Search Documents

By G. S. S. Raman, M. S. Klima

The effects of pressure and cake thickness were studied using a split-plot design for pressure filtration of a fine refuse slurry obtained from a bituminous coal preparation facility. Pressure filtration offers the potential to significantly reduce the moisture content of the fine refuse stream with the addition of little to no flocculants, thereby minimizing the volume of refuse stored in impoundments and providing a recycle water stream for use within the plant. Experimental results showed that the final cake moisture decreased with increase in pressure and decrease in cake thickness. In addition, specific cake resistances calculated for the various tests indicated an increasing trend with increasing pressure and decreasing cake thickness. With increase in cake thickness, an increase in cake moisture and the weight of solids deposited in the cake was observed. An ANOVA analysis indicated that both cake thickness and pressure significantly affected the cake moisture, while only cake thickness statistically influenced the weight of solids in the cake. A regression model was developed with an R2 value of about 0.99 to relate cake thickness, the single largest statistically significant factor, with the weight of solids in the cake. Filter capacities were calculated in terms of the solids deposited per unit time based on a product specification of 25 percent cake moisture, and it was observed that the thinnest cake had the highest filter capacity.

By S. Dixon

The Peñasquito deposit in Mexico is one of the largest grassroots precious metal discoveries to be developed in recent years Minera Peñasquito, S.A. de C.V., a wholly owned subsidiary of Goldcorp Inc. has developed the Peñasquito property to produce an average annual production of 120 kilo tonnes of lead containing 0.5 million oz gold and 30 million oz silver and 250 kilo tonnes of zinc containing 20 thousand oz gold and 1.5 million oz silver.. The Peñasquito property covers a 39,000 hectare area in the western half of the Concepción del Oro district in the northeast corner of Zacatecas State, Mexico, approximately 24°45'N latitude/101°30'W longitude. The sulfide reserves are 1,009 million tonnes containing 3.33 million tonnes of lead, 7.26 million tonnes of zinc, 16.5 million ounces of gold and 1,000 million ounces of silver. This paper describes the work to justify the installation of HPGR to process the crushed SAG mill pebbles. The SAG mill-Ball mill and Cone crusher (SABC) grinding circuit is an accepted grinding circuit to optimize power consumption relative to throughput. The installation of a HPGR to process the Cone crusher product is the next step in optimizing the power consumption relative to throughput. The concern expressed by some on not moving on this change in grinding circuit was the capital and operating cost of a HPGR. The pebbles from the SAG mill can be the more abrasive and are the harder particles of the ore. Goldcorp investigated the wear and processing costs of installing a HPGR to treat the crushed pebbles. The conclusion was the installation would be a very positive economic factor in the operation of Peñasquito. This is the first application of the use of HPGR to process crushed pebbles. Minera Peñasquito and M3 Engineering selected Polysius to provide a Polycom 2417 with twin 3,000 kW drives. A comprehensive test program at Polysius has shown for 7% higher circuit power it is possible to get approx 23% higher tonnage. This coupled with full utilization of the SAG and Ball Mill available energies and with proper control of the transfer size from the SAG to Ball mill circuit there is the potential to achieve 65,000 mtpd per line or a 30% total capacity increase. The cost of power for this increase in grinding capacity is 4.8 kWh/tonne.

Jan 1, 2010

By B. J. Arnold, F. F. Aplan

A model incorporating rate and residence time to describe the froth flotation process was used to provide data for the evaluation of various kinetic flotation models and to provide scale-up information from laboratory to industrial scale coal froth flotation. Rate constants were determined in laboratory and plant froth flotation tests and the residence time distribution was measured for a bank of four 21 ft 3 (0.6 m3 ) WEMCO cells treating Upper Freeport seam coal and a bank of four 300 ft 3 (8.5 m3 ) cells treating Lower Kittanning seam coal. It was found that a lag time for continuous flotation should be incorporated into scale up models and that a kinetic froth factor ratio of between about 2.0 and 2.8 should also be used to scale up data from laboratory to plant scale.

