Search Documents

By C. W. Schultz

The Alabama tar sands of the Hartselle Sandstone formation present a more difficult problem in primary extraction than do the Athabasca tar sands. In contrast to the Athabasca tar sands, the Alabama tar sands are "oil wetted" and the contained tar, or bitumen, is of much higher viscosity. A physical beneficiation scheme was developed in which clean sand from an external source was used as a scrubbing medium. High intensity scrubbing liberated the tars which are readily recovered by froth flotation. Locked cycle tests have shown that, after the use of an initial ration of clean sand, the system produced enough new clean sand to be self sustaining.

Jan 1, 1992

By J. C. Irvine

Meramec Mining Company, a joint venture by Bethlehem Steel Corporation and St. Joe Minerals Corporation, is engaged in the mining, concentrating, and pelletizing of iron ore from the Pea Ridge Mine located near Sullivan, Missouri, about 70 miles southwest of St. Louis. The orebody was delineated in the mid-1950's by St. Joe during an exploration program to discover new lead orebodies. An airborne magnetometer survey which was run by the U. S. Geological Survey, the Missouri Geological Survey, and several min¬ing companies was published in 1950 and showed an anomaly in the Pea Ridge area. Test holes drilled in 1953 and 1954 revealed the presence of a large orebody of probable commercial significance; additional drilling in 1956 and 1957 provided confirmation of this. Meramec Mining Company was incorporated in 1957 and shaft sinking began in the latter part of that year. The Pea Ridge orebody lies under about 1300 feet of sediments. It is tabular, about 2600 feet long and up to 600 feet thick, and lies in an approximate east-west delineation. The orebody dips about 800S and is of unknown depth. The ore is primarily high grade magnetite with smaller zones of specular hematite, The Pre-cambrian wall rock is rhyolite porphyry. The mine is serviced through two concrete-lined shafts, 19 feet 1 inch in diameter and 2500 feet deep. No. 1 shaft, equipped with an "A" type head-

Jan 1, 1972

By Harland E. Cofer

A computer-assisted resources and sedimentological study of the Andersonville, Georgia kaolin-bauxite district was begun in 1975 under a grant from the Office of Mineral Resources of the U.S. Geological Survey (Grant # 14-08-1110-G-173). A preliminary report on the kaolin and bauxite resources of the district has been placed on open file at the U.S.G.S. in Reston, Virginia; the Georgia-Geological Survey in Atlanta, Georgia; and Georgia Southwestern College in Americus, Georgia. In addition to a resources estimate, the objectives include the determination of the mineralogical variation, sedimentological parameters, and paleogeographic patterns of the deposition of the high alumina materials and their associated sediments. In the process of compiling data for the resources estimate, isopach maps were developed that provide information as to the shape, size, and distribution of the kaolin deposits and the kaolinitic sediments that contain them. These or similar maps developed for other districts can be useful exploration tools.

Jan 1, 1977

By F. W. Petersen

Slurry reactors are being used extensively throughout the chemical, biochemical and mineral processing industries. This paper describes the interaction between fine ore particles and granular porous adsorbents such as activated carbon and ion-exchange resins in a stirred tank reactor. Gold and silver cyanides were used as adsorbates to detect changes in the mass transfer characteristics of the adsorbents, which were ashed to determine the loading of ore particles. A simple kinetic model incorporating film diffusion, intrapanicle diffusion ~d the adsorption equilibrium, was used to interpret kinetic data and to estimate the effect of slurry conditions on the diffusion parameters. It was observed that the equilibrium loading of fines in the adsorbents was independent of their concentration in the slurry. Furthermore, the presence of these panicles inside an adsorbent decreases the effective diffusion of gold or silver cyanides into the adsorbent matrix. When fine suspended solids are present in the reactor, a decrease in the effective availability of the superficial surface of the pre-saturated adsorbent panicles for mass transfer from the liquid phase was observed. This newly defined surface availability factor was dependent on the concentration, panicle size, and the zeta potential of the fine particles in suspension.

Jan 1, 1993

By I. H. Douglas

All grade control methods in use currently by the mining industry are imprecise. The methods suffer from being locally inaccurate, leading to are loss and contact dilution. An ore/waste indicator variable can be used to predict the probability of ore occurrence at a given location, Po. Then, an ore grade Zo for an ore location and a waste grade Zw for a waste location are obtained. The expected revenue is calculated at each location, based on its probability of being are or waste, the corresponding grade, and on the cost of mining and processing the ore or the waste. Finally, the decision of whether to recover the block is based on the expected revenue value for that block. The method is illustrated with an example taken from the Jerritt Canyon district in northeastern Nevada.

