Search Documents

By R. L. Loofbourow

In addition, dewatering is seldom complete because of aquifer irregularities and an operator's natural reluctance to start a costly study program, provision of wells, and pumping long before mining begins. In some cases, water pumped from the mine is used in treatment. This use is suggested as a way to minimize effluent effects. The true objective of water supply, however, is to provide water of satisfactory quality at the rate needed and at the least cost. Pumping to permit efficient mining isn't likely to coincide strictly with that objective during much of the mine life. The history of mining is replete with efforts, some highly ingenious, to control mine water. Methods that might be used to tackle the challenge Operators of wet mines are faced with both obvious pumping costs and some unquantified water costs. It is possible to reduce both types of costs, generally by reducing inflow to the mine area-and a surprising number of methods have been used to do this. Both the obvious and unquantified costs at a wet mine are now multiplied by: •Increasing costs of power, labor, equipment, and supplies; •Work at greater depth and, in some cases, in wetter ground; •Increasing use of hydraulic fill; and •Increasing zeal in protection of surface and groundwater quality. There are many easily overlooked ways in which mine water may add to hazards and costs (Loofbourow, 1973). As to their importance, consider these examples: •Increased maintenance of equipment, tires, roads, and ditches; •Increased difficulty in supplying proper ventilation; •Increased hazards from ice and use of electric power; • Loss of friable ore minerals and fines stuck on conveyances and in chutes; •Need to use more expensive methods and explosives; and •Decrease productivity of equipment and personnel. Expressed as cost per unit of ore produced, these unquantified costs can be high. Ideally, advanced dewatering should eliminate most of them. Advanced dewatering is a highly effective water control method, but it isn't problem free. Mines in ideal ground for advanced dewatering are most unusual. To be effective, water must be pumped at a comparatively high rate for a period longer than the life of the mine, from below mining depth. Effects on both groundwater and surface water are likely to be drastic. of increasing mine water costs are listed in the accompanying table. Ten groups of possible methods are cited. Most have been demonstrated in mining; two are known from industries other than mining.

Jan 12, 1980

By Bahadir Ergener, Angel Maria Tobar Escudero, Sandra Nowosad

Modern mining companies are increasingly turning to integrate digital technologies and circular economy (CE) principles to increase the sustainability of their operations. The so-called “mine of the future” is envisioned as a smart, integrated system where technologies such as automation, artificial intelligence, digital twins, and real-time data analytics work in harmony with human decision-making and environmental responsibility. Already in 2018, McKinsey and Co. identified that the three drivers that would define a technology-enabled change in mining would be technology, including digital, analytics and automation, management systems able to identify the potential and value of the new technologies, and the culture and capabilities of the organisation, leaning to more agile and responsive organisations. From the three drivers, in the last five years most developments have been centred in the first one. Yet despite rapid advances, the adoption of new technologies across the industry today remains uneven and often slower than expected. Furthermore, it has been identified that the problem on the technology uptake often relay on the lack of operational readiness, process incompatibility or misalignment, and resistance to change within the mining operation. At the same time, leading companies like Rio Tinto, BHP, and Anglo American have each launched major digital transformation programs. Rio Tinto, for instance, operates one of the world’s largest autonomous mining fleets and has integrated digital technologies across nearly all its operations (Rio Tinto, 2025). BHP is actively investing in information and communication technology (ICT) development as artificial intelligence, big data analytics and robotics, and has partnered with battery companies to pursue circular economy initiatives. Only in 2024, their ICT spending reached US$ 438.3 million (Global Data, 2024). Anglo American has rolled out its FutureSmart Mining™ framework, explicitly aligning innovation with circularity and sustainability goals (Anglo American, 2025). The accelerating pace of change across leading mining companies along with the uneven adoption in the technology uptake clearly state how digital transformation is no longer just about implementing new tools, instead it requires a fundamental shift in how people, processes, and culture are aligned. Addressing only the technical layer, while neglecting the human and organizational dimensions, leaves transformation efforts fragile and unsustainable. As the industry must act decisively to close this gap, the true test of transformation is today centred in changing behaviours, mindsets, and systems. Even at the listed leading companies, initiatives have encountered cultural and structural resistance that are relatable to the industry in large: siloed departments fail to collaborate, procurement teams focus on upfront costs rather than lifecycle value, and operators are often excluded from early-stage planning, reducing buy-in. In many cases, a lack of communication or failure to link technology to real operational bottlenecks leads to disengagement at the ground level. This friction reveals a broader issue: mining organizations have historically treated technology and culture as separate domains, when in fact they are deeply interdependent. To address this, the authors propose a systems engineering approach focusing on the mining operations as a complex socio-technical system composed of people, processes, and technologies. Systems engineering offers tools and frameworks for mapping interactions, aligning incentives, designing for feedback and adaptation, and integrating change across organizational boundaries. Specifically, besides technical requirements, it demands treating culture not as an afterthought or side-effect, but as a design variable that must be intentionally shaped alongside infrastructure and workflows. This paper explores how this approach can be applied in practice, by analysing a real-world case scenario where resistance to innovation was overcome not by technical capabilities alone, but through alignment of stakeholder incentives, thoughtful communication, and cultural integration. A particular focus is set on the adoption journey of the Powerbit X, a drill bit technology with significant potential for operational and environmental gains.

