Search Documents

By Jon “Ike” Isaacson, Frank Perrone, Eric Prantil

"Tunneling through an urban environment carries many inherent risks to the immediate local infrastructure and subsequently to the project stakeholders. On the CQ031 Contract of the East Side Access Project in Queens, New York, twin 22.5’ diameter Herrenknecht Slurry TBMs were mined within close proximity to many infrastructure assets, with cover of less than half a shield diameter at times. Multiple public bridges and critical railroad infrastructure including catenary poles and signal towers supporting the busiest rail interlocking in the United States required underpinning systems. The support program for these structures was refined over the course of the four tunnel drives. It is the intent of this paper to show how the interaction between the temporary structures, instrumentation monitoring plan, and risk assessment program melded to provide a system which the owner, contractor, and designer relied on as a tool to ensure the project success without impacting the public surroundings. PROJECT BACKGROUND The East Side Access (ESA) megaproject located in New York City, N.Y is a multi billion dollar program for the Metropolitan Transit Authority Capital Construction (MTACC) with the main goal of bringing the Long Island Railroad (LIRR) commuter rail to Grand Central Station located in the heart of Midtown Manhattan. When completed, the project will significantly reduce congestion both into and out of Penn Station, the current terminus of the LIRR. In order to accomplish this, multiple contracts of varying scope are required to operate simultaneously in both Queens, N.Y and Manhattan. In 2009, the CQ031 Queens Bored Tunnels Contract was awarded to the joint venture of Granite Construction Northeast, Traylor Bros. Inc., and Frontier Kemper (G.T.F). The main scope of this contract was to excavate four segmentally lined soft ground tunnels underneath the Sunnyside Rail Yard in Queens, New York. Additional scope of work included the construction of a tunnel approach structure, electrical substation, and multipurpose ventilation and egress facility."

Jan 1, 2016

By Raj K. Rajamani, M. K. Abd El-Rehman

The planetary mill is very much suited for the ultra-fine grinding of mineral fillers. Ultra-fine grinding here refers to grinding powders to a size range 5-1 0 rnicrons. Such powders enhance the quality of the final product. The operation of a specially built planetary mill is described. It is shown that a target size of 5 rnicrons can be reached in a few hours using the dual drive planetary mill. A centrifugal field of 37G is generated by the gyration arm of the mill. The design allows the desired setting of canister critical speed. The ultra-fine grinding of alumina, titanium dioxide, hematite, magnetite, kaolin and silicon carbide are described. Also, the continuous operation of the mill is shown.

Jan 1, 2003

By Otto Braach, Wolfgang Frietzsche, Erdogan Gürkan

The Westerschelde Tunnel is located in the south of the Netherlands and links the two parts of the Provinces of Zeeland, Zeeuws-Vlaanderen and Zuid-Beveland, which are separated by the Westerschelde. Road traf?c has up till now taken the detour via Belgium or crossed by ferry. This unsatisfactory transport link signifies major economic disadvantages above all for Zeeuws-Vlaanderen. The first fixed link for road traffic between the communities of Terneuzen and Borsele are to be created by means of the two 6.6 km long tunnel tubes down to 65 m below sea level.

Jan 1, 2003

By David Hurth

JOHN HAMRIC: Our next topic leader is David Huth, superintendent of sulfuric power generation, DAP, and shipping for IMC-Agrico, Nichols Plant, Mulberry, Florida. With a title like that it's no wonder he believes in empowerment. His topic today is "The Triumphs and Pitfalls of Using Empowerment Techniques." DAVID HUTH: Empowerment and its benefits are a desirable alternative to the traditional management structure. The difference between the two is the amount of decision- making authority and responsibility given to individuals by a supervisor. Just what is empowerment and how does it work? Empowerment is relinquishing to individuals the authority and responsibility to make daily decisions. Can everyone be empowered? What if they make a wrong decision? Will I empower myself out of a job? These are questions that all managers have when they hear the word empowerment. In today's fast-paced and high-pressure business environment, the old way of managing people must be replaced with a new approach. No longer can we, as managers, make all the decisions. The increased work loads due to downsizing, consolidation, and synergies have stretched us too thin. What about our employees? How can we motivate them into the high-performance teams that our companies are demanding? What possibly could satisfy both these issues? The solution to these problems can be solved with the power of employee empowerment. Employee empowerment will not only lessen the load on managers but will build teamwork, motivation, and pride into the employees who work for the managers who use it. American business was rudely awakened in the early 1980s when the Japanese companies not only caught up to American companies but literally flew by them. America was fat, dumb, and happy after World War II. Why wouldn't they be? They had all the factories. Everyone else had to rebuild. So for 40 years American business lounged in the limelight of very little true competition. But times change. Unfortunately, American business did not. Now the cry to perform in the new global economy has come down from the corporate boardrooms. Down through the ranks it has been felt. Guess who is supposed to make it work? But where are all those people who are going to make this rejuvenation and corporate renaissance possible? Many of them are gone-lost in downsizing, synergies, and rightsizings

