Search Documents

By R. V. Ramani

Control is a vital management function by which operations are brought into compliance with predetermined standards to achieve the goals of an enterprise. Events that are characterized by a low degree of expectation, avoidability, and intent necessarily have a low degree of control. Such events are difficult not only to predict but to control as well. Fortunately, very few industrial situations fall into that category of events. It is an axiom of control technology that in order to control, one must first measure; further to measure, one must know the characteristics of the subject (or environment) upon which the measurement must be made. Finally, if measurements are to be made reliably, the influences that affect the measurement must be known and, if possible, understood. The complete control cycle therefore consists of the following: (1) defining the objective, (2) planning to achieve the objective, (3) putting the plan into practice with appropriate instructions, (4) measuring variables or parameters of interest, (5) transmitting and transforming the measurements to analyze the system's status and to predict the future outcome, (6) comparing these with the defined objective, and (7) determining and taking corrective actions to bring the actual results closer to the objective. The management principle underlying the control cycle is the principle of management by exception. The application of the principle and the frequency with which corrective actions are taken vary according to the purposes of the review and control. For example, the control of a machine operation (e.g., truck on a haul road) may require adjustments and therefore data, analysis, and decisions, in intervals of seconds whereas the review for ore-grade control may take several hours. Reviews, on the other hand, for cost control may be done in intervals of weeks or months. In any case, three specific purposes of the control cycle are: (1) to correct the operation so that it follows the accepted plan closely, (2) to evaluate the operation and predict future outcomes in light of changes in the environment or of more experience, and (3) to review the objectives and modify these to be reasonable and realistic.

Jan 1, 1979

By Fun-Den Wang

In underground coal mines, three types of roof failure (2)*, tensile, local, and shear, occur in the development entries and in room-and-pillar extraction areas. Most of the tensile failures in the roof at the center of the mine opening as well as those local failures due to fracture or jointing can be controlled by roof bolts, trusses, and timbering. However, control of the shear failure at the sides of the roof (or the cutter-roof caving) has not been successful with ordinary roof control methods. The only effective method, when there is an indication of cutter-roof caving, is to use cribs, which are costly and make transportation, ventilation, and production difficult. Frequently, the operator allows the cutter roof to cave and then cleans it up rather than trying to stop it. This shear type of roof failure is often associated with large areas which may progressively involve several hundred feet of roof caving at one occurrence. At times, this shear failure occurs suddenly with little or no warning. This can result in buried equipment and great danger to the safety of personnel. This shear failure may be due to one or more of the following: high stress concentrations at the corner of the roof from (1) high horizontal to vertical load ratio, (2) orthotropic elastic properties of rock and coal, (3) greater stiffness of the immediate roof layer than of the secondary roof layer, (4) viscoelastic behavior of rock and coal, and (5) geometry and material properties of the geologic setting. Removing or reducing the high stress concentration should improve the roof stability. The structural analyses of models of two typical

Jan 1, 1972

By P. James

Blue Planet Strategies (BPS) focuses on improved resource utilization and targets converting wastes into resources. New BPS capability (DEMET) wrings extra value from mining and processing wastes by enabling new production from waste and residual sources. This powerful platform technology provides considerable processing flexibility and enables various new economical treatment options to extract key metals from low level and process byproduct stream sources normally left as waste by traditional processing methods.[1]

