Search Documents

By M. G. Ayat, B. C. Scott

H. P. Ferri I refer to the article "Degradation Process in Coal Slurry Pipelines" by M.G. Ayat and B.C. Scott in the September 1988 issue of Mining Engineering. I would like to congratulate Dr. Ayat and his colleague on a very interesting and valuable piece of work. This article is an excellent one, describing a real phenomenon that has been ignored for so long. I do, however, have an objection. The article fails to address the degradation process when coal is processed or transported in other ways than slurry form, particularly those employed in this work. Could, for example, screening (wet or dry) have contributed to the extent of degradation? Perhaps scanning electron micrographs of the samples examined and after screening would have helped to clarify this. I would like to point out that degradation is also observed in pneumatic conveying systems, mechanical conveying, and other means of transportations employed by the mineral industry. Reply by M. G. Ayat We gratefully acknowledge Dr. Fern's comments on the subject paper. As he so rightly points out, the degradation process is a real problem, not only in coal slurry pipelines, but also in many handling and processing equipment employed by the coal and mineral industry. Scanning Electron Microscopic examination of samples may offer very little information about the extent of degradation for several reasons. One is that preparing a representative sample that has undergone degradation will be extremely difficult if not impossible. This problem is exacerbated by the fact that SEM requires only very small amounts of material for testing. Secondly, there is a sample preparation step involved in the SEM examination and, as such, it would be very difficult to associate the extent of degradation to either sample preparation or handling and processing operations. Finally, it is probably worth mentioning that degradation is a multi-faceted phenomenon involving many natural and man-made factors. The logical approach to this problem would, therefore, seem to be a "one-step-at-a-time" approach.

Jan 2, 1989

By R. C. Kirkman

Your interesting and well-written paper brings up the issue of the purpose or use of a mineral property appraisal, specifically the value of these evaluations when the quality and quantity of the mineral resource to be exploited have not been thoroughly investigated. I am not a practicing professional in regards to valuation of limestone investment opportunities. I simply wish to make a few generic observations about the appraisal process in order to stimulate meaningful thinking by appraisal professionals whose reports may be reviewed by professional investors and "laypersons" alike. It is my contention that the analysis given in your paper is very thorough, considering the data that was made available to you. But I would not like to be the person responsible for investment decision making without having a feel for the risk involved. Therefore, the reviewer must classify this type of analysis as relatively "subjective" because they have not received an indication of the inherent risk involved in exploiting a mineral resource. This risk can best be quantified by using probabilistic methods in conjunction with the quality and quantity of the mineral to be produced. Most appraisals passively ignore this problem. Specifically, you have accurately identified the various costs and values entering the economic appraisal process. These can usually be quantified with a great deal more certainty than the capability of the resource to provide 25 years of quality material. Also, in Cases A (West Virginia)and B (Alabama), you are fortunate enough to have previous operations data. What if there had never been production from these properties? How does a potential mineral property investor evaluate the resource capability to meet various projected financial outcomes without spending a good deal of up-front capital to drill and delineate enough quality resources for a 20-plus year operation. These questions pose a substantial risk to any potential mineral investor. Only probabilistic methods should be used to quantify this type of problem, short of drilling and metallurgical testing. I might be considered a "layperson," not being familiar

