Search Documents

By W. J. D. Stone

In 1960, Magnetics International Ltd. undertook the development of the Jones High Intensity Wet Magnetic Separator in the Americas. Magnetics International had a number of possible applications in its own projects plus the intention of developing the equipment for sale to others. It was soon recognized that no matter how innovative a piece of mineral separation equipment may be, it takes many years and much finance before it is finally accepted for large scale use. For this reason, many good ideas die in their infancy. One of the chief reasons for such a time lag between conception and large scale implementation is the usual lack of finance to construct and put into operation a large demonstration unit. Even with a large unit for demonstration, the first major user usually requires a guarantee that is not normal in accepted separation equipment. Such problems are also normally accompanied by major design changes from the first conception.

Jan 1, 1971

By O. M. S. Rodrigues

The kaolinite presence in bauxite ores increases caustic soda consumption during the digestion step in the Bayer process. Depending on the kaolinite content, the utilization of the ore in the Bayer process may be unfeasible. This investigation addressed the variables involved in kaolinite flotation through microflotation experiments in a Hallimond tube and zeta potential determinations. The tests were performed with a pure sample of kaolinite (96%). Five collectors were tested: Duomeen T (DT), cetyl pyridinium chloride (CPC), cetyltrimethylammonium bromide (CTAB), dodecylamine (DDA) and Flotigam EDA (EDA). Four of them performed well as collectors, at a concentration of 1x10-4 mol/L: CPC, CTAB, DDA and EDA. The kaolinite isoelectric point (IEP) was determined at pH = 4.6. The IEP was shifted towards higher pH values in the collectors? presence, indicating specific adsorption onto the mineral surface.

Jan 1, 2011

By Shinya Ono, Tsuyoshi Katoh, Yuusaku Tominaga

In order to monitor/control airflow rate distribution in a complicated ventilation network installed many regulators, an integrated system composed of expert system, exerting programs for simulation to get macroscopic characteristics and drawing diagram, monitoring system and so on is introduced in this study. This system is made up of airflow velocity sensors and computers linked to an local area network. The main results of this study are as follows; 1) Combinations of two branches to monitor aerodynamic resistance change in a branch p in a network can be selected by comparing factor's value in a branch relation table. 2) When the combination of sensor branches for a branch p does not exist in the network at present condition, the system changes aero- dynamic resistances of appropriate branch q placed a regulator by referring branch relation table. And then the system asks other computer to get macroscopic characteristics under altered value of aerodynamic resistance of the branch q. 3) Dot pattern diagram shows airflow rate relation between an active branch and a passive branch. Three relations such as a) a straight line, b) a monotonous curve and c) extremums are displayed in different patterns for all the sets between an active branch and a passive branch at a time. 4) The ranges of airflow rate in coal faces by changing aerodynamic resistance of any one branch placed a regulator are shown in the Pareto diagram using values in the branch relation table. 5) Ventilation transfer diagram with two parameter, one shows airflow rate in a coal face and the other shows energy provided by main fans to overcome aerodynamic resistance in a net- work, is utilized to decide countermeasures for decreasing energy consumption in the network on increasing of airflow rate in the specified branch.

Jan 1, 1995

By David A. Roberts, Edward J. Cording, James W. Mahar, Robert A. Robinson, Noppadol Phienweja, Harvey W. Parker

Horizontal inclinometer and deflectometer casings were used to measure deformations up to 15.2 m (50 ft) ahead of and adjacent to the heading in highly fractured and sheared shales at the Stillwater Tunnel. The measurements were compared with borehole extensometer and tape extensometer deformations to evaluate ground movements in advance of, adjacent to, and behind an advancing tunnel heading. Ground deformations of up to 127 mm (5 in.) occurred during passage of the innovative "walking blade-gripper" TBM. Deformations were compared with curvometer/distometer and vibrating wire strain gage data from steel ribs to assess rock-support interaction.