Jan 1, 1998

By Gilbert A. Bonforte, Hugh P. Caspe, Tracy K. Lundin

The Narragansett Bay Commission (NBC) Combined Sewer Overflow Abatement Program is a major effort to address and mitigate discharges from combined sewer overflows in the Providence, Rhode Island area. The proposed system consists of three deep rock tunnel segments totaling 17.8 km (11.1 miles) in length that will provide 860,000 cu m (227 million gal) of storage at depths up to 99m (325 ft). This paper discusses 13.5 km (8.4 miles) of 6.64m (21.8 ft) finished diameter tunnel, four construction shafts, 19 dropshafts and one large diameter pump station shaft tapered from 1 5.2m (50 ft) at the surface to 27.4m (90 ft) at depth. All facilities are in preliminary design.

Jan 1, 1995

By A. B. Cecala

The US Bureau of Mines has designed and evaluated total mill ventilation systems (TMVS) at two mineral-processing operations. Both systems have proven proficient at cost-effectively reducing respirable dust levels throughout the mills. An 11.8-m3/sec (25,000-cfm) system installed at a clay-processing mill provided about 10 air changes per hour(acph). This system reduced respirable dust concentrations by about 40% throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 23.6 and 47.2 m3/sec(50,000 and 100,000 cfm) of ventilation to the mill building, corresponding to 17 and 34 acph. Average mill-wide respirable dust reductions were 36% and 64%, respectively. This work was done to determine general guidelines and design criteria for operations that may be interested in implementing TMVS. TMVS should be designed to draw clean make-up air in near the base of the mill. This air provides general purging and may clear some dust-laden areas throughout the mill structure. It is discharged at or near the top of the structure. Without the TMVS, dust can exit the building through open doors, windows, etc. and contaminate outside plant workers. This dust can also be recirculated back into the mill building causing additional contamination problems. TMVS is not a stand-alone system. It is a supplemental technique to assist other localized dust control systems (Mody et al.,1987).

Jan 1, 1995

By Eric Lutz

"Great effort has been expended for more than 40 years to improve the workplace safety and health of surface and underground miners across the United States. When looking at the past decade, withstanding the 2010, Upper Big Branch (UBB) disaster that took the lives of 29 miners, this effort has resulted in a generally decreasing trend from 57 fatalities (22 coal; 35 metal/non-metal) in 2005, to 45 (16 coal; 29 m/ nm) in 2014. Through August of this year, there have been 23 mining-related deaths (eight coal; 15 m/nm). These results reflect continued diligence and perseverance on the part of miners that stay true to our legacy; and demonstrate significant investments from mine-site leadership, mining corporations, and state and federal regulators. However, over the past five years there have been an average of 32 fatalities per year, with a low of 36 (2011 and 2012) to a high of 45 (2014). If we know that there will be somewhere between 30 and 50 mining related deaths next year, which of us will volunteer to be counted as one of the numbered? Clearly, we all agree that one fatality is too many; and as evidenced by changes following UBB, deaths in any sector are deaths reflective of all mining across all sectors.The impact of each miner death touches us all. Miner’s deaths are felt deeply by family and friends, most significantly the children; their communities in which they served, supported, and worshiped; and by society that has lost a hardworking, dependable contributor. Further, to take a slightly cynical, but realistic view, miner fatality events impact the financial vitality of mining and contracting companies and broadly diminish investor confidence. Just as important, these events significantly impact our communities and result in negative public perceptions, which ultimately drive regulatory policy and related compliance pressures. This resulting pressure forces operations to broadly address safety and health gaps in very specific ways (i.e., see U.S. Mine Safety and Health Administration (MSHA) regulations regarding lids for trash cans) minimizing a mine site’s opportunities for operational flexibility. To break this cycle that is the operational reality, mining companies are focusing tremendous efforts on fatality prevention and specifically on dedicated investment to prevent multiple fatality events."