Jan 1, 1991

Throughout the 1970s, the US Bureau of Mines rode an ebb tide in Washington political circles. In rapid fire succession, the agency lost its mine health and safety enforcement responsibility (1973), a large portion of its energy research responsibility (1975), and then its fuel statistics functions plus a sizable portion of its coal R&D (1977). By 1978, johnny-come-latelies in the Energy, Labor, and Interior Departments had siphoned away from the Bureau some $125 million in program responsibilities as well as 900 of its employees. The bruising decade came to a close with a Department of Natural Resources proposal that, in its original form, would have scattered the Bureau's responsibilities to the winds. "There is no doubt in my wind," said Lindsay Norman, acting director of the Bureau of Mines (see box), "that were the Bureau to continue down the path it was on, the next step was closing the doors and going out of business." The doors are still open, but erosion of responsibilities had a devastating effect on the resources available to fulfill the Bureau's mission. Devastating, too, in terms of internal morale, considering the Bureau had six directors in a 10-year span. "When the troops are in the trenches and are being shot at," Norman said, "they need a leader-hopefully, a permanent one- that can get them advancing. This is something the Bureau did not consistently have in the 1970s." In September 1978, Roger Markle climbed aboard as director of the Bureau to rejuvenate the 70-year-old agency. He resigned only six months later* but the program Markle set in motion is being carried through by Lindsay Norman. Since Norman's appointment as acting director, he has spent considerable time on the road explaining his agency's redefined goals. At one such stop in Duluth, Norman and his two deputy directors, Charles Kenahan and Mike Kaas, answered the following questions. Lindsay, you were the principal architect in the Bureau's 1979 reorganization. How about a glimpse of what that entailed? Toward the end of the 1970s, after almost a decade of steady dismemberment, we reached what we felt was a critical point in the Bureau's history-we had the choice of redefining and strengthening our organization to meet the mineral challenges ahead, or continuing down the path toward the agency's eventual demise. We felt the Bureau's mission too important to abandon, so in 1978 with Roger Markle as director we initiated a six-month, no-holds-barred intro spection of just what the Bureau should be doing, why, and toward what ultimate national needs. And what did this self-reflection reveal? That there is, indeed, a unique federal role for the Bureau of Mines-that of a lead agency for influencing mineral decisions and pioneering tomorrow's technologic advances. Don't confuse us with policymakers, we're not. But we are policy analysts; we're scientists, engineers, and mineral professionals who can offer a sorely needed source of objective, accurate information to decision makers in both the public and private sectors. I feel there is no better brain trust in government than the Bureau when it comes to mineral expertise-of course, I'm biased. Do I understand you to say the Bureau of Mines is an advocate agency for the minerals industry? We plead no parochial interests, nor ought we, but from our viewpoint a sound minerals industry is extremely important to the broader national goals of security and a healthy economy. US dependence on foreign sources for critical minerals, the increasing noncompetitiveness of some US mineral sectors, and the array of land use issues surrounding mineral-rich lands all have much more serious implications than many otherwise informed people seem to recognize. In your estimation, how vulnerable is the US to foreign mineral suppliers? Let me make a distinction between dependency and vulnerability. The

Jan 4, 1980

By S. N. Groudev

A process for the combined chemico-biological removal of iron present as oxide minerals in different mineral raw materials (quartz sands, kaolins, clays, etc.) was developed. In the process, mineral raw materials are leached at about 90 °C with lixiviant containing microbially produced oxalic and hydrochloric acids. The leaching is carried out in mechanically stirred acid-resistant reactors for periods of from 1 to 6 hours, depending on the iron content and the forms of iron in the raw materials being leached. The iron contents of some sands treated by this method were lowered from levels that were in the range of 0.035% to 0.088% Fe2O3 to less than 0.012% Fe2O3, making them suitable for the preparation of high-quality glass. The iron contents of different kaolins were lowered from levels that were in the range of 0.65% to 1.49% Fe2O3 to levels in the range of 0.44% to 0.75% Fe2O3. As a result, the whiteness was increased from values of 55% to 87% to values of 86% to 92%. The iron content of clay was lowered from 6.25% Fe2O3 to 1.85% Fe2O3, and this increased the “fireproofness" of the clay from 1,670°C to 1,750°C. A similar process was used for the leaching of aluminum from aluminosilicates, mainly clays and kaolins. However, in this case, the microbial fermentation fluid containing citric acid was acidified by means of sulfuric or hydrochloric acid or by means of different mixtures of mineral acids. For enhancing aluminum solubilization, the aluminosilicates were heated before leaching at 600° to 650°C for 1 to 2 hours. Over 90% of the aluminum present in different clays and kaolins were leached within 3 to 6 hours. "Silicate " bacteria related to the species Bacillus circulans were used to leach silicon from low-grade bauxite ores containing aluminosilicates as impurities. The bacterial action was connected with the degradation of the mineral structures (by means of microbial metabolites such as organic acids and exopolysaccharides), as well as with the selective separation of the rich-in-aluminum fine fractions, which were retained by the mucilaginous capsules of the bacteria. The solid residues after treatment were characterized by higher values of alumina and silicon module (A1203: SiO2 ratio), and they were suitable for processing by means of the Bayer process for recovering aluminum. The bending strength and other ceramic properties of kaolins were improved by contact with well-developed cultures of "silicate" bacteria. The improvement was caused mainly by bacterial metabolites (exopolysaccharides) that acted as resins during drying.

