Search Documents

By M. S. Klima

A 25-mm diameter dense-medium cyclone was tested to investigate the effects of geometry and operating conditions on cyclone performance when processing -150 I'm coal. The emphasis was on examining those variables (e.g., flow rate and inlet velocity) which impact the separation kinetics (specifically the number of g's and the mean retention time) and the occurrence of apparent bypass. Apparent bypass, indicated by partition curve "tails", results from the short circuiting of the feed coal to one or both of the product streams and represents a loss and/or contamination of the clean coal. This paper presents the results for this series of tests.

Jan 1, 1993

By H. Sevim

Three transportation and handling alternatives for delivering dry coal combustion residues from power plants to underground coal mines were evaluated technically and economically. The objective was to transport, handle, and inject the residues into the old workings of the mine at a minimum cost. This objective was accomplished in two steps: I) Simulation models were developed and utilized in identifying technically feasible designs in each alternative, 2) Technically feasible designs were economically evaluated to obtain the cost-per-ton of material transported. The designs that provided the minimum cost-per-ton were declared optimal An analysis was conducted for varying distances and tonnages to reveal favorable operating ranges of each alternative.

Jan 1, 1996

By Martial P. Corriveau

The preparation of coal is essentially the same for export as it is for the domestic market. The big difference, I would say, is that, while coal for certain domestic uses (utilities, for instance) need not always be of the highest quality, as long as it is uniform, the buyer of coal for export invariably demands a well-prepared, top-quality product. And he is willing to pay for it, as long as he knows what he is buying. This is where quality control enters the picture. The day is long past since the export market was the dumping ground for coals which could not be sold on the domestic market. Today, the export buyer wants American coals not so much for a price but for the necessity of blending the American coals with foreign coals to achieve the desired chemical and/or physical characteristics, To blend intelligently, he must know in detail what are the qualities of the coals to be blended. Sampling and chemical analysis facilities at the piers provide the information on the coals exported, These facilities are maintained for the export buyer by independent laboratories; however, in one instance, the buyer operates his own laboratory. With very few exceptions, and Clinchfield?s Moss No. 3 mid-volatile coal is one, cargoes shipped overseas are loaded as blends of two or more coals. Up to now, foreign requirements have not been too clearly defined; therefore, shippers must be prepared to blend mixtures of the desired combination. Successful blending requires an accurate knowledge of the coals shipped. And this makes it necessary for the coal producer to maintain his own control laboratory.

Jan 1, 1959

By R. Benemelis

The existence of resins in some coal deposits in various parts of the world has been known for many years. These resins vary considerably in chemical structure and properties. The resin that is found in Utah coal, however, is rather unique, and has properties particularly attractive for the manufacture of printing ink mastics and adhesives. This resin is a rather dark, very high melting point, low molecular weight hydrocarbon resin. Its typical properties are shown in Table I. Its largest use by far, has been in the printing ink industry. The history of Utah coal resin is interesting, but unfortunately one of disappointment and failure.

