Search Documents

By Yosry A. Attia

One of the most significant advances in Mineral Processing in recent years, is the development of the selective flocculation technology. The technology is primarily aimed at recovering the mineral values from ultrafine ore suspensions. This is achieved by selectively aggregating the mineral particles in question to such size as to enable their effective separation from the suspension. Selective flocculation utilizes the differences in the physical-chemical properties of the various mineral components in the mixed suspension. It is based on the preferential ad- sorption of an organic flocculant on the particular solids to be flocculated, leaving the remainder of the particles in suspension. In order to understand the mechanics of this process, selective flocculation may be divided into four major sub processes; these being: ore slurry dispersion, in which all the particles are stably and uniformly distributed in the suspension with the individual particles being essentially separate; flocculant selective adsorption and floc formation; floc conditioning, which aims at obtaining flocs with desire properties for their subsequent separation and with minimum entrapment of dispersed particles; and floc separation from the suspension. These sub processes will be reviewed later in this article.

Jan 1, 1982

By J. M. Wempen

As development in underground coal mines progresses away from the critical components of the ventilation system, including the main fans and ventilation shafts, resistance within the system is markedly increased. This results in higher pressure and flow requirements from the main fan(s) to maintain adequate face ventilation. Upgrades to the primary ventilation system are often required. The use of booster fans underground is a potentially practical alternative to the addition of shafts and surface fans. This study presents simulations of the use of booster fans in two underground ventilation scenarios, one longwall and one room-and-pillar. The booster fan effects on the power requirements of the ventilation systems are evaluated.

Jan 1, 2011

By Mona M. Fawzy, Ahmed A. Eliwa, Ahmed H. Orabi, Amal E. Mubark, Ebrahim A. Gawad

During the last decades, the growing demand for rare earth elements (REEs) has led to numerous recent studies to recover these elements from various bearing ores and wastes. Therefore, the recovery of REEs from Ras Baroud polymetallic concentrate has been investigated in the current study. Physical beneficiation for the Ras Baroud pegmatite sample was carried out, yielding a concentrate for euxenite (Y), fergusonite (Y), xenotime (Y), monazite (Ce), allanite, thorite, uranothorite, and Hf-zircon, which resulted in raising the concentrations of rare earth elements, Th, Zr, U, and Ti in the sample. Fusion digestion processes with sodium hydroxide were studied using the Conceived Predictive Diagonal (CPD) technique. The three experimental digestion groups proved the dissolution of 99.9, 95.6, 99.9, 52.5, and 0.47% for REEs, Th, U, Ti, and Zr, respectively, under fusion conditions of 723 K, 120 min, 1/1.5 ore/alkali ratio, and − 100-μm particle sizes. Fusion kinetics, isotherms, and thermodynamics were investigated using several suggested models, namely, pseudo reversible first order, uptake general model, and shrinking core model which matched well with the experimental digestion results. Selective recovery of actinide content from REE content of the digested concentrate chloride solutions was accomplished using solvent extraction with di-2-ethyl hexyl phosphoric acid. About 99.9, 99.9, and 4.2% extraction efficiencies for Th, U, and REEs were performed, respectively, using 0.3 mol/L solvent concentration in kerosene as a diluent, 1/2 organic to aqueous ratio, an aqueous pH of 0.2, and 15-min contact time. Thorium and uranium ions were stripped with sulfuric acid solution 2.5 mol/L with 94 and 98% stripping efficiency, respectively. A highly purified REE precipitate was obtained from the raffinate solutions. Zircon mineralization tailings were obtained as a by-product through the alkaline digestion process.

