Search Documents

By L. G. Sobral, J. E. Hoffman, T. J. Keefe, A. J. Monhemius, O&apos

The kinetics of electrodeposition of gold from dilute solutions of alkaline KAu(CN)2 at different gold and free cyanide concentrations on a gold rotating disk electrode were investigated by use of a steady-state linear potential scan technique. The design and performance of a laboratory electrowinning cell with a reticulated nickel cathode, operating in the flow-through mode, for the removal of low levels of gold ions from aqueous cyanide media is described. During the batch recirculation of oxygen-free gold cyanide solutions, the gold concentration was reduced from 10 ppm to <0.5 ppm with current efficiencies of up to 80%. The influence of solution flow rate through the cathode and of the pore size of the reticulated nickel foam is discussed. The removal of gold ions from solutions of low ionic strength was also investigated.

Jan 1, 1993

By C. R. Zegarra

Extraction of manganese, gold, and silver from a low-grade manganiferous-silver ore was investigated by thiourea leaching followed by standard cyanidation. The levels of reagent concentrations in this investigation were 0.0 -1.0 M thiourea and 0.0 -1.0 M sulfuric acid. Temperature and agitation speed were maintained at Z5 °c and 300 rpm, respectively. The dissolution of gold, and silver was shown to be dependent mainly on sulfuric acid and thiourea concentrations. In general, 50.0 % Ag, 98.0 % Au, and 75 % Mn were recovered from a Mn-Ag ore by thiourea leaching. Overall silver extraction of 98.0 % was obtained by cyanidation after thiourea leaching. Thiourea leaching of sodium bisulfite leach residues was also studied, and the total extraction of gold and silver were 97 % and 40 %, respectively. Finally, a two-stage thiourea leach was also investigated.

Jan 1, 1988

By Delbert L. Keenon

The principal concepts of computer control and automation have been successfully applied in industries world-wide, The enthusiasm generated by the proponents of computer control, and the apparent mystery enveloping the techniques of computer control, have caused attention to be focused on this infant industry from all quarters. Consequently, the motivation to "computerize" may be the hope that computers will solve all economic problems. The truth remains that not only have there been monumental successes, but there have been some colossal failures. This paper will attempt to outline a generalized guide to computer control and present methods for avoiding some of the major pitfalls. Since the investment required for computer control systems has been drastically reduced in the past year, small operations will likely find that computerized process control is attractive in areas where it has never been considered before, The discussion presented here is intentionally non-technical and directed towards those who may soon find they have a possible application for a control computer. The primary purpose of computer control is to reduce expenditure and increase profits by improving the quality of product, increasing the efficiency of operation, reducing the materials and man hours required or a combination of these. Success or failure to reach the desired goal depends, to a large degree, on a well-planned approach. This includes recognizing a possible computer application, properly defining the job which is to be accomplished, evaluating computer systems, selecting a capable manufacturer, and following through with sound systems engineering and programming.

Jan 1, 1965

By Qun Wang, Elena A. Alonso, Janusz S. Laskowski

Primary normal long-chain amines are insoluble in saturated brine. Their colloidal solubility (dispersion) in concentrated electrolyte solutions is strongly affected by the presence of surfactants (frothers). This paper shows that a better usage of alcohol type surfactants, which are commonly used in potash ore flotation as frothers, can significantly improve the flotation of both coarse and fine sylvite particles. A new process of potash ore flotation is developed, which includes premixing an effective frother with an aqueous solution of amine or emulsion of extender oil containing amine. With such a combination of flotation reagents, KC1 particles up to 5 mm in size float very well in the short flotation column, and particles up to 2 mm float in a mechanical cell; when used to treat fine fraction-containing sample, this method may as well provide an improved concentrate grade.

Jan 1, 1995

By D. N. Madge

A description will be given of an approach to plant process automation based on the strategy of first developing an information system followed by later development of process models. The advantages of this approach over the unit process control will be outlined. Some insight will be given into the risks associated with this method. These risks can be shown to be primarily economic.&apos; Some reference will be made to two Cominco installations in the interests of illustrating the generality of the information systems approach.