Jan 1, 1990

By Paul L. Russell, R. G. K. Morrison

9.1-CLASSIFICATION OF MINERAL DEPOSITS AND ROCK MATERIALS After a mineral deposit has been discovered, delineated and evaluated, the next step is to select a mining method that is physically, economically and environ- mentally adaptable to recovering the mineral from the deposit. The term "mineral deposit" is used to denote a concentration of mineral (including rock and coal). Even where there is considerable past experience available, many of the critical design criteria must be determined utilizing only information obtained from an examination of exploratory drill core specimens. The factors that affect this selection are as follows: (1) the spatial characteristics of the deposit (size, shape, attitude and depth); (2) the physical (or mechanical) properties of the mineral deposit and surrounding rock; (3) ground water and hydraulic conditions; (4) economic factors, including grade of the ore. comparative mining costs and desired production rates; and (5) environmental factors, such as the preservation of the surface overlying the mine, and the prevention of air and water pollutants. Of these factors, the spatial characteristics of the deposit and the physical (or mechanical) properties of the mineral and surrounding rock limit the methods that can be employed to mine it. Six types of mineral deposits are recognized, as follows: 1. Massive-A deposit of considerable lateral and vertical extent in which mineralization (or ore) is relatively uniformly distributed. Disseminated copper ores are typical deposits. Dome salt also is included in this classification. 2. Bedded or Tabular-A mineral deposit that parallels the stratification, most often in sedimentary rock, usually laterally extensive, and of limited thickness. Most coal measures and some evaporite mineral deposits (e.g., potash) fall in this class. 3. Narrow Vein-A zone or belt of mineralization (ore) typically long, narrow (less than 10 ft), often dipping steeply, and usually lying within boundaries separating it from neigh- boring rock. Many gold and other metallic minerals occur in narrow veins. 4. Wide Vein-As defined under narrow vein except that the vein thickness is greater than 10 ft. 5. Lentictclar or Pocket-An isolated ore body, or an enrichment of limited vertical and horizontal extent in a massive, bedded or vein deposit. Lead, zinc and iron ores often occur in this type of deposit. 6. Placer-A surface or near-surface deposit, usually tabular and may be of consider- able areal extent, containing mineral particles (e.g., gold, platinum) in detritus (e.g., sand, gravel). The rock materials associated with mineral deposits are classified as follows: 1. Detritus-Sediments and other accumulations of solid particles produced by the mechanical and/or chemical disintegration of rocks, and usually having a low cohesive strength and very low compressive strength (e.g.. soil, sand, gravel, alluvium, playa). 2. Jointed and Fractured-Unbonded-A rock mass, often occurring on or near the surface or in fault zones, in which the joints or fractures contain alteration or decomposition

Jan 1, 1973

By R. Bhima Rao

Performing a magnetizing roast in a furnace or kiln is a well-established technology. However, the use of microwave heat for the magnetization of hematite in the beneficiation of ferruginous bauxite is a new approach. This paper reports on an investigation of this procedure, which is followed by comminution and magnetic separation. The results of this investigation indicate that a nonmagnetic product containing 80% A1203 and 2.5% Fe203 with a recovery of 80% can be made from a crude bauxite ore containing 55.9% A1203 and 5.6% Fe203. This product is suitable for refractory use. The mechanism is explained by the ability of the microwave radiation to heat specific points within the bauxite. These heat-specific points are at the location of iron minerals. In a reduced atmosphere, the microwaves promote faster conversion of the iron minerals to a magnetic phase, which improves the magnetic-separation process.

Jan 1, 1997

By J. A. Luppens

Five years ago, Phillips Coal Company decided replacing mainframe/workstation programs with a new package of PC software was clearly the best solution for computer reserve modelling. The system chosen was actually three programs distinguished by their power, cost, flexibility and integration, and ease of learning and use. Phase I involves the use of the "StratiFact" program for borehole data management and seam correlation. This phase is probably the most neglected, yet critical aspect of reserve evaluation. Phase II employs the "PC/Cores" package for modelling and volumetrics. Phase m is "PC-Cut" which provides mine planning tools including an automated cut generator.

Jan 1, 1996

By Joseph A. Kantor

Several wall rock porphyry or pyrometascmatic copper deposits occur within the metamorphosed Paleozoic formations along the northern and eastern flanks of the Little Dragoon Mountains. Rocks ranging in age from Precambrian to Recent occur in the area. The Tertiary age Texas Canyon Quartz Monzonite intruded the sedimentary section in the eastern half of the range metamorphosing the Paleozoic carbonate units to tactites composed of garnet, diopside, and tremolite. Copper, zinc, and molybdenum minerals deposited in sites which are structurally controlled and stratigraphically favorable. Because the deposits are covered by alluvium, the information on structure, alteration, and mineralization is based upon a study of the diamond drilling programs. The mineralized district can be divided into four areas: 1) The Johnson Camp copper-zinc deposits; 2) The Dragoon copper deposit; 3) The I-10 copper-molybdenum deposit; 4) The Strong & Harris copper-zinc deposit. On the southwest end of the range beneath alluvial cover, the Cretaceous Bisbee Group was thrust over Precambrian and Paleozoic formations. The Tertiary Texas Canyon Quartz Monzonite intruded and metamorphosed them. In the upper plate, the Cretaceous sediments near the intrusive were metamorphosed to metaquartzite and andalusite and sillimanite schists. In the lower plate the Martin and Horquilla formations were marbleized. The lower Abrigo was metamorphosed to epidote rich calc-silicate tactites and biotite hornfels. A composite geologic cross section, based upon diamond drilling,, through the Dragoon copper deposit is shown in Fig. 1. The geologic events which formed this deposit are: 1. A faulted section of Precambrian Pioneer formation and diabase and Cambrian Bolsa and Abrigo formations was thrust over Pennsylvanian Horquilla formation. The Dripping Spring quartzite if present, has not