May 4, 2024

By Daniel T. Eyde

The U.S. Geological Survey (USGS) estimates world production of natural zeolites to be 2.7 Mt (3 million st) in 2013. China ranked ?rst with 2 Mt (2.2 million st), followed by the Republic of Korea at 230 kt (253,000 st) and Turkey at 50 kt (55,000 st). Japan?s production is reported to have increased as a result of zeolites, reportedly low grade local mordenites, being used to treat the low-level radioactive contaminants in the areas surrounding the damaged reactors at the Fukushima Daiichi power plant. China and other countries? high-volume, low-value construction applications, which include dimension stone, pozzolans and lightweight aggregate, are also included in production. This means the production data does not accurately indicate the quantities used in high-value added specialty applications. Consumption in the United States, according to USGS estimates, increased slightly, to an estimated 71.3 kt (78,400 st). Domestic uses for natural zeolites were, in decreasing order by tonnage, animal feed, pet litter, cement (primarily down-hole cement applications by the drilling industry), water purification, odor control, waste water cleanup, fungicide or pesticide carrier, gas absorbent, fertilizer carrier, oil absorbent, desiccant, catalyst and aquaculture. The six leading uses accounted for more than 70 percent of the domestic natural zeolite sales tonnage.

By R. B. Krog

The use of belt air as an intake source at longwall operations has changed greatly over the past decades. The practical considerations for the use of belt air are controlled by a variety of factors, including airflow quantity and velocity, coal methane content, methane desorption rates, coal mining rate, belt length, stopping leakage and the number of gateroad entries. At longwall operations, the advantages and disadvantages of belt air are different than for gateroad development and longwall panel extraction. During gateroad development, the use of belt air to ventilate the working section will reduce the leakage from the intake to the belt compared to the belt air being ventilated outby the working sections because of lower pressure differentials. A greater quantity of airflow will reach the last open crosscut with the belt on intake than outby, given the same amount of pressure and airflow available at the mouth of the section. This paper will investigate the current ventilation practices regarding the use of belt air during gateroad development and longwall panel extraction. Operating considerations regarding air quantities and pressures to deliver the required airflow will be investigated using ventilation network modeling.

Jan 1, 2010

By Yongjun Xian

The release of fluid inclusions has a strong potential for the unintentional activation of pyrite during flotation. The present study aims to characterize fluid inclusions in a natural pure pyrite. The results indicate that a certain amount of fluid inclusions exist in the pyrite. The fluid inclusions assume a variety of shapes, including long strips, oval shapes and irregular shapes, with sizes that range from a few microns to dozens of microns. From the EDS results of hollow positions that resulted from the fracture of the fluid inclusions on the pyrite surface, certain amounts of Al, Cr, C, O, Ag and Cu were clearly detected; these elements were not detected in FeS2 pyrite itself. The contents of the inclusions were released into solution when the sample was subjected to a grinding process. Under experimental conditions of 2 g of pyrite cleaned in 40 mL of pure deionized water under an inert atmosphere, the concentrations of Cu, Fe, Cl- and SO4 2- released from the inclusions reached concentrations of 3.29 × 10-6, 32.52 × 10-6, 51.57 × 10-6 and 75.90 × 10-6 mol/L, respectively. These values are significantly greater than those from the experimental nonoxidative and oxidative dissolution of the pyrite. The fluid inclusions of pyrite were, therefore, concluded to represent the dominant sources of Cu, Fe, Cl- and SO4 2- in the aqueous solution. The present investigation provides a new understanding of the source of the unavoidable metal ions in the pulp and may benefit understanding of the flotation theory and environmental geochemistry.