Jan 1, 2015

Jan 1, 1998

By Frank F. Aplan

Introduction Heavy media separation (HMS), also called dense media or float¬sink separation, is one of the newer forms of gravity concentration. Though the concept can be traced to the last century, the process has enjoyed its major growth since 1940. Heavy liquid separation is a mutation. The heavy media process is used extensively to clean coal and for the concentration of a wide variety of ores such as those of iron, lead-zinc, chrome, manganese, tin, tungsten, fluorspar, magnesite, sylvite, garnet, diamonds, gravel, etc. It may be used where ever a significant density difference occurs between two minerals, and commercial separations are typically made in the range of 1.3 to 3.8 sp gr. The particle size treated ranges downward from 6-8 in. top size. Particles greater than about 1/16-in. (10 mesh) may be treated in a "static" bath, though for reasons of separation efficiency, + 1/2 -in- feed is usually preferred. For particles less than this size, separation in a heavy media cyclone is generally used. The flowsheet of a typical heavy media process, in this case one using a ferrous medium, is shown in Fig. I. In essence, the process consists of: (1) preparation of the feed usually by wet screening to remove undesired fines, (2) heavy medium separation, and (3) removal and recovery of the medium from the separated products. Many muta¬tions of the basic scheme are possible and numerous options are possi¬ble. HMS offers the following potential advantages:12 1) Ability to make sharp separations. 2) Ability to change the specific gravity of separation quickly to meet changing conditions. 3) Ability to remove products continuously. 4) Ability to treat a broad size range of products. 5) Ease of start-up and shutdown without loss of separating efficiency. 6) Relatively low medium cost and low media losses. 7) Low operating and maintenance costs. 8) High capacity with the use of relatively little floor space. 9) Relatively low capital investment per ton of capacity. The process may be used to produce a finished concentrate, two finished concentrates, or a concentrate and a middling of differing quality, or a preconcentrate by rejection of unwanted gangue. It is an ideal method for the reprocessing of coarse waste dumps. The greatest use for the process lies in coal cleaning and in the preconcentration of ores. The relatively inexpensive heavy media process may be used advantageously to reject large quantities of coarsely crushed gangue. When used in this way, the process will allow: (1) the use of lower cost but less selective mining methods with the "overbreak" material being removed at the front end of the concentrator or preparation plant; (2) a substantial reduction in the quantity of ore that must be finely ground for subsequent mineral liberation and separa¬tion. Since comminution is often the single most expensive step in beneficiation, it is desirable to eliminate as many essentially barren pieces of rock as possible before the grinding step, (3) a decrease in overall plant capital cost per ton of concentrate since the size of the plant from the dense medium step onward will be smaller. Several general references are available,12-18 though much of the technical data on the process is widely scattered in the general litera¬ture. Heavy Liquid Separation Organic Liquids Given sufficient settling time, it is possible to make a perfect separa¬tion between two particles of differing density by placing them in a liquid whose density is intermediate between the two. This means of achieving a perfect separation has proven to be elusive because of problems in feed preparation, particle settling rates, operational considerations, and economic constraints. There are a wide variety of heavy liquids that could be used, most of them halogenated hydrocarbons, and a few typical examples are given in Table 4. These liquids are most commonly used in ore dressing for the laboratory fractionation of ore particles on the basis of specific gravity. Laboratory Separations. Using liquids typified by those given in Table 4, separations are made to develop either the standard washability curves used to estimate the response of a given sample to gravity concentration or to prepare a partition curve to evaluate the effective¬ness of a given gravity separation process or piece of equipment. A typical washability curve is given in Fig. 2.19 Such curves are generated for raw coal, e.g., by treating either the whole or various size fractions of the sample in a series of heavy liquids and analyzing the various specific gravity fractions so produced. The procedure is relatively simple for coal samples because of the ready availability of a wide variety of relatively low cost heavy liquids in the density range 1.2¬-2.0. For ores the problem is much more complicated, because only a few high density liquids, all of rather high cost, are available. Parti¬tion curves are generated in the same manner by treating the separated products in the same liquids. Greater details on the procedures to be used in heavy liquid separa¬tions are to be found in the literature (for coal, Refs. 13, 14 and 19 and for ore, Refs. 20 and 21). For testing coal, calcium and zinc chloride solutions have been used extensively in the past, though today halogenated hydrocarbons (available under the trade name Certigrav) are the preferred media. The liquids shown in Table 4 may