Jan 1, 1989

By Margaret Armstrong

The increasing cost of developing new mines and the need to mine more marginal deposits have led mining companies to use more sophisticated estimation methods such as kriging. But until recently, coal mining companies have shown little or no interest in these techniques. However, the stringent quality controls which are now placed on coal have led to a surge in interest in improved estimation methods. This can be seen from the -, number of research projects by private companies and governmental agencies on the application of geostatistics to coal reserve estimation. At present, most of these programs are centered on the problem of estimating the tonnage and the average grade (i.e. ash percent, sulphur content, calorific value, etc.) of the coal in-situ. See, for example, Sabourin (1975), Woods (1976, 1979), Pauncz and Nixon (1979) and Armstrong (1980). These studies show that the established techniques of linear geostatistics can be applied successfully to coal deposits. The study by Woods is particularly interesting because he had access to the actual production figures as well as the initial sample data from the no 2 seam in the Greenside Colliery owned by the Anglo-American Corporation. He showed that the estimates obtained by kriging were consistently closer to the actual production figures than those given by three other estimation methods. This confirms the superiority of kriging as a method of estimating block values for coal. Another advantage of geostatistics is that it can be used to determine the optimal spacing between drill holes. An example of this is given by Armstrong for the coking coal deposit in the Bowen Basin, Australia.

Jan 1, 1981

By V. K. Reddy Kallam, NEHA PANDEY, Sunil Kumar Tripathy, ARIJIT BISWAS

The study investigates SO2 leaching of low-grade ferruginous manganese ores to selectively recover manganese as MnSO4 and produce battery-grade electrolytic manganese dioxide (EMD). The effects of leaching parameters (duration, temperature, SO2 flow rate) on Mn recovery were studied. Under optimum conditions, 97.9% Mn recovery was achieved. The MnSO4 leach liquor was purified and used for electrowinning EMD with 88.01% purity and battery-active γ structure.

Apr 20, 2022

By P. T. Bissert, T. J. Lutz, J. A. Yonkey, G. T. Homce

"The U.S. National Institute for Occupational Safety and Health (NIOSH) has been researching refuge alternatives (RAs) since 2007. RAs typically have built-in pressure relief valves (PRVs) to prevent the unit from reaching unsafe pressures. The U.S. Mine Safety and Health Administration requires that these valves vent the chamber at a maximum pressure of 1.25 kPa (0.18 psi, 5.0 in. H2O), or as specified by the manufacturer, above mine atmospheric pressure in the RA. To facilitate PRV testing, an instrumented benchtop test fixture was developed using an off-the-shelf centrifugal blower and ductwork. Relief pressures and flow characteristics were measured for three units: (1) a modified polyvinyl chloride check valve, (2) an off-the-shelf brass/cast-iron butterfly check valve and (3) a commercially available valve that was designed specifically for one manufacturer’s steel prefabricated RAs and had been adapted for use in one mine operator’s built-in-place RA. PRVs used in tent-style RAs were not investigated. The units were tested with different modifications and configurations in order to check compliance with Title 30 Code of Federal Regulations, or 30 CFR, regulations. The commercially available relief valve did not meet the 30 CFR relief pressure specification but may meet the manufacturer’s specification. Alternative valve designs were modified to meet the 30 CFR relief pressure specification, but all valve designs will need further design research to examine survivability in the event of a 103 kPa (15.0 psi) impulse overpressure during a disaster. BackgroundThe Mine Improvement and New Emergency Response Act of 2006, known as the Miner Act (U.S. Department of Labor, 2006), was enacted in the wake of three mine accidents involving explosions or fire that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the Miner Act includes provisions that target mine safety issues in areas such as emergency response planning; adoption of new technology; training and education; and mine safety standards enforcement. Section 13 of the Miner Act specifically directed the U.S. National Institute for Occupational Safety and Health (NIOSH) to provide for research into the effectiveness and viability of refuge alternatives (RAs) for underground coal mines, and the U.S. Department of Labor to act on the results of such research, as appropriate. These mandates culminated in the 2009 adoption of changes to the Title 30 Code of Federal Regulations, or 30 CFR, mining health and safety regulations (U.S. Department of Labor, 2008), requiring underground coal mines to supply mine emergency RAs and associated components so as to provide a life-sustaining environment for persons trapped underground. Such RAs can be either selfcontained mobile units or built-in-place facilities. The regulatory changes also include provisions establishing requirements for the approval of RAs and their components by the U.S. Mine Safety and Health Administration (MSHA), among which are numerous criteria for providing a safe breathable atmosphere under positive pressure within the RAs. One criterion for maintaining a safe RA atmosphere is the inclusion of an air pressure relief valve that will activate at a maximum of 1.25 kPa (specified as 0.18 psi, or approximately 5.0 in. H2O), or as specified by the RA manufacturer, above mine atmospheric pressure in the RA (U.S. Department of Labor, 2008)."

