Search Documents

By D. F. Scott

Spokane Research Center personnel have been investigating the use of seismic tomography to monitor the behavior of a rock mass, detect hazardous ground conditions, and assess the mechanical integrity of a rock mass affected by mining. Seismic tomography can be a valuable tool for determining relative stress in deep (> 1220 m) underground pillars. If high-stress areas are detected, they can be destressed prior to development or avoided. High-stress areas can be monitored with successive seismic surveys to determine if stress decreases to a level where development can be initiated safely. There are several benefits to using seismic tomography to identify high stress in deep underground pillars. The technique is reliable, cost-effective, efficient, and non-invasive. Also, investigators can monitor large rock masses, as well as monitor pillars during the mining cycle. By identifying areas of high stress, engineers will be able to assure that miners are working in a safer environment.

Jan 1, 1997

By Jaisen Kohmuench, Michael J. Mankosa

Flotation has long served as the foundation for sulfide mineral recovery. As ore grades decline, however, this traditional approach is being pushed to the limit. Nowhere is this more evident than in the challenge of recovering coarse, partially liberated particles — an area where conventional flotation systems typically underperform due to excessive turbulence. As a result, valuable coarse minerals are often lost to tailings. Fine grinding has become the default solution, although with the added burden of higher operating costs and more challenging tailings disposal. To address the challenge of coarse particle recovery, Eriez developed the HydroFloat, a technology that uses a novel fluidized-bed approach to extend the upper particle size range of flotation significantly. The HydroFloat can recover particles exceeding 0.5 mm in diameter with a sulfide surface expression as little as 2 percent. Coarse particle recovery allows for optimization of comminution circuits for coarse gangue rejection before fine grinding. A substantial increase in overall tailings particle size provides higher water recovery due to improved drainage and allows for consideration of a dry, stacked tailings option instead of a tailings dam/impoundment. The technology’s transformative potential has not gone unnoticed. In recognition of its impact, Eriez was honored with the 2024 Robert E. Murray Innovation Award, commonly referred to as the Murray Award, by the Society for Mining, Metallurgy & Exploration. This prestigious award was established in 2017 to recognize organizations that advance the mining industry through the implementation of technical innovation. The HydroFloat stands as a fitting example of how creative thinking and industry collaboration can solve long-standing technical challenges.

Oct 1, 2025

By E. J. Wasp

The transportation of mine products incurs a cost which can have a significant bearing on the competitive position of the manufactured product. Clearly, the engineer who is responsible for selecting a mode of transport must base his decision, at least in large measure, on economic comparisons. And today, the engineer usually finds that he has to choose between several modes, including slurry pipelines. For the purpose of an initial economic screening, it is not necessary to go deeply into the technical details of a slurry system. What is usually needed, however, is a method with which the engineer can make a quick economic assessment to determine whether a slurry pipeline should be included in the detailed final analysis. This paper presents a rapid method for making such a preliminary appraisal. Experience with commercial slurry pipeline systems in several countries and with a variety of solid materials has shown that if several assumptions pertaining to critical design variables are made, it is possible to roughly estimate the transportation cost of a slurry system on the basis of only three factors: the specific gravity of the solid material, the length of the system, and the quantity of slurry to be pumped each year. It is assumed that conditions pertaining to field construction, corrosion inhibition, and the like, will be favorable. This assumption is critical because any factor which analysis shows to be particularly unfavorable will raise the total transportation cost estimate which this paper establishes. If the engineer employs this estimating procedure and decides that the use of a slurry pipeline is economically unattractive, his chances of being wrong are small. Conversely, if his quick appraisal indicates that the use of a slurry system is economically favorable, the engineer is justified in committing the time and money needed to make a more detailed investigation of the slurry pipeline potential.

