Search Documents

By Verya Nasri, Heather M. Ivory, Kevin Clarke, Eric Cole

Development of the New York City Water Supply System The New York City water supply system serves a population of almost nine million, including residents in neighboring counties. Peak day demands on the system are currently running at about 70 m3/sec (about 1,600 mgd), which is significantly lower than in the 1990s. This trend of reducing demands over the past 25 years, which has been experienced in other major urban centers in the US, is mainly the result of conservation measures and increased cost consciousness on the part of water users. In the long term, demands are expected to once again follow an increasing trend with population growth, so that by the end of the planning horizon of these studies, the year2045, the peak day demand is expected to increase to about 85 m3/sec (2,000 mgd).The system is served largely by surface water sources, regulated by a system of 19reservoirs and three controlled lakes, which are connected to the City by a series of aqueducts, the longest of which is about 87 km (54 miles). The total storage in the sys-tem amounts to about 560 billion gallons, providing a system firm yield of about1300 mgd. The Delaware system provides about 50% of the City’s water, the Catskill about 40%, with the remaining 10% provided by the Croton. The system as a whole, which is shown on Figure 1, has been built up over the past 150 years, and is truly a marvel of engineering. The Catskill and Delaware aqueducts both discharge into Kensico Reservoir, which is a daily balancing reservoir located in Westchester County about 24 km(15 miles) north of the New York City line. The two aqueducts extend south for a further 14 miles to combine again at Hillview Reservoir in the Bronx, which provides hourly balancing storage for New York City system. The Croton aqueduct runs nearby as shown on Figure 2, but does not connect into the two reservoirs. From Hillview Reservoir the water is supplied to the city via three main distribution tunnels, known as City Tunnels 1, 2, and 3. City Tunnel No.1 was developed in the 1920s as part of the Catskill system. City Tunnel No. 2 followed in the 1960s as part of the Delaware system. City Tunnel No. 3 (CT3) is partly under construction and partly in operation, and is being implemented to permit the other distribution tunnels to be taken out of operation for the first time for inspection and maintenance. Presently CT3 is supplied with water from Hillview Reservoir via a large underground valve chamber, the Van

Jan 1, 2007

By Tim O’Neil

Question: Looking forward, do we face a future in which energy markets, energy policy and energy conflicts threaten to preoccupy, if not dominate, our concerns over economic growth, national security and domestic tranquility? The answer is, we may indeed face such a future. Question: What oil resource is comparable in size to the reserves of Saudi Arabia and presents a tremendous opportunity? The answer, the oil sands in Alberta, Canada. Question: What is the largest mineral staking rush in North American history, still under way? It has so far led to the development of two large mines. The answer is the Point Lake diamond strike in Canada’s Northwest Territories. It led to the development of the Ekati and Diavik mines.

Jan 1, 2004

By Jürg Schlumpf

Concrete is one of the decisive construction materials, also for the AlpTransit Gotthard Tunnel. The client has many requirements, and many are the solution possibilities that concrete systems can offer. Cement producers and concrete admixture manufacturers have been challenged to design and test jointly concrete systems for cast and sprayed concrete. The testing operation followed the scenario laid out by the Gotthard AlpTransit Project management?s instructions ?Testing system for concrete mixes.? Various supplier teams have applied for the concrete systems for sections Amsteg/Erstfeld, section Sedrun and/or sections Bodio/Faido and have also followed through with the tests. As was to be expected, the rate of failed mixes matched the level of the requirements. Thanks to this system, it was nevertheless possible to test complete concrete systems for all sections and to get them approved. The joint ventures tendering for the contracts were allowed to include only approved mix designs in their bids. Workability and durability are of paramount importance for cast and sprayed concrete mixes. Durability is influenced by the chosen mix design where binder concept and well-defined water content, i.e., impermeability, are determinant. Aggregates for AlpTransit are to be considered as given. The concrete mix design also determines workability. Because ambient conditions and also requirements with respect to workability are subjected to change, it is necessary that the mix designs include control measures. The choice and number of components for the concrete systems (cement, additives and admixtures) allow adaptation to changing conditions. For AlpTransit such adaptive measures must meet very strict requirements.