By J. K. Pandey, ebashish Mishra, D. P. Mishra, N. K. Mohalik, S. K. Ray

The increasing demand for coal and depletion of shallow depth reserves are pushing towards deeper mining. In deeper coal mines with multiseam workings, the problem of ventilation surges many folds primarily related to air quantity requirement, heat, humidity and spontaneous heating/fire in goaved (gobbed) out areas. The paper describes the design of a new approach to improve the ventilation system of a real-life deep underground coal mine with multiseam workings. For this, the ventilation problem of one deep underground coal mine 6&7 pits Bhutgoria Amalgamated Colliery of Tata Steel Ltd. with multiseam workings has been studied in detail to determine an appropriate solution. A ventilation survey of the mine and computer simulation of the ventilation network has been carried out to reach a practical solution. Ventilation survey results have been analysed to develop a representative ventilation network of the mine for both qualitative and quantitative analysis. Further, computer simulation of the ventilation network of the mine has been performed to virtually verify the application of a highcapacity booster fan in the present ventilation circuit without disturbing the vulnerable areas. Field validation is also carried out after the implementation of the solution in the mine to determine its efficacy. Thus, the findings of this paper can be directly applied for the installation of booster fans to achieve the required air quantity in deep underground coal mines with multiseam workings having spontaneous combustion liabilities of upper seam goaved out areas.

Jun 2, 2022

By R. Mensah-Biney, M. T. Hepworth, K. J. Reid

The kinetics of gold-bromide loading onto activated carbon was investigated in a batch stirred reactor. Based on a second-order equation, the amount of gold adsorbed by the carbon was correlated with time. From a 30ºC solution containing 25 ppm Au and 0.8 g/L carbon, the rate constant for gold-bromide species onto activated carbon ranged from 0.27 x 10-3 to 1.2 x 10-3 (kg/t)-1 min-1. The equilibrium saturation capacity (Qe) was 36 ±3.0 kg/t from the same system. The rate of loading increased with increasing temperature and decreasing particle size, pH and solution gold concentration. The calculated activation energy (Ea) was 8.8 kcal/mole, significantly higher than those reported for physical adsorption. The equilibrium saturation capacity (Qe) increased with increasing concentration of gold in solution but was independent of other variables such as temperature, agitation speed, particle size and pH. These rate constants and equilibrium saturation capacity for the gold-bromide species are higher than those reported for the gold-cyanide systems.

Jan 1, 1998

By Yi Luo

Simulation of the multi-entry and multi-crosscut (MEMC) ventilation systems commonly employed in U .S. underground coal mines can be very tedious, due to the large number of crosscuts with stoppings to be represented in the network models. In order to reduce the amount of work needed to build the models, a common practice is to represent a number of crosscuts with one equivalent airway. However, this introduces certain errors into the simulation results. In this paper, algorithms have been proposed to simplify the ventilation networks of common MEMC systems encountered in panel development operations. The algorithms can be used to reduce a MEMC system into one airway with an equivalent resistance and to determine the airflow distributions in the system and the leakages through the stoppings.

Jan 1, 2011

By A. D. Hammond

"INTRODUCTION Vanadium deposits in Arizona are distributed all across the state, from the rim of the Grand Canyon to the Tombstone mining district in the southeast corner of the state (Figure 1). The combined past production of vanadium from Arizona and New Mexico ranks second nationwide, after deposits in the Colorado Plateau In the northeast corner of the state, in the Carrizo Mountains and Monument Valley of Apache and Navajo Counties, vanadium was produced as a by-product of uranium in deposits of the Salt Wash and Shinarump members of the Morrison and Chinle formations, respectively. The production took place between 1943 and 1970. Another source of vanadium in Arizona occurs in vanadate deposits associated with supergene enrichment of base-metal vein and replacement deposits. The most important vanadate mineral is vanadinite, a chloro-vanadate of lead. Presently, there are no primary mines of vanadium in the United States. In 2012, a small production of vanadium pentaoxide (V2O5) was reported as a by-product of uranium at the White Mesa uranium mine in Utah1. This paper describes vanadate deposits in Arizona with emphasis in three districts, namely, the Mammoth, Globe-Miami and Banner districts.VANADIUM EPIGENETIC DEPOSITS: VANADATES Almost all vanadium epigenetic deposits occur as vanadates in oxidized zones of lead, zinc and copper veins and replacement deposits. Vanadinite, descloizite and mottramite are the most common minerals in vanadate deposits. Descloizite is a vanadate of lead, zinc and copper. Wulfenite, a molybdate of lead is also present. These minerals replace supergene base-metal minerals, form crusts on faces of open cavities, or are inter-grown with residual clays in pockets. The vanadium content in vanadate deposits is believed to have been leached from the country rock by ground-water and transported through porous rocks until precipitating as a relatively insoluble vanadium compound or until the solution evaporated. Precipitation was brought about by local concentrations of cations of divalent lead, zinc or copper. Lead is a constituent part of almost all of vanadate deposits and the vanadium pentaoxide (V2O5) content in vanadate minerals seems to have a direct correlation with the content of lead in the hypogene mineral. Vanadate deposits are restricted almost entirely to the oxidized parts of vein or replacement deposits. It is rare that oxidized zones extend past 100 ft from the surface. Vanadate deposits are largely restricted to tropical and temperate zones and regions of dry climate. Arizona and New Mexico have the largest concentration of vanadate deposits in North America."