Oct 1, 2016

By Milan Lipensky

This paper discusses the longwalling practices used at the San. Francisco Mine of Compania Minera Autlan in Mexico, in. the mining of a sedimentary, manganese deposit. Bethlehem. Steel Company is a part owner of this property. The San. Francisco Mine is located approximately 580 miles west of Mexico City, on the outskirts of the town of Autlan, in the State of Jalisco. The ore is shipped from the port of Manzanillo 120 miles southwest of Autlan. The mining method is a variation of the longwall retreat system, using friction. props that, until recently, had been used only in coal mining operations of Europe and the United States. However, due to the structure of the ore body and the modified longwall system that is practiced, there exists some unusual variations, such as: .1) friction props set by a mechanical two-step lifting device, 2) drilling and blasting, against the friction props, 3) a highly fractured and undulating, volcanic tuff roof; 4) displacement faults-up to 5 meters, and 5) a relatively stable, irregular floor.

Jan 1, 1964

By BHAMIDIPATI S. SASTRY, ANMAYA NAIK, ASIF AHMAD, Srivatsan Jayaraman Sridharan, ADITYA PANDEY

Wet kata cooling power (WKCP) as measured by a kata thermometer is a well-known heat stress index used in the mining industry. Although, over the years, several researchers proposed different heat indices and indicated limitations of the kata thermometer, WKCP is used in the South African gold mining industry due to its simplicity and rapidity of assessment. This paper presents a comparative analysis of the newly developed empirical expression for the WKCP and some of the more commonly used empirical models. For this purpose, WKCP measurements are obtained based on experiments conducted in a low-speed wind tunnel. Based on a regression technique, the analysis presented aims to assess the disagreement between the empirical model predictions and actual measurements. The correlation is also presented between WKCP and the well-established thermoregulation models using parameters from the low-speed wind tunnel experiments, including dry-bulb temperature (Td), wet-bulb temperature (Tw), barometric pressure (P), and wind speed (v). It is found that the proposed empirical model for the WKCP represents the bioclimatic interaction quite well under the specific parameters that defines the harsh thermal environment and air condition, such as metabolic activity, clothing of the person, and the velocity of the ventilating air in which the person is working. The statistical analyses performed show that the empirical model proposed for the WKCP produces satisfactory estimates of the thermal stress experienced under lower air velocities, light clothing, and higher metabolic activity rates.