Jan 1, 1969

By ZHONGLING ZHAO, WANTING SONG, GUOZHONG LIU, LEIXIN SHI, ZUI WANG, YUANYUAN LIU, KE GAO, DONGHONG JIANG, WANG LUO, PEICHAO LU, Jianwei Cheng, WANCHENG ZHENG, Gang Zhao, YUNGANG WANG, JIANBING ZHAO

Coal spontaneous combustion is one of the major disasters in coal mines, and it can have devastating effects on the normal mining and production activities of mines. This paper presents the field investigation, field measurement, data analysis, and formulation of fire-extinguishing measures conducted to extinguish the fire from a coal spontaneous combustion incident that occurred in a high-gas coal mine in China.

By T. W. Martin

The use of conveyors in large, open pit mines and their drawbacks are discussed. Technological developments such as long distance conveyors capable of handling large rocks are explored. The development and testing by the Bureau of Mines of a prototype crib and cable conveyor for handling large rocks are discussed, and possible modifications of the concept for a production model are examined.

Jan 1, 1984

By M. E. Rossi

This paper discusses the use of Conditional Simulation (CS) models to provide mill feed grade profiles for different time periods. The conventional approach of classifying block estimates as ore or waste generally does not adequately represent dilution, lost ore and the anticipated grade control data, including variability of mill feed from the pit and possible stockpiles. The detailed simulation of grade control practices can be done, but at the Pre- or Feasibility stage of the project may be impractical, since drawing dig limits on multiple benches is tedious and time consuming. Using the Feasibility Grade Control (FGC) method as developed by the Centre for Computational Geostatistics (CCG, University of Alberta-Edmonton), the CS models can be processed quickly to establish dilution and lost ore, and predict daily or short-term feed to the mill. The simulated nodes can be aggregated into selective mining units with adequate representation of likely geometries to be recovered from the pit, to mimic anticipated selectivity. An example from a large copper deposit is shown. The study provides an estimated stream of tonnages and grades fed to the plant by mining periods of interest and based on a specific mine design and schedule. The resulting cash flows support the economic and financial analyses of the Feasibility Study; also leads to improving mine schedules; and aids in developing blending schemes if necessary. INTRODUCTION The conventional approach of separating mineralized material into ore or waste categories does not always include a realistic amount of dilution and ore loss. Also, often it does not provide a good estimate of the grade that will be fed to the mill. If the grade control estimates are unbiased, they will over the long run represent the long-term average of grades fed to the mill; but the anticipated variability of mill feed from the pit and stockpile sources may be misrepresented. Some references on traditional grade control implementations can be found in Chunnett (1982); Davis et al. (1989); Srivastava et al. (1992); and Nowak (1992). Alternative methods based on economic variables improved significantly on the purely grade-based control methods, see Douglas et al. (1994). Further developments involved the use of geostatistical conditional simulations (CS) and profit models, which in several cases have been successfully implemented (Aguilar and Rossi, 1996; Rossi, 1997; Deutsch et al., 2000; Norrena and Deutsch, 2002; Neufeld, 2005; Jewbali and Dimitrakopoulos, 2009). But they can be impractical, mostly due to the lack of understanding of the methodology involved; even if semi-automatic dig limit drawing is implemented, there is always a need for is tedious and time consuming checking and corrections, even if using a single profit model derived from the simulated grades.

Jan 1, 2019

By S. C. Termes

As part of an effort to provide basic data on the fundamental scientific and engineering principles of minerals beneficiation, the Bureau of Mines is conducting research on the flocculation of mineral fines. This paper presents results of studies using crosslinked starches containing carboxyl, diethanolamine, iminodiacetic acid, and xanthate groups to flocculate hematite, goethite, chromite, manganrte, pyrolusite, cuprite, and cassiterite fines. The carboxyl and xanthate derivatives flocculated all minerals except cassiterite; the latter was flocculated by only the diethanolamine derivative. The iminodiacetic acid derivative flocculated hematite, goethite, chromite, cuprite, and pryolusite fines. Zeta potential measurements were made to help define the reaction mechanism responsible for flocculation. These measurements indicate that electrostatic attraction probably is not involved, except possibly in the case of the diethano lamine derivative. The separation of hematite from quartz by selective flocculation with chelating cross- linked starches under two pH conditions and with two dispersing agents is described. Best recoveries and grades were found when either the carboxyl or xanthate derivatives was added at the natural pH of the pulp in the absence of a dupersing agent.