Jan 1, 2008

By Euclid P. Worden

INTRODUCTION Today, conventional raise boring is an accepted method of development in underground mines and on major construction projects. Over the years that this technique, and its associated machines and tools, have been under development, many articles have been written on the subject. To a great extent, these papers have reported operating results of one or more specific projects or have been generalized reviews of state-of-the-art machines and tools. This paper is intended as a review of the technique from an operational standpoint. Conventional raise boring, as opposed to the related variants box hole drilling and underground blast hole drilling, is a two step process consisting of the pilot hole drilling and reaming cycles. This author has covered the subject of pilot hole drilling in another article (1) . A good review of the current machines and equipment has been presented by Monroe (2) and an overall review of this entire technology was published by E&MJ (3) and Mining Journal, April, 1983 (4) . The subject of the reaming cycle is presented here together with some of the technical aspects of how the drilling tools are intended to be used. OPERATIONS Bit Change After the pilot bit has broken through at the end of the pilot hole cycle, a changeover takes place at both the machine and

Jan 1, 1985

By K. R. Griffin

Explosions in underground coal mines have been a serious safety concern since the advent of mining; despite significant technological advances, they are still occurring. Parameters such as barometric pressure, geological changes, and changes in ventilation can contribute to an explosion. These factors can be monitored with available and developing technologies to create algorithms that predict when explosions are more likely to occur. This paper reviews current underground atmospheric monitoring systems and related regulations around the world. In addition, suggestions for improvement and implications for explosion prevention are discussed.

Jan 1, 2011

By H. Sis, D. Dahlin, S. Chander, C. Summers

Bench-scale selective-flocculation tests were conducted on samples of Florida and Western phosphate process tailings. Physical, mineralogical, and surface characteristics were determined for both types of samples. The flocculation tests investigated dispersant and flocculant types and doses, pH, and slurry percent solids, while other parameters were held constant. Where selectivity was achieved, phosphate minerals remained dispersed, whereas silicate minerals flocculated and settled. In single-stage tests, flocculants having low to medium anionic character effectively upgraded products at moderately elevated pH. Multiple-stage tests, and tests in which flocculants of lower molecular weight were used as site-blockers, gave improved results.

Jan 1, 2002

By Terry W. Mellors, Robert J. F. Goodfellow

The underground industry has been forced to reconsider risk management sincethe introduction and implementation of the “Joint Code of Practice for Risk Management of Underground Works in the UK” published in 2003 and the subsequent international version published by the ‘International Tunneling Insurance Group’ (ITIG) in January 2006.What does this mean for major tunnel projects in the US and elsewhere? The discussion will highlight the implementation of the Codes to date, risk management principles embodied in the Codes and the use of risk registers as a projectmanagement tool and the management of risk.

Jan 1, 2007

By Ning Wang, Tengfei Guo, Wanyan Li, Hanjie Wen, Hannian Gu, Zehai Li

Bauxite residue (red mud) is an alkaline waste derived from the industrial process for extraction of alumina from bauxite ore. Some bauxite residues contain considerable concentrations of critical metals, for example, rare earth elements. Lithium in red mud was also reported as a potential resource. In the current study, a Li-rich red mud was leached using acetic acid to investigate the leaching behavior of lithium followed by neutralizing with hydrochloric or oxalic acid. By neutralizing red mud using diluted hydrochloric acid (0.01 mol/L), 58.04–60.27% of lithium was leached using 25% acetic acid at 95 °C for 60 min. In the meantime, more than 95% of sodium and 85% of calcium were also dissolved in the leachate solution. While oxalic acid (0.5 mol/L) was used to neutralize red mud prior to acetic acid leaching, lithium performed lower leaching efficiencies (42.41–46.88%) in comparison of using of hydrochloric acid–neutralized red mud. Nevertheless, these leaching efficiencies of lithium were close to that of calcium and much higher than those of sodium under the condition. In this study, 25% (v/v) of acetic acid, at 85 °C for 60 min, was demonstrated as optimum conditions for lithium extraction from oxalic acid–neutralized red mud using acetic acid. The results would be useful and of interest for lithium recovery and purification from red mud.