Feb 23, 2014

By Benjamin C. B. Hsieh

Many processes in the hydrometallurgical and chemical industries require the separation of dissolved material from suspended solids. Counter current decantation (CCD) with thickeners is one of the methods generally used. The process engineer needs a quick and accurate CCD calculation method. Several theoretical 1-12 CCD calculation methods are available in the literature . The simultaneous 1, 2 equation method for a complex circuit as used would take too long to solve the problems. Approximate equation method1 is not accurate and is for simple cases only. A shortcut method developed by Counselman3 contains no mathematical equation, and thus is not suitable for computer programming. Based on Counselman's method, Woody4 derived two simple equations in terms of percent soluble loss for two typical examples. Scandrett5 included a term for mixing in his formulas. This mixing efficiency was defined by Murphree6. Another method which depends on making volume calculations instead of using weights is presented by Mastin8 and Cahalan9. None of these methods is related to dissolution and pre¬cipitation reactions. Chen 10,11 demonstrated his methods for counter current leaching. His results are calculated from the general solution of a derived linear difference equation for constant underflow, and from the solution of a derived non-linear Ricatti difference equation for variable underflow. This paper concerns derivation of a general equation for CCD washing with provisions for adding and withdrawing the streams, and for leaching (dissolution) or precipitation reactions. These equations take several forms depending on the input information available. A set of simplified equations for continuous counter current washing and leaching is derived for determining:

Jan 1, 1972

By N. B. Aughenbaugh

A study was made to determine those petrographic parameters that are correlative with carbonate-aggregate quality as indicated by the Los Angeles abrasion and absorption tests. Samples collected at 28 sites in northern and eastern Indiana were analyzed petrographically, chiefly for void content, grain size, grain-size variation, grain shape, and grain interlock. Most of the sampled sites are in the belt of Silurian rocks of east-central and north- western Indiana. Though a few sites lie outside this belt, most of these have only a thin Devonian section above the Silurian. Three sites are non-Silurian and are included for comparison. Most of the samples studied are from Middle and Upper Silurian units. Both biohermal and nonbiohermal facies are included. The biohermal rocks are typically dense but vugular, finely crystalline granular dolomite. Nonbiohermal facies are porous, medium to coarsely crystalline, granular dolomite with dolomite rhombs The Los Angeles abrasion losses ranged from 20 to 46 per cent, the rocks in the eastern part of the state showing the higher values. Absorption tests indicate the same general quality trend. Comparison of petrographic studies with Los Angeles abrasion- and absorption-test results indicate the following correlations. (1) As per, cent of voids increases, quality decreases. (2) As average grain size increases, quality decreases. (3) Variations from mean grain size appear to have no effect on the quality. (4) As angularity and roughness of the grains increase, quality increases. (5) As grain-to-grain interlock increases, quality increases. Variations in the calcium-magnesium ratio have no apparent effect on aggregate quality, except as they affect the texture.

Jan 1, 1966

By W. V. Swarzenski

In its, effort to combat waterlogging and coil salinity, the later and Soils Investigation Division of WAPDA (West Pakistan's Water and Power Development Authority) has carried out an extensive program of test drilling and water sampling, since 1954. Data collected during the past ten years have permitted the delineation of fresh and saline ground-water-zones in the Punjab Plain. Fresh ground water containing generally, less than 500 ppm (parts per million) of total dissolved solids is found in wide belts paralleling the major rivers and in other areas of fresh-water recharge. Locally, fresh ground water extends to depths of 1,500 feet and more. Saline ground water occurs downgradient from sources of recharge, particularly in the lower central parts of the interfluvial areas and, presumably, underlies most of the Punjab Plain. The ground waters of the Punjab are characterized by their evolution from calcium, magnesium bicarbonate waters, near sources of recharge, to waters containing a dominant proportion of sodium. The highly mineralized waters of the Punjab are generally of the sodium chloride type, whereas in Dera Ismail Khan District sodium sulfate waters predominate. The pattern of distribution of saline ground-water zones and the observed gradual increase in mineral content, downgradient from sources of recharge, can be explained best by a hypothesis stressing the processes of evaporation from the water table and solution of minerals within the alluvial aquifer.

