Search Documents

By William M. Kester

Finely sized Upper Freeport coals are beneficiated to reduce ash and sulfur using high-intensity magnetic separation to process both (1) raw, untreated coal as well as (2) raw coal which was pre-treated thermally with steam and air. Substantial, sulfur and ash reduction can be obtained using both approaches to magnetic beneficiation of coal fines, but evidence indicates that pre-treatment which would constitute a costly supplementary step is technically inferior to the direct beneficiation of raw, untreated coal. These bench-scale studies demonstrate that if high-intensity,; high capacity, dry, magnetic beneficiation equipment can be developed and' installed at coal burning power plants or at appropriate points in coal preparation plants substantial quantities of sulfur may be removable from coal after pulverization as a means' to reduce air pollution.

Jan 1, 1965

By Z. Xu, Z. Li

Colloidal interactions play a critical role in mineral processing, including grinding, physical separation (particularly flotation), dewatering, and tailings management. Despite great energy input in comminution to liberate valuables from gangues, heterocoagulation between valuables and gangues would prevent the separation of valuables from gangues. On the other hand, selective coagulation/flocculation to increase the size of desired fine particles could enhance physical separation and dewatering, while dispersion is needed for fine grinding. To control the state of colloidal dispersions by creating favorable conditions, it is of paramount importance to study colloidal interactions in a relevant system and understand underlying mechanisms. This review summarizes recent advances in developing the-state-of-the-art techniques and novel methods of measuring colloidal forces, including atomic force microscope, surface force apparatus, zeta potential distribution measurement, quartz crystal microbalance with dissipation, and our recently developed integrated dynamic force apparatus. The basic principle of each technique was introduced first, followed by a summary of critical information derived for the relevant mineral processing systems. Finally, the pros and cons of each technique were discussed to emphasize the use of complementary techniques that assist in solving fundamental problems in mineral processing.

By H. J. Chen

In recent years, it has been recognized that the high horizontal stress is an important factor that contributes to a cutter roof. When the immediate roof is thinly bedded, the presence of a high horizontal stress may first cause failure on the bedding planes or weak planes, and then a cutter roof develops as the individual stratum crushes and buckles progressively layer by layer. In this study, the stress distributions in the bedding planes of the immediate roof are analyzed for an entry-pillar system in the multiple longwall panels by using the finite element method. Then the roof failure is analyzed based on the rock failure criterion and the stress distributions.

Jan 1, 1998

By W. J. Wolfe

Using a combined fire assay-atomic absorption method, gold determinations with a minimum detection limit of 5 ppb were made on 345 samples of Early Precambrian felsic plutonic rocks collected 2 2 from intrusions ranging in size from 4 km to 88 km and in composition from syenite to granodiorite. Gold levels in unmineralized stocks are consistently below the 5 ppb detection limit of the analytical method used. In contrast, analyses of samples from stocks containing gold mines within their borders and in nearby metavolcanic-metasedimentary host rocks show a strongly skewed trace element gold population with a substantial percentage of gold values exceeding 5 ppb and ranging as high as 320 ppb. The data indicate that (1) ore-stage hydrothermal metasomatism has produced widespread Au enrichment in Precambrian intrusions that host epigenetic vein-type gold deposits, and (2) geochemical Au analysis of samples collected from 30 to 50 randomly distributed sites can be used to estimate the gold exploration potential of stock-sized bodies and to outline internal patterns of Au variation which may be useful in directing exploration to particular contacts or portions of a stock. The results do not conclusively indicate unusually high Au content in primary unaltered igneous rocks.

Jan 1, 1975

By R. Sharon

Barrick Goldstrike Mines, Inc. Betze-Post open pit operations, located in northeastern Nevada, have experienced slope instability attributed to the presence of generally weak rock mass conditions, local adverse structural geology and perched groundwater. Ground movements are monitored with acombination of optical survey, extensometers, inclinometers, and time domain reflectometry (TDR).The slope monitoring system at Goldstrike includes two robotics theodolites, which provide real-time coverage for all highwall areas. Survey instruments are housed in specially designed climate controlled shelters in locations where all slopes can be observed. A “remote” computer housed with each theodolite collects data. The “base” computer, located in the mine offices, is used to access data from the remote computers via radio modem.