Feb 22, 2026

By Chee Theng

"It is not surprising that the most popular key takeaway from the Developing Diversity in Mining workshop (see box) held on the first day of the SME Arizona Conference in December was, “Have more parties!”The adage that mining professionals work hard and play hard was clearly demonstrated at the two-day conference in the JW Marriott Tucson Starr Pass Resort & Spa in Tucson, AZ. Nearly 550 participants, some of whom had left behind frigid temperatures and thick parkas in their hometowns, attended a full slate of technical sessions, shared industry experiences and knowledge, reconnected with buddies in the industry, and made strategic new contacts in the conference’s collegial environment, aided by the mild Arizona winter.To start off the technical sessions, John Mansanti, president and chief executive officer of Crystal Peak Minerals and 2017 SME president, entertained a packed lecture room with his keynote lecture on “Tariffs, Embargos, and Cartels ... Oh My! A Perspective on Potash.” Mansanti gave the audience the benefit of his more than 35 years of experience at companies including Barrick Gold, Newmont Mining Corp., Placer Dome, Freeport-McMoRan and Intrepid Potash, where he was senior vice president for operations, technology and strategy. At the luncheon, Justin Cross, general manager of Freeport-Mc- MoRan’s Bagdad operations, spoke on how the role of a leader in mining is transforming from one based on technical expertise to one based on the ability to collaborate, to lead and to adapt to changes in technologies and skill sets, in his talk on “Knowing When to Learn, When to Lead and When to Manage.”"

Feb 1, 2019

By M. Werner

Mining in the Coeur d'Alene Mining District has been going on for over 100 years with a long- term continuation very likely. Mining is presently carried out at depths below the -5000' horizon. As mining continues at ever increasing depths, higher in-situ rock stresses and subsequent rock deformation is encountered making mining costly and hazardous. To provide access for men and materials in such areas, a wooden raise preparation structure is typically built. Although these structures provide adequate support and access, they have proved to be very costly to construct and maintain.

Jan 1, 1986

By H. W. Gussmann, R. G. Rohrs, E. van der Merwe

Salinity in Effluents carries a high penalty as a result of toxic­ity, corrosion, limited re-use potential, scaling and environmental impact. Although the high TDS, such as Calcium sulfate, other than metals are still being dealt with a low key non issue basis, they are receiving more and more attention from regulators. Traditional solutions to solve these problems are costly and inefficient and create therefore severe constraints on the prof­itability of mining operations and out-price in general the finan­cial resources for environmental clean up operations. Going up the technology versus cost curve the most econom­ic solution to pollution is dilution but which is difficult in a coun­t1y shoti of water. If this can't be done, the second best, at least in sunny areas, is, to pump the whole effluent on a tailings dam for evaporation. Depending on the contaminants, one may have to pond the efflu­ent to avoid re-dissolution and seepage into the ground. The next most common solution to pollution is the addition of lime to remove and concentrate any dissolved metals and then dump the product, hidden in a mass of gypsum in a convenient place. Again ponding may be required to avoid ground pollution. However the treatment costs start to rise steeply if it is not allowed to discharge the limed overflow solution because of its high calcium sulphate content. Further treatment is then required in the form of high cost and high tech membrane process tech­nology such as reverse osmosis or dialysis or even mechanical driven evaporation.