Jan 1, 1985

By Rollin A. Slater

The bulk materials handling industry has served silently for years as the skeleton structure and often the central system of nerves and nourishment for the body of basic production industries. During the past two decades, this body has undergone substantial growth and mutation to meet the surging demands of our national economy for more and better products. The steel industry has been prominent in this phenomena and plants of the sixties are as unlike the second war vintage as our current crop of basketball players differ from their fathers. Steel has kept pace with spiralling demand by innovation which has resulted in new processes and improved designs which generally yield greater production from fewer units. The supporting industry of materials handling has likewise improved its techniques and currently has a new stronger generation of equipment to perform its necessary supporting function. It has been my fortunate experience to have been instrumental in the creative stages of several new steel mills which are currently in conceptual design or actual construction. Drawing upon exerpts from this experience, this paper will describe a basic approach to the selection and application of modern bulk materials handling systems to an entirely new steel plant. Specific details of past work are not available for publication, therefore, the plant described herein is a composite of ideas and will be the new plant of the Hypothetical Steel Corporation which will be located on the lower shores of the Great Lakes.

Jan 1, 1967

By R. W. Kobler

The pelletizing process for low grade iron ores has undergone continual changes since its inception over twenty years ago. These changes have necessitated filtration equipment changes in order to produce a product suitable for balling. With modern techniques it is now possible to produce pellets of 68% Fe from ores containing as low as 26% Fe. Low grade ores require fine grinding to liberate impurities This shift to finer grinds over the years has necessitated major changes in the filtration steps. Techniques are now available for producing suitable product from ores with Blaines as high as 3600 cm2/gram. This has been made possible by the development of high performance filters. Recent developments have reduced maintenance costs and produced higher production reliability. The paper discusses iron concentrate filtration from its beginning to present day design. It will be shown that the dewatering step prior to balling has gone through four generations of filters. Particular emphasis is placed upon hydraulic studies which have allowed today's optimum designs.

Jan 1, 1978

By Frank A. Jerabek

Problems of mine backfilling and fill material deposited underground, the characteristics and relationship between the deposited fill material and overlying ground, and the practical applications and limitations of hydraulic backfilling as ground support are discussed. A great variety of materials ranging from coal washery refuse to concentrator tailings is used as hydraulic fill. Some materials will solidify and cement; others will resemble quicksand, Hydraulic fill as ground support is more efficient in inclined mine openings than in horizontal mine openings, where it cannot be placed tightly to the back. This and other deficiencies of hydraulic backfilling led to the development of pneumatic stowing. Research work in hydraulic backfilling at the Pennsylvania State University is also discussed. This research work includes the investigation of segregation in the discharged fill slurry, the quantity of solids escaping in the drain liquid, the relationship of escaping solids to slurry concentration and discharge rate, and the compressibility of fine fill material.

Jan 1, 1965

By John H. Clark

This paper outlines new technological improvements in underground trackless equipment for the metal mining industry with emphasis on maintenance related developments for Load Haul Dump machines. Also new developments on other types of equipment are covered including drills, road headers and electric LHD's.

Jan 1, 1983

By T. H. Koenning

Spontaneous combustion in western U.S. coal mines has been recognized as a serious problem which requires unique solutions. Methods have been developed for longwall mining which rely on the existence of an oxygen-deficient atmosphere in the gob for control of the spontaneous combustion hazard rather than the use of bleeder systems. Monitoring of the gob atmosphere is required to protect against the possibility of an explosion and to detect spontaneous heatings. Data from an example mine employing such a system is included to illustrate normal gob gas trends and is compared to abnormal trends which resulted from and were indicative of a fire. Under normal circumstances the oxygen (O2) and carbon monoxide (CO) concentrations decline rapidly as the longwall face retreats. Samples taken from a leaking seal in the example mine prior to a spontaneous heating showed virtually no oxygen depletion, contained erratic CO concentrations, and indicated the existence of hydrogen, a fire indicator. The appearance of an abnormal trend in the gob atmosphere can be used as an early warning of spontaneous heatings.

Jan 1, 1992

By Milton E. Jennings

On May 11, 1977, the SAMARCO 20-inch, 396-kilometer (246-mile) Pipeline was placed in service. This system represents the latest thinking in slurry pipeline design and is one of the main contributors to the viability of the SAMARCO Project. This paper presents the background, description and latest information on the system's operation. Special attention is given to the handling limitations of the slurry and to the unique hardware requirements.