Jan 1, 2015

By Aixiang Wu, Minjie Zhang, Zhuen Ruan, Yiming Wang

This paper combines theoretical and experimental analysis to conduct relevant research to improve the accuracy of predicting paste yield stress by slump flow. The analytical model of slump flow for yield stress is derived based on a mini-cylindrical mold with a height-to-diameter ratio of 1. It shows that the dimensionless slump flow is a monotonic decreasing function of the dimensionless yield stress and is independent of the material type (specific gravity), which provides a theoretical basis for quantifying the rheological properties of paste with slump flow. Three different tailing-prepared pastes were tested for their slump flow and implemented rheological tests simultaneously. The yield stress is obtained based on the Bingham model fit, as the measured value of the yield stress is substituted into the derived theoretical model. The studied pastes yield stresses range from 34.78 to 524.08 Pa, with corresponding dimensionless slump flow of 3.43 to 1.09. The results showed that the calculated slump flows were generally greater than the measured values. The analysis showed that this was mainly due to the thixotropy of the paste, with minor deviations ranging from − 1.5 to 5.8% for the less thixotropic pasted prepared from tailing C. An approximate analytical solution for yield stress as a function of slump flow is obtained using Taylor’s formula. However, it is unsuitable for predicting the yield stress because the yield stress calculated by this function is much higher than the measured value. The empirical yield stress model was constructed and experimentally verified. The results show that the empirical formula has high accuracy and good generality. The deviation of the studied pastes is between − 15 and 5%, which provides a practical method for rapid and accurate prediction of paste yield stress in mine sites.

Jun 1, 2023

By John Ralston, Rossen Sedev, Nicola Richards, Quinn Anthony, Geoffrey Reynolds

Derivatised 2,4-diketopyrimidine groups have been anchored to planar gold surfaces as self¬-assembled monolayers (SAMs) for chemical and photochemical studies. Three derivatives, 5-methyluracil (thymine), 5-trifluoromethyluracil and 5-nitrouracil, were chosen for the specific moiety present at position C-5, which can exert strong or weak inductive effects on the adjacent aromatic ring. The measured acidity constants decrease from 5-methyluracil to 5-nitrouracil as the inductive properties of the group at C-5 position increase. When grafted to the surface the acidity constants increase, albeit still adhering to the expected inductive trend. The functionality also exerts an influence on the surface wetting properties. Surface wettabilities indicate that the orientation of the pyrimidine groups at the surface occurs so that the C-5 position has a direct effect upon the surface chemistry. Upon dimerisation the surface contact angles increase signifi¬cantly. At pH 11 the contact angle changes reflect that the dimer has a higher pKa than the monomer. The monomer surface is deprotonated at this pH while the dimer surface is partially deprotonated, leading to changes in contact angle of up to 22 degrees. Large changes in contact angle were observed for 5-nitrouracil which were independent of surface charge and were appar¬ently due to conformational changes alone. Electrowetting of three fluoropolymer surfaces by electrolyte solutions was studied with the sessile drop method. The electrowetting curve (contact angle/potential) is analogous to the elec¬trocapillary curve (surface tension/potential) and may be described by a combination of the Young and Lippmann equations. We demonstrate that for some specific surfaces a systematic deviation occurs at positive potentials. This departure is attributed to double layer effects, namely the adsorption of hydroxide and halide anions. pH, ionic strength and polymer composi¬tion can all influence electrowetting behaviour.