By D. McBride

Representative samples are required from process streams in order to accurately measure chemical and physical characteristics. This information can then be used by process operators and metallurgists to evaluate the process and effect control actions for the operation. The capture and presentation of representative samples can be critical to measuring values, such as elemental analysis and particle size, with on-line or near-stream analyzers. A comprehensive multi-physics model has been developed and used to better understand the effects of slurry flow and particle segregation under certain operating parameters. An algebraic slip model coupled with a free surface algorithm is used to track motion and position of particles and phases within a specified geometry.

Jan 1, 2009

By Jacek B. Stypulkowski

This paper discusses the challenges faced by the design team of the under-river crossings of electric transmission feeders in New York City, a densely populated urban area. The under-river crossing of a 345 kV feeder was initially designed as Horizontal Directional Drilling (HDD), but was redesigned as a utility tunnel because of site con¬straints on both sides of the river. Multiple studies addressed location, available tech-nologies and costs. Multiple soil investigation phases addressed design aspects of HDD, as well as tunneling. Contractual issues varied from a design build alternative with Geotechnical Data Report (GDR) to design tender approach with GDR & Geotechnical Baseline Report (GBR).

By J. D. Morgan

Introduction In 1986, the US economy passed the $4 trillion mark. However, the value of domestically processed materials of mineral origin fell slightly to $240 billion. The value of metals produced from US ores was unchanged at $5.6 billion, as was recycled scrap at $4 billion, while the value of industrial minerals rose slightly to $17.9 billion. Consumer demand strongly affects mining and the US economy is relatively saturated with longlived products. Moreover, in recent years there has been a steady increase in consumer, mortgage, and federal debt, inhibiting new purchases of goods. Motor vehicles and housing are major traditional markets for mineral materials. However, the 242 million US citizens already possess 170 million licensed motor vehicles and 92 million dwelling units. In 1986, domestic motor vehicle production fell 3%, to 11.3 million units, while new housing starts rose slightly to 1.8 million units. Nearly all mineral commodities move relatively freely in world trade. As detailed in Figs. 1 and 2, in the last three decades world production of major mineral materials has greatly increased. At present, substantial excess productive capacity exists not only in the US but also in many other countries. Consequently, the US mineral industry is encountering increasing competition from other sources, along with increasing competition from newer, engineered materials. For example, US production of plas¬tics has risen from 900 kt (1 million st) in 1950 to 22.7 Mt (25 million st) in 1986 - on a volume basis significantly greater than steel. Plastics, too, are mineral-based materials, some 7% of petrochemicals going to their manufacture. 1986 saw increased calls for protection. But President Reagan, in his 1987 State of the Union Message and Economic Report to the Congress, reaffirmed adherence to a policy of free and fair trade. However, he stressed the need for increased efforts to open foreign markets to US exports and to increase competitiveness of US industry US imports of mineral-based minerals in 1986 were valued at $40 billion and exports at $24 billion. Strategic minerals As detailed in Fig. 3, imports supplied a significant proportion of total US consumption of several important materials, including many classified as "strategic and critical." There were no changes in stockpile policy during the year. Congress debated the President's 1985 proposals to reduce stocks of World War II-type materials and to focus more on high technology materials needed for the cutting edge of future military material. But no final action resulted. However, Congressional concern about apartheid in South Africa did result in increasing pressure to limit imports of South African minerals. Meanwhile, the National Critical Materials Council in the Executive Office of the President intensified its efforts to be better able to advise the President. The Defense Production Act provides authority for priorities and allocations, supply expansions, voluntary agreements, and