Jan 1, 1972

By T. Kelly

The Cannon Mine is located in Chelan County, near Wenatchee, Washington, at the eastern foot of the Cascade Mountains. The mine is situated about two miles from the Columbia River, in the arid Columbia River Valley. Two hydroelectric dams provide electricity for the area, the Burlington Northern Railroad has a switch yard and loading facilities in Wenatchee. Approximately 25,000 people live in the area. The principal industry is fruit farming. Underground mining techniques are used to provide feed for a 2,000 tpd flotation concentrator at the site. The techniques are low- cost, high productivity methods which allow for a high extraction rate along with a high rate of recovery of the minable reserve.

Jan 1, 1986

By C. B. Manula

Languages such as SIMSCRIPT and GASP have reduced the programming skills required to build simulation models, but not to a level where these can be used by a busy engineer or manager unless he has extensive programming experience. In an attempt to make simulation a more readily available tool, Sanford (1969) structured a generalized materials handling model (UGMHS)* for underground coal mining. The majority of materials handling systems consist of a set of moves and a set of pieces of equipment required to execute the moves. UGMHS gives a technique for describing and classifying the elements in these sets and then a technique for simulating the interactions of these elements as the materials handling system operates. To apply the model, the user simply furnishes data parameters and a fixed set of orders to the computer for his own problem. This new philosophy of dynamic simulation as applied by UGMHS was demonstrated in the paper by Sanford and Manula (1973). A dynamic model of underground coal mining was presented for the purposes of systems design and selection of equipment for a completely new operation and the analysis of existing ones for possible alterations, additions, and general improvements. The main differences between this application and its predecessors is the ability to transport material from multiple mine faces to multiple mine destinations and the ready adaptability to a wide variety of mine layouts. The second difference that characterizes the model is the deterministic simulation of equipment moves according to their mechanical capabilities and the physical profile of the mining scheme. Here, the computer generates performance data in the absence of time studies to compare equipment rather than operator performance.

Jan 1, 1974

By Erik Sundström, Magnus Nygren

Having seen significant improvements to accident rates in the last 40 years, companies in the Swedish mining industry now show a greater focus on the development of safety cultures throughout their organisations and workplaces. However, there is a lack of research examining the different safety initiatives and strategies practiced in the industry today. This study explores the potential influence and consequences such initiatives may have on the development of safety cultures in the Swedish mining industry. Twelve interviews with experts on safety initiatives from four different Swedish mining organisations were conducted and analysed in a process based on qualitative thematic analysis to identify notable connections to safety culture development. The results of these interviews highlight proclivities in the implementation and use of safety initiatives such as subjects of focus, methods and desired effects. This enables the interpretation of the conceptualisation and methods for the development of safety culture in these organisations based on their approaches to safety development. We believe the results of this study can serve as support for discussions on safety culture development in the Swedish mining industry, and be of interest for international mining industries, in addition to approaches to research in this field. However, we also believe it is important to emphasise the opportunities to approach safety culture in mining from different perspectives than those common today.

Jul 19, 2023

By Rodolfo V. de la Cruz

This paper describes the development of a modified Goodman Jack method for determining the mechanical properties of rock masses in situ. The modified method consists of the basic borehole loading device and a friction-strain-gauge measuring module. The friction gauges, located in the central portion of the jack, are impressed on opposite quadrants of the borehole walls and the remaining quadrants are loaded by the borehole jack with a uniaxial self-equilibrating pair of forces. The tangential strains generated at the borehole walls are thus measured concurrently with the loading. For ideal elastic materials, the tangential stresses at any point on the borehole walls due to jack loading can be obtained from closed-form analytical solutions utilizing the complex variable method. Complete stress-strain curves for the rock material can then be directly obtained from the tangential strain measurements and the calculated tangential stresses at those points. The continuous data are considerably more significant and reliable than averaged or point data obtainable by other current in situ measuring techniques. Moreover, the advantages inherent to the original Goodman Jack method are also obtainable in the modified method. The suitability of the new method was demonstrated by carrying out a number of laboratory measurements in large specimens of reinforced concrete, aluminum and granite blocks. The results of actual field measurements carried out in sandstone and granite quarries were found comparable with those obtained in the laboratory.