Jan 1, 2003

By Congcong Chen, Bo Ma

When assessing the safety of a tailings dam, the constant weight method (CWM) is one of the most commonly used methods. However, when the evaluation indicator value suggests serious defects, the evaluation value is often inconsistent with the actual situation. To address this issue, the variable weight method (VWM) is introduced to assess the safety of the tailings dam. Initially, a three-layer indicator system for dam failure safety assessment is built, and individual indicator values are divided into four grades. Then, an appropriate state variable weight function is constructed and relevant parameters are determined. Finally, a case study is illustrated to verify the effectiveness of the model. The assessment results of the VWM more closely represent the actual situation than that of the CWM, which is more helpful for decision makers and technicians to take scientific and reasonable precautionary measures, thereby improving the safety management of the tailings pond.

Oct 8, 2022

By L. W. Saperstein

P.J. Ehret By and large, I agree with many of the precepts discussed in the Saperstein paper. I believe there is much more that can be done on the local level to involve both government and planning in the mine permit review process. Admittedly, much can be done to improve discussion between the state regulatory authority, local authorities, and mine operators. However, I strongly disagree, as suggested in the paper's conclusion, that such a system, as outlined in Saperstein's paper, could result in a reduction of review time or a lowering in the cost of permitting. The implementation of such a system by its very nature would only add a new level of bureaucracy to an already cumbersome process. This system, in my opinion, would only add to the cost of permitting and the time necessary to obtain a permit. Admittedly, it would achieve the result of adding local influence into the permitting process, but at what off-setting cost? It has been my professional first-hand experience and observation in the permitting and lands unsuitable processes to note that under the present system, local governments that do feel they have a stake in local mines and actively ad¬vocate their position (not simply comment), have had significant input into the conduct of mining and reclamation plans in their areas. Mining companies that mine in these areas are aware of local interests and attitudes, and do consider them in their plans. Simply put, local governments that want to get involved and want to play significant roles can and do. Those that do not advocate a position or have no input to offer do not. Although the present system is not as direct in effect in regard to local control as Saperstein's, it does work. It does so without the red tape that would result from developing miniature regulatory authorities in every county in which mining occurs. Although local input is important, there are many more sections of the Surface Mining Control and Reclamation Act (SMCRA) than Sections 508(a)(8) and 522(a)(3)(A) that also are important. It appears Saperstein's paper may overindulge these sections. An additional specific comment is made in regard to the statement that while local areas benefit from mining (wages, salaries, and purchases), they also endure environmental deterioration caused by mining affects. It is believed that the whole purpose for which SMCRA and its resulting regulations were enacted and developed was so mining would not be permitted if significant environmental deterioration could occur. Therefore, it could be argued that this point under current law is moot. Reply by L.W. Saperstein P.J. Ehret writes in a reasoned and rational way and makes some good points. The arguments in favor of central control of the designation process reflect all of the benefits associated with central environmental control: consistency of enforcement, efficiency of operation, ease of communication among enforcing agency, etc. Nonetheless, the decision to mine or not to mine is a landuse decision which, in substance, is similar to the decision to build a shopping mall, a new highway, or a housing subdivision. Although, state and federal governments' interests in the protection of public welfare are real and are expressed properly in mining laws and mining enforcement agencies (OSM, Illinois Department of Mines and Minerals, etc). I continue to maintain that the permitting and designation processes should originate with local government, which is in keeping with the American tradition of delegation of the land-use decision to local or regional government.