Jan 1, 1983

By Robert Stefanko

The Federal Coal Mine Health and Safety Act of 1969 had far reaching effects upon many aspects of mining, ventilation being no exception. In this paper, good ventilation procedures are briefly reviewed, and attention is focused on the changes brought about by the new Act. By way of illustration the ventilation system for a typical Pittsburgh Block system is developed and the requirements of the fan determined. This is then solved by an available computer program, and the application is evaluated. Figure 1 represents a projected system for a coal property 1 by 3 miles in plan at a depth of 1000 feet with a coal thickness of 6 feet and desired daily tonnage of approximately 7200 tons on a two-shift basis. Only one half of the mine is shown (north area) with a mirror image mining arrangement to be developed concurrently for the south area. Six working units are projected, three in each area, one on pillar extraction, another developing panel entries and a third on main entry development. A two-split system is used for each working section so that the continuous miner and bolting crews each have a separate split of air, and no equipment need pass through a line brattice. The old requirement of 6000 cfm at the last open crosscut has been increased to 9000 cfm, and for the first time a minimum quantity (3000 cfm) is stipulated at the face thus requiring either line brattice or an auxiliary fan. With the respirable dust requirement limited to 3 mg/m3, the use of a blower system is precluded and exhaust systems are virtually the only choice. Maintaining the line brattice within 10 feet of the working face at all times as required by the new law has a definite effect on the mining cycle and is most difficult at best. In the highly gaseous Pittsburgh seam located in south-western Pennsylvania and northern West Virginia quantities of 20,000 cfm per split are not uncommon to maintain the methane percentage below the required l%

Jan 1, 1972

By John Hayden

The nation runs on energy. It is essential for the economic growth and national security of the United States that the nation has an adequate, sustainable, environmentally acceptable and economically viable balanced supply of energy sources, (e.g., coal, petroleum, nuclear, natural gas, solar, wind, geothermal, biomass, hydroelectric power). Therefore, the allocation of mineral raw materials to the energy-producing sector of the economy must be a top priority that requires the total demand for energy-related materials be judged in terms of domestic supply (Fig. 1).