Jan 1, 1967

By Norman K. Olson

Hard-rock phosphate was formerly the chief source of all phosphate in Florida. Its mining began as early as 1883 or 1884, reached a peak level in 1907 and ceased in 1966. Production began and ended in the Dunnellon area (Marion County). Nearly all the hard-rock was exported because its P205 value per unit weight is generally more concentrated than that of other phosphate rock. Maximum production, achieved in 1907, was greater than 600,000 tons; the total value for that year was more than $4,000,000. The Florida hard-rock phosphate, considered to be of middle Miocene to early Pliocene age, has an intermittent narrow, linear northwest-southeast trend. The Ocala uplift controls the phosphate distribution for more than 200 miles. Other known, isolated hard-rock areas appear to be related to minor folds on the Ocala uplift. The hard-rock phosphate deposits are a heterogeneous mass of sedimentary fluorapatite, chert and quartz with textures ranging in size from clay to boulder, and in thickness from 0 to 40 feet. Phosphate compounds, principally fertilizers, have been in oversupply since before 1968, but by the middle 1970's some experts forecast a supply-demand balance. A brighter future for exploitation of Florida hard-rock phosphate depends upon one or more of these factors: 1) depletion of present premium grades (74 percent BPL and above) of land-pebble; 2) cheaper electric power from nuclear generators for profitable electric furnace operation; 3) supply and price of sulfur; 4) manageable rail-water transportation costs; 5) development of less costly mining and separation methods; and 6) minimum competition from high-grade foreign phosphate.

Jan 1, 1972

By Charles L. Allie

In June, 1980, Reserve Mining Company completed a 370 million dollar construction project which included process modifications required to reduce the silica content from nine to five percent by weight and increase the iron con- tent of Reserve's pellets from 62.5 to 65.8 percent by weight (dry basis); process modifications and additions required to implement "best available technology" water quality controls; and installation of "best available technology" air emission controls. The new process began operation on June 24, 1980 and is being optimized to meet design objectives. Dry cobbing, fine screening and flotation additions to the concentrating process have reduced the silica content of Reserve's pellet from nine percent to five percent by weight. The process reclaims and reuses all process waters, stores all tailings in a zero discharge tailings basin and meets all air emission standards.

Jan 1, 1980

By Andrew Scogings

The current edition of The Australasian Joint Ore Reserves Committee (JORC) Code was published in 2012 and, after a transition period, the 2012 edition came into mandatory operation on Dec. 1, 2013. There is a significant change between JORC 2004 (Clause 44) and JORC 2012 (Clause 49) for the reporting of industrial mineral resources and reserves, which should be addressed by ASX-listed players in the industrial minerals space.

By Steven E. Mischler, Jay F. Colinet

The study analyzes the impact of the Continuous Personal Dust Monitor (CPDM) on reducing overexposures to coal mine dust. It compares compliance sampling data before and after the implementation of the CPDM and the 2014 MSHA dust rule. The results indicate a significant reduction in the percentage of samples exceeding the dust standard for various mining occupations, highlighting the effectiveness of the CPDM in improving miners’ health and safety.

Feb 22, 2022

By A. Toulet

Mining in Mexico has an immensely long tradition. In his first letter reporting to his sovereigns from Mexico in July 1519, Hernan Cortes wrote, "To our mind it is probable that this land contains as many riches as that from which Solomon is said to have obtained the gold for the temple ... " 1 But not only precious metals drew his attention; in 1524, short of tin needed for casting guns, he found it in Taxco. As an added bonus, those who went to find it "came upon a vein of iron which according to experts is of exceeding richness." 2 Since then, the mines of Mexico have yielded up enormous amounts of mineral and continue to do so. Mexico is one of the ten principal producers of minerals world-wide both in production volume and diversity. 3 Tens of thousands of tons of iron, sulphur, and coal come from its earth annually; it is the world's second largest producer of barite; third of antimony, fluorite, and graphite. 4 Copper, zinc, silver, molybdenum, arsenic and cadmium and others are wrested from its mines. The wealth is there; but maximizing its potential requires investment, technology, and markets that the government cannot itself provide. Thus mining, since the Mexican Revolution severely restricted by both law and policy, today looks to private investment to develop its potential. Beginning in 1989, Mexico's government cautiously moved to liberalize private sector involvement in mining; 5 using the experience gained from these initial regulatory changes, the current new Mining Law was adopted in 1992 6 and new Regulations were promulgated in 1993. 7