Jan 1, 1994

By B. A. Waite

The new OSH regulations concerning ground ward monitoring of underground coal mines has been the source of many concerns for the mining industry. Because the regulations were initially written at the federal level but are being administered at the state level, considerable confusion exists within the industry as to what is actually required. Based on the preparation and submission of over 30 monitoring plans for existing deep mines in Pennsylvania, West Virginia, and Ohio, we now have a very good feel for the detail the monitoring plans, as well as the costs to im plement the plans. We do not, however, feel confident in our evaluations of the long-term impact the ground water monitoring regulations may have on the industry.

Jan 1, 1980

By Harvey P. Knudsen

This paper describes the results of a comparative study of the geostatistical ore reserve estimation method over three conventional methods; the polygon method, the inverse of the distance squared (IDS) method, and ELIP which is similar to IDS. Each method was evaluated on its ability to accurately predict individual block grades for one bench of the Pima Nine, located near Tucson, Arizona. Results at the Pima Mine indicate that the geostatistical method is no better nor worse in predicting block grades and total tonnage than the ELIP or IDS methods in contrast, the polygon method is clearly inferior. All of the methods would have given better results if geology had been included in the block model. At already producing mines ELlP or IDS may be good choices since they involve substantially less cost in computer time. For prospective or new properties, the geostatistical model is more attractive, due to its ability to construct confidence limits on the estimates.

Jan 1, 1976

By George O. Lower

The use of cyanides in the extraction of gold and silver is well known.1 Such extractions employ con¬centrations of cyanide in the range of 0.02-0.25 % sodium cyanide equivalent in leaching cycles of 24-48 hours and frequently longer. Copper minerals, even though minor components of precious metal ores, dissolve in these cyanide leaching solutions, consume cyanide, cause fouling of mill solutions, and thus interfere with the precipitation and recovery of gold and silver. 2,3,4 This paper presents a summary of laboratory investigations on the use of cyanide solutions as extractants for copper from various copper-bearing ore fractions. In view of the metal contents involved, it will be apparent that larger quantities of cyanide are required to extract copper than for the extraction of precious metals. In cyanide solutions of concentrations generally favorable to copper extraction, sulfide and oxide copper minerals were found to dissolve rapidly at room temperature and atmospheric pressure. For example, on products in the flotation size range, the major portions (e.g. 65-85%) of the extractable copper frequently dissolved in 2-10 minutes. At coarser grinds, e.g. 100% minus 28 mesh and 100% minus 10 mesh, 75-85% of the total copper was extracted in 30 minutes.

Jan 1, 1966

By Mingju Liu

The coal and gas outburst accident on May 20, 2007 at Sihe Coal Mine is unique in that there was no or very little soft coal in the coal seam and that the coal strength was very high. The outburst also showed that there was a very high gas content of 20-30 m3/t in the coal seam nearby the outburst site. Based on the field test and observations, together with laboratory experiments, detailed analysis was conducted on the controlling factors of coal and gas outburst potential at Sihe Coal Mine. Stress data available from Sihe Coal Mine, northern China, and other parts of the world, were also taken into account to facilitate the analysis. The results shows that the stress level was not abnormal compared to other coal fields in China prone to outbursts, and that gas contained in the coal seam was the main factor that triggered the outburst. All these factors were essentially controlled by the tectonic evolution features in Qinshui Coal Basin, to the Southeast of which Sihe coal field is located. Based on the analysis, assessment of coal seam outburst potential was carried out by measurements of coal seam gas contents, observation, and detection of soft coal layers in the coal seam. The results show that outbursts are limited to only a small part of the whole coal seam and that the eastern part of coal field is not prone to outbursts.

Jan 1, 2009

By Phil Dakin, Rajiv Chandramohan, John Lo Grande, Greg Lane

Crushing and grinding circuit availability is a critical design factor defining the installed equipment selection and the process buffers required to maintain throughput during maintenance. The comminution circuit typically accounts for a process plant’s largest capital expenditure and energy use. Effective process and equipment selection and layout optimization are crucial steps when combining the objectives of cost-effective design and high circuit availability in operation. This paper outlines fit-for-purpose design principles for optimizing process flow, eliminating standby equipment and reducing buffer residence time whilst improving maintainability and operability.