Jan 1, 1976

By Steve Kral

Competition in the gold mining industry throughout the world has become fierce in recent years. The challenge facing operations personnel is to produce more gold for less money. Likewise, the explorationist&apos;s charge is to find more gold in a more cost-efficient manner. That means using new technology to find new gold deposits and expand present ones. More accurate mapping instruments are available to geologists in the search for new deposits. Advanced geophysical and geochemical methods enable explo¬ration teams to review previously mined districts in their search for minable reserves. Four technical sessions on the geology, exploration, and development of gold deposits were part of the program at `world Gold &apos;89,&apos; a Gold Forum on Technology and Practices," held by SME and The Australasian Institute of Mining and Metallurgy in Reno, NV, Nov. 5-8, 1989.

Jan 1, 1990

By Joseph A. Dos Santos

"The subject of this writing was first published in 1998 with the emphasis on the hardware cost comparison. Other costs, such as the required land area and spatial volume, were mentioned but not emphasized, as these were not deemed as important for new projects where the space was appropriated as required. During the last decade, these other costs have proven to be more than equal in importance. These costs are emphasized here through specific accounts of actual highangle conveyor installations that demonstrate the importance and the high-angle advantage An update on the progress in sandwich belt highangleconveyor technology is also provided.Origin and progress in sandwich belt conveyorsCover belts of the 1950s. Large volume, highangle conveying by “conveyors with cover belt, dates back to the early 1950s, when such systems were employed at the bucket wheel excavator boom conveyor in German lignite mines to increase the depth of cut without increasing the boom length. Various systems were developed, patented and built. These systems were not a lasting success for various reasons, which are noted by Rasper[1]. In his 1958 “Review of Cover Belt Systems,” Rasper summarizes the characteristics which are worth pursing and those that should be abandoned. The former are akin to good conveyor engineering. The sandwich belt conveyor model. The first sandwich belt conveyor model allowed calculation of the required hugging pressure to develop the bulk material’s internal friction and preclude material slideback. A modern, accurate version of the sandwich belt conveyor model is presented in Fig. 1. This model depicts accurately a derating of the material cross-section allowing an ample belt edge distance that can tolerate normal belt misalignment without material spillage. The calculations must thus recognize that only part of the hugging pressure is imparted onto the material with the remainder transferred belt edge to belt edge affecting a material seal. Mathematical development of the sandwich belt model is covered by Dos Santos and Frizzell in their 1983 article, “Evolution of Sandwich Belt High Angle Conveyors.”"

Sep 1, 2016

By N. R. Sainath

This paper discusses a laboratory investigation that studied the microscale flow characteristics of copper ores and the variation in flow behavior resulting from flow of leach solution. Fractures in 40- and 100-mm-diam (1.5- and 4-in.-diam) cores were first mapped by visual inspection. The permeability of cores to water-stressed in a triaxial stress field representative of in situ conditions - was estimated. The samples were then exposed to 20g/L (2.7 oz/gal) sulfuric acid and the experiment was repeated. The porosity and the rate of recovery of copper from the specimen during leaching were also studied. The measured permeability of unleached samples with no visible fractures ranged from 10-16 to 10-19 m2 and it increased as leaching progressed. The porosity increased significantly with leaching, while the rate of copper recovery decreased.

Jan 1, 1994

By Kostas Kaklis, Zach Agioutantis, Robin Flattery

Pillars are used as the primary support structures for underground mining to maintain stability by supporting the over laying strata. In the case of horizontal seams, the pillars are typically subjected to axial loading due to the weight of the overburden and/or abutment stresses, while in the case of inclined seams they are subjected to oblique loading due to both the vertical and horizontal in-situ stress.