Jan 1, 1985

By Richard Newcomb

Since the report of the 1972 Rapid Excavation Conference in the city of Chicago, speculation has continued concerning the estimates of tunneling demand. Little has been published that would persuade me to modify substantially the rather tentative estimates that originated with the National Academy of Sciences-National Academy of Engineering (NAS-NAE) study of 1968 which were recomputed by the United States in the survey of the Organization for Economic Cooperation and Development (OECD) in 1970. The OECD estimates, of course, hedged the really difficult question of forecasting civil construction tunneling demands. In the United States contribution, this was done by predicting both an upper and lower bound for important categories of demand. A discounting procedure was then applied to each of the major sectors of expenditures, permitting a forecast that reflected the current subjective assessment of how extensively and how likely cities were to adopt plans that required tunneling. This was done for water, utilities, transportation and other novel underground facilities. The purpose of this paper is a modest one. In it I wish to describe the efforts made since 1972 to generate more thoughtful and more robust estimates of urban sector demands, and to apply what has been learned to the most difficult category of predictions: those for urban mass transit systems. The estimates of the Underground Construction Research Council funded by the National Science Foundation have been described at an earlier panel of this Conference. The principal effort I am familiar with is that of

Jan 1, 1974

By Stephen P. E. Redmond

A 15 km water supply tunnel is being constructed in Buenos Aires, Argentinata expand the capacity of the existing system. Two 4.3 meter diameter Earth Pressure Balance (EPB) tunneling machines operating at times from the same shaft on a congested work site and advancing through sedimentary deposits underlying this wonderful city pose interesting challenges. As of January 1999approximately 50% of the tunnel has been excavated. Combined machine production rates of 1026 m/month have been achieved. Presentations made in prior proceedings can be referenced for details of the overall Project scope and for details of the tendering process. The purpose of this paper is to compliment those presentations by addressing now the execution of the work.

Jan 1, 1999

By R. R. Klimpel

The process of flotation is an extremely important solids separation technique employed in a wide variety of industrial process applications. Froth flotation is practiced in the coal industry to recover fines produced during the mining and cleaning of coal. A recent review article by Aplan (1) covers the processing variables encountered in the flotation of coal and the variety of chemicals and operating conditions which affect recovery. Numerous engineering and scientific studies have been performed with the goal of providing semifundamental laws of flotation behavior for improved screening of flotation chemicals, better equipment scale-up factors, etc. Often the results of such work are expressed in the form of mathematical models (e.g. 2, 3, 4, 5, 6) which are potentially useful for evaluating (simulating) on paper such alternatives as possibles process operating or configuration changes, the effects of ore and reagent changes, etc. It appears to be commonly accepted that a complete scientific/engineering characterization of flotation is immensely complicated and not sufficiently developed at the present to accurately predict (or understand) many important industrial facets of flotation. Thus, one is often reduced to detailed experimental characterization in both the laboratory and plant in order to fully evaluate flotation changes or alternatives. It is the purpose of this paper to describe a method of batch laboratory data characterization that is useful in evaluating flotation chemical reagents including froth flotation of coal. The approach consists of running a series of time-recovery curves in a batch float cell followed by the computer curve fitting of this data to a series of mathematical models based on semi-physical reasoning. The unknowns or parameters of these models are then optimally chosen so as to best fit the experimental data. It has been found in both coal and mineral systems that changes in reagent type, concentration, system pH, grind, etc. cause very consistent and logical changes to