Jan 1, 2012

By Louis A. Panek

INTRODUCTION Block caving is distinguished from other types of mining in its requirements that the mineral body to be extracted must cave after a relatively large tabular open¬ing is created underneath it, and that the caving must be predictable and controllable for both operating and safety reasons. A mineral body that caves readily may present special problems with respect to ground support in the mining access openings, where stability, rather than failure, is the desired objective. The complete ex¬traction of a caving block, which may measure 50 to 100 m on a side and 100 to 300 m in height, tends to create a large void, resulting in significant changes in the ground stress system and a migration of rock from all directions toward the void; these events begin very early in the life of the mine and lead to additional spe¬cial problems with respect to control of ground move¬ments in the mine working areas, in the rock adjacent to the caving stope, and on the subsiding surface above the mine. Thus, the mechanics of an undercut-cave operation involve a broad range of geotechnical subject matter, including the determination of the lithostatic earth stresses, the structural properties of a large jointed rock mass, the flow properties of the fragments after caving, the stability of tunnel-like openings, and the stability and displacements of the rock structure (1 to 2 km in size) that surrounds the ore body. The objectives are achieved by in-place measurement of rock properties, laboratory tests, theoretical structural analyses of the related prob¬lems, measurements of structural behavior in and above the mine, and comparison of theoretical predictions with actual performance in order to interpret and refine the predictive capability. Undercut-cave mining (Julin, et al., 1973) differs from most other methods in that the caving is an essen¬tial and inherent part of the excavation process and in¬volves the movements of millions of cubic meters of rock over distances of hundreds of meters, as compared to the gradual 2-m settling of the overburden typical of full¬caving longwall coal mining. Undercut-cave mining may involve a rock mass on the scale of a 1-km diam open¬pit mine, but mining is several times deeper than that in the open-pit mine; furthermore, a large portion of the rock mass is in a failed, rather than a stable, state. Ground-control problems are inevitable in a situa¬tion where ground movements are occurring on such a large scale, and where the rock mass is expected con¬veniently to cave at one location but to be stable at an¬other. To devise effective responses to these ground¬control problems, one needs to know first of all what is happening, not merely at the point where the symptoms are observed, but more broadly with respect to the be¬havior of the entire mine rock-mass structure over the total area of extraction, including the effects on the sur¬face as well as those underground. Monitoring structural behavior on this scale would require a sizable group of people, if they attempted to measure all the significant mining-induced changes of ground displacement and pressure, even on a 100-m grid of points. The practical approach is to conduct the mea¬surements activity by a judicious sampling, making in¬termittent, concentrated efforts in selected areas of lim¬ited extent to study problems of immediate importance; simultaneously a minimum level of surveillance is main¬tained over the total structure to delineate long-term be¬havior trends in the major structure, which provide the baseline reference data that are so essential for interpre¬tive purposes. Mine-structure behavior depends not only on the mine extraction configuration and sequence, but on the rock structural properties and how they change from one location to another in the mine. Increasing attention is being given to determinations of rock strength and de¬formation by performing mechanical properties tests in place and in the laboratory, and by drawing inferences from the mapping of geologic structure in mine openings as they are driven and from the logging of cores ob¬tained from exploration drilling that may be performed primarily for delineating ore reserves. Monitoring of mine-structure behavior and inter¬preting it in terms of the growing excavations and the structural properties of the rocks have significant im¬pacts on designing the major undercut-cave operations of undercutting and drawing the ore, supporting the ac¬cess openings, and controlling surface subsidence. The purpose of this chapter is to call attention to the com¬mon ground-control problems encountered in undercut¬cave mining, to relate them to the mining process, and to explain the geomechanical approaches to analyzing these problems with emphasis on methods that are most readily available to the mine staff. UNDERCUTTING, CAVING, AND DRAWING A distinguishing characteristic of an undercut-caving method of extraction is the objective that the rock mass fails of its own weight in a predictable and controllable manner, after it is undercut by excavating a tabular¬shaped void, horizontal or inclined. Induced or forced caving refers to procedures that may be resorted to when the ore will not self-cave over the desired span. Block caving, panel caving, and mass caving are terms used to denote the particular sequence of undercutting and ex¬tracting the total area of the ore body on a single min¬ing level. The discussion herein is not specialized to any of these variations; the word block as used does not imply anything as to sequence. CREATING THE UNDERCUT A common undercutting method is to drive a series of drifts and blast the intervening pillars. Theoretical structural analysis and practical experience show that ground-support problems in the undercutting drifts and in underlying access openings as well (the same princi¬ple applies even if undercutting is done by belling out drawpoints from the slusher drifts) are minimized by retreat-mining across the undercut slot according to a sequence such that the growing undercut area retains a

Jan 1, 1982

By W. G. Cornwall

The mining field, inclusive of the treatment plant is located in the foothills, five miles inland from the northern coast of Viti Levu, the largest and most important island of the Fiji Group. Gold and silver occur as tellurides, associated with the sulphides, and as minor occurrences of electrum.

Jan 1, 1975

By A. T. Yu

There are compelling reasons for us to look to our Country's Western coal. Despite its inherent low BTU content, Western coal's low sulphur content provides a near-ideal answer to satisfy our in- dependent goals of clean air and self-sufficiency in energy. Vast reserves, thick seams and amenability to low-cost strip mining serve as a powerful economic basis for its viability as a primary and dependable source of energy for the coming decades. A major consideration, the solution of which may not be quite obvious, is transportation cost. These abundant deposits are remote from the utilities of the heavily populated eastern regions of the United States (Figure 1). A Western coal mine in Montana is likely 1500 miles or more from an eastern power plant. The comparable distance to an eastern coal mine may be only 200 miles. Thus, the question is: How can the haulage cost of our Western coal be substantially reduced to an acceptable level? If resolved, western reserves of coal will be one of the key solutions to satisfying our Nation's energy needs.