Sep 2, 2021

By A. Lashgari, V. Kecojevic

This paper presents research on the environmental impact of digging and loading equipment used in surface coal mining. Environmental impact was assessed through the measurement of equipment exhaust and dust emissions, and sound level. In this study, exhaust emission refers to carbon dioxide (CO2), carbon monoxide (CO), nitrogen oxides (NOx), sulfur oxides (SOx) and volatile organic compounds (VOCs). Dust generation refers to fine particles (PM2.5), inhalable particles (PM10) and total suspended particulate matter (TSP). Sound level refers to the sound pressure level at different distances from the equipment. Modeling of the environmental impact of digging and loading equipment was conducted using the Microsoft Visual Studio.NET software package. This research was a part of a broader project involving the development of a software system for the selection of productive, cost-efficient and ecofriendly mining systems, sponsored by the Appalachian Research Initiatives for Environmental Sciences (ARIES). This research may assist mining professionals in quantifying the environmental impact of digging and loading equipment, and developing strategies for reducing the overall impact of such equipment in surface mining.

Jan 1, 2013

By Sidi Deng, Sharon Pedraza, Aaron Noble, Subodh Das, Bin Ji, Wencai Zhang, Michael Van Brunt

In this study, a MSWI bottom ash sample was assessed to evaluate the feasibility of various physical beneficiation processes in concentrating valuable elements prior to chemical leaching. The raw sample was initially assayed to determine the content and economic value of various metals present in the material. The potential recoverable value (PRV) of the sample was calculated, and the result showed that the total PRV of the sample was 483 $/ton, with Ti, Sc, Fe, Cu, and Zn being the most valuable metals. Next, various physical separation processes, including size fractionation, froth flotation, magnetic separation, and gravity separation, were conducted to determine the extent to which the valuable elements can be concentrated. The results were compiled into an element-by-beneficiation enrichment ratio (er) matrix that was used to develop suitable beneficiation flowsheets for further consideration. The result clearly show delineation of four products, including a Fe-rich product that can be isolated by magnetic separation (er = 5.0), a Cu/Zn-rich product that can be isolated by flotation (er = 5.3 to 9.4), a Sc-rich product that can be isolated by gravity separation (er = 0.6), and a Ti–rich product that is produced in the residue. Lastly, the leachability of valuable elements from the bottom ash sample was determined by acid leaching tests. The results indicated that it is viable to employ hydrometallurgical methods to recover and purify the valuable metals. This work provides a reference for the recovery of valuable metals from MSWI bottom ash from both the technical and economic aspects.

Apr 27, 2024

By CORA ROELOFS

In the USA, miners are at higher risk for work-related disorders that could precipitate an opioid prescription, injury-related opioid prescriptions, and opioid overdose. We aimed to support prevention of these outcomes with an “opioid hazard awareness” miner safety training module. In January and February 2020, the training module was embedded within required mining safety and health training for stone, sand, and gravel miners in Massachusetts (USA). Training impact and reception were assessed with a pre- and post-training survey of trainee characteristics, training content knowledge, and attitudes. Over 800 miners were trained and over 600 responded to surveys. We found statistically significant improvements in opioid risk factor knowledge and knowledge of resources to help a coworker. Nonstigmatizing attitudes were high both at baseline and following the training. The training was perceived as relevant and useful by trainees. Improving opioid hazard awareness in high-risk worker populations has potential to reduce opioid dependence and downstream impacts including overdose death. Employer injury-prevention efforts should be reinforced while worker health and safety training enhances awareness of opioid-related harms and prevention strategies for miners and other high-risk worker populations.

Nov 19, 2021

By K. Yatsunami

NKK has developed a new cold bonded pellet process. The features of this process are; 1) it is a continuous process with 10 hours curing. 2) Products can be used as materials for various metallurgical furnaces. 3) Various kinds of slag are used as binders if necessary. 4) The quality of products is excellent. The pilot plant completed in 1981 is now being successfully operated. We are also constructing a commercial plant at our Niigata works. We produced cold pellets containing carbon as material for ferroalloys (Si-Mn), by pilot plant and used them in furnaces. Consequently, considerable economic advantages were obtained.