Feb 1, 2025

The 1996 Arizona Conference was held in Tucson on Dec. 8 and 9. Attendance was 648, a 12% increase from the 1995 conference. The annual conference is organized by the Arizona Conference Board of Directors, representing SME sections from throughout Arizona and adjacent areas. In addition to those representing mining and processing operations in the Arizona region, the meeting was well attended by interested parties from throughout North America. These included vendors, consultants, academia, research organizations and corporate management. The technical program highlighted the meeting. It consisted of a keynote address and morning and afternoon technical sessions. In the technical sessions, 23 papers were presented by the mining, hydrometallurgical, smelting, geology and mineral-processing divisions. The conference was then capped by a banquet that included a talk by a noted economist. Keynote address The program was kicked off by a keynote address titled "Forecasting for the 105th Congress," by Rep. John Shadegg (R-AZ). He was elected to Arizona's Fourth Congressional District in 1994. Shadegg serves on the House Budget Committee, the Resources Committee and the watchdog Government Reform Committee. He stressed the familiar conservative positions of reducing government spending, balancing the budget and states rights. As a member of the House Resources Committee, Shadegg stated his support for the mining industry. Technical sessions Mining division. Two of the five presentations described developments at two Arizona mining operations. T.J. Swendseid of Phelps Dodge presented a paper titled "New developments at Morenci" and P. Garretson of BHP presented a paper titled "Startup of the Robinson Project." Morenci continues to expand its operation and recently broke records for production. Other developments at Morenci included the completion of a 600-m (2,000-ft) drainage tunnel and stockpile rehandling. In addition, Phelps Dodge moved Morenci's crusher plant. It was completely disassembled and reassembled in just eight days. Another interesting presentation was "Predictive maintenance techniques for large electric shovels at Cyprus Sierrita," presented by T. Ritzel of Cyprus Amax. The presentation described high-technology methods for predicting maintenance problems. These methods included vibration analysis, ultrasonic detection, infrared thermography, electrical measurements and tribology (the science of lubricant evaluation). The benefits of these techniques are reduced downtime of the equipment, as was demonstrated in case studies at the mine. The other presentations were "Introduction to NOSA 5-star safety program," by R. McKinnon, BHP Copper North America, and "A new design guideline for mine sealing," by K. Fuenkajorn, Rock Engineering International. Hydrometallurgical division. The hydrometallurgical session consisted of five papers. These included a presentation titled "Recovery of gold and silver using guanidine-based extractants," by M. Vining of Henkel Corp., Tucson, AZ. In this presentation, guanidine-based extractants LIX-79 and AURIX resin were introduced. LIX-79 was shown to have applications in copper-gold and high silver ores. In ammonia-cyanide leaching, AURIX was shown to be more selective in CIL vs. RIL comparisons. Other papers in the hydrometallurgical division included "Application of cobalt in the copper industry," by J. Hawke, OMG Apex Inc.; "Series parallel conversions and production gains at Cyprus Miami Mining's dump leach and solvent extraction operation," by E. Bilson of Cyprus Amax; "Lead alloy anode corrosion at the San Manuel SXEW tankhouse," by W .M. Gort of BHP Copper and "Hydrometallurgical treatment of copper refinery slimes," by B.C. Wesstrom of Phelps Dodge. Smelting division. Three papers were presented in the smelting division session. These included updates and reports on improvements at the Hayden, Hidalgo and BHP San Manuel smelters. For example, W.A. Dutton of Phelps Dodge presented "Recent improvements at the Hidalgo Smelter." These changes were aimed at reducing environmental emissions and increasing production. They included modifications to the fugitive-gas collection system to reduce particulate emissions, rubber lining the acid plant scrubbers to reduce corrosion and the installation of a cold lime softening system for water treatment. Equally interesting papers were presented by D. Norton of Asarco, Hayden, AZ, in a paper titled "Update of the Hayden smelter process," and by D. Jones of BHP Copper, San Manuel, AZ, in a paper titled "Update on first campaign of the BHP San Manuel Copper." Geology division. The session began with a paper that outlined the progress of an exploration project in South America. "The Pierina exploration project, Ancash Province, Peru" was presented by J.D. Lowell, Lowell Mineral Exploration, Rio Rico, AZ. Another paper was then presented on a copper deposit in Grant County, New Mexico. "Zonation of supergene copper minerals at Hanover Mountain, Grant

Jan 1, 1997

By S. S. Pathak, S. Mishra, M. H. Tyeb, A. K. Majumder

Roping in hydrocyclones is a well-known phenomenon in mining and mineral industries which put serious restrictions on their continuous and maintenance free operation. Roping is mostly observed in association with high underflow solid concentrations which can be attributed to higher fraction of solids reporting to the underflow or the feed solid concentration itself being higher. This paper proposes a newly designed spigot with a truncated conical geometry which can allow for a rope-free discharge at higher feed solid concentrations. The experimental observations revealed that in the operation of a 50.8-mm-diameter hydrocyclone, roping ensued at 10% to 12.5% (wt%) feed solid concentration depending on feed inlet pressure for the cylindrical spigot, whereas with the modified spigot, rope free discharge was attained even at 25% (wt%) feed solid concentration.

