringent legislation and in some cases brought upon construction delays for major power plants.

Jan 1, 1970

By Thomas R. Yanske, Jonathan E. Carmack, Lyndon M. Clark

In order to maximize the extraction of high grade pillars at The Doe Run Company, artificial pillars are created using cemented rock fill (CRF). CRF pillars aid extraction of pillars in two ways. One is to offer back support for the immediate area where pillars are being extracted. The second is to increase the post failure residual strength of pillars surrounded by backfill. The CRF is produced using a combination of minus 1.0 m run of mine (ROM) rock and minus 5 cm crushed rock. Depending on the operation the CRF slurry is either produced in an underground or a surface batch plant. The slurry and rock are transported to the fill area by truck where they are mixed and placed in 1 m lifts. To reduce the amount of CRF needed, fill fences are constructed around the perimeter of the CRF pillar. Within these fences ROM CRF is placed in lifts until within 0.6 m of the back after which minus five centimeter CRF is slung tight to the back utilizing slinger trucks. In constructing these artificial pillars a number of set procedures have been established to ensure that the work is done both properly and safely.

Jan 1, 2001