Jan 1, 1984

By Carl-Henrik Knudsen, Rolf Tore Arnesen, Eigil R. Iversen

Recovery of iron and copper from acid mine drainage was studied in pilot scale at a continuous treatment plant at the mine site of the King's mine in Roeros, Norway. The average load on the plant was 1 m3/h. The process tested in this project is a three-step process consisting of: 1) Fe(OH)3 precipitation at pH 3.5, dewatering of iron sludge and transport to ferric chloride plant; 2) after filtration precipitation of residual metals at pH 9, concentration of metal sludge by flotation; 3) extraction of metals from the sludge with sulphuric acid followed by recovery of copper by electrolysis. The copper could be used for local production of different crafts, but this condition needs a further evaluation. The process economy at a full scale plant is evaluated.

Jan 1, 2000

By T. Gouri Charan

Indian coals, which are of Gondwana origin, contain high amounts of mineral matter, wherein the extraneous material was intimately mixed in the coal matrix during the formation stage, causing a high level of impurity in the run-of-mine (ROM) material. These coals possess difficult to very difficult washability characteristics. Beneficiation of high-ash non-coking coals of India has become the prerequisite for improving the overall economics and efficiency of power generation. The use of dry cleaning systems in India for beneficiation of non-coking coals has gaining renewed interest recently. The benefit of the dry beneficiation process is to exploit the given resources while providing a more reliable and consistent quality fuel with a low operating cost. M/S Allmineral has introduced a technique for the dry beneficiation of coal, which is being tried in India for the treatment of high-ash non-coking coals. The first commercial air jig of 50 t/hr capacity was installed and commissioned to beneficiate high-ash coals of 40 x 5 mm feed with an ash content of 40%; a clean coal product of 33% ash was produced and is being used for a sponge iron plant.

Jan 1, 2011

By R. K. Amankwah, E. K. Asiam

Changes in the thermal-oxidation behavior and other properties of gold-bearing waste activated carbon when milled in both a ball mill and a vibratory mill were investigated. It was found that significant changes occurred in the oxidation temperature of the vibration-milled waste carbon as a result of increases in surface area and mechano-chemical activation. The mechano-chemical action brought about modifications in the crystal structure of the waste carbon. As a result, the vibration-milled sample was completely oxidized at a temperature of 450°C. Thus, the study established that vibration milling is a better way of lowering the temperature of oxidation of the waste carbon. Furthermore, the gold was found to be concentrated in the ash and, when leached with cyanide for 20 hrs, the gold recoveries from a sample having a head grade of 2 kg/t was 99.5% for the vibration-milled sample and 82% for the ball-milled sample. The lower gold recovery for the ball-milled sample was attributed to sintering of the ash, which was caused by the higher temperature required for its oxidation.