Jan 1, 2000

By Gregory R. Wagner

As you know, NIOSH is the part of the United States Public Health Service with responsibility for conducting and supporting research leading to prevention and control of occupational diseases and injuries. Some years ago, NIOSH went through a process of identifying and leading occupational health and safety problems in the United States. Candidate problems were evaluated in terms of the number of people affected, the importance of the effects, and how amenable the conditions are to preventive interventions. Lung diseases were ranked first on the resulting list. Diseases from mining continue to contribute substantially to this unfortunate position of prominence. The work of the Generic Center is one of many answers to this critical problem. Although the research is often expressed in terms of dust characterization or dust control, the reality is that high dust levels are much like high blood pressure. No one cares about hypertension per se. We are concerned about the consequences of exposure to untreated high blood pressure--heart disease, kidney disease, and stroke. Similarly, if dusts were truly only a nuisance, there would be little justification for the diverse research program supported by the Bureau of Mines or by NIOSH. But mineral dusts do cause a range of significant health problems: pneumoconiosis, bronchitis, and emphysema. The research supported by the Center is aimed at doing something about them. Within a public health approach to occupational health, we have a hierarchy of interventions. Primary prevention of problems is prevention at the source: solving a problem before it affects a worker. What we call secondary prevention is an attempt to identify health problems at a sufficiently early stage that some intervention will interrupt the disease process or the development of significant impairment. Tertiary prevention refers to rehabilitation of the worker who has already suffered significant loss of function. At NIOSH, and in the Generic Center research programs, the focus is on primary prevention. Basic investigations into those things about specific dusts that promote or reduce toxicity is critical for our understanding of how to prevent disease. Also, the search for engineering solutions to reduce or control dust generation is essential to solving problems of dust over-exposure. But until the engineers create the foolproof safe environment, it will also be necessary to discover better ways to identify the earliest markers of disease. To do this, we must explore and explicate the basic mechanisms of disease through laboratory investigations as well as human observation and physiologic testing. The unique opportunity provided by the Generic Center program and highlighted in this diverse program over the next few days is that these efforts are being carried out in multiple disciplines concurrently. Also, there are periodic small and large gatherings such as this one where investigators have the chance to get together, formally present papers, and informally stimulate each other's progress towards disease prevention. To ignore the potential for this cross-cutting interaction would be a significant loss. To take full advantage of it is potentially revolutionary. I recently pulled out a book I hadn't read since I was an undergraduate. It specifically concerns the nature of intellectual ferment surrounding the development of the concept of a sun-centered rather than an earth-centered universe in the sixteenth century. The book is about more than developments in astronomy: it is a discussion of the nature of scientific revolutions. Scientific revolutions result from the brilliance, insight, and good fortune of the few superimposed on the evolutionary work of the many. They both cause and reflect significant itellectural and social ferment. For example, the revolutionary work of Copernicus in recognizing the limitations of the concept of an earth-centered universe reflected contemporaneous developments in optics, mathematics, physics, economics, and philosophy.

Jan 1, 1991

By J. O?Hanlon

The 4500 m3 blast furnace at the Redcar Works of ESC operates or, a burden of sinter and pellets, both materials being produced within the works. The early history of the furnace was given to the AIME Ironmaking Conference in 1981(1) when the burden was 65% superfluxed minter and 33% acid pellets. While ironmaking performance was adequate, it was felt that there were advantages to be gained by the use of fluxed pellets. For example, Kobe Steel had reported (2) that the rise of 30-50% dolomite fluxed pellets had enabled them to achieve better furnace permeability, higher gas utilisation, and enhanced ore/coke ratios. It appeared probable to BSC that the use of magnesia-bearing fluxed pellets would give a burden which had compatibility of softening and melting properties, i.e., fluxed sinter and dolomite pellets would result in a thinner cohesive zone because of closer matching of softening and melting temperatures, with consequential benefits on furnace stability and efficiency.