Jan 1, 1978

By R. J. Sweigard

Three case studies were undertaken to investigate the role of land use potential evaluation in reclamation planning and to determine the impact of regional differences on the evaluation process. The three surface mines studied were representative of operations in the Appalachian, Interior, and Northern Great Plains provinces. The scope of the investigations included a survey of regional characteristics, a detailed investigation of the mining operations and site conditions, and an assessment of local land use planning activities in the area of the mine. Special attention was given to key factors that presently determine the use of reclaimed land. Also, for each case study, the postmining land use potential was evaluated using site planning principles. Specifically, the environmental, economic, and social impacts of several potential postmining land use plans were considered.

Jan 1, 1983

By David E. Nicholas

Design of underground openings is becoming more critical as the mine deposits become lower in grade, initial investments increase, ore depth increases, additional safety regulations come into law, and increased ore recovery is required for conservation of minerals. Stability of these openings is dependent on the strength of the rock mass and the pre-mine stress field. The rock mass is composed of solid blocks of rock (rock sub- stance) and structural features (faults, joints, bedding, etc.). Methods of testing the rock mass strength are improving and be- coming more common, however it is difficult to justify the high cost of large scale testing for an initial mine design. An alternative to testing the rock mass is to measure the rock substance and the structural features separately, and then combine them to estimate the rock mass strength. The rock mass strength will vary depending on the orientation of the opening with respect to the structural features. The other factor affecting the stability of underground open- ings is the pre-mine stress field. Methods are available to measure "directly" the pre-mine stress in competent and relatively massive rock. These methods are costly to employ, therefore, they may not be justified in an initial study. The pre-mine stress field can be estimated based on the structural relationships formed from past tectonic events.

Jan 1, 1976

By William C. Larson

The Bureau of Mines, as a result of its contract research program, is developing a retractable core bit for the wireline drilling system (Retractable Sit System, No, H0272004). The prime contractor, Longyear Company, Minneapolis, Minnesota, and the subcontractor, Doerfer Division, Cedar Falls, Iowa, have designed, fabricated, and are currently field testing the in-hole retractable bit system. he objective of the program is to develop a minerals exploration core drilling system that allows retraction of a worn out bit and insertion of a new core bit, without pulling the drill rods out of the hole. To date, the results of the project are encouraging, and the retractable bit contract is currently in the last phase of a four-phase program, which is on schedule and under budget.

Jan 1, 1980

By R. Larry Grayson

A survey of 1250 surface and underground coal mines across the United States was made according to a stratified sampling technique based on national coal districts. A total of 171 responses (13.7% response rate) have been returned and summarized, giving a picture of computer usage in the coal industry. Overall, 63.5% of the respondents use computers, but the percent varied from 100% for large mines to only 44.1% for small mines. As expected, a proliferation of microcomputers has pervaded the industry. Importantly, in spite of the high usage of computers in the industry, sophisticated engineering applications have not yet burgeoned.

Jan 1, 1989

By C. H. Perbix

[On Pier D in the Port of Long Beach, California, the Port of Long Beach has built a new bulk cement distribution terminal. The facility is operated by Pacific Coast Cement Corporation, who designed the complex and leased it from the Port of Long Beach on a 40-year lease. At one bulk cement is unloaded from vessels carrying from 12,000 to 30,000 t. The unloading is performed with pig speed mechanical unloading equipment and delivered into a concrete silo complex with, a capacity of 50,000 t. From the silos, bulls cement is loaded into trucks for delivery. The facility was completed in September 1981.]

Jan 1, 1983

By J. Bartrum, A. Bowler, G. Butcher

The purpose of this paper is to outline the design, specification, and operation of the 8.5-m- diam (28-ft-diam) SAG mill commissioned at Kidston Gold Mines during January 1985. Amenability of Kidston ore to SAG milling, coupled with substantial cost advantages, led to the specification of this mill, equipped with variable speed drive to overcome the large variation in ore hardness. Operation of the mill is effected via a number of automatic control loops. Problems experienced with automatic control plus other electrical and mechanical failures have led to design changes and the formulation of future operating strategies.