Jan 1, 2000

By David Runnels

In September 1970, the Quebec Cartier Mining Company, started development of the Mount; Fright iron ore mine. The estimated ore reserve is in excess of 1,000,000,000 long tons with an average grade of 31.5% Fe. The run of mine ore is crushed, ground and concentrated to a product having 66% Fe and 5% silica at an annual concentrate production rate of 18.4 million long tons. The daily production rate of over 50,000 long tons of concentrate necessitates a daily mine output of approximately 250,000 long tons of material of which 50% is waste. The mine is located in the Province of Quebec, close to the Labrador border approximately 600 miles north-east of Montreal. The development of the mine necessitated the construction of an all electric one thousand housing unit townsite along with associated services such as a shopping center, swimming pool, arena, school, etc... A one-hundred mile long, 315 K.V. Dower line was built between the mine site and the Hydro-Quebec 735 K.V. existing power line between Churchill Falls and the Montreal area. The construction near the mine of a beneficiation plant was necessary to upgrade the 31.5% iron ore to a marketable product of 66% iron.

Jan 1, 1977

By M. Li, J. D. Miller

During the past decade, considerable effort has been made to develop improved flotation strategies for the sedimentary phosphate resources from Florida, particularly the dolomitic phosphate resources. New flotation equipment and alternate flotation strategies have been evaluated. These developments are reviewed for both traditional siliceous resources and future dolomitic resources. Most process strategies involve variation in the reagent sequence and/or the use of depressants/dispersants. Further research and development efforts in flotation technology are needed to increase flotation plant capacity by elimination of the conventional double float process, to improve the recovery of coarse phosphate, and to achieve the desired selectivity with respect to carbonate minerals, particularly dolomite.

Jan 1, 2000

In some 35 years in the explosive and construction industries, we have probably seen the extremes in drilling and blasting practices. All of you know that it is difficult if not impossible, to separate those two operations, particularly when we are searching for an optimum. Early in my career while doing engineering survey work for a major cross country pipeline construction company, we witnessed some of the wildest blasts imaginable, and they were wild for two reasons. Both the drill hole diameter and the drill pattern were such that when loaded with explosives, the factor in terms of pounds/cu. yd. was extremely high. On the other hand, in 1982 we were in an underground coal mine where just one hole was used to prepare a 20-ft. (6m) wide face. In this coal mine, they brought down 7 yd3 (5.35m3) of coal with just 1 lb. (.454 kg) of explosive. On a pipeline job, the factor may only be .1 yd3 per lb. of explosives. Open pit operations in the same geographical area may have almost the same type of rock, but similarities could end there. The several operators over the years will have installed different size-crushing equipment or variances will exist in other facets such as drilling, excavating, and haulage units. That tells us that if we have 6 operations in that common area, we are faced with a fact that there is an optimum drilling and blasting pattern for each of those six. We start at that point. We will note from Figure No. 2 the simple equations for determining either cu. yds. or tons. For a rock heavier than limestone, it may require only 10 to 11 cu. ft. (.31m3) for 1 ton (.91 metric ton) of rock in place.

Jan 1, 1986

By Bernard L. Merlo

INTRODUCTION Modern mine management is constantly striving to develop improved mining methods which will not only increase productivity, but will also provide a safer work environment and make the most efficient use of our natural resources. Progress can be seen in this area by tracing mining methods through history. Work that was originally done with hand tools progressed with the age of mechanization to conventional mining, matured to continuous and longwall mining, and the advent of short¬wall mining, a combination of continuous and longwall, has recently been seen. This new method of shortwall mining provides a promising method for safe and ex¬pedient coal extraction. This study focuses upon the planning, design de¬velopment, and operation of the first producing short¬wall unit in the US which was operated in the Pittsburgh coal seam in northern West Virginia. MINE DESCRIPTION The mine is located in northern West Virginia at Grant Town in the heart of the high volatile Pittsburgh coal seam. Originally opened in 1901, the mine has be¬come one of the largest in the US, encompassing an area of approximately 103.6 sq km (40 sq miles). The seam being mined was the high volatile Pittsburgh seam which ranged in thickness from 1.8 to 2.96 m (6 to 91/2 ft). Three types of mining methods were employed: con¬tinuous mining, longwalling, and shortwalling, with each type accounting for 50%, 30%, and 20% of total pro¬duction, respectively. A total of 630 contract and super¬visory personnel were employed to produce the mine's designed annual tonnage of 1.8 Mt (2 million st). There were ten producing sections, eight continuous miners, one longwall, and one shortwall, operating a total of 22 unit shifts per day. Eight shafts, varying in depth from 80.2 to 194.2 m (263 to 637 ft) provided entrance to the Pittsburgh coal seam. These shafts were used for ventilation, portaling, coal hoisting, supply, and emergency escape hoisting. Ventilation was achieved by means of three exhaust fans which provided 707.9 m3/s (1.5 million cfm) of air to the mine and removed approximately 141 584 m3 (5 mil¬lion cu ft) of methane per 24 hr period. The room-and-pillar method was used for secondary recovery with designed barrier blocks between panels of 61 m (200 ft) in width. A double row of blocks was left around each gob area to provide efficient bleeder action