Jan 4, 1984

By Chas. E. Shumate

There is assembled here this morning in Chicago the heartland of America, what is undoubtedly the greatest concentration of Technical, Scientific and "CAN DO" knowledge ever assembled in America. The participation in this Conference by the representatives of so many nations is particularly impressive and is a further indication of the importance of the subject matter of this conference which you will be discussing in much detail during the next few days. Another impressive feature of this Conference is the participation of a large segment of the construction industry in whose hands fall the job of building what others design. Also strongly represented is the manufacturing industry whose capability is well known throughout the world. They have the resources to design, develop and manufacture the machines and specialized equipment needed to do any job which the world requires. You should not expect to gain any knowledge from my few remarks this morning as I am undoubtedly the least qualified individual in this room on the highly technical and scientific subjects you will be discussing during these next few days. However, I shall offer a few broad suggestions on subject matter which I trust may generate serious thought during your discussions.

Jan 1, 1997

By Pierre Louis, Jacques Duparque

ACTIRED is a new process for gold and silver elution from activated carbon based on the addition of hydrazine, needing no extra investment and which generates a systematic increase in elutions kinetics. This process either operates at a lower temperature and maximizes financial gain or reduces elution time or operates at a compromise between these two options taking into account the needs of each plant. Industrial use of the process at SNC Lastours, France (Zadra elution column 3,5 bars -125°C) has proved at 95 ° C the following points:

Jan 1, 1995

By William A. Hustrulid

The subject of surface mine development is large. This section covers the fundamental concepts involved in both the open pit mining of thick or steeply dipping deposits as well as the strip mining of thin, shallow, and relatively flat-lying seams or beds. Design involves the marrying of geometries, ore and waste characteristics, equipment, and economics so that the desired result is achieved. Generally, there are many possible combinations from which to choose. For example, extraction over a short time period requires one strategy while quite another is applied for longer times. Variations in supply and demand require some flexibility of operation. Customer requirements impose certain constraints regarding the set of possible designs. Over recent years, planning and operating considerations for surface mining imposed by environmental requirements have increased markedly. There have, at the same time, been enormous advances made in the design aids available to the mine planner. Computer simulation of the various options, whether it be for mine design or equipment selection, provides detailed information for decision making in real time. A significant challenge to the engineer/planner is how to best use the aids avail-able. Because of the widespread use of commercially available and in-house computer software by industry, this section does not deal with the details of planning (for basic coverage of mine development, see Section 7). Rather, some of the basic concepts are stressed. The principles involved in equipment sizing and selection are discussed. A highly important but sometimes over-looked aspect of planning, haul road design, is also covered. For surface mining operations of the future, in-pit crushing and conveying will become even more important. Some of the considerations for application evaluation are included. The section concludes with some future concepts for surface mining.

Jan 1, 2008

By J. Lorengo, C. H. Bucknam

"Standardization of the Inductively Coupled Plasma Mass Spectrometry (ICPMS) method for gold in cyanide solutions was undertaken to provide a more sensitive method to quantify the gold content than the atomic absorption method standardized in 1994 (E1600). The gold concentration range covered is from 0.001 mg/L Au - 0.3 mg/L Au (0.00005 toz/t Au – 0.009 toz/t Au). Interlaboratory testing was carried out with the assistance of the American Society of Testing and Materials (ASTM) International on two committees to determine the within laboratory and between laboratory reproducibility. Three barren solutions from metallurgical operations were measured in triplicate to satisfy statistical requirements for Committee E1 on Analytical Chemistry of Metals, Ores and Related Materials. A synthetically prepared matrix representing the metallurgical processing solutions was used to prepare Youden pairs to satisfy the requirements of Committee D19 on Water. Results of the standardization program are presented. INTRODUCTION Analysis of process solutions for gold concentration requires accurate and sensitive analytical methods in order to manage process control and metallurgical accounting. Flame atomic absorption spectrophotometry (FAAS) has been the work horse of the assay lab for this duty for decades. In 1994 the FAAS standard method was approved by the American Society for Testing and Materials (ASTM) (1). Six process solutions were collected and preserved by measuring the pH and adjusting to greater than pH 10, if necessary. Duplicate solutions were provided to eight laboratories in random order for analysis by FAAS covering the gold concentration range of 0.19 µg/mL (0.006 toz/t.) to 10.7 µg/mL (0.312 toz/t). A high precision method was used, which involved bracketing the sample with the higher and lower standards nearest to its concentration repeating readings three times and averaging the results. The optimum precision for the FAAS gold method was found to be at the 1.00 µg/mL (0.029 toz/t) and lower scope limit 0.3 µg/mL (0.009 toz/t) gold concentration. Since tailings solutions typically have concentrations below the lower scope limit, use of ICPMS was developed at Newmont USA Limited (Newmont) to assay the lower range solutions."