Jan 1, 1997

By M. Churchill, V. R. Degner

Over the past two decades, declining ore body grades and increased operating and construction costs have provided an incentive for the development of progressively larger flotation machines. As a result, the 1.7-2.8 m3 (60-100 cu ft) flotation machine of the 1950's and 1960's is being rapidly replaced by large volume machines. The result has been improved flotation machine specific capacity (tph processed per sq ft of floor space); specific power (hp per tph processed); and process control simplicity. The recent development and satisfactory plant evaluation of the 28 m3 (1000 cu ft) flotation machine allows economic and operating advantages in high tonnage mill applications. Some principles of mechanically induced air flotation and the development of the large 28.3 m3 (1000 cu ft) flotation machine are reviewed here. Performance evaluation in beneficiating metalliferous ores-copper, zinc, and iron-is also given and recently completed plant results provided. Mining lower grade ore bodies results in the need to process increased tonnage in the concentrator. This greater tonnage requires more individual flotation machines, unless individual machine capacity, or cell volume, is increased. As the ore processing rate of the concentrator increases, the benefits of progressively larger individual cells in the flotation section become more significant. The accompanying figure illustrates the advantages of a larger flotation machine. In the figure, the number of machines in the rougher-scavenger section is related to the plant tonnage for three sizes of flotation machine: 8.5 m3 (300 cu ft), 14.2 m3 (500 cu ft), 28.3 m3 (1000 cu ft). The 28.3 m3 (1000 cu ft) flotation machine results in 95 fewer machines, compared to the 8.5 m3 (300 cu ft) machine at 45.4 kt/d (50,000 stpd) feed. The flotation cell reduction is, of course, doubled at a plant production rate of 90.7 kt/d (100,000 stpd). Using fewer flotation machines saves floor space. The 14.2 m3 (500 cu ft) and the 28.3 m3 (1000 cu ft) machines result in a floor area reduction, relative to the 8.5 (300 cu ft) machine requirements, of 134.7 and 418.1 m2 (1450 and 4500 sq ft), respectively, for the 45.4 kt/d (50,000 stpd) rate and 269.4 and 836.1 m2 (2900 and 9000 sq ft), respectively, for the 90.7 kt/d (100,000 stpd) rate. In addition, flotation practice has shown that the "specific power intensity"-power per unit cell volume-is less for increased cell size. This results in a power draw reduction, for the rougher-scavenger circuit, of between 552 and 686 kW (740 and 920 hp) for the 14.2 and 28.3 m3 (500 and 1000 cu ft) machines, respectively, when processing 90.7 kt/d (100,000 stpd). Fewer cells improve machine control and simplify maintenance needs while reducing floor space and power requirements. These are tangible incentives for the development of large flotation machines for high tonnage applications. Flotation Principles The accompanying figure shows how key hydrodynamic regions influence the performance of a mechanically induced air flotation machine. Air is induced into the fluid from the top of the cell, due to the mechanical action of a rotating impeller. The impeller circulates the liquid, or pulp, from the bottom of the cell. The result of these dual flow paths is the mixing of the two fluids and one solid phase in the highly agitated region where physical contact between the air bubbles, and the solid particles to be floated, is accomplished. The particle to be floated is assumed to have a properly prepared hydrophobic surface prior to flotation. Upon leaving the three-phase mixing region, the "floatable particle-air bubble matrix" and

Jan 7, 1982

By Alexander Sutulov

It is calculated that since the beginning of last century, which practically coincides with the beginning of the Industrial Revolution, our civilization has consumed around 239.5 million tons of copper (see: Table 1). According to the most pessimistic projections of today, with only a 2.5% annual growth rate in demand, we are bound until the end of this century to consume another 200 million tons of copper in remaining 17 years. A recent study made by US Bureau of Mines (1) indicates that the proven ore reserves of 150 major operating mines and about 120 deposits sufficiently explored for development and feasibility studies accumulate a total mass of 49.3 billion tons of ore, assaying an average of 0.82% Cu and containing around 324 million tons of recoverable copper. Consequently, there is a high grade of probability that the bulk of our future ore supplies, for our demand of, say, next 25 years will cane precisely from these mines. The interesting point in USBM study is that it indicates the recoverable byproduct content of these ores and which is: 118.2 million troy ounces of gold 2277.4 million troy ounces of silver 7.1 million tons of lead 24.7 million tons of zinc 1.3 million tons of nickel 3.1 million tons of molybdenum 765 thousand tons of cobalt, and 720 thousand troy ounces of platinum. This information gives us a relatively reliable profile of our future ores for next 25 years, and thus makes possible evaluation of byproduct credits in our future copper mining and producing activities.