Jan 1, 1975

By A. F. Peterson

There is no single mining problem at Benson that does not exist at some other mine. There are four, however, that require special attention primarily because they occur together and have an influence on each other. These are the nature of the mineral occurrence, the shape of the ore body, the operating schedule, and the climate. It is the purpose of this paper to describe mining practices in relation to these four factors. Iron ore was first noticed in the Star Lake area early in the nineteenth century. Prior to Jones and Laughlin leasing the facilities built by the Defence Plant Corporation, several companies tried to mine the ore body but gave it up as uneconomical. While there is a little high grade (40%) magnetite, most of the ore contains 20 to 25% iron and not enough was known prior to World War II to design a profitable operation. By 1943, and certainly in the years that followed, technological developments in ore dressing and mining not only put the magnetite into the category of a commercial ore, but made possible the concentration of the non-magnetic iron mineral, martite. This last development nearly doubled the ore reserve. Jones and Laughlin bought the DPC holdings in 1946 and has since expanded the plant to its present capacity of 4,400 gross tons of concentrates daily or 1,600,000 gross tons per year. Magnetite makes up 62% of this production at the present time, but it will be necessary before long to bring martite production up to about 45% of the total because of the ratio of the two ores in the reserves. To keep the plant supplied, 14,000 to 15,000 tons must be mined and crushed daily, with a ratio of concentration that varies from 2.8 to 3.4. The ore body is 12,000 feet long and varies in width from 600 to 1,500 feet. The waste rock is, for the most part, a granite gneiss, and the overburden, of which little is left, is a glacial drift sand. For the entire reserve, there is a half ton of rock for every ton of concentrate, but the stripping ratio is more than one to one at present because of the existence of more rock in the upper mining levels in relation to the ore. The dirt stripping or development work that cannot be handled by company facilities is contracted to an outside firm. The need for this diminishes every year and will soon disappear. The deposit looks like a "J" in plan, with the long leg running approximately north and south and the short leg to the west. The primary crushing plant, consisting of a 54" gyratory followed by two 18" gyratories and a 1,500 foot conveyor belt to the fine crushers, is located on the third level where the long and short leg of the mine meet. The widest part of the pit lies just the north of the crusher. The mine is operated on a lease that expires in 199l0 There are two fee owners, the Benson Iron Company, which owns slightly overhlf of the reserves, and the Newton Falls Paper Company, which owns the balance. There is no appreciable difference in the mining on the two fees, so the ore is removed in strict proportion to calculated reserves during each year. Basic mining equipment consists of eight 45 yard electric shovels, a fleet of twenty-five 22 ton end dump trucks, eleven churn drills for nine inch blast holes, and two small percussion drills for four to five inch holes, There are the normal auxiliary items, such as dozers, graders, wagon drills, and two drop-ball cranes. Power is purchased and, where practical, is used at 4100 volts. Pit drainage pumps can handle a maximum of 11,500 GPM from the several sumps, but water is a problem only during the spring or when a sudden thaw follows a heavy snowfall.

Jan 1, 1958

By Robert Stefanko

The results of a recent study on the influence of continuous and conventional mining techniques on the size consist and wash- ability characteristics of coal are presented. Eight samples, four each from continuous and conventional mining sections were collected. Each sample was screened in seven size fractions, and each size fraction was totally fractionated at five gravities. The data thus collected was statistically examined for the influence significance of mining techniques, size, and gravity on the quality of the mined product. The paper presents the sample collection method, data gathering and analysis procedures, and major conclusions. The study revealed that there are pronounced differences in the products from the two mining systems and that conventional mining yielded a better product in terms of size-consist, and yield, ash, and sulfur in both the raw and washed products. The results of the study are significant in regard to consideration of resource utilization and conservation, and environmental impacts.