Jan 1, 1987

By L. K. Holder

"The Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), commonly known as Superfund, mandates evaluation of remediation alternative using nine criteria: (1) overall protection of human health and the environment, (2) compliance with ARARs (applicable or relevant and appropriate standards), (3) long-term effectiveness and permanence, (4) reduction of toxicity, mobility or volume, (5) short-term effectiveness, (6) implementability, (7) cost, (8) state acceptance, and (9) community acceptance. Many states have adopted these or similar criteria for remedy selection under state laws. Although not explicitly addressed in the CERCLA criteria, consideration of sustainability can be incorporated into these criteria. This paper explores how sustainability can be evaluated for remedy selection using the CERCLA criteria. INTRODUCTION Sustainability considerations can be incorporated into all phases of site remediation: • Site investigation (remedial investigation). • Remedy selection. • Remedial design. • Remediation construction. • Operations, maintenance, and monitoring. This paper focuses on remedy selection. Many have looked at remedy selection using sustainability criteria. However, CERCLA and corresponding State programs require remedy selection using mandatory criteria. This paper shows how sustainability can be explicitly considered using the mandatory criteria. REVIEW OF CERCLA CRITERIA First, we review the definitions of the CERCLA criteria. We then explore how sustainability criteria can be fit into the CERCLA criteria. Overall Protection of Human Health and the Environment This criterion addresses the degree to which each alternative is protective of human health and the environment, considering both long-term and short-term risks. Overall protectiveness is a ""threshold"" criterion, in that alternatives that do not achieve adequate protection of human health or the environment are eliminated from further consideration. Evaluation of this criterion is derived from the evaluation of the other criteria (e.g., long-term effectiveness and permanence, and short-term effectiveness). It is not an independent criterion, but more a summary of the overall evaluation."

Jan 1, 2015

By Jodie Robertson, Isabel Barton, Cristian Caro

Prior to mining, all rocks contained in a mineral deposit must be placed in one of several categories known as ore types. Each ore type describes a different way that the rock will behave in processing. The ore type determines which process stream a particular mined unit will be sent to, sets expectations for process engineers and metallurgists, and forms the basis for recovery predictions and production estimates. At first, ore types are assigned mainly by geologists based on visible geological criteria (dominant ore mineralogy, estimated grade, rock type, alteration type). As metallurgical tests are carried out and process data accumulate, the resulting criteria may be factored into the ore typing process, typically as assays and recoverable metal using the relevant process(es). Other variables may also be incorporated into ore typing at operations if they are particularly important, such as grindability, preg-robbing, gangue reagent consumption, and the presence of especially deleterious minerals such as talc or smectite. The mine operation department may also redefine ore types and/or process destinations based on economic criteria. A “best” ore type is designated that (in theory) best describes how the rock will behave in processing. Codes representing this ore type are entered into the drill-hole database, then interpreted on cross sections and level plans, and finally added to the block model. Ore types are iteratively reexamined and adjusted over the life of a project. Major difficulties in effective ore typing are (1) lack of communication between geologists and metallurgists, (2) the imprecision inherent in imposing clean categories on messy natural systems without discrete divisions, (3) the need for ore types to provide useful information for a wide range of processes, (4) difficulties in scaling up laboratory test results to mine production, and (5) conflict among geological, metallurgical, and economic criteria for ore typing.

Jul 1, 2024

Mill #4 processes mildly refractory ore from Carlin Trend deposits. Diagnostic analysis of plant operating data was used to generate a mathematical model containing the important parameters influencing gold recovery. The model was used to direct modifications to plant operating practice. The cyanide-dosing strategy was changed to reduce gold losses from preg-robbing and to cut reagent consumption. A finer grind was achieved without capital investment. The density in the carbon-in-leach circuit was lowered, and tighter control was exercised over the plant throughput. These changes resulted in a recovery increase of at least 2%, worth $111,000/month at $300/oz ($9.64/g) gold, and concomitant reagent cost savings of $55,000/ month.

Jan 1, 2000

By Alvaro Lucio

The continuous increase of the fuel oil price compelled CV3D to look for an alternative fuel. Charcoal was selected as the alternative energy source. This paper justifies its selection, describes charcoal properties, the methods for using charcoal in the pelletizing and shows the results of the in-plant tests.

Jan 1, 1982