Jan 1, 1983

By Guy Bridges, Elton Ko, Cheng Ting Ning, Owen Ng, Giovanni Chang, Robert Anderson

"PROJECT OVERVIEWThe Liantang/Heung Yuen Wai Boundary Control Point (BCP) and Associated Works will be the seventhland crossing between Shenzhen and the Hong Kong Special Administrative Region (HKSAR) of China.The project includes site formation of about 23 hectares of land for the development of the BCP and anapproximately 11-kilometre (km) long dual two-lane trunk road (the “Connecting Road”), connecting theBCP with the existing Fanling Highway. The route alignment is within a relatively rural area of HongKong, with very limited similar infrastructure works carried out nearby. It passes beneath bothmountainous terrain, and alluvial plains, and falls within an area of several major regional faults andassociated metamorphism, resulting in a complex variety of ground conditions.ALIGNMENTThe Civil Engineering and Development Department of the Government of the Hong Kong SpecialAdministrative Region carried out extensive public engagement in selecting the alignment of theConnecting Road. Over 70 consultation forums with public bodies, including the District Councils, RuralCommittees, local representatives, etc. were held during the alignment design process. In order toalleviate the concerns of various nearby villages, and to minimize land clearance and environmentalproblems, the original alignment of 10 km long (3.5 km of tunnels and 6.5 km of viaducts) was revised toits final alignment of 11 km long which comprises 5.7 km of tunnels, 4.3 km of viaducts and 1.0 km of atgrade roads.The finally adopted alignment commences at the southern end with an interchange with the existingFanling Highway, part of Route 9, which is a dual three lane expressway currently being widened to dual4 lane. Alongside the expressway is the main rail connection to the mainland of China, and theinterchange viaducts connecting to the southern portal of the Lung Shan tunnel must cross over thisrailway. The southern portal is located in the foothills of Lung Shan, and the 4.8km long tunnel is alignedin a north-northeasterly direction. The southern half passes under mountainous terrain of Lung Shan,and then crosses a valley containing the Kwan Tei river. The northern section comprises low hillsseparated by an alluvial plain and Tan Chuk Hang village area. At the northern end, the tunnel turns tothe north-west to connect with Sha Tau Kok road, an existing single carriageway road, with a newroundabout interchange. Mid-way along this tunnel there will be a ventilation building, connected to the main tunnel by a 330m long ventilation adit. To the north-western side of this interchange is the900m long Cheung Shan tunnel, and after this the remaining 4.3km of the highway connecting with theBoundary Control Point is to be constructed as an elevated viaduct. The alignment is shown in Figure 1."

Jan 1, 2016

By Daniel Saramak, Agnieszka Saramak

A big issue in crushing and grinding operations in raw materials handling is high energy consumption and low breakage effectiveness. According to the Legendre [7], only 10% of energy input is directly consumed on the feed material breakage, while the remaining portion is dissipated in the form of heat and noise [8]. In the industry of limestone powder production, the grinding operations constitute integral part of technological circuits, and the energy consumption in operations of industrial comminution consume as high as 2% of world energy [14]. High-pressure grinding is the technology with proved energy benefits both in ore processing circuits and in limestone grinding. The promising results concerned mostly the achieved energy savings and good results of material breakage were achieved and demonstrated in numerous investigations [1,3,12]. However, it appears that a proper selection of operational parameters of the press devise, determination the feed material characteristics and adjustment of process course san be of a key-significance in improving an effectiveness the HPGR operation. Operational parameters of devices and process course should be verified towards the characteristics of the feed material, which mainly applies to the particle size and shape of the feed material and its moisture, and also mineralization in case of ores [2,4,9]. There are various investigations concerning an impact of the operational pressing force on comminution results which mostly refer to the determination of energy consumption and crushing ratio [5,6,10,13]. Investigations on the moisture content are less common, however their results suggest that, in general, the HPGR feed with higher moisture shows the tendency to higher comminution intensity, while the energy consumption increases together with increasing of feed material moisture. Investigations on olivine sand feed [11] showed that crushing ratio decreases for higher moisture, especially when the material is crushed at higher pressing force. HPGR devices, however, shouldn’t be regarded as a unique and perfect solution for comminution of each type of material. But they indeed may bring technological and economic benefits, comparing to conventional crushing and grinding machines, resulting in more favourable breakage of material particles and lower consumption of energy per unit mass of processed feed material.