Jan 1, 1998

By CHONG WEI, TATYANA KATSAGA, DEREK APEL

This study provides an effective determination process of the interface microstructural parameters in the numerical modeling of the mechanical interaction between two different geomaterials involved with frictional-bonded interfaces, such as the interaction between backfill columns and the surrounding rocks, or the soil-structure interaction, by using the coupled finite-difference and discrete-element (FD-DE) method. The test results validated the feasibility and rationality of the coupled FD-DE method for modeling the combined specimens with frictional-bonded interfaces or joints. Furthermore, this study provides valuable numerical modeling experience for investigating the shear behavior at the interface between cemented backfill columns and surrounding walls by using the coupled FD-DE method.

By M. L. Free

Acid consumption in copper heap leaching is determined by the minerals present in the ore. Gangue minerals such as biotite and chlorite consume acid together with copper-bearing minerals such as chrysocolla and malachite. Acid consumption is affected by the rate of acid application and the particle size. Some gangue minerals undergo alterations and cause precipitate formation during acid leaching. Other minerals form due to precipitation as dissolved ion concentrations from a variety of mineral sources combine to exceed saturation levels. Copper recovery is related to all of these events. This study presents information on acid consumption of various gangue minerals as well as data for copper recovery from an associated copper ore.

Jan 1, 2010

By J. Alatalo

Autogenous grinding is a process of reducing the particle size distribution of an extracted ore by using the ore itself as the grinding media. It is a process that is difficult to control and there is a lack of knowledge of the events occurring inside the mill. To find out more about how the mill behaves under different processing conditions, a full factorial test was performed with iron ore in a pilot-scale pebble mill at the LKAB R&D facility in Malmberget. To complement this work, a strain gauge detector was embedded in one of the mill?s rubber lifters, the Metso Minerals continuous charge measurement (CCM) system, and was used to get more information about the charge dynamics. The data from the experiments has been analyzed. For production purposes, an increase in the number of particles smaller than 45 µm can be regarded as a probable increase in the production rate. The analysis shows that there will be an increase in fines at 65% of critical speed, especially when the mill is 45% full. This setting will also increase the power consumption, but improves the grindability of the ore even more. The deflection of the lifters is smaller for lower critical speeds. A higher degree of filling also gives a smaller toe angle and a higher shoulder angle as expected.

Nov 1, 2011

By J. Alatalo

Autogenous grinding is a process of reducing the particle size distribution of an extracted ore by using the ore itself as the grinding media. It is a process that is difficult to control and there is a lack of knowledge of the events occurring inside the mill. To find out more about how the mill behaves under different processing conditions, a full factorial test was performed with iron ore in a pilot-scale pebble mill at the LKAB R&D facility in Malmberget. To complement this work, a strain gauge detector was embedded in one of the mill?s rubber lifters, the Metso Minerals continuous charge measurement (CCM) system, and was used to get more information about the charge dynamics. The data from the experiments has been analyzed. For production purposes, an increase in the number of particles smaller than 45 µm can be regarded as a probable increase in the production rate. The analysis shows that there will be an increase in fines at 65% of critical speed, especially when the mill is 45% full. This setting will also increase the power consumption, but improves the grindability of the ore even more. The deflection of the lifters is smaller for lower critical speeds. A higher degree of filling also gives a smaller toe angle and a higher shoulder angle as expected.

Jan 1, 2011

By Su Yang, Pang Shun, Xiaoding Xu, Guodong Yang, Hengfeng Liu, Meng Wu, Yuejin Zhou

By introducing the hydrochemical damage variable of coal gangue granular material, this paper analyzed the evolution law of gangue mechanical parameters with hydrochemical damage. By constructing a gangue damage model considering multifield coupling, the damage mechanism of gangue under multi-field coupling was revealed from the microscopical aspect, and the influence law of gangue damage mechanism on the dissolution of toxic substances under multi-field coupling was obtained: the conditions of Test 1 have the greatest influence on the porosity of coal gangue, and the damage of coal gangue is the greatest. Cu, Zn, Cd, and Pb are more easily leached under acidic conditions. The coupling effect of seepage, temperature, and chemical field can promote the formation of secondary voids, change the voids, and form migration paths in coal gangue. The kinetic model of toxic leaching of coal gangue under multi-field coupling can be well characterized by Elovich equation. The release mechanism of heavy metals is mainly manifested as delayed diffusion or dissolution in the early stage, diffusion and dissolution in the middle stage, and depletion in the late stage.