Jan 1, 1979

By Bo-Hyun Kim, Mark K. Larson

"Researchers at the National Institute for Occupational Safety and Health (NIOSH) have advocated the use of instrumentation in underground mine ground control studies to aid in understanding failure mechanisms and to calibrate numerical models. The purpose of these efforts is to reduce accidents and fatalities in underground mines resulting from inadequate design of mining layout or supports. A recent examination of some results of stress change measurement raised some questions about the validity of elastic solutions in ground, such as coal. Particularly under deep cover as is prevalent in the western United States, the coal around a borehole would likely have yielded so that post-yield behavior would govern the response of the instrument.A numerical experiment was conducted by NIOSH researchers using the FLAC software (Itasca Consulting Group, 2016) to investigate the response of the borehole pressure cell (BPC) and the biaxial stressmeter to varying degrees of plastic behavior. The pre-encapsulated BPC cell pressure exhibits increasing departure from the elastic case with decreasing post-peak-strength slope of the stress-strain curve. On the other hand, because the BSM usually provides much more confinement to the surrounding rock than does the BPC, the measurements obtained from the BSM do not depart significantly from the changes in secondary principal stresses and directions as calculated by the elastic solution.INTRODUCTIONSeveral years ago, Larson et al. (2000) described several instruments that NIOSH had used in underground field studies and how to monitor them with dataloggers. This information is still relevant because of the need to understand how excavation affects the stability of mines and thus, the safety of mining personnel. One class of instruments described in that paper includes those instruments that measure change in rock stress. Although several such instruments might be used to measure stress change, the focus of this paper is on two instruments with which NIOSH has had more recent experience—the borehole pressure cell (BPC) (Geokon, 2018a; RST Instruments, 2018) and the biaxial stressmeter (BSM) (Geokon, 2018b). Other instruments, such as the CSIRO hollow inclusion stress cell (HICell) (Earth Sciences, 2019; Worotnicki and Walton, 1976) may be included in future studies.Early studies in the development of the BPC were those of Panek and Stock (USBM, 1964), Sellers (1970), Lu (1984), and Babcock (1986). Babcock’s work is particularly useful, but his setting and testing range was far below what we experienced in the NIOSH study, and it was Babcock’s data reduction scheme from his laboratory experiments that was used to calculate stress change in the NIOSH study (NIOSH, 2019a)."

Jan 1, 2019

By F. B. Henderson, D. Bird, P. L. Hauff, E. C. Prosh

A National Aeronautics and Space Administration (NASA)-funded project (NASA Grant #NAG13-02026) is underway to determine the ability of hyperspectral remote sensing to map mineralogy that affects water quality within a watershed and to identify the relative contributions of natural and anthropogenic sources to that drainage. Natural sources, particularly areas of pyritic hydrothermal alteration, have been found by the Colorado Geological Survey to be a significant source, sometimes the only source, for acidity and/or metals in a number of areas of Colorado (Neubert, 2000). This situation undoubtedly occurs in many places in the Western United States and elsewhere where metallic mineralization occurs. Anthropogenic sources arise from mining and other human activities that increase the exposure of acid-generating materials to weathering processes, thereby increasing acidity and metal loading to drainages where that activity is occurring or has occurred. This project is attempting to determine if these sources can be differentiated through mineralogical analysis, in conjunction with surface water chemistry that controls the precipitated minerals, of the impacted drainages by remote sensing techniques.

Jan 1, 2003

By Alfred Weiss, Andrew E. Nevin, Thomas J. Neil, O&apos

As Edward E. Runyan, 1983 AIME President, in an interview excerpt in ME, June, p. 607, stated, "...the AIME Transition Committee has recom¬mended to the AIME Board that each Constituent Society be allowed the option of separate incorporation, whereby each could become its own separate legal entity." Background The American Institute of Mining Engineers (AIME) was formed in 1871 by 22 engineers in Wilkes-Barre, PA. Although originally a mining organization, it became a home for metallurgists, iron and steel industry people, and for the individuals in the expanding petroleum engineering profession. There are now four Constituent Societies: Society of Mining Engineers, located in Littleton, CO, 29,000 members; Society of Petroleum Engineers, located in Dallas, TX, 47,500 members; The Metallurgical Society, located in Warrendale, PA, 10,000 members; and Iron and Steel Society, located in Warrendale, PA, 6,500 members. Each of the four groups has grown and continues to serve the specific and/or diverse needs of its membership. As the needs and requirements of their industries and professions change, each of the Societies has perceived and initiated programs that serve their constituency rather than AIME as a whole. Therefore, each Society has recognized an increasing need for autonomy to better augment their own programs. An AIME Ad Hoc Transition Committee, with Robert Merrill, AIME Past President, as chairman, made a number of recommendations pertaining to AIME operations that were approved in October 1982 by the AIME Board of Directors. One of the recommendations was to endorse separate incorporation of the Constituent Societies on an individual-society-option basis. The AIME Board commissioned a task force of Constituent Society representatives to develop specific revisions to the AIME Certificate of Incorporation and the AIME Constitution and Bylaws. This was done to allow separate incorporation and to reflect the decentralized structure of the Institute. The SME-AIME Board of Directors subsequently approved the recommendation of SME Working Party #69 that SME pursue separate incorporation. Meanwhile, Working Party #69 continues to work with the other Constituent Societies and with the AIME Task Force on Reorganization to determine the form and substance of the separate incorporation. Why Incorporate? George Webster in The Law of Associations quoted Chief Justice Marshall's (1819) definition of corporation as: "A corporation is an artificial being, invisible, intangible, and existing only in contemplation of law. Being the mere creature of law, it possesses only those properties which the charter of its creation confers upon it, either expressly or as incidental to its very existence. These are such as are supposed best calculated to effect the object for which it was created." SME-AIME attorneys, Davis, Graham & Stubbs, have pointed out that the status of an organization operating as an unincorporated association is always unclear. At present, SME-AIME administers assets of almost $3.5 million (mainly property and inventory) but technical ownership and ability to enter into contractual relationships resides with AIME. However, the operation appears to outsiders (particularly those with whom SME-AIME does business) to be an independent operation which would be expected to be a legal entity in its own right. Advantages of Incorporation Liability. Because of legal ownership by AIME of all assets of the Constituent Societies, those assets are subject to the claims of any of the creditors of AIME or any of its constituent parts (i.e., the other societies). Liabilities can be those usually encountered in business but also encompass special risks, which could develop if there were a careless and erroneous publication of material that might be used in practice or if standards are improperly established. The recent US Supreme Court decision in American Society of Mechanical Engineers, Inc.,