Feb 1, 2025

By Nathan Bowersox, Zuzana Skovajsova, David M. Jurich, Brian Harris

When unwatered after more than 50 years of operation, the White Rock Tunnel of the Upper American River Project in the foothills of the Sierra Mountains exhibited failing rockbolts and ground falls. Repairs designed for the 5 mile-long, 24-foot horseshoe unlined hydropower tunnel included pattern rock bolts, shotcrete, and cleanout of the rock trap. The work, originally scheduled for two 3-month winter outages, was completed under challenging conditions in a single 4-month outage following a carefully sequenced work plan using robotic shotcrete and rockbolter machines. Flexibility, creative solutions, and collaboration by all parties were key to project success.

Jun 13, 2021

By Richard C. Sale

INTRODUCTION The topic of the paper is to discuss the use of micro computers in the construction industry. I will first discuss the present situation of the PCs in our industry followed by a discussion how Guy. F. Atkinson has integrated the PCs into it's organization. I will close with some general comments that any organization should review in order to enhance the use of their PCs both at the job sites and home office locations. PRESENT SITUATION OF THE PCs IN OUR INDUSTRY Today, the possible number of combinations that can be obtained when bringing together the available models of PCs, with their peripherals and software, is astronomical. With this array of equipment that can be bought, plus the new and possibly better equipment that is being put on the market almost daily, it is indeed a very difficult task for an organization to know how to invest its money in computer equipment. At the job sites, the work is fast paced with little time available to fully learn what the PCs can do to help with the required paperwork. I am still waiting for the day when someone has to tell the superintendent at the job site that he cannot start pouring concrete or shoot the next round because no one can get the computer to work.

Jan 1, 1987

By P. Semberg, B. Bjorkman, C. Andersson

"In this study, the interaction between magnetite and the additive olivine was studied after oxidation as well as after isothermal reduction at temperatures in the 500º-1,300º C range. In the olivine sample, the forsteritic olivine particles react partly during the oxidation pretreatment to form magnesioferrite and vitreous silica along the particle corona. This breakdown of the olivine particles during oxidation liberates magnesium from the particles, which do not react until temperatures of above 1,150° C in reducing atmosphere. When the hematite in the sample is reduced, and when the temperature is high enough to allow solid-state diffusion at ~800º C, the magnesium of the magnesioferrite redistributes, so that the magnesium concentration approaches the same level throughout the iron oxide structure. For magnetite, this did not occur until 800° C. At 1,000° C, this magnesium reacts further with the silica in the glassy slag phase, which crystallizes into fayalitic olivine. At this temperature, the magnesium has diffused over distances of more than 600 µm from large olivine particles after 2 hrs reduction. From this point, the primary slag phase in the pellet, until melting, is solid fayalite. Upon reduction to metal, the metallization front concentrates the MgO in the remaining wustite, which can lead to MgO levels of up to 10 mole% locally. The melting point of the fayalite is raised from 1,145º C to a melting range of 1,238-1,264º C due to the MgO increase, as estimated based on phase diagrams, which were adapted to the pellets tested. Much of the olivine that remained unaltered in the oxidation process will be encapsulated by iron before the particles begin to dissolve in reducing conditions and, therefore, plays no role in the reduction before final melting of the particles occurs.IntroductionEnvironmental concerns have placed increasing pressure on the CO2-intensive iron and steel industries to further optimize operation toward higher productivity and more efficient use of reducing agents. At the same time, high demand for iron ore has caused new iron ores with lower grades and more complex chemistries to be taken into production. In Scandinavia, the main iron-bearing material is magnetite-based pellets with olivine, which allow operation with very low slag volumes and, hence, lower fuel rate ( Slagnes and Sundqvist Ökvist, 2008; Hallin et al., 1994). Both the MgO and SiO2 of the olivine, as well as the elements of the gangue of the ore, i.e., Si, Mg, Ca, Al and alkali, interact with the iron oxides to give the finished pellet product its final properties in the blast furnace. Tailoring the additive mix to be used for a certain iron ore for optimal product properties, therefore, requires detailed knowledge of the mechanisms by which these elements dissolve and react in the pellet."