Nov 23, 2023

By Marcel Haffen, Jean Janin

The purpose of grouting is to modify the permeability and strength characteristics of the subsoil in such a way that the planned structure can be efficiently constructed at a given location. This technique, which originally underwent considerable development in the field of dams construction is constantly evolving and it becomes more and more important in urban zones of intensive underground development for projects such as transport tunnels, stations, car parks, ect. Grouting becomes more and more indispensable whatever the natural characteristics of that subsoil ; such is the case particularly when the planned work runs through cohesionless granular soils, usually water-bearing such as alluvium, sands, disturbed ground, fill material, etc. The selection of the grouting method and the extent of treatment required at depends on two fundamental factors. 1º) nature and behaviour of subsoil to be treated. There is no need to stress the necessary of a good knowledge of geotechnical, hydrological and chemical characteristics of the ground to be treated. At the present time the specialists in these fields have available numerous methods of analysis, either laboratory or field tests, which enable to evolve a suitable treatment.

Jan 1, 1997

By George L. Atwood

The Monsanto Company's Henry Mine is located 17 miles northeast of Soda Springs, in the southeast corner of Idaho. Ore being mined is phosphate rock which lies in the Permian Phosphoria formation. The ore is the raw material for Monsanto's three furnace elemental "P" plant near Soda Springs. The finished product from the furnaces is elemental phosphorus which is subsequently used in the manufacture of detergents, food preservatives, fire retardants and other consumer items. Mining is by open pit methods using 0-9 crawler tractors to rip and push-load rubber tired scrapers in stripping and mining operations. The equipment spread consists of six D-9G crawler tractors, four Caterpillar 6578 scrapers, eight Euclid S-24 scrapers, one Reich T750 drill and one Caterpillar No. 16 patrol plus various support equipment. Stripping is performed on a 12-month basis, two shifts per day. Mining is performed mainly in the summer months on a one shift basis. The hauling season begins May 15 and ends November 1 due to freezing weather and snow conditions. Annual production is 1,000,000 tons of phosphate rock and 2,500,000 to 3,000,000 yards of stripping. Stripping, mining and hauling is performed for Monsanto by Dravo-Soda Springs, a mining contractor. Dravo-Soda Springs owns, operates and maintains all equipment used in stripping, mining and hauling. The contractor is paid for stripping by the bank yard and for ore mined and hauled on a tonnage basis. The Monsanto elemental phosphorus plant began production in 1952 with ore being trucked to the plant from the Ballard Mine. Haulage was over public roads in 15, 24-ton semitrucks. A private haul road was constructed from the Ballard Mine to the Monsanto Plant in 1958 and 1959 to accommodate trucks with two twenty-yard trailers. This 11/ mile road was first used in the 1959 hauling season. In 1965, five new Kenworth tractors with two, 'forty yard trailers were introduced into the haulage system. These units carried 120 ton payloads and were used until