Jan 5, 1987

By H. Tudeshki, A. Tayebi

"The large extent of global production and consumption of aggregates from quarries, grabs one´s attention and makes its substantial and essential standpoint in the world today pretty clear. A great amount of aggregates is utilized in civil engineering applications such as road construction, railway industry, concrete production, etc. Considering this fact that igneous rocks display a higher strength and abrasion resistance, this type of rock is preferred in the field of civil engineering. For all these applications, rock quality assurance is a key factor and certainly unavoidable, and it has great influence on the quality of constructions in civil engineering. One of the major problems encountered by both the producers and users of igneous rock is the fact that, with the passage of time, some specific rocks lose their strength, up to a complete loss of structure or in other words, their disintegration and degradation. In the last decades, different methods and procedures such as Glycol test, methylene blue dye test, as well as the Los Angeles test have been introduced to distinguish these rock properties, and to identify these problems. However, as these methods are time consuming, hard to perform, only to be applied to hand-piece samples, requiring special laboratory equipments, and only possible to be accomplished under laboratory conditions, their application has always been limited to some specific cases, and they are neither recommendable nor advantageous. In addition, these methods provide partially different results for the same rock. To address this widespread quality management problem of the quarry industry, a relatively quick, easy and user-friendly approach is necessary. It calls for a systematic solution with a device that can simply be used day to day in a mine for quality control of the quarry´s daily production. This scientific research is concentrated on developing a systematic method for early recognition and diagnosis of rock quality, in order to control and manage the quality of the quarry production in advance. This method was developed, based on the procedure of the magnetic susceptibility measurement. The obtained values can lead to valuable information regarding the quality of the rock and allows the quality control process to be accomplished and performed at the borehole location. This approach has been assessed through extensive field and laboratory studies. A detailed and comprehensive discussion will be made on the results of the experiments. The advantages and impacts of the application of this method, on increasing the reserves and environmental protection are also discussed."

Jan 1, 2011

By T. Tafi

The Ute-Ulay project area is located approximately five miles west of Lake City, in Hinsdale County, Colorado. The Ute-Ulay Mine site is approximately one mile east of the project area. The elevation of the site is 9,200 feet and is adjacent to Henson Creek (Figure 1) [ ] The Ute-Ulay Mining complex is an inactive gold, silver, and zinc mining/milling operation, that operated from the 1880?s until the 1970?s, and sporadically into the late 1990?s. The mining complex comprises several levels of underground mines, a flotation mill, and an abandoned town site. Due to the narrow, steep sided canyon, milled tailings were pumped upstream one mile in a sluice box to a wider section of the canyon, and deposited into five tailings impoundments and one berm located between the impoundments. An estimated 9,000 cubic yards (yd3) of fine grained tailings were located in the impoundments adjacent to the creek. The Ute-Ulay project area consisted of the mill tailings impoundments located upstream from the historic mine.

Jan 1, 2011

By Zephaniah Varley, Dominic Parmantier, Paul Schmall, Richard Martin, Red Robinson

Sequential excavation of the Beacon Hill Station has been accomplished in highly complex and inter-layered sand, silt, and clay soils with multiple perched groundwater tables. Successful excavation has required the installation of a deep dewatering well system used to depressurize sand layers above and within the excavated tunnel faces. In addition, the presence of sand layers in the crown of the Platform Tunnels required jet grouting at depths of up to 49m (160-ft). This paper discusses the design intent, construction, and effectiveness of the dewatering system and the selective jet grouting of sand horizons and shaft break outs for the successful construction of the deepest SEM station excavation ever completed in the United States.