Jan 1, 1982

By Stephen Hoffman

The Environmental Protection Agency (EPA) is investigating approaches to control non-coal mining wastes. In May 1988, the EPA's Office of Solid Waste (OSW) released a document that outlined an approach to manage non-coal mining wastes and materials. This document was called Strawman I. It was a staff-level approach designed to aid the continued participation of interested parties and to enhance EPA's understanding of mining waste issues. EPA has been working with states, public interest groups and the mining industry to gather information and to solicit input on waste management approaches. The involvement of the states in the Strawman process has been coordinated by the Mine Waste Task Force of the Western Governors' Association and the Interstate Mining Compact Commission. Involvement of public interest groups has been coordinated through Colorado Trout Unlimited. And the participation of the mining industry has been managed principally by the American Mining Congress. In May 1990, EPA released Strawman II. It was based on comments submitted to the EPA on Strawman I and on information given to the EPA by interested parties since 1988. Strawman II is again a staff-level approach to protect human health and the environment from wastes and other materials associated with non-coal mining. In September 1990, meetings were held with public interest groups and the mining industry to discuss their comments on Strawman II. By early 1991, the EPA expects to make a decision on how to proceed with program development.

Jan 1, 1990

By E. L. Fidler, T. E. Finch

Wayne Anderson Regarding the technical paper by Thomas E. Finch and Edward L. Fidler, "Recovery of Stray (Thin) Seams in Western Coal Mining." I would like to comment on this subject. In western Canada, most strip mines encounter thin seam coal or rider seams. Although the paper addresses the problems and costs associated with the recovery of this coal, it does not take into account what the savings are. Without looking at the savings, the "Total Objective" is of course not clear. I feel that in a stripping operation the mine can spend per ton (of the thin seam) up to their dragline stripping costs per ton to recover a rider seam or thin seam. The reasoning behind this is simply that this is the price the mine will have to pay to expose an equivalent amount of coal without the recovery of these thin seams. If the mine can recover a rider seam or thin seam for less than the dragline operating costs per ton, a savings will be realized. By recovering a thin seam or rider seam, the life of an ore body is extended by that amount of coal not thrown away. In addition, the cost of land acquisition, associated permits, capital, and reclamation will be reduced as more coal is delivered for a given area. When the above points are considered, the recovery of these thin seams can be very profitable and indeed worth recovering.

Jan 11, 1982

By Jan Wolski

Increasing interest in the Bucket Wheel Excavator (BWE) technology calls for a universally understandable definition of suitable performance factors which would reflect the unique features of this technology. The importance of properly designed and calculated performance factors for the BWE systems cannot be overemphasised. They are used by all levels of management in any mining organization for a wide variety of purposes, in particular for budgeting, for selecting new equipment, for monitoring current equipment and for comparison with other operations.

Jan 1, 1984

By Luisa Alfieri, Giorgio Fantauzzi, Sergio Notarianni, Spencer Cavagnet, Alessandro Damiani