Jan 1, 1972

By Ava Walker

The first form of a surety bond was an honest handshake between two or more parties agreeing to a decision, and their personal guarantee of following through to completion. This has all changed. In 1895, the United States Treasury Department disclosed that $35 million worth of personal surety guarantees on file had become worthless. A law was then passed requiring all surety bonds, in favor of the United States, must be corporate surety bonds. Today, a surety bond is one of the nation's leading fi¬nancial instruments used to guarantee the completion of an obligation. One hundred-fifty years before cor¬porate surety bonds, outcrops near Richmond, VA, were being mined. These surface mines became under¬ground mines. Today, both are still being used to obtain a leading energy source, coal. Since that time, more than 5956 km2 (1.47 million acres) of coal mined lands have been reclaimed in the US (Coal News, August, 1987). More than 25,000 state and Federal mining permits cover¬ing 14,164 km2 (3.5 million acres) have been issued during the last 10 years. Coal production has exceeded 7.2 Gt (8 billion st). More than 5665 km2 (1.4 million acres) of mined land has been reclaimed by active coal mining opera¬tions and 267 km2 (66,000 acres) of abandoned mined lands have been re¬claimed by others. Reclamation bonds were freely writ¬ten in the 1970s. So why are they almost extinct today? Contract bond losses have been severe in the past several years, sureties reporting losses exceed¬ing 110%. But the same proof is not provided on coal reclamation bonds. A surety bond is generally required when one party has an agreement with another party, and that party wants a guarantee from a third party that a job will be completed according to the terms and conditions of a written contract. In the case of a reclamation bond, the surety company (surety) is the financial party. It extends the credit and a guarantee to the obligee (the State, Commonwealth, or Office of Surface Mining) that the principal (the coal operator/company) will complete the terms and conditions of the contract (the rules and regulations governing mining and reclamation). The Surety Association of America defines a surety bond as an agreement providing for monetary compensation should there be a failure to perform specified acts within a stated period. Webster's Dictionary defines surety in the following ways: "l: the state of being sure; 2a: a pledge or other formal engagement given for the fulfillment of an undertaking and; 3b: one who has become legally liable for the debt, de¬fault, or failure in duty of another." Banks never make accommodation loans. Either the loan is good or no loan is made. Surety companies feel the same way about surety bonds. In fact, the average person does not realize the dangers of becoming surety for another. How does a surety determine if a company is worthy of receiving surety credit? How is a coal account under¬written today for an obligation that may not be released for many years? When a surety company executes a reclama¬tion bond, it financially puts its name behind the coal company and its guaran¬tee that should the coal miner default on the obligation, the surety will fulfill the contract. How is the surety to determine if a coal company may still be in business five, 10, 20, or 40 years from today?

Jan 1, 1989

By Howard A. Jongedyk, Jerry Wachtel

Advancements in tunneling technology and underground construction, plus rapidly rising costs of land, and a higher priority being placed on urban esthetics, make tunnels a more attractive option for certain portions of the highway construction program. Recent emphasis placed on fuel conservation reinforces the need for tunnels as a means of shortcutting circuitous routings designed to avoid potentially undesirable environmental impacts on any given area. Larger and more complex tunnels which have been constructed in recent years attest to this greater interest. More than 100 major highway tunnels are in operation in the United States. Highway tunnels commonly have much higher initial cost compared to surface routes. Where extensive cut and cover is involved, temporary disruption of the surface area may prove costly. In exchange for these costs, certain environmental advantages result. The purpose of this paper is to discuss some of the environmental advantages of highway tunnels and some of the unsolved problems related to obtaining maximum use of highway tunnels and research underway to help solve these problems.

Jan 1, 1974

By Hidehiko Nakazaki, Sakuro Murayama, Mitsuo Miura, Masaaki Endo, Yoshiaki Hurukawa

This is a detailed report of construction experience of a tunnel built by a shield of rectangular cross section with reinforced concrete segments. In case of tunneling by a rectangular shield, there were the following problems to be overcom by technical developments; (1) structural joints between segments, (2) complexity in erector handling, (3) exact steering operation of shield and perfect filling of tail void left around the lining erected. Such rectangular shape of cross section has various advantages comparing the conventional circular shape as follows; (1) effective utilization of excavated space, (2) greater overburden depth, (3) stability of lining against unbalanced earth pressure caused by neighbouring construction.