Jan 1, 1977

By H. Kempton

New methods for remediating metals-contaminated groundwater include in-situ emplacement of highly adsorptive substrates to permanently retard solutes. Substrates are introduced by sequential injection of soluble components that precipitate in the aquifer, forming a permanent high-retardation zone. This method overcomes the factors that limit pump-and-treat remediation; i.e, long-term source loading and slow desorption. Column tests demonstrated efficient substrate emplacement, increasing retardation coefficients of Cr(VI) by 20 and As(V) by 40. Similar effectiveness is expected for other heavy metals. Simulations using a coupled advective-geochemical model accurately matched substrate emplacement and arsenic attenuation, allowing extrapolation to other constituents and larger-scale applications.

Jan 1, 1999

By Jack W. Eloranta, Michael J. T. Orobona, Peter R. VanDelinder

Ore blending for process optimization is becoming an increasing factor for managing cost and productivity. Economic mining and processing a very low value ore in an extremely competitive market results in constant cost-cummng initiatives. The inherent conflict between the lowest possible mining cost and the lowest possible milling cost is reviewed here in the context of blasting for autogenous mills. Iron ore blending focuses on a number of properties-liberation values, weight recovery and concentrate silica being the most important. Other chemical and metallurgical factors are also commonly controlled. Recent research has fueled an emerging interest in blending on physical ore properties as well. Fully autogenous mills rely on the large, competent fraction of crushed feed to act as grinding media. Previous test work indicated that Hibtac mills require specific amounts of 6- to 10-inch ore. High recirculating loads require a steady influx of large rock fragments. Blast designs, therefore, are presently characterized by wide patterns and low powder factors. Current efforts are aimed at improving mill throughput while reducing overall energy costs. Based on research and published case studies and the advent of optical measuring devices, Hibbing Taconite Company has embarked on a blast optimization program to identify optimum mill feed and to design blast fragmentation goals for each geological unit and each mining area. This paper outlines the preliminary findings of an ongoing, broad-based team effort which requires close cooperation of geologists, mine engineers, crushing and milling personnel. Three specific areas of investigation are reviewed: I) Historical relationships between powder factor and mill performance, 2) Blast fragmentation modeling using the Kuz-Ram model, and 3) Drill

Jan 1, 2004

By D. F. Lillie

The milling plant of Bicroft Uranium Mines Limited has been in operation for a period of 2 years. During this time many changes, both physical and chemical, have been made in an effort to improve plant efficiency. Investigational work has been facilitated greatly by the fact that the Bicroft mill consists to a large extent of two parallel circuits; however, the number of inter-related variables is great, and it is difficult to measure, let alone control, all of them simultaneously. The Bicroft mill staff feel that much progress has been made, but there is much yet to be done and many questions still to be answered. The property of Bicroft Uranium Mines is located in Cardiff Township in the Highlands of Haliburton County, southeastern Ontario, some 140 miles northeast of the city of Toronto and 70 miles due north of Lake Ontario. The ore-bearing dikes are classed as mafic, non-segregated, syenite and granite pegmatites. Microline, microline perthite, quartz, uraninite, uranotharite, fluorite, titanite, cyrolite, calcite, pyrite, pyrrhotite and molybdenite as important accessories. The mill was designed for a nominal capacity of 1,000 tpd with all sections except grinding, leaching and clarification capable of 1,500 tons. Feed was entered to one mill unit on October 29, 1956 and to the second parallel line on November 13. The total feed rate was at 1,000 tpd on November 15. The first precipitate was produced on November 12. By August 1958 the average entry had been increased to 1,410 tpd without the installation of any additional major equipment. The overall recovery has been greater than 93,0 pet do several months, but a recovery of 92.5 pct appears to be most economical. Operating time for 8 months in 1958 has been 97.1 pet although all grinding mills were relined during this period.