"The new tunnels of the Copenhagen ""Cityringen"" will be excavated, at Kongens Nytorv square, crossing over the existing M1 and M2 metro lines. After the crossing, the tunnels will underpass the historical building of the Magasin du Nord and adjacent masonry buildings, with a minimum tunnel cover of about 4.5 m. The tunnels have an internal diameter of 4.9m and are being excavated through earth pressure balanced Tunnel Boring Machines in mixed face.The Magasin du Nord estate is characterized by a very complex structure, with different blocks built in different times. An assessment of the condition of the building and its sensitivity to tunnellinginduced ground movements has been conducted through a fully coupled soil-structure interaction analysis; based on the results of this analysis, mitigation measures have been designed.INTRODUCTIONThe Copenhagen Metro Cityringen is expected to be running in July 2019 and will consist of two single tracks in a twin tunnels, each approximately 16 km in length, for transporting up to 243,000 passengers on an average work day. The Cityringen includes 17 underground stations with island platforms, 4 crossover facilities and 3 construction and ventilation shafts. The tunnels is being excavated using earth pressure balanced Tunnel Boring Machines and have an internal diameter of 4.90 m.The intersection with the existing M1 and M2 metro-line will take place at Kongens Nytorv and at Frederiksberg. According to the design alignment, in Kongens Nytorv the new tunnels will pass over the existing M1 and M2 ones; as a result of this, the tunnels will underpass the historical building of the Magasin du Nord and the adjacent masonry building hosting a Mc Donald’s with a minimum cover of about 4.5m.In the framework of Risk Assessment for sensitive buildings, the effects of tunneling-induced ground movements on the Estates ØS0437 (McDonald’s building), ØS0428 (Magasin du Nord) and ØS0004 (Hviids Vinstue) were evaluated. To achieve this goal a fully coupled soil-structure interaction has been considered and the entire excavation process has been reproduced in a 3D model where the abovementioned buildings have been modeled. In this way, a risk assessment analysis was performed evaluating directly the effects of the excavation in terms of settlements and variations of the internal forces as far as the excavation process proceeds. In figure 1, a picture of the construction of Kongens Nytorv station, with Magasin du Nord and Mc Donald’s building on the background, is presented."

Jan 1, 2016

By Arthur B. Cummins

It is appropriate to discuss diatomite at an AIME meeting in San Francisco. California has led the nation, and the world, in the production of diatomite products for more than 40 years. It appears that our State will maintain this position for a long time to come. Diatomite today ranks high in the list of California mineral commodities, with a total value since 1889 well in excess of $100 million. California's production has more than doubled since 1942. In 1959, the value of diatomite production in California is exceeded only by the following industrial mineral materials-borates, stone, sand and gravel and cement20,28. Also, not unimportant is the production of diatomite in each of our other Pacific Coast States, including Nevada. First, let us define diatomite. It is a sedimentary siliceous rock of organic origin, which consists mainly of the fossilized remains of diatoms. Diatoms are microscopic aquatic plants which have the capacity of precipitating silica bio-chemically so as to form a part of their organized structure. In the economic sense, we are not concerned with the numerous types of sedimentary materials which contain minor amounts of diatom residues, or with impure or highly indurated siliceous materials, which may have been formed from diatomite2. Diatomite (synonyms--diatomaceous earth, kieselgurO is a term generally restricted to material of such qualities as to be suitable for commercial uses. Diatomaceous silica is a designation which is best used to distinguish the basic component of diatomite, that is, the substance of the silica shell itself, and which is the major' constituent of beneficiated diatomite or processed diatomaceous products.

Jan 1, 1959

By A. C. Nixon, A. D. S. Gillies, Hsin Wei Wu

Ventilation and refrigeration strategies for the 3000/3500 orebodies, Mount Isa Mines, Australia were reviewed. The orebodies lie between 1,200 and 1,800 m below surface and are characterised by steep geothermal gradients, intensively mechanised stoping methods and high ambient air temperatures in summer. Providing acceptable working conditions under these situations is difficult and costly. The ventilation air quantity required in the 3000/3500 orebodies exceeds 550 m3/s when the production rate is greater than 2.5 million tonnes per year. The maximum quantity that can be supplied and exhausted using the existing intake and return ventilation system is estimated at about 630 m3/s. For production rates greater than 3 million tonnes per year, either new intake and return airways will need to be developed or innovative approaches such as controlled partial recirculation used. A description is given of technical and economic investigations conducted at Mount Isa into controlled partial recirculation. During these investigations, a major field trial of a controlled partial recirculation system was undertaken with results indicating that an acceptable working environment can be achieved practically and economically utilising this approach. The cost involved in controlled partial recirculation for supplying the required ventilation quantity when the production of 3000/3500 orebodies exceeds 3 million tonnes per year is examined. A cost comparison between recirculation and other conventional alternatives such as new surface shaft or underground booster fans is included. The results indicate that the option of a new surface shaft will incur a high initial capital cost and moderate annual operating costs. The alternative of underground booster fans will necessitate a moderate capital cost and very high operating costs. Controlled partial recirculation, in this case, offers both the lowest capital and operating costs of the three options evaluated.