Jan 1, 2015

By Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Seals and build-in-place (BIP) refuge alternatives (RAs) are two main underground structures to isolate an area from the active working zones with different purposes. While seals are used to prevent methane gas that seeps from coal seams and blast pressures from a possible detonation of the contained gas, RAs are used to provide a safe haven for miners who are unable to escape their working locations after an accident like an explosion or fire. The recommended BIP RA designs can be similar to seals constructed with steel-reinforced concrete. Both seal and BIP RA are constructed in different locations of the mines for a period of time, exposed to a certain convergence due to stress redistribution which can change their responses during an explosion. In this study, a steel-reinforced concrete wall to be used in such applications is simulated to examine the structural performance during an explosion for a coal mine model with different strata conditions using dynamic analysis by a 3D distinct element method (DEM) code. The main purpose of this study is to reveal any possible effects or trends on the wall deformation with changes in strata conditions by implementing different combinations of roof, seam, and floor material properties. The model is calibrated by the experiment conducted on a steel-reinforced concrete wall by the NIOSH researchers in the Lake Lynn Experimental Mine. The results show that strong adjacent rock and coal units are the least favorable condition for the survival of the wall subjected to a simulated explosion pressure. The results indicate that changes in the roof and seam conditions can have dramatic effects on the deformation characteristics of the wall when compared to the floor conditions. The results of this study might be enlightening for future BIP RA and seal applications.

Feb 8, 2023

By Takeshi Shinohara

It is a great honor and pleasure for me as President of the Japanese Tunnel Association to send greetings to the 1974 Rapid Excavation and Tunneling Conference. Recently in Japan, the Japanese Tunnel Association was established as recommended by the OECD Advisory Conference on Tunneling. This is a central organization concerned with tunnel construction consisting of government authorities, universities' research institutes and construction firms as well as manufacturers of relevant materials and equipment. As I was chosen the first president of the newly-established Japanese Tunnel Association, I would like to avail myself of this opportunity to announce to you its establishment and its earnest wish to contribute to the development of tunneling technique not only in our country but also all over the world. At the same time, I cordially request your friendship and cooperation for the benefit of further development of tunneling techniques on both sides of the Pacific. At present, many tunnels are under construction in Japan. The total length of tunnels under construction for railways and highways is about 600km including the 54km Seikan Undersea Tunnel which connects the Main Island and Hokkaido. Naturally, for construction of such tunnels in Japan, we have introduced much equipment and technique from the United States and other foreign countries. Now with accumulated experience, we are confident to be able to furnish various useful information concerning tunnel construction.

Jan 1, 1974

By A. M. Marabini

Flotation of rutile with N-benzoyl-N-phenyl-hydroxylamine (N-BPHA) has been investigated. Initially, floatability tests were performed in a Hallimond tube. The results indicated that rutile was floatable in the pH range from 2 to 4 at N-BPHA concentration between 2x10-3 M and 2x10-2 M. Selectivity against hematite was recognized when operating at pH values below 2. Following the hypothesis of the formation of a surface chelate between N-BPHA and titanium ion, this compound was precipitated from a solution of Ti(SO4) to which N-BPHA was added. I.R. spectrometry oft the rutile before and after treatment with N-BPHA solution confirmed the presence on the rutile surface of the same compound. The absorption isotherm and kinetics were determined by analyzing N-BPHA in solution with an U.V. technique. A hypothesis for the mechanism of adsorption of N-BPHA on rutile is suggested.

Jan 1, 1982

By Doug Harding

The 3.5 km long Ashbridges Bay Outfall in Toronto, Ontario, Canada was a challenging drive set below Lake Ontario. After a remote machine acceptance due to the global pandemic, an 8 m diameter Single Shield machine launched in March 2021 from an 85 m deep shaft and began its bore in shale with limestone, siltstone and sandstone. During excavation, the TBM and its crew bored a city-wide record of 30 rings in one day, or 47 m of advance. This paper will cover the unique project, from TBM acceptance through to launch, tunneling in difficult conditions, and completion in 2022.