Jan 10, 1983

The deformation, failure, and filling characteristics of a caving roof in the initial and normal mining stages of a pitching oblique longwall mining area are analyzed using large-scale threedimensional physical-similitude experiments and numerical calculations to study the characteristics of roof fracture and migration in a steeply dipping seam. The results show that the roof fracture development has evident sequential and spatial characteristics. Among them, immediate roof breaking in different parts of the mining area shows difference in time and space. The failure sequence of the immediate roof in different areas changes with the mining; unique regional stability evolution characteristics are observed in the suspended immediate roof simultaneously, resulting in its significant regional stability on the goaf filling.

Jan 7, 2020

By S. C. Sun

[There are significant quantities of anthracite silt deposits in Pennsylvania, known as 'liver silts" (l,2). These contain from 20 to 55 per cent of non-combustible materials, the major portion of these impurities being clay slimes. Both the anthracite coal and impurities are mostly of extremely fine particle size. The utilization of these raw silts in power-plants faces such serious problems as, handling difficulties causing plug-up in equipment, disposal of enormous ash-residue, and corrosion. These problems may be solved by upgrading the raw silt with a cleaning process, which will be capable of removing most of the clay slimes and electrolytes.]

Jan 1, 1964

By D. Malhotra

Climax byproduct-plant tailing assayed 0.019 percent WO3. Pilot-plant and laboratory tests were performed to investigate the possibility of recovering additional tungsten values from the byproduct-plant tailing. The paper discusses the methodology used in the study and the results of this investigation.

Jan 1, 1985

By P. E. Sarquis, R. Lenzo

The concentration of barite by gravity separation generates substantial quantities of fine particle wastes, and it is estimated that =40% of the contained barite is lost to these waste streams. In this study, froth flotation was examined as a potential method for the recovery of fine-barite particles. The study included the use of kinetic equations to estimate the variables affecting flotation, batch-scale rougher flotation tests to study the flotation variables and an examination of alternatives for the cleaning of the rougher concentrate. Results indicated that a concentrate grade of 96.5% could be achieved with a recovery of 77.5%. Although barite flotation from industrial wastes is more difficult than direct barite flotation, the process has considerable economic potential.

Jan 1, 1996

By John S. Newton

Modern high capacity underground mining machinery is a complex of mechanical, electrical and hydraulic components which have greatly increased capability over similar components of mining machinery of ten and. even five years ago. Looking into the future I feel certain in stating that there will be changes equally great in the coming five and ten year periods. With this premise in mind, I should like to bring to your attention some of the things that do and will have a continued major impact on the industry, particularly as they relate to the maintenance and operation of these machines of increasing capability. In underground mining today, nearly every individual plays a key role. A machine operator's importance in his work is comparable with that of the pilot of an airplane, a railroad engineman, a bus driver, a skilled machinist, a bulldozer operator and many others whose assignment is one of doing, by himself, with his hands and his brains all that the specially designed machine has been created to do. These machine operators are supported by a staff of skilled engineers, maintenance personnel, supervision, etc., but objectives are realized only when the operator maintains his schedule. What is being done and what can be done to make it easier for the operator to maintain his schedule which, as with the airplane, is constantly being improved? This question can be answered best, perhaps, by dividing the subject into four general categories - (A) Power Supply. (B) Control and Protective Devices. (C) Hydraulic Component Design. (D) Mechanical Design.

Jan 1, 1962