Jan 1, 1979

Crushing and grinding The Crushing and Grinding Technical Committee There was substantial activity in the area of crushing and grinding with the improved outlook in the industry. The Crushing and Grinding Committee's theme of 1987's Annual Meeting in Denver was Fundamentals of Mechanical Design for Crushing and Grinding Mills. At the meeting, the concept of gearless sag mill variable speed drives was taken out of the closet, dusted off, and a wraparound motor was put on hard copy with the ordering of a 9.7- x 4.5-m, 8.2-MW (32- x 15-ft, 11,000-) sag mill. Additionally, comparisons were provided to the mill design of the gearless drive sag mill and the twin 4.5 MW (6000 hp) do variable speed drives placed on the drawing board for the Kennecott UCD Expansions. This involved a 10- x 4.5m, 8.9 MW (34- x 15 ft, 12,000 hp) sag mill. Differing opinions were also expressed in technical presentations pertaining to the need for quality mill specifications in design and manufacturing. J. Berney-Ficklin of Bechtel presented a paper outlining the need for quality design and manufacturing specifications in large scale grinding mills, and the overall cost reduction in capital and operating costs. Others presented differing specific views, but all emphasized a central theme. Quality and reliable designs in large mills should not be compromised. In-pit crushing applications continue to increase, overseas and in the US, in both mining and quarrying. Different in-pit crushing units have been classified as mobile, with integral transport systems; semi-mobile, typically modular systems that use separate transporters for repositioning; semi-stationary plants that must be dismantled before transporting and typically require earthwork and concrete foundation work; and stationary in-pit crushing plants, which remain in place for the life of the pit. The majority of equipment sales of conventional crushing and grinding circuits in 1987 were to gold mining operations. There have been two areas of end use: • conventional jaw/gyratory or impact crushing circuits preparing low grade ores for heap leaching; and • small scale sag/ball mill circuits preparing higher grade ores for classical cyanide leach/ recovery circuits. There was also continued interest in ABC and SABC circuits for both base and precious metals plants. High pressure roll crushers continue to attract considerable interest in the cement industry. There, they are used to prepare raw materials or clinker for subsequent ball/tube milling. However, they have apparently been less successful in the mineral industry where the energy savings/ capacity gains have been much less dramatic. Several papers covering the theory and application of these machines were presented in an industrial minerals session on cement at the SME Annual Meeting. The Third International Conference on Hydrocylones, held in England in October produced several papers of interest on classification and screening to the mining industry. In particular, a new cyclone apex, developed by Mt. Newman Mining, shows promise of reducing water flow to the cyclone underflow stream and, therefore, increased underflow pulp densities and reduced fines recycle in grinding circuits. A twin vortex hydrocyclone was also described and shown to give a sharper split than conventional units. Similar double cyclones were introduced in the 1950's, but failed to achieve widespread acceptance. This was due mainly to a proneness to blockage in the transitional zone. It will be interesting to see whether this latest variant can overcome this problem in the typical operation. A number of North American iron ore plants installed the capability to produce fluxed iron ore pellets. Most chose to grind the stone on site with circuits designed to grind taconite ore. Methods employed to grind this material included single-stage ball mills closed with fine screens, rod and ball mill circuits - both open and closed with cyclones - and semiautogenous mills, followed by ball mills closed with screens or cyclones. Dewatering and tailings disposal B.M. Moudgil and D.L. Sober, University of Florida Due to tightened environmental regulations and the need for more efficient land use, a greater interest in dewatering and waste disposal has developed. As a result, research efforts in flocculation, surface chemistry, and polymers science have focused on the problems related to the dewatering of solid mineral wastes. A few studies have been conducted to examine the flocculation process. Hogg et al., (1987) discussed the formation and growth of flocs. They determined the size and density of flocs was controlled by the physical conditions of the system (e.g. agitation,

Jan 5, 1988

By J. Rostami, J. Brune, S. Slouka

Respirable dust poses long-term health issues to personnel working in mining and civil projects where mechanized mining and tunneling machines are used for hard rock excavation. Machines, such as longwall shearers, roadheaders, or continuous miners, use consumable picks to cut rock. However, rock dust is generated in the work environment each time the pick tip contacts the rock surface. Additionally, the generated dust can be reintroduced into the air further down in production, such as at transfer points. The purpose of this study is to characterize respirable dust particles generated at the pick tip at two stages of pick wear: new and moderately worn. Understanding dust characteristics in terms of concentration, size distribution, and particle shape throughout the life-cycle of the pick will provide a basis to mine and tunnel operators for changing out picks to mitigate dust generation at the source. This paper discusses the dust characteristics generated from preliminary full-scale cutting tests in a laboratory of an igneous rock block cut with conical picks at new and moderately worn levels of wear. The moderately worn pick generated a size distribution that favored smaller particle sizes compared to the new pick. The moderately worn pick also generated more overall dust, as the concentration level in mg/m3 was over double the amount of the new pick. Lastly, both picks generated particles that had similar aspect ratios and roundness measures.