Jan 8, 2022

By Paul H. Johnson

Resource Engineering and Development, Inc. is designing and building a portable 150 to 225 TPD, flotation-cyanide leach plant with unitized, skid-mounted components. This plant design, with its portability, low capital investment, and high recovery of silver and gold from many partially oxidized ores, is well suited to treat many small, high-grade deposits, old waste dumps, and old mill tailing piles. A description is given of flotation and/or cyanide leach tests run on about 17 partially oxidized, newly mined ores; waste dump materials; placer slimes; and old mill tailings.

Jan 1, 1981

By Jerry R. Riding

Metallurgical process methods have seen dramatic improvement over the past fifty years. As these improvements have come about, more and more emphasis has been placed on obtaining accurate and rapid analysis of the metallurgical processes. Well-defined conventional laboratory analysis procedures which have proven to be reliable were developed early in the mineral industry's history; however, these conventional procedures, which have not changed appreciably in fifty years, have the serious drawback that they are too slow to be of appreciable value in automatic control of the processes. For example, the assay results normally become available to a mill operator from eight to twenty-four hours after a sample is taken. Since the desired mineral separation can only be made while the minerals are in the flotation circuit, conventional assay results provide information similar to postmortem reports. Consequently, using conventional procedures, the mill is operated with information from an earlier period of time, which may not reflect current conditions. In recent years there has been a steady increase in the volume of required samples. At the same time, labor, material, and overhead costs have continued to rise causing the cost per assay to reach an alarming level. This rising cost per assay, plus the increasing demand for rapid analysis necessary for control, has caused the mining and metal processing industries to look toward other techniques to solve these problems As a result, X-ray fluorescence which can provide on-stream analysis necessary for control, as well as perform numerous laboratory assays at lower cost and at a much greater speed than conventional methods, has gained wide-spread attention. In addition, multichannel X-ray fluorescent instruments are now available which have been perfected to the point where the analysis of the most important chemical constituents is available within one minute after a sample is presented to the X-ray analyzer. Because of these obvious advantages, extensive use is being made today of X-ray analysis in the mining industry to analyze slags, ores, and mineral content of rocks. The results are used to make quick decisions for both mining and beneficiation of metals. For example, X-ray systems which provide rapid on-stream analysis of the slurries at desired points Fn metallurgical processes have recently been developed. The successful application of these systems has moved the milling process a step closer to fully automatic control.

Jan 1, 1969

By T. Cyrul

The Polish underground mining has its long lasting tradition. High production of coal, that has recently been approaching 200 milion tons per year, put this small country among the bigest world producers of coal. To achieve such a high production, which mainly originate from very unfavourable mining and geological conditions, Polish scientists and engineers have to introduce new and original solutions to the mining practice. Many of the solutions on mining methods, ventilation, stability, subsidence etc., have had the world wide reputation, however, insufficient translations from Polish cause , that many of the recent Polish mining achievements are not known to foreign specialists.

Jan 1, 1986

By V. K. Gupta

The phenomenon of zero order production of fines associated with the batch comminution of monosize feeds in tumbling mills has been examined in the context of the size discretized population balance model. It has been shown that the model admits zero order production kinetics only in an approximate sense. The necessary and sufficient conditions for approximate zero order production of fines have been obtained. As these conditions cannot be expressed in terms of the model parameters Sj and Bi,j alone,. several examples have been used to illustrate some of the important characteristics of the zero order production systems. One of the important characteristics of these systems has been identified as a "weak necessary condition", and the other as a " favourable condition ".