Jan 1, 1995

By James W. Furlow

A recent attempt by a major mining company to mine phosphate in Chatham County, Georgia, resulted in a study by the Georgia Department of Mines, Mining and Geology which was intended to evaluate the deposit as well as potential hazards to the major fresh-water aquifer of the area. The study found that the confining layer above the fresh-water artesian aquifer is sufficiently thick and impermeable to allow removal of the phosphate ore zone without significant salt water infiltration into the aquifer. Therefore, phosphate mining under proper supervision will not adversely affect the quality of water used by the city of Savannah nearby. Volumetric studies show that there is a minimum of 4,800,000,000 cubic yards of phosphate matrix containing an average of 22.5% BPL. At an approximate weight of 1.5 tons per cubic yard and a concentration of 22.5% BPL, there are about 1.6 billion tons of 100% BPL concentrate present. At a conservative factor of 50% at least 800,000,000 tons of 100% BPL concentrate could be recovered for market sale. In addition to the area discussed, evidence indicates that the phosphate horizon-may extend continuously out to sea for at least ten miles, and probably beyond.

Jan 1, 1972

By Earl Gardiner, Michael Grenier, Stephen Hardcastle, John Vergunst

A prototype, self-contained mine refuge station air supply sys- tem was tested in an underground metal mine to verify it's ability to keep oxygen and catbon dioxide levels at acceptable concentrations in an emergency situation. In this test, 25 volunteers were assembled and sealed in a functional underground refuge station for a period of 24 hours, without the benefit of the standard com- pressed air supply. The prototype system was designed to: 1) operate on a self-contained power supply for a period of at least 27 hours; 2) supply oxygen at a metered rate; and 3) remove car- bon dioxide by re-circulating refuge station air through soda lime scrubbing beds. During the test period, the catbon dioxide concentration remained at an average of 2500ppm and oxygen concentration stayed between 20.2% and 20.6%. The volunteers found the prototype easy to use and seemed confident in its ability to provide a safe atmosphere. The test showed that this technology could become part of an underground mine's refuge station emergency equipment.

Jan 1, 1997

By Janusz S. Laskowski

Studies carried out over the last 10 years reveal that precipitating particles which may appear in alkaline solutions of long-chain amines and in acidic solutions of fatty acids exhibit clear isoelectric points around pH 10.6-1 1 for dodecylamine and around pH 2.5-3 for fatty acids. These colloidal species can accumulate at solid/liquid and liquid/gas interfaces and affect flotation. While the precipitate in solutions of fatty acids apparently can chemically interact with the mineral surfaces and is flotation-active if sufficiently long conditioning time is available, the cationic flotation of quartz in alkaline solutions is depressed by the colloidal precipitate. The experimental data available in literature on the adsorption, electrokinetic, contact angle and surface forces measurements in the solutions of the weak electrolyte collectors are analyzed and the role played by the precipitate is discussed. It is shown that these concepts allow for an explanation of the selective flotation of sylvite from halite with long-chain amines in potash ore flotation.

Jan 1, 1999

By R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (K088) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron-and steel making and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By I. Papadopoulos

Nowadays, geophysical prospecting is implemented in order to resolve a diversity of geological, hydrogeological and geotechnical problems. Though plenty of applications and a lot of research have been conducted in the country-side, only a few have been reported in the literature concerning urban areas, mainly due to high levels of noise present that aggravate most of the geophysical methods (e.g. electromagnetic, seismic, gravity etc.) or due to spatial limitations that hinder normal method implementation (e.g. electrical). Among all geophysical methods, electrical tomography proves to be the most rapid and urban noise insusceptible technique. This work presents a case study in the urban area of Hania (Crete I., Greece), where Electrical Resistivity Tomographies (ERTs) have been carried out for the detection and identification of possible buried ancient ruins or other manmade structures, prior the foundation of a building. Nineteen profiles were surveyed in a 20x40m grid using dipole-dipole configuration. The results indicate two areas of interest, that are interpreted as probable old wells, in the context of the existence, in former times and in the same area, of an olive oil plant. In the vicinity, near surface ancient ruins have been disclosed, but no such evidence provided this survey, for the particular area under study and the prospected depth. The collected ERT-data were processed by applying advanced algorithms in order to obtain a 3D-model of the study area that depicts more clearly and accurately the interesting subsurface structures.

Jan 1, 2005