Jan 1, 1959

By N. Damiano, C. Zhou, B. Whisner, M. Reyes

"The Industrial Internet of Things (IIoT), a concept that combines sensor networks and control systems, has been employed in several industries to improve productivity and safety. U.S. National Institute for Occupational Safety and Health (NIOSH) researchers are investigating IIoT applications to identify the challenges of and potential solutions for transferring IIoT from other industries to the mining industry. Specifically, NIOSH has reviewed existing sensors and communications network systems used in U.S. underground coal mines to determine whether they are capable of supporting IIoT systems. The results show that about 40 percent of the installed post-accident communication systems as of 2014 require minimal or no modification to support IIoT applications. NIOSH researchers also developed an IIoT monitoring and control prototype system using low-cost microcontroller Wi-Fi boards to detect a door opening on a refuge alternative, activate fans located inside the Pittsburgh Experimental Mine and actuate an alarm beacon on the surface. The results of this feasibility study can be used to explore IIoT applications in underground coal mines based on existing communication and tracking infrastructure.IntroductionThe U.S. approach to health and safety in mining has historically been reactive in the sense that health and safety regulations and mandates have traditionally been passed as a result of tragic mining accidents. An example of this is the Mine Improvement and New Emergency Response Act (MINER Act) of 2006, which was passed as a result of several mining accidents where tracking of and communication with underground personnel were severely limited. While this reactive approach has led to the development and implementation of highly impactful safety interventions and safety practices, there exists a technological revolution that can shift the paradigm toward a proactive approach based on preventative methods: Internet of Things (IoT).IoT is the network of physical objects, or “things,” embedded with electronics, sensors and connectivity to enable that network to achieve greater value and service by exchanging data with the manufacturer, operator and/or other connected devices (Atzori, Iera and Morabito, 2010; Gubbi et al. 2013). It should be noted that IoT has been defined from various perspectives, and hence numerous definitions exist in the literature. The apparent ambiguity of the IoT definition might be due to the fact that IoT is syntactically composed of two terms: the Internet and things. The first word pushes toward a network-oriented vision, while the second tends to put the focus on generic objects. The traditional Internet can be viewed as an internet of computers, so things connected to the Internet are computers only. IoT extends the internet by allowing other generic things that are commonly found in daily life, such as refrigerators and cars, to be interconnected through the Internet, thus creating a bridge between the virtual world and the physical world"

Jan 12, 2017

By B. Beatty

Discussion by B. Beatty This is a response to M.J. Hrebar's paper, which tracks in detail the highly productive stripping capabilities of modern large bulldozers at two separate installations. It proves the old adage "economies of scale" and quantifies the advantage of being able to move large loads of dirt over comparatively short haul distances by sliding rather than carrying the load. This discussion examines whether a bulldozer is the most efficient way of using this geotechnical principle. Case 1 - Study eastern US: Contour coal stripping application The energy consumption for the Case 1 mining method (eastern US contour stripping operation) shows the D11 averaged 117 L (31 gal) of diesel fuel per scheduled hour, and produced 333.3 bank m3 (436 bank cu yd) per scheduled hour (0.351 L/m3). Assuming 1 L (0.26 gal) of diesel fuel contains 10.4 kW-hr of energy, the unit expenditure of fuel energy for Case 1 Study was 3.66 kWh/m3. Another way of shifting this material is by using an overburden slusher (OS), as shown in Fig. 1. The OS as shown in Fig. I. The OS is electrically powered and consists of a manned low wall winch (LW ), a remote controlled (radio telemetry) highwall winch (HW) and a hoe. The winches operate to pull the hoe back and forth across the pit. The hoe carries load in the forward direction ahead of a rear mounted blade and returns empty. A spreadsheet (Lotus 123) simulation package, BOSSIM, models the OS operation on a load by load basis over a wide range of pit configurations. The geometry shown in Fig. 2 of the paper was modeled using BOSSI M and the results are summarized in Table1. Table 1 shows a LW with 150 kW (200 hp) and a HW of 120 kW (160 hp) installed power, towing a 15-m3 (19-cu yd) hoe, would accomplish the Case 1 stripping task at about the same scheduled stripping rate (D11=333 m3/hr or 433 cu yd/ hour, OS=342 m3/hr or 447 cu yd/ hour). It was assumed the winches in this equipment have an electromechanical efficiency of 90%. This gives an average electrical energy expenditure rate of 151 kW-hr, and a unit energy expenditure level of 0.44 kWhr/m-3(0.57 cu yd/kWh)-an improvement of 8291%- over the D11 alternative. The energy comparison illustrates the importance of using more efficient electric power if possible, ahead of the internal combustion engine, and delivering power from a fixed ground position rather than through a moving track system. Another important energy observation is the comparative action of the dozer blade and the OS hoe. The former implement continuously digs and spills as it works the load forward. The OS hoe digs the load until full, the blade then lifts due to the contained load pressure and a shear plane forms under the mass, enabling it to slide forward in a force reduced - transporting mode. Economic comparison Table 2 operating cost per scheduled hour and unit cost comparison follows a format used in Tables 2 and 3 of Hrebar's paper and compares Case 1 Study with the OS alternative. Drill and blast costs are kept constant in both cases, although when larger OS units are considered, it is expected these costs will reduce because bigger hoe sizes will permit larger rocks to be transported efficiently.