Jan 1, 1994

By Xinyang Yu

The flotation of diaspore, kaolinite, pyrophyllite, illite and the diaspore-kaolinite mixture were studied with a new cationic organosilicon quaternary ammonium collector entitled QAS222. The acting mechanism of the collector with the four minerals was analyzed by Zeta potential measurement and FT-IR spectrum analysis. The results indicate that the QAS222 was effective in the reverse flotation of the diaspore-bauxite mixture of different Al2O3 -to-SiO2 mass ratios (A/S ratio) at an optimum pulp pH of 11. The potentials of the four minerals increased when they were conditioned in the QAS222 solution; however, the potentials of the three aluminosilicate minerals increased faster than that of the diaspore, especially at pH>9. Furthermore, they were positive in a wide pH range, indicating that QAS222 has a strong adsorption on the surface of the aluminosilicate minerals and thus that these minerals can be floated. The FT-IR spectra analysis further indicates that, besides electrostatic adsorp-tions, formation of the hydrogen bond and ammonium absorptions, chemical adsorptions occur between QAS222 and the aluminosilicate minerals, which allow for the QAS222 to be strongly adsorbed on the aluminosilicate minerals. However, these reactions between QAS222 and diaspore at pulp pH=11 are weaker than those of the aluminosilicate minerals. Thus, surface adsorptions cannot be formed effectively, resulting in reduced floatability.

Jan 1, 2010

By Charles S. Robinson

The Henderson ore body is east of the Continental Divide in the Front Range of the Colorado Rocky Mountains about 50 miles west of Denver. The ore body is being developed for mining by workings that extend more than 3500 feet below the topographic surface. During construction of the mine workings, ground water in fractures in crystalline rocks has been encountered. From 1969 to 1973, Charles S. Robinson & Associates, Inc., in cooperation with the engineering and geologic staffs of the Climax Molybdenum Company, a division of Amax Inc., studied the ground water geology of the Henderson mine development area. Detailed geologic records of the Henderson mine were available as a result of the exploration, evaluation and development of the mine. Records of the flow, chemical composition and temperature of the ground water at and near the surface, from the entire mine, from portions of the mine, and from exploration holes drilled in the mine, were kept as the mine was developed. Where possible, ground water pressures in drill holes and changes in pressure with time, were recorded. The geologic, hydrologic and chemical data were correlated. The following conclusions were drawn from the correlations: The ground water in the Henderson mine occurs in fractures in Precambrian igneous and metasedimentary rocks and in a series of Tertiary intrusive rocks. Two zones of ground water were recognized; an active zone, in which the fracture systems are recharged and discharged annually into the surface water system, and a passive zone, in which the fractures were filled with water in the geologic past. Discharge from the passive zone is through mine workings that intersect the fracture systems. Discharge from a fracture or fracture system is initially high but decreased with tire!. The rate of decrease in flow (or pressure) is exponential. By measuring the change in flow with time, it is possible to calculate the amount of flow at some given period of time in the future. Based on changes in rate of flow and pressure, and the geology, and assuming rates of mining of the ore, it will be possible to predict the volumes of water that will have to be handled during the life of the mine and the area around the mine that will be drained by the mining operation.