Jan 1, 1974

By G. Barbery

In Mineral Processing, the objective of most processes is the separation of mixtures of minerals, which are originally associated in composite particles. Feed preparation processes grinding for instance, which take place before beneficiation or separation processes do not usually break particles at the boundary between mineral phases. They produce composite ("middlings") as well as liberated particle. It is therefore necessary, in a particulate system, to determine the proportion of particles which are liberated as well as, ideally, the size distribution of minerals which remain associated in composite particles. Up to now, there has been a lack of experimental techniques to characterize completely composite particulate systems. Heavy liquid separation which is commonly used to obtain information of this type can only be applied to simple binary cases for which one mineral has a low density (lower than e.g 2.8 ). The technique which is proposed in this paper involves the measurement of parameters on polished sections of particles mounted in a matrix, and the use of mathematical transformations to reconstruct in three-dimensions the information obtained from these measurements .

Jan 1, 1977

By T. M. Yegulalp

A short review of the current practice and recent developments is followed by a description of a newly developed approach for the solution of the optimum ultimate pit limit problem. The new approach utilizes the network modeling of the problem for solution by maximum flow algorithm. The latest developments in the implementation of maximum flow algorithm present significant time and memory savings as compared to initial development due to Ford and Fulkerson. Results of a series of computational tests are presented to demonstrate how this approach performs as compared to the well-known Lerchs Grossman algorithm. It is also shown that the solution by the new method will automatically include several optimal solutions based on predetermined number of benches to be included in the analysis.

Jan 1, 1993

By Bruce Kennedy, Charles Bruce

MINERAL EXPLORATION 'The Function of Exploration Mineral exploration aims at locating the presence of economic deposits and establishing their nature, shape, and grade. As all ore bodies are finite, exploration is essentially the lifeblood of the mining industry. It is divided into two phases, reconnaissance and target investigation. It involves geological mapping, geophysical prospecting (aerial and ground or both), geochemical surveys, prospect drilling, and/or exploratory under-ground workings. Successful exploration is followed by development drilling, mine development, and eventually operation. In underground mining, the term "ore" is applied rather loosely to metalliferous rock that can be profit- ably mined, but nonmetallic industrial minerals and energy related materials constitute a large and growing portion of the tonnage extracted by underground methods each year. It is appropriate, therefore, to consider exploration as the search for any useful substance occurring in the earth or in the oceans that is of sufficient value as to volume, grade, chemical and physical com- position, and location as to make extraction by mining commercially profitable for the investment required. The Selection Process The search for ore includes hundreds of mineral commodities. The more successful exploration organizations tend to restrict the search to the mineral commodities for which they have strong exploration expertise and which have a high probability of being concentrated in areas open to exploration and development in sufficient volume, grade, and proximity to the surface to warrant the large expenditures of risk capital in finding an ore body. Special expertise is needed to engage in mineral exploration and development for the extended periods required for success. Individual prospectors continue to discover mineral occurrences, but it generally takes an organization with strong financial resources to carry the exploration process forward to the point of developing "ore." Still greater corporate resources in the form of management, engineering, and sales capability are needed to develop an ore body into an operating mine. In the past, companies other than those engaged in mining rarely conducted exploration, since they lacked the technical skills and know-how to bring a mine to fruition. A notable trend in recent years has been the success of other resource-oriented firms, such as petroleum companies, that have not only acquired the necessary skills to engage in exploration for hard minerals, but are doing so on a far more intensive scale than known in the industry heretofore. The desire to diversify from increasingly regulated oil and gas, the potential for the discovery of a bonanza, and the large scale of mining projects for these capital-intensive firms are the attractions. US government and certain international organizations, such as the United Nations, have fielded sizable exploration programs in the past decade on behalf of Third World countries wherein many of the world's higher grade deposits and scarce mineral resources are located. The level of overall mineral exploration in the industry is, regrettably, closely geared to the business cycle. Accelerated search during the periods of strong demand, shortages, and high prices, together with the long lead times necessary to develop mineral finds, often creates surges in supply which invariably are followed by a collapse in prices. The trend is, therefore, to exploration funding by larger better-endowed firms having the staying power to weather the cyclical nature of mining. Tax incentives, tariff policies, and other incentives have a decided impact on the level and nature of exploration. Surface mining regulations and environmental forces have fostered a renewed interest in under- ground development despite the lower average costs of surface mining. Spiraling inflation has caused mining costs to outpace prices for many mineral substances. Organizations increasingly are directing their search away from high- grade but limited tonnage occurrences toward low-grade disseminated bulk tonnages amenable to mining on a vast scale. Mining continues, therefore, to grow even more capital-intensive with half-billion-dollar mine-mill- smelter complexes now commonplace, compared with the hundred-million-dollar projects of a decade ago. Reconnaissance Exploration Having elected to search for specific mineral commodities, the exploration company narrows its focus to a reconnaissance of those regions offering the best potential. A working hypothesis which is constantly up- dated concerning the geologic controls for ore occurrence guides the search. The possibilities for discovery are best in areas of existing mines and known ore bodies, where the probabilities are high for additional ore occurrences. In such areas, published data on the trends and geologic controls of known mineral occurrences aid the search. Even in some remote territories, a variety of geologic data is available to the explorationist. The major sources of basic geologic data are the libraries of the US Geological Survey (USGS), the state geological surveys, the American Institute of Mining, Metallurgical, and Petroleum Engineers (AIME), the US Bureau of Mines, and various institutions such as Colorado School of Mines. Overseas, virtually all of the countries have their own geologic survey groups which are associated directly, or indirectly, with their respective ministries of mines. The objective of reconnaissance exploration is to narrow the search by pinpointing target areas having interesting mineralization. These favorable areas are then investigated in detail to delineate potential ore bodies.