Jan 1, 1995

By J. Mastoris

The determination of the surface area that may be impacted by underground mining is an important consideration in subsidence engineering. A number of parameters have been utilized to identify this influence area, most notably the angles of draw and break. This paper discusses the implications of selecting an appropriate "damage angle" for defining a potential damage area due to mining, within which surface structures may be impacted. Furthermore, the influence of both mining and geological factors (i.e., mining width, depth and overburden lithology) on this angle is examined using the Surface Deformation Prediction System (SDPS) software. Finally, recommendations are given for applying these concepts in subsidence control.

Jan 1, 1995

By J. Scheepers, P. Smith, G. (Yunfei) Qiao

High pressure acid leach (HPAL) and pressure oxidation (POx) or pressure leaching extraction processes occur in autoclave vessels operating at elevated temperature and pressure, acidic conditions with abrasive mineral slurries. The harsh process conditions require specialized severe service metal seated ball valves to support operation of the vessels. Over several decades thermally sprayed titanium dioxide (TiO2) and chrome oxide (Cr2O3) coatings have been applied to extend the service life of the ball valves and other high wear critical components. Variability in the coating application quality control and severe process conditions can result in spalling, coating failure and premature failure of the component resulting is decreased autoclave circuit availability. In 2012 MOGAS, together with BRENCO, initiated research and development for ML-381, metallurgically bonded coating. This paper includes the historical development of severe service ball valve coatings, success of the trials and increasing industry adoption of the ML-381 coating for ball valves and other critical autoclave circuit components.

Mar 2, 2022

By S. E. Younis

The mining industry is currently looking to better understand, anticipate, and be able to mitigate business and operational risks in order to deliver the rewards of risk taking, and to minimize the frequency and impact of risk on the downside. Assessing risk works from the premise that the identification and management of existing risks can be very challenging, especially when threats are not easy to detect, the likelihood of occurrence is difficult to gauge, and/or the consequences are uncertain. Some approach this as a ?check the box? task, even though fire and safety incidents continue to occur and investigations often find the hazard analyses did not properly identify the cause or consequence. You cannot engineer protective designs and safeguards for causes and consequences that have not been identified appropriately. For the mining industry, risk management is an important tool for making critical decisions and, in some cases, meeting regulatory requirements. Providing high-quality documentation that meets both regulatory and corporate requirements is critical for maintaining safe, uninterrupted mining operations. Risk management is a five-part process: 1. Identify the hazards and their causes, 2. Determine the hazard consequences, 3. Calculate the frequency of occurrence, 4. Quantify the risk associated with the system, process, or procedure, and 5. Provide feasible solutions for the risks