Jan 1, 1976

By S. Komar Kawatra, J. J. Carlson

"It is widely known that steel made from iron ore pellets high in phosphorus is brittle. Removal of phosphorus from iron ores such as hematite has proven to be difficult. The majority of research on phosphorus removal from hematite ores has been focused on flotation. The purpose of this study was to assess phosphorus distribution under current operations at an existing hematite concentrator and determine how efficient the plant is at removing phosphorus. Objectives included: (1) Perform a phosphorus balance at an operating plant to assess phosphorus distribution under current operations; (2) Determine phosphorus removal efficiency of each separating unit and (3) Perform a quantitative liberation analysis to determine max phosphorus removal by physical means. Liberation was quantitatively determined using wet high intensity magnetic separation (WHIMS) to separate iron ore from liberated apatite (and other nonmagnetic compounds).It was observed that 61.2% of the total phosphorus entering Plant F was rejected during current operations. The desliming process was the most efficient step at removing phosphorus (45.1% P removed), whereas the flotation step was much less effective (16.1% P removed). Liberation analyses indicated that the deslime thickener may have been more efficient at removing phosphorus than the flotation circuit due to the greater abundance of liberated phosphorus in the deslime thickener feed. The scavenger returns stream was identified as having a high concentration of phosphorus and a possible point of phosphorus removal. However, liberation analyses indicated that only 32.4% of the total phosphorus in the stream was liberated. Grinding the scavenger returns to 80% passing 5.2 µm increased the amount of liberated phosphorus in the stream to 70.4%."

Jan 1, 2014

By D. A. Peacock

"INTRODUCTION Outer space technology and exploration have reached a tipping point so that mining and mineral processing in outer space is now a certainty and not a dream. Several competing companies, worldwide, are well on the way to building spaceships to land on the Moon and eventually mine the Moon and asteroids for volatiles, rare earth metals and Helium-3. The Google Lunar XPrize offers a $30 million prize1. China has recently landed a spacecraft on the Moon. The European Space Agency, with cooperation from the United States, has landed a spacecraft, Philae, on a comet. And, Mars One is planning a one-way trip to establish a settlement of humans on Mars. How and why are the Moon and asteroids and their resources of interest to private space industry and companies? Why are the Moon and asteroids viewed as a potential business venue? GEOLOGY OF THE MOON AND ASTEROIDS –WHY DO WE WANT TO MINE THERE? Space enterprises are actively working towards establishing and operating lunar and asteroid mining locations for resource extraction, resource processing, conversion to salable products, and distribution of the products and services in space and to Earth and beyond2. Forty-five years ago, the Apollo manned missions to the Moon returned rocks and regolith to Earth, which were studied and analyzed. What they found was that the Moon contains valuable minerals and resources. These minerals are largely due to meteor and asteroid impacts, which have, over eons, created this mineral rich regolith. These impacts have occurred on Earth as well, for billions of years, particularly early on in the history of the solar system. However, on Earth, wind, water, and vegetation have erased most of these impacts. On the Moon, in contrast, the only weathering is caused by subsequent impacts and the solar wind. The Moon regolith contains valuable rare earth minerals, platinum-group minerals (particularly where the Moon has been impacted by asteroids), volatiles (useful for processing and habitation), Helium-3 and titanium. Almost non-existent on earth, Helium-3 is abundant and accessible on the Moon and can be used in nuclear fusion power plants, producing much more energy than fission reactions and with much less radioactive waste. One of the main reasons Helium-3 is sought after as a fusion fuel is because there are no neutrons generated as a reaction product. Governments and private companies focus on mining of Helium-3 on the Moon as a basis for their economic models. Moon Express, one of the private companies who is planning on mining on the Moon, will recover moon rocks to fund its early operations25. Subsequently, it will recover Helium-3, platinum, and rare earth metals, as it engages in surface mining operations."

Jan 1, 2016

By J. L. Ellenberger, P. W. Jeran

A deep longwall coal mine was instrumented with a three-dimensional microseismic system in order to help determine the exact strata mechanics associated with the rock failure, redistribution of stress and the associated gob formation from the longwall. Overall, 5,000 well calibrated seismic events were recorded during the mining of the panel. Analysis of these events showed a close correlation between the seismic activity and advance rate, and that the majority of the recorded seismic activity occurs in the immediate area of the advancing longwall face.