Jan 1, 1982

By D. Shink

A small scale continuous flotation cell was designed and constructed at Noranda Technology Centre to develop a mobile testing flotation circuit located next to the production circuit. This mobile small scale flotation pilot plant can easily and economically be set up at any circuit in a mill and used to evaluate and predict plant performance against a given flotation condition. The main feature of the cell, beside the provisions of automatic pulp level and feed rate control, is to provide a reduced surface to volume ratio approaching to that of an industrial machine. This paper describes the basic design and the results of various testwork carried out to date including aeration, conditioning, reagents, recirculation, flotation gas, etc. are presented in comparison with the plant production results.

Jan 1, 1992

By Leonard B. Rothfeld

For many years, pulverized coal (PC) boilers in utility power plants have been the dominant market for domestic coal. Today, two new coal utilization technologies challenge the PC boiler's dominance. Atmospheric fluidized bed combustion (AFBC) and "coal gasification/combined cycle" (GCC) stand on the verge of commercial demonstration in the utility environment at a scale of 100 MW. Developed over the past decade, these technologies respond to the demands for cleaner ways to burn coal and for more flexibility in fuel supply. In the near term, these are the "clean coal" technologies most likely to have a significant impact, because they are ready for commercial application. As for environmental acceptability, consider that just a few years ago one of the environmental slogans was "no coal in California." Indeed, the only large quantities of coal above ground in California at that time were in transit on the way to Asia. Today, thanks to new technology, we can point to two operational coal-burning plants in California and one in the works: * Cool Water GCC demonstration plant (100 MW) * California Portland Cement AFBC commercial cogeneration, near Riverside (190 000 lb/hr steam) * Energy Factors AFBC commercial cogeneration at Stockton, to be operational 1988 (44 MW)

Jan 1, 1987

By Muhammad I. Kabir

A new minitest of in situ uranium leaching processes at reservoir conditions is proposed. The test which consists of a single observation/ production well and two observation wells is designed to permit the evaluation of both restoration and leaching parameters. It is shown that by using a straight forward history matching procedure, sometimes called a type curve analysis, both the rate of leaching and the ultimate uranium recovery can be evaluated based on the results of the test. Type curves are presented for the case in which the reaction rate is kinetically controlled and there are no other minerals competing for oxidant. Other situations can be approached using the same techniques as those presented here.

Jan 1, 1981