Jan 1, 2016

By Jerry C. Tien

China?s remarkable levels of economic growth during the past three decades have lifted almost 300 million people out of poverty. This amazing achievement has placed an increasing demand on energy and minerals, especially coal, which supplies 68.7 percent of China?s energy (June 2011). It is estimated that China mined more than 3 Gt (3.3 billion st) of coal in 2010, three times as much when compared to merely 10 years earlier. Such an impressive achievement does not come without major costs ?? including concerns with mine safety and an increasing number of occupational illnesses due to fast growth. This article reports on one of the major safety concerns in China?s coal mining, dust and dust control practices, and known cases of caol worker?s pneumoconiosis affiliated with prolonged exposure to excessive coal dusts. The exact size of China?s mining industry is not known, but it is estimated the coal industry is at least five-million people strong, and the metal and nonmetals industry probably employs another three million people. To meet increasing energy demand, China mined more than 3.1 Gt (3.4 billion st) of coal in 2010 from its 15,000 plus coal operations1, most of which are small- to medium-sized operations with annual coal productions ranging from a few thousand tons to 300 kt (330,000 st). These small coal operations are typically in remote areas, inadequately engineered, poorly ventilated and still using rudimentary drilling and blasting mining methods employing antiquated mining equipment and, presenting safety concerns, i.e., methane and dust explosions.