Jan 1, 2012

By Dr. -Ing. Rainer Alles

Introduction Belt conveyors usually run in a straight line. The correct alignment is a major criterion for reliable functioning and optimum running properties. Any misalignment of the conveyor, especially mistracking of the belt, can have many negative effects. As a consequence of this, damage can occur on the belt and conveyor, some material can he thrown off at the edges and serious running problems can arise. In the worst case the belt can come off its supporting structure so that operations are brought to a halt. The absolutely straight alignment of a belt conveyor is actually impossible so that on closer observation every belt conveyor contains more or less sharp curves. Whereas on non-movable conveyors the deviations from the straight can he kept within the range of practical measuring accuracy by careful installation, movable conveyors in surface mining or belt systems in difficult terrain often contain curves that are easy to see with the naked eye. Below ground, too, alignment cannot always achieved to a desirable extent or is changed by geological faults over the years. Despite these unwanted curves, most belt conveyors perform their function reliably. In view of the belt tension, the belt tends to take the easiest path. This in general is the shortest distance between the pulleys on which the belt is tensioned and bent. This means for example that for a curve radius of 10,000 m over a flight of 100 m the greatest deviation from the ideal line is as much as 12 cm. And a figure of this magnitude cannot normally he accepted. In such cases, use is made of guide devices to properly train the belt if it doesn't center itself anyway. If it's possible to control the belt position over such unwanted curves. it can also he expected that the belt tends to follow the desired curved path within certain limits. I'd now like to cite a few examples to illustrate the ways and means of guiding a belt conveyor in curves. Cost-effectiveness The advantages of belt conveyors, in particular for longer conveying distances and mass flows have been known and undisputed for some time. However, there are often obstacles standing in the way of the concept of straight routing. If a belt conveyor is to bypass elevations or existing buildings or to follow the seam of underground deposits or a predetermined path, then substantially tighter radii and longer curves are desirable or necessary.

Jan 1, 1993

By Michal Bukovansky

The Sahara Desert presents a serious obstacle to transportation route development in northwest Africa. Most highways and railroads are now limited to the coastal regions. A network of pioneer roads is the only connection between Algeria, Morocco, and Tunisia on the north, with Mali and Niger on the south. A feasibility study has recently been made for a paved highway between these countries. Climatic, geologic, physiographic and hydrologic conditions will significantly influence the construction of the road. In order to reduce costs, special construction methods will be required. An outline of these I conditions and methods is presented as an example of an engineering geological investigation in desert conditions.

Jan 1, 1970

By Silvia Misk, Cristina Araújo, João Felipe Costa, Roberto Rolo

Linear estimation methods are widely used for resource evaluation. Among the existing linear estimation methods, ordinary Kriging (OK) was accepted as the best estimator to determine the average ore grade of each block. However, OK is inadequate for modeling small blocks in relation to data spacing, resulting in over-smoothed models. In this study, the results of the recoverable resource from the short-term model are compared to estimated models generated by the traditional method, i.e., OK, and non-linear methods. The conclusion is that non-linear methods improve the accuracy and precision of the long-term model when compared to the model generated by OK.

Jun 25, 2023

By Alexandru Corneliu Stematiu, Catalin Popescu, Radu Sarghiuta

"The tunnel sector is excavated into a rock mass heavily affected by tectonics, defined as a regional fault. The rock around the tunnel support undertakes the non – elastic deformation and gradually detaches from the rest of the non affected rock mass, moving inside of the excavated area and tending to fill up the whole space. The initial solution of using stiff support consisting in double steel ribs I12 with circular shape in the upper part and straight vertical pillars in the lower part has proved to be inadequate. Based on the calculations of the subsidence phenomena and a mathematical model, the proposed alternative support was provided by special circular steel ribs – SG-23 –that allows a limited rib deformation (by relative slip between the arch segments) in order to mobilize the contact between the rock contour and the inner face of the rib - not only for the deformed rib but also for the neighboring ribs. 1. INTRODUCTION Hydropower development of Jiu river in Romania, in the narrow gorge sector includes two diversion HPP and a small hydro plant that provides the minimum required flow downstream: CHE Dumitra , CHE Bumbesti and MHC Livezeni (Table 1. Hydropower parameters).The Livezeni intake reservoir is provided by a gated dam located 1250 m downstream of merging point between Jiul de Vest river and Jiul de Est river. The dam is equipped with three radial gates with flap gates with a span of 12 m each and the height of (6 + 3) m. The longitudinal profile of Dumitra head and the location of the gallery zone that is the subject of the paper are presented in Figure 2. Longitudinal Profile – Dumitra Head."

Jan 1, 2016