By Felicia F. Peng

One of the serious environmental problems related with the extraction of coal for carbon and energy resources is that upon preparation of coal a large quantity of fine coal has been discarded and/or lost to tailing impoundments. These problems present hazardous conditions to the local community. Also, the precious heating value of energy resources has been wasted and Left unrecovered in the tailing impoundments. Both RCR and SMRC ACTs recognize and mandate an investigation into slurry impoundment problems, including consideration of potential use of those coal fines in the tailing ponds. Bituminous coal producing district 46 encompasses the northern panhandle of West Virginia. The major producing seam in this district is the Pittsburgh coal, 1-7 meters thick. 75 percent of the coal producted in this district is deep mine. This district produces approximately 3 million tons of coal waste materials annually. One of the coal preparation plants in the district which we have visited has been processing Pittsburgh too. 8 seam coal for the past ten years. The characteristic data of the Pittsburgh raw coal is shown in Table 1. The raw coal produced in this district is characterized by its high heating value, high ash and high sulfur contents. The coal preparation plant flowsheet designed and used to process this Pittsburgh raw coal prior to 1979 is shown in Figure 1. It was a partial coal cleaning plant&apos; with 1 092 mt/hr designed capacity, which consisted mainly of a coarse coal cleaning circuit. The rejected fine particles in the size range of -600µm which consisted of vorsiv underflow and cyclone underflow from clean coal streams and spiral classifier overflow from refuse stream were settled down in a thickener with the aid of anionic flocculant prior to being pumped to the tailing ponds for disposal. Figure 2 shows that the same coal preparation plant in Figure 1 was modified to a semi-complete coal cleaning plant and expanded its designed capacity to 1 820 mt/hr, when market of coal fines becomes feasible in 1979. Tabling in the clean coal circuit and thermal dryer in the dewatering circuit were added to the flow sheet. The purpose is to recover more coal fines, reduce more pyritic sulfur and ash contents in coal and also to reduce solid waste material to be stored into the slurry impoundment, giving them a Longer Life. The rejected fine particles fed to the thickener are clean coal fines from two cyclone overflows and the fine refuse from the rufuse cyclone overflow. The clean coal fines presently lost to the tailing impoundments are in the size range of -150 µm and constitute about 5 percent of the overall plant feed. Total amount of tailing waste material accumulated in a tailing impoundment is estimated at 1.3 million metricton for the past ten years.

Jan 1, 1982

By Jan M. Mutmansky

30.1-THE SCOPE OF SYSTEMS ENGINEERING JAN M. MUTMANSKY JAN M. MUTMANSKY 30.1.1-DEFINITIONS The terms "systems engineering," "systems analysis," and "operations research," common in today&apos;s technical literature, often are interchanged because of their similar meanings. However, some differences exist which need explanation. The most convenient way to achieve an understanding of the differences is to start with the definition of a system, namely, a collection of components which interact in a specific manner to accomplish a common objective. Accordingly, a haulage truck, a computer, a missile, a mining company or a nation each may be considered a system. Systems engineering generally can be defined as the conception, planning, design and engineering of any system of interacting elements so that the objective of the system is automatically optimized. Thus, systems engineering normally is con¬cerned with systems not yet activated.&apos;,&apos; Systems analysis may be described as a scientific method of making decisions based on a quantitative or other objective evaluation of all action alternatives. It is very similar to systems engineering but usually is not considered to be restricted to problems of design prior to use. While the previous two disciplines are somewhat vague and can encompass a great variety of engineering functions, operations research can be more specifically defined as the application of mathematical models to the problem of optimizing the objective of any predefined system. Systems analysis and systems engineering are closely aligned sciences but opera¬tions research differs in the following ways. First, it generally is associated specifically¬with optimization and mathematical models while the other two often are not. In addition, it, is used predominantly on well-defined problems which can be ex¬pressed in mathematical terms. However, systems engineering or systems analysis may deal with highly complex social or governmental systems which may be ill¬defined and unsolvable by the classical methods of operations research. Finally, systems analysis and engineering always strive to look at the entire system to avoid the problem of suboptimization often necessary in operations research because of the necessity for a mathematical model. Because of his more extensive system, however, the systems engineer often is less able to find the optimal system. In summary, operations research, systems analysis and systems engineering are very similar in purpose but one, operations research, is more mathematical in nature and forms an important part of the other two activities. Other definitions which may be helpful are provided by Griffiths 3 Wilson,4 Falkic 5 Hall,2 Quade and Boucher, 6 and Flagle et al. 1 30.1.2-METHOD AND TECHNIQUES The systems or operations research approach makes use of scientific problem solving. The basic procedure comprises the following general steps: 1. Definition of the problem. 2. Construction of a model of the system. 3. Testing of the model under known conditions.