Jan 1, 1985

By C. D. Litton, I. E. Perera

This report presents the results of experiments to evaluate different types of mine fire sensors in an underground mine environment using a commercially available atmospheric monitoring system. To determine how well carbon monoxide (CO) and smoke sensors respond for purposes of fire detection, experiments were conducted using test fires of different mine combustibles and for both flaming and nonflaming combustion. The experiments were designed to assess the response of fire sensors to different contaminants and different contaminant levels produced from the test fires. The experiments were performed in the Safety Research Coal Mine at the U.S. National Institute for Occupational Safety and Health’s Bruceton Research Facility in the presence of an average ventilating air velocity of 1.6 m/s (315 fpm). Five fire sensor stations were located downstream of the test fire at fixed locations, with each sensor station consisting of four sensors: a CO fire sensor and three different smoke sensors, of which two were evaluated by the Mine Safety and Health Administration (MSHA) for intrinsic safety and the third was used extensively in underground mines overseas but not evaluated by MSHA for intrinsic safety. All four sensors were mounted near the center of the entry and in the upper onethird of the entry height. A UL-listed combination ionization and photoelectric smoke sensor was mounted near the roof at the first sensor station and its responses were compared against the responses of the four CO and smoke fire sensors. Sensor response data, contaminant travel times, and the impact of fire on the existing ventilation flow are discussed as they apply to earlywarning fire detection. Of significance in the analysis is the need for performance standards for mine fire sensors in order to provide for consistent and timely early warning of developing fires.

Jan 1, 2014

By George C. Toland

Most existing impoundment ponds and dams leak effluent into the soil or rock upon which they are constructed. However, proposed environmental legislation will require very stringent control on the release of toxic effluents such as cyanide. More exacting investigation, design, and construction techniques than have been used in the past will be required to satisfy these new regulations. This paper discusses the types of field and laboratory investigations required to develop the data for the design of an impoundment system containing toxic effluent, and discusses in detail technical considerations necessary to design this system. Design topics include reservoir sealing with natural and man-made materials; embankment sealing; embankment design considering stability, surface hydrology, capacity, and downstream catchment basins; and special implications of cyanide effluents.

Jan 1, 1975

By S. M. Moore, J. F. Burr, R. Fernando, D. Snyder

"The Mine Improvement and New Emergency Response Act of 2006 (MINER Act Public Law 109-236) was passed by Congress in response to three major underground coal mine accidents in the United States that claimed the lives of 19 miners. The Act resulted in substantial changes in the underground coal industry relative to the use of technology for mine escape, rescue, disaster response and other areas where the lack of these technologies contributed to the fatalities caused by these tragedies. This year marks the 10th anniversary of the MINER Act, which makes it an opportune time to reflect on the events that led to its passage, the changes that have been made since then, and the work that remains to be done. As discussed below, the last decade has demonstrated tremendous cooperative efforts among mining operators, technology innovators, labor, The National Institute for Occupational Safety and Health (NIOSH), the U.S. Mine Safety and Health Administration (MSHA) and state regulators, resulting in substantial improvement of the technologies used for escape and rescue and noteworthy progress toward meeting many of the goals of the MINER Act. While the MINER Act and this article pertain primarily to coal mining, many of the technologies are equally applicable to any underground mining and have already found some acceptance outside of coal. TECHNOLOGY GAPS TARGETED BY THE MINER ACT The MINER Act addressed several technology challenges: • Problems with donning and switching between self-contained self-rescuers (SCSRs). • Poor visibility in smoke. • No wayfinding assistance for escape from the mine. • Limited breathable air supply. • Inability to locate trapped miners. • Inability to communicate with trapped miners. • Failure of mine seals. The MINER Act had several provisions that prescribed specific safety technologies intended to address these issues. Many of these were directed at post-accident technology requirements — an area in which Congress mandated additional technology investment. Specifically, the Act required mine operators to submit emergency response plans (ERPs) that contained provisions for implementing new or improved post-accident communications, tracking, lifelines, refuge alternatives and breathable air supplies along with training for emergency procedures and local coordination of emergency response. Most of the requirements were to be carried out within three years of the ratification of the MINER Act. In addition to these requirements for mine operators, the Act clarified and expanded NIOSH’s role and authority in enhancing the development of new mine safety technologies and expediting their commercial availability. The MINER Act also required NIOSH to develop research on refuge chambers, mine seals and the use of belt air and fire-retardant belts. Mine seals had to be upgraded and MSHA turned to NIOSH for applied research to establish the new explosion-resistance requirements. Progress toward closing the gaps."

Jan 1, 2017

By B. S. Graves

Deep well disposal of selected industrial wastes has been proved feasible and acceptable in the New Orleans area by several industries including Shell Oil Company's Norco Refinery and Chemical Plant where three of the six successful disposal wells in this area are operating. Well design and procedures for restoration of capacity are based, in most cases, on the principles of brine injection developed by oil producers in South Louisiana. Geological formations in the Gulf Coast area are suited to this type of injection because receiving strata are porous, isolated from sources of potable water and their water is compatible with the liquid wastes to be injected. This method of disposal is a simple, complete and economical solution to the problems presented by certain hard to treat wastes.

Jan 1, 1964