Jun 13, 2023

By Jan Van Greunen, Mark Vanderzee, David Haug, Geoffrey Hughes, Yiming Sun, Roozbeh Geraili Mikola

"The Sanitation Districts of Los Angeles County is planning to construct a new, approximately 7-mile-long (11.3 km) effluent outfall tunnel to be excavated by TBM and lined with precast concrete segments. Anticipated net operating pressures within the tunnel are expected to approach 3 bar. To counteract joint opening and exfiltration leakage, an approach has been investigated to post-tension the precast concrete tunnel lining with steel tendons. The tunnel alignment crosses several seismically active fault zones, at which installation of steel pipe is proposed as a secondary inner lining to mitigate potential offset displacements. This paper discusses the tunnel lining design approach and methods used to address these unique challenges.INTRODUCTION The Sanitation Districts of Los Angeles County (Sanitation Districts) is planning to construct a new 18-foot-diameter (5.5 m), approximately 7-mile-long (11.3 km) tunnel from the Joint Water Pollution Control Plant (JWPCP), located in the City of Carson, to the existing White Point outfall manifold structure at Royal Palms State Beach (RPSB) (Figure 1). The project is part of the Sanitation Districts’ Clearwater Program, which will improve overall system reliability through the repair and replacement of the existing aging infrastructure. The existing system includes two 6-mile-long (9.7 km) tunnels, 8- and 12-feet in diameter (2.4 and 3.7 m), and four ocean outfall pipes with a maximum capacity of approximately 675 million gal/day (MGD) (2.6 billion L/day). Addition of the new parallel tunnel will increase overall capacity to accommodate peak wet weather wastewater flows of up to 1,262 MGD (4.8 billion L/day) and will allow inspection and repair of the existing tunnels. The new outfall tunnel will be excavated using a pressurized face tunnel boring machine (TBM). Shafts at the north (JWPCP Shaft) and south (RPSB Shaft) ends of the proposed alignment will connect the tunnel to the existing wastewater treatment plant and existing ocean outfalls manifold and during construction act as launch and receiving shafts for the TBM. The tunnel will be excavated from north to south as a single heading."

Jan 1, 2016

By E. Z. Casassa

There has been a recent revival of interest in concentrated coal/water slurries as a substi¬tute for fuel oil or for coal/oil mixtures, particularly in electric power generation. The idea is not a new one. Coal/water slurries were transported by pipeline in the U.S. in the early nineteen-sixties, and the Black Mesa coal pipeline has been in operation for several years, while in Germany, coal/water slurries were being burnt for power generation in the early nineteen-seventies, as described by Merten and Höner (1972). Since coal is not a pure substance but a carbonaceous mixture, the different chemical and physical behavior of coal/water dispersions from different deposits must be understood in order to optimize the properties of the result¬ing slurry fuels. Since minerals which are minor constituents of coal may also strongly affect slurry properties, coal chemistry may vary considerably even within a single deposit. Thus it is unlikely that there will be a single formula for optimizing the slurry properties of all coals, and even the answer for coal from a single source may change with time.

Jan 1, 1983

By E. J. Wade

My subject is gold price forecasting and monitoring as an important aspect of gold marketing. While I 'm specifically addressing gold, it is understandable that many other commodities could be readily substituted. Gold marketing must be studied as three distinct processes, and it is my intention to cover each of these processes in turn. First I?ll cover the process of gold price monitoring and forecasting in some detail. In order to select a method, or combination of methods, to be used to sell gold a determination of the future price profile is essential. The profitability of the sales effort will be determined, to a large extent, by how accurately the future price behavior of the gold market has been forecast.

Jan 1, 1985

By Charles H. Grant

Communications in whatever we do, is one of the major problems we encounter. In an effort to provide a better understanding of the use of explosives, I am going to take a little different view of what explosives are, and how you might look at them as tools to fragment rock, and some of the problems encountered in doing so. First, let's take the explosive, and although there are many factors involved, I want you to consider these as being reduced to only two--shock strain imparted to the rock by the high early development of energy; and the other, the gas effect which is a combination of heat, moles of gas formed, rate of formation of these gases which develop pressures, etc..

Jan 1, 1968

By C. E. Jordan

The fundamental characteristics of ultrafine chalcopyrite flotation were investigated by the Bureau of Mines to establish techniques to improve recovery of ultrafine chalcopyrite. Intense agitation during conditioning was found to improve flotation recovery of the ultrafine chalcopyrite. A split-circuit flotation design, treating the plus 38-µm-size ore by the conventional method and treating the minus 38-µm-size ore with intense agitation conditioning followed by flotation, recovered 95.6 pct of the copper in a 28.3-pct-copper concentrate, This was a 5-pct increase in copper recovery over the conventional chalcopyrite flotation method.

Jan 1, 1986