Jan 1, 1973

By Felicia F. Peng

An economic analysis for evaluating coal preparation plants in the Appalachian Region is presented. A complete coal preparation plant which includes multi-streams and/or multi-stages coal cleaning circuits, complete closed water circuits, environmentally acceptable refuse disposal and reclamation systems is used to determine the capital and operating costs. The plant is capable of producing metallurgical grade clean coal or deep cleaned steam grade coal for future power generating plants use. Utilizing a profit maximization as a decision criterion, an optimal yield, and optimal coal clean¬ing circuits, closed water circuits, and disposal and reclamation systems for a given coal characteristic may be selected among the process alternatives by using a process simulation-economic model of the coal preparation plant. A deterministic analysis is used to calculate the discounted-cash-flow interest rate of return (DCFIROR) and project the selling prices, and determine the Return on Investment (ROI) for the cases of 32.65% and 52.74% plant utilization with producing two cleaned products. Sensitivity analyses are performed to quantify the effect of total capital investment, operating cost, run-of-mine cost and yield on an economic criterion-ROI and selling prices. A probabilistic evaluation using the Monte Carlo simulation technique is further made to quantify the risk involved in obtaining the desired profit levels. The results of the economic analysis for a given coal preparation plant configuration and characteristics of raw coal indicates that the selling prices of producing two cleaned products are greatly affected by the change in percent of plant utilization (production schedule), yield, and run-of-mine cost, and total capital cost. The sensitivity analysis also shows that the total capital investments has a three times greater effect on required selling prices than operating costs. The risk analysis shown that the overall economics look very attractive with current coal sale prices and 52.74% plant utilization.

Jan 1, 1979

By B. R. Benner

Progressive improvements in crusher design, screening efficiency, and operating experience along with the downsizing of many taconite operations has resulted in the abilitv of some crushing plants to produce a substantially finer product. This finer product opens the possibility of replacing the rods in the rod mill with balls as is the current practice at Sydvaranger, Norway. If this replacement could be accomplished substantial savings associated with metal wear and the elimination of rod charging may be realized. The purpose of this study was to compare the performance of a mill charged with rods with the performance of the same mill charged with balls at the pilot scale. The first objective was to establish whether we could achieve the same throughput rate at the same mesh-of-grind in a mill in which the rod media has been replaced by balls. The second point was to determine whether the ball media would create a significant tramp oversize problem.

Jan 1, 1990

By Howard M. Wells

Portfolio theory and the Capital Asset Pricing Model (Modigliani and Pogue, 1974) provides an investment decision rationale which takes account of the benefits of diversification in reducing effective risk, but this theory does not consider the financial capability of the firm to survive large losses if they should occur. The LL-curve theory (Wells, 1976) takes the latter consideration into account, but it does not provide for the effects of diversification. This paper pro- poses a general theory to account for both diversification and the financial capacity of the firm to underwrite the investment risks.

Jan 1, 1983

By Fritz F. Prugger

This paper considers some of the main aspects of underground mining in the flat, rich, but deep lying deposits of Saskatchewan. It briefly describes the pertinent geological features as they relate co mining and the practical de-stressing techniques used to allow productive extraction in the high stress environment present in many of the province&apos;s mines. Fining layouts, materials handling and the evolution of some of the world&apos;s largest mining equipment are examined.

Jan 1, 1980

By Robert A. Cummings

Disintegration of the immediate shale roof in coal mines interferes with ventilation, production, and safety. The effect is seasonal and correlates with high levels of moisture in the intake ventilation air. Disintegration, though not completely understood, is caused by shale dilation and weakening upon exposure to atmospheric moisture. Fluctuating moisture conditions are particularly deleterious, and may be at least partially controlled by "tempering" the air before it is brought to the working places. Roof behavior was studied in an operating mine during a 12-month monitoring period. This approach can be used in developing criteria to reduce or prevent shale roof deterioration.

Jan 1, 1981