May 18, 2022

By J. Köppel, K. Kovári, Ch. Amstad

INTRODUCTION The measurement of displacements in soil or rock in the vicinity of underground openings provide valuable information for a better understanding of the behaviour of the structure. On the basis of systematic observations conclusions can be drawn concerning - safety of the opening in the various stages of excavation - effectiveness of the support measures - nature of the rock pressure to be expected - influence of the construction of the opening on neighbouring structures (settlements of foundations, underpassing other tunnels etc.) - comparison of theoretical predictions with the actual structural behaviour (1). Today there are several types of suitable instruments available that can be employed at reasonable costs for such investigations (2). The most important ones are the multiple point borehole extensometer, the inclinometer and the multiple point borehole deflectometer. As is well-known, the extensometer only measures the displacement component in the borehole axis, while the inclinometer and the deflectometer provide monitoring of rock mass movements normal to the borehole axis. In the following a new instrument is described, which has been given the name Extenso-Deflectometer ISETH. In this single piece of equipment certain features of the above-mentioned three types of borehole instruments are incorporated. it enables the measurement of all three components of the displacement vector at consecutive points along the borehole, the axis of which may have any direction in space. This device is portable like the inclinometer. A simplified version

Jan 1, 1979

By John Frostiak

The Campbell gold operation of Placer Dome Inc. produces an arsenopyrite-sulfide concentrate that must be treated by roasting, biooxidation or pressure oxidation to obtain high gold recoveries. Pressure oxidation is a proven process that also meets Ontario's stringent environmental regulations. A comparison of biooxidation and pressure oxidation was completed early in 1990. Placer Dome selected pressure oxidation as the preferred process to replace the roaster. The commercial plant design was based on technology supplied by Sherritt Gordon. In July of 1991, the existing roaster operation was shut down and a new pressure oxidation plant was commissioned. The Campbell Red Lake Mine, in Balmertown in northwestern Ontario, is the first plant in Canada to use Sherritt Gordon's pressure oxidation technology to recover gold from a refractory ore body. A similar process has been used at Sao Bento in Brazil since 1986. The Porgera complex in Papua New Guinea also uses Sherritt's technology. At the Campbell Mine, gold occurs as either free gold or is encapsulated with sulfide minerals, mainly arsenopyrite, pyrite and pyrrhotite. These sulfide species are recovered from the ore by crushing and grinding to 80% -75. µm (200 mesh), followed by flotation. About 40% of the gold in the ore is recovered by gravity separation. The remainder reports to the ground slurry feed to flotation. The flotation concentrate averages about 55 to 60 t/d (60 to 66 stpd). A typical analysis is shown in Table 1. Before the installation of the pressure oxidation plant, the flotation concentrate was treated in a two-stage, fluid bed roasting circuit. Roaster off-gases passed through two parallel sets of cyclones, followed by electrostatic precipitators. Arsenic trioxide was captured in a four-chamber baghouse before the gas was discharged to a stack. The arsenic trioxide was sold or conveyed to an underground storage vault. The roasted calcine was fed to a gravity separation circuit and then subjected to cyanide leaching. Gold was recovered from the filtered leach solution in a Merrill-Crowe zinc precipitation circuit.

Jan 1, 1992

By F. Sime, X. Wang, J. D. Miller, T. Akinseye, S. Assemi, L. Pan

Respirable coal mine dust (RCMD) is a complex mixture of carbonaceous and mineral particles with a variation in size and shape. Accumulation of RCMD in the lungs of underground coal miners results in severe respiratory damage and ultimately progressive pneumoconiosis known as the black lung disease. The occurrence of the black lung disease dropped to a low of 2.1% in 1990s but has increased to 3.1% in 2000s [1], prompting more research on coal mine dust mitigation. In addition to surveying the impact of new mining technologies on the size of generated dust and exposure measurement, a comprehensive characterization of physico-chemical properties of RCMD particles are essential for a better understanding of the adverse health effects of coal mine dust. Such vital factors include particle size, surface charge, morphology, composition, and agglomeration state. The respirable fraction of RCMD, has been designated as particles < 10 μm in diameter, and almost all studies on the RCMD toxicity have focused on micron-sized particles. However, recent toxicological studies have shown that nanoparticles (particles with one dimension less than 100 nm) can have a magnified toxicity compared to the larger particles with the same chemistry [2]. Nanoparticles have a much higher specific surface area compared to the same mass of larger particles and are thus more reactive. Most micron-size particles can be cleared by the body’s defense mechanism. However, inhaled nanoparticles can easily deposit in all regions of the respiratory tract and can translocate to vital organs. [2].

Mar 2, 2022