Jan 1, 2002

By d&apos, L. R. Fletcher, Andrea. D. V., M. A. Peltier

The Bureau of Mines analyzed coal mine blasting accident data obtained from the Mine Safety and Health Administration (MSHA), U.S. Department of Labor. The data were examined to determine the causes, frequency, and severity of accidents in an effort to point out the most dangerous aspects of coal mine blasting. Accident data for the 14 years from 1971 through 1984 show that there has been a total of 43 fatal and 926 nonfatal blasting accident victims in surface and under- ground coal mining. This is an average of 3.1 fatal and 66.1 non- fatal injuries each year. Underground coal mining accounted for 60.5% of the fatal and 78.7% of the nonfatal accidents involving explosives and breaking agents in coal mining. In addition, since 1970 there have been 53 fatal and 20 nonfatal injuries that occurred when explosives were the ignition source for dust and/or methane explosions in underground mines. Abstracts from 297 accidents that occurred from 1978 through 1984 were also examined to determine accident causes. Most accidents occur during scheduled blasting, and failure of the blast area security system is the leading cause. Blast area security problems in surface mining are failure to clear the blast zone, failure of personnel to follow instructions, inadequate guarding, and failure to retreat to a safe location and/or take adequate cover. Other common causes in surface mining include premature blasts, excessive flyrock, and misfires. In addition to the above causes, accidents in underground coal mining can be due to rockfalls triggered by the blast, unexpected breakthroughs, fumes, and incidents associated with Airdox-type systems.

Jan 1, 1986

By J. F. T. Agapito

Experience at Energy West Mines in the Wasatch Plateau Coal Field, Utah, has shown that longwall face bursts occur mostly near the tailgate when extracting the third adjacent longwall in a panel section where depths exceed 610 m (2000 ft). It is believed that this is due to a combination of cover depth and side abutment stresses created by the widening of a pressure arch formed by interlocking and bridging of large blocks of" very competent strata. The 60-m-thick (200 ft) Castlegate Sandstone probably plays a key role in pressure arching. This paper presents a back-analysis of the location and magnitude of the stresses associated with face bursts that occurred when mining the 7th Right Longwall at the Deer Creek Mine. Improvement of these conditions may be achieved by widening the longwalls to attain critical subsidence width sooner while mining the second long-wall, and to reduce stresses at the face. Wider longwall faces, however, increase the chance of sandstone channel interception often associated with bursts. Satisfactory mitigation of face bursts beyond cover depths of 610 to 670 m (2000 to 2200 ft) may be difficult without using destressing techniques. The hydraulic fracturing/liquid infusion technique seems to offer the best possibilities for application in longwall mining.

Jan 1, 1997

Iron removal using biologically produced organic acids was investigated as a treatment option for the production of refractory grade bauxite. A leaching solution containing 98mM oxalic and 67mM citric acid was prepared from a sucrose medium using for fermentation the fungus Aspergillus niger. The leaching capacity of the metabolic product was tested on a bauxite sample containing 16-19% iron (as Fe2O3). Aerobic and anaerobic leaching tests were carried out at pH 3, 50°C and in the absence of light. Results indicated that more than 80% of total Fe can be removed from the ore, when the sample is finely ground and applying a two stage treatment. The presence of oxygen was seen to affect adversely the kinetics of the process, suggesting that leaching follows a reductive mechanism. Experiments that were carried out with different particle size fractions indicated that for obtaining efficient removal of iron particles should be finer than 0.63mm. Reduction of the operating temperature from 50 to 30°C caused a decrease in the rate of iron removal by more than 10 times.

Jan 1, 2006

By Thomas P. Meloy

Comminution is an old art. Unfortunately the analysis of the unit operations has been handicapped by the lack of both theoretical and experimental information. Two types of infor¬mation are needed, one an understanding of what happens when a particle breaks in a brittle manner; and two, an understanding of what happens when the daughter fragments pass through the mill. This paper is concerned with the former, the catastrophic fracture of a brittle solid. Recently, successful theoretical attacks on the frac¬ture of brittle solids have yielded significant-results. New experimental techniques are yielding insight into the physical phenomenon occurring during brittle fracture. Many of the re¬doubtable shiboliths of the last century are either being laid to rest or verified.

Jan 1, 1965