Search Documents

By Denis Tepavac, Mark Trim

Structural performance of fiber reinforced concrete (FRC) depends on its ability to carry tensile forces after cracking. Australian Standards AS5100-2017 and AS3600-2018 are the only available design standards that establish a test procedure to determine strength and toughness of an FRC in direct tension. Direct tensile testing of fiber reinforced shotcrete samples was performed to determine if the model and guidelines in AS5100/3600 were applicable to shotcrete; all previous testing was from cast samples. In addition to direct testing, micro CT-scanning was also performed. The paper presents tests performed, results, and how the tests could be used on future projects. In addition, a brief summary is provided of the guiding structural mechanics used for estimating residual tensile strength and test methods utilized to verify those estimates.

Jun 13, 2023

By Angelina Anani, Nilufer K. B. Akbulut, Sefiu O. Adewuyi

Crucial information about safety, design, and operation can be utilized in underground mines from ground movement data. Communicating the information and exploring new findings can be a challenge in a decade where there is an ever-increasing volume and velocity of data due to advancements in mining technologies. This challenge escalates for geotechnical data as it is multidimensional, depending on the space and the rate it takes place. To tackle this challenge, geotechnical engineers should focus on utilizing simple yet compelling visualization of rock mass data in 3D. Competent visualizations of ground conditions as a Trigger Action and Response Plan (TARP) could ease the communication of safety concerns and the exploration of rock mass displacement and strain surrounding an opening at an underground mine. Therefore, this study focuses on using scientific visualization methods by rendering geotechnical data over the surface of a 3D mesh model to display TARP levels. The study is conducted at the San Xavier (SX) Underground Mine Laboratory’s East decline. The project aims to produce visualizations that optimize the use of geotechnical data in near-real-time.

Feb 1, 2025

By C. J. Pritchard

The Office of Mine Safety and Health Research (OMSHR) investigated ways to increase mine airflow to underground metal/nonmetal (M/NM) mine working areas to improve miners? health and safety. One of those areas is controlled recirculation. Because the quantity of mine air often cannot be increased, reusing part of the ventilating air can be an effective alternative, if implemented properly, until the capacity of the present system is improved. The additional airflow can be used to provide effective dilution of contaminants and higher flow velocities in the underground mine environment. Most applications of controlled recirculation involve taking a portion of the return air and passing it back into the intake to increase the air volume delivered to the desired work areas. OMSHR investigated a Nevada gold mine where shaft rehabilitation was in progress and one of the two main fans was shut down to allow reduced air velocity for safe shaft work. Underground booster fan operating pressures were kept constant to maintain airflow to work areas, inducing controlled recirculation in one work zone. Investigation into system behavior and the effects of recirculation on the working area during times of reduced primary ventilation system airflow would provide additional information on implementation of controlled recirculation into the system and how these events affect M/NM ventilation systems. The National Institute for Occupational Safety and Health monitored the ventilation district when both main fans were operating and another scenario with one of the units turned off for maintenance. Airflow and contaminants were measured to determine the exposure effects of induced recirculation on miner health. Surveys showed that 19% controlled recirculation created no change in the overall district airflow distribution and a small reduction in district fresh air intake. Total dust levels increased only modestly and respirable dust levels were also low. Diesel particulate matter (DPM) levels showed a high increase in district intake mass flow, but minor increases in exposure levels related to the recirculation percentage. Utilization of DPM mass flow rates allows input into ventilation modeling programs to better understand and plan for ventilation changes and district recirculation effects on miners? health.

By Margreth Tadie, Chalwe Chibwe

Physicochemical properties of copper electrolytes are a strong fundamental consideration in electrodeposition processes during electro-purification and recovery of copper. Their influence extends to mass transfer as well as energy consumption during the electrodeposition process. In this study, the influence of electrolyte composition on electrolyte physicochemical properties was investigated to review the existing literature data. This review of data is considered necessary as more and more electrowinning models are being developed for process prediction and optimisation and a need of such data is required for accurate prediction of physicochemical properties. The major components of importance to the formation of smooth high-quality and high-purity copper cathodes at optimum current efficiency are considered the species in solution. These include Cu ions, Fe ions (major impurity), H2SO4, and a smoothing agent additive. A 5-factor, 2- and 3-level experimental design was employed to determine the effect of copper (35 and 45 g/l), sulphuric acid (160 and 180 g/l), iron (1, 3, and 6 g/l), polyacrylamide additive (2, 5, and 10 mg/ l), and temperature (45 and 55 °C) on electrolyte density, conductivity, and the diffusion coefficient in synthetic copper electrowinning electrolytes. The major species in a copper electrowinning electrolyte are found to be the most relevant for prediction of physicochemical properties. These results indicate that relatively simple empirical models are sufficient for modelling of the electrolyte domain in electrowinning, without the