Jan 1, 1983

By Lawrence K. Nordell

The selection of belt conveyor drive systems (*) is the subject of ongoing investigation. Frequently this choice has been governed by an incomplete perspective on the major considerations. A more comprehensive and objective approach is desirable. This paper presents additional factors which hopefully will broaden this perspective. BACKGROUND Conventional belt conveyors are powered by electric or electro-mechanical drives(*) mounted at the conveyor's head, tail, intermediate return span, or a combination of these (Fig. 1). A list of the drives reviewed is given in Table I. The following are main elements influencing the selection of the drive system: 1) dynamic characteristics, 2) economic factors such as capital cost, plant spares compatibility, reliability, availability, maintainability, and 3) environmental constraints. The principal dynamic characteristics of concern are the reactions of belt forces generated by the drive system during starting of the conveyor. Another attribute for consideration is the application of multiple driven pulleys used to 1) lower the conveyor's belt tension requirements, 2) increase the expected tonnage throughput, allowing for possible drive component failures, and 3) increase the plant spares flexibility related to the drive assembly.

Jan 1, 1977

By Drew A. Meyer

Magnetic metals are the granddaddy of products which may be recovered from municipal waste. Aside from hand-picking of newsprint and corrugated boxes, magnetic metals are usually the first items a resource recovery facility considers extracting from the solid waste stream. Magnetic metals from incinerator residues and from municipally mandated source segregation programs were first used in significant quantities by the Copper Industry. The ability of the Copper Industry to consume metals from the municipal solid waste stream raised everyone's hopes that there would be more markets for municipal scrap when more of it became available. Somehow something has gone wrong. It is widely acclaimed that scrap is an environmentally sound and economical source of iron. It is greatly in demand for Its contained energy. The prices that the steel industry has been willing to pay for the scrap during the past year are all the proof anyone should need that scrap Is desirable and sought after. But the very fact that I'm speaking today on the markets for magnetic metals recovered from municipal waste indicates that something Is wrong. Clearly the problem is not that we do not need the scrap. The problem is we have not produced the kind of scrap that consumers are willing to buy - either through ignorance of what the consumers wanted or through a conviction that ferrous scrap is so obviously a good thing somebody will surely want it no matter what. Dr. Harvey Alter of the National Center for Resource Recovery has said "You can't sell garbage". In a sense that is only partly true. It really should be "You can't sell garbage for very long". The Steel Companies, in an effort to prove that steel is an environmentally desirable packaging medium, have bought some scrap that can only be described as garbage. They are to be commended for doing so. The fault lies not with the Steel Company for taking and paying for "garbage" but with the producer of that poorly prepared scrap. Far every instance where the steel industry has purchased the often undesirable product from resource recovery facility there are several magnetic installations sitting Idle because someone forgot the most essential part of producing the magnetic product - selling it to someone.

Jan 1, 1975

By Yingbao Yang, Jinyue Liu, Yonggang Wei, Bo Li

Due to the depletion of copper ore with high-grade and low impurity contents, the raw materials for copper smelting exhibit low copper contents and high impurities. High-impurity elements lead to the poor performance of the final copper product; thus, the removal of impurity elements during the oxygen-enriched copper smelting process is crucial. In this study, based on the production of high-grade matte, the occurrence states of impurity elements (such as As, Pb, and Zn) are analyzed in the input and output materials of the oxygen-enriched smelting process, and the phase transformation mechanisms of impurity elements are revealed during the oxygen-enriched smelting process. The effects of temperature, Fe/SiO2 ratio and oxygen concentration on the distribution behaviors of impurity elements in dust, slag and matte and the removal rates of impurity elements in matte are clarified. The results show that the impurity elements mainly exist as As4, As4S4, As2O3, Pb, PbS, PbO, Zn and ZnS in dust, as FeAsO4, As2O3, FeAsS, PbSiO3, Zn2SiO4 and ZnFe2O4 in slag, and as As, FeAsS, PbS, PbO and ZnS in matte. High smelting temperature, low Fe/SiO2 ratio and low oxygen concentration are beneficial for improving the matte grade and the removal rates of impurity elements Pb and Zn in matte. Low smelting temperature, low Fe/SiO2 ratio and high oxygen concentration are beneficial for removing impurity element As in matte.

Aug 8, 2023