Jan 1, 2007

By A. Korchevisky

Environmental self-monitoring is one of the advanced approaches for industrial sustainability programs. Organization for Economy Cooperation and Development (OECD) defines self-monitoring as ?the system of organizational and technical measures put in place and financed by [the] regulated subject? in order to ensure their compliance with regulatory requirements?1. Self-monitoring is beneficial for industrial operators, communities, and governments. Industrial companies use self-monitoring as a central element of their compliance management that allows them to fulfill their duties, obligations, and to avoid citations. When industries control their emissions and ensure workers are not exposed above the regulated limits, communities are better. It is impossible for an EPA, OSHA, or MSHA inspectors to be close to every emission source or workplace full-time. It is much more effective for industries to self-monitor, under due supervision. Occupational conditions are a very important part of industry and health and safety self-monitoring should be highly prioritized. In this paper we will research the regulatory basis and best practice of occupational self-monitoring. We will show that not only is self-monitoring a vital element of an occupational health & safety management system, but that you need a management system for affective monitoring.

Jan 1, 2012

By T. J. Lynch

A new class of polymeric dispersants for industrial minerals has been synthesized and evaluated. Currently available dispersants give initial low viscosities at high mineral loadings, however slurry viscosities can rapidly double or triple on standing over the first several days. The new dispersants give low initial viscosities that are more stable and maintain a lower viscosity for at least one month. The new dispersants are made possible by controlling the polymer molecular weight distributions during their manufacture such that essentially all of the dispersant is adsorbed onto the mineral surface, preventing depletion flocculation.

Jan 1, 2012

By Yoshihiro Kawarabata

INTRODUCTION With only about 30% of Japan's entire population served by sewer systems at the end of 1980, extensive sewerage construction programs have been implemented. As major sewer networks in large cities are near completion, construction of smaller sewer networks in less populated areas and branch sewers in urban areas is on the rise, where a demand for sewer tunnels of 600mm to 1500mm diameter is very heavy. The pipe jacking technique, usually employed to excavate such small diameter tunnels, therefore has become the subject of further technological development and sophistication to cope with the increasing volume of construction. At the 1979 RETC, the state of the art on the slurry shield tunneling method at that time was reported. This paper is a follow up to the last paper and discusses a newly developed boulder crushing equipment and automatic pipe jacking system for the slurry shield method and their application. Such technological advancement as high-degree mechanization and automation will significantly improve tunneling operations in response to the aging society to come. Through application of the technique on so called factory automation, this is a step towards field automation for the construction industry.

Jan 1, 1983

By A. J. Monhemius, R. G. Reddy, G. W. Warren, E. Peters

Thermodynamic solubility of chromium in pickling solutions (i.e., HF- HN03-H2O solutions) was determined as a function of HF and HNO3 acid concentrations at 298K. Pure Cr, AISI type 316 and 416 stainless steel were used in this study. The results showed that the solubility of Cr increased with increase in the concentrations of HF and HNO3 acids in solutions. The solubility of Cr increased in the order of pure Cr > 416 SS > 316 SS. The theoretically calculated Cr solubility data were in reasonable agreement with the experimental data.

Jan 1, 1993

In spite of a global economy that continues to seesaw and a U.S. Congress that is at odds with the president and themselves, cities around the world are still spending billions on their infrastructure. And that bodes well for the underground construction and tunneling industry and the professionals who work in it. In June, 1,405 of those professionals gathered in San Francisco, CA for the Rapid Excavation and Tunneling Conference (RETC). In addition to the first rate technical programming, attendees were able to see first-hand the latest in tunneling technology from 127 exhibitors who occupied 152 booths. Two short courses preceded the conference and two field trips were offered following the conference.

Jan 1, 2011

By Jack Magtoto, Lysa Voight, Tom Martin, John Forero

SUMMARY Commitment by all parties to partnering goals established early in the contract aided Affholder, Inc. in constructing 2,360m (7,700') of soft ground tunnel in Rancho Cordova, CA. Despite two zones of known contamination, encountering a zone of loose cobbles and boulders in a matrix of flowing sand, some perched water tables and a flooded tunnel after 2 upstream safety plugs failed, the Contractor finished the work 33 days early and only 1.91% over his original bid.

Jan 1, 2007