Jan 1, 2011

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

9.1 INTRODUCTION There are approximately 70,000 abandoned coal mines nation¬wide, which is about 35 times the number of underground coal mines presently operating. The US Bureau of Mines estimates that there are over 8 million acres of undermined land due to the extraction of coal, metals, and nonmetals. Subsidence has affected more than 2 million acres, and more than 99% of the subsidence is related to underground coal mining. There is reason to believe that some of the remaining 6 million acres of the undermined land have a high potential to subside. The expansion of housing, highways, commercial structures, and other facilities has required the use of many areas that are underlain by abandoned coal mines, and this growth will continue. Many subsidence problems are derived from the collapse of aban¬doned underground coal mines. There are numerous abandoned mine workings in the anthracite fields of northeastern Pennsylva¬nia, in the Appalachian bituminous fields, the Illinois Basin, the Rock Springs, Wyoming area, and other areas of the United States (Gray et al., 1976). Various room and pillar patterns of mining have been used in the dipping anthracite seams and the nearly flat-lying bituminous seams with considerable variation in the per¬centage of coal extracted. The progressive deterioration of pillars, mine floors, and mine roofs after long exposure to air and water may later result in the collapse of strata over the mine entries, the crushing of the remaining coal pillars, or the bearing failure of the mine floor beneath the coal pillars. Subsidence then results as the collapse reaches the ground surface in the form of differential strains, depressions, cracking of the ground, and sinkhole devel¬opment. Subsidence over active longwall mines, which occurs concurrently with mining or is completed within a short period following coal extraction, has been studied extensively over the past decade. On the other hand, subsidence over abandoned coal mines receives little attention by the researchers, mainly because it is difficult to predict and takes place decades after mining has ceased. The techniques of investigating the subsidence events over abandoned coal mines are similar to those employed for active mines except that at the outset, it is necessary to determine whether or not the subsidence events are mining-related (Chugh et al., 1986; Cummings and Singh, 1986; Peng and Hsiung, 1986). This calls for the identification and confirmation of abandoned mine workings under or near the affected surface structures. Gen¬erally old mine maps, if available, are acquired, the surface bore¬holes are drilled for confirmation of the accuracy of the mine maps and determination of the potential for continued subsidence. Sub¬sidence monuments are established and periodic surveys con¬ducted to determine the amount and trends of surface movement in and around the affected surface structures; surface boreholes are used to investigate the integrity of the underground structures (i.e., roof, coal pillars, and floor) by TV camera. They are also used for monitoring the vertical and horizontal movements of the subsur¬face strata by Sondex (FPBX) and inclinometer (PFBI), respec¬tively, for determining the continuity of the subsidence events. Tape extensometers, crackmeters, etc., are used to monitor the development trends of major cracks in the structures or on the ground. These data are used to identify the causes of the subsidence events. Finally, abatement methods are selected to stabilize the structures. It must be noted that most subsidence events over abandoned coal mines are reported after the fact, and investiga¬tions are begun some time after reporting, that the subsequent measured movements are generally much smaller than that at¬tained in the active mines, and that due to lack of knowledge about the damage conditions and the exact location of the abandoned mine workings with respect to the affected surface structures, the precise causes of surface subsidence or surface structural damages are in most cases very difficult to identify. 9.2 TYPES OF SURFACE SUBSIDENCE According to Gray et al. (1977), after examining 354 incidents of subsidence above abandoned mines in the Pittsburgh metropol¬itan area, the subsidence features have a mean diameter (i.e. the average of long and short dimensions) from less than 1 ft to 1600 ft, with 84% less than or equal to 15 ft; the subsidence features have a depth ranging from less than 1 ft to 48 ft, with 89% less than 25 ft; 66% of the subsidence features are deeper than they are broad. Nearly 59% of the subsidence features occur with overbur¬den less than 50 ft thick and 81% less than 100 ft thick. No subsidence features occur with overburden thicker than 450 ft (Fig. 9.1). Occurrence of subsidence incidents varies from imme¬diately to more than 100 years after mining (Fig. 9.2). In analyzing the characteristics of approximately 3000 chim¬ney subsidence features along the Colorado Front Range, Matheson and Eckert-Clift (1986) examined historical aerial photographs on 4- to 14-year intervals between 1937 and 1967 and found that the majority of observable surface subsidence features occurred within 30 to 40 years after mining. According to Gray et al. (1977), the most prevalent subsi¬dence features over abandoned mined land are sinkholes, with depths of more than 3 ft, and troughs or sags, usually less than 3 ft deep. Sinkholes are steep-sided pits, while troughs are shallow depressions much wider in area than sinkholes. A. SINKHOLE SUBSIDENCE A sinkhole is caused by the collapse of a mine roof that works its way upward. If it is not arrested during the process it will eventually reach the surface and emerge as a sinkhole. The process is governed by the thickness and character of the overburden, the width and height of the mine openings. Sinkholes are usually 3 to 20 ft deep and may be 2 to 40 ft in diameter, although most are fewer than 16 ft across (Gray et al., 1977; DuMontelle and Bauer, 1983). Newly formed sinkholes have steep sides with straight or bell-shaped walls. At times, they appear to be conical in profile with the apex upward. If the topsoil collapses, the top portion will widen to form an hour-glass shape. Sinkhole subsidence usually occurs over abandoned mines less than 165 ft deep (Hunt, 1979). Matheson and Eckert-Clift (1986) found that chimney sink¬holes are likely to occur when the ratio of overburden thickness to mining height (h/m) is less than 4 to 5. When h/m is between 5 and 10 to 11, the potential occurrence of chimney sinkholes decreases rapidly. When h/m is more than 10 to 11, less than 10% of the mine openings that collapse will induce sinkholes on the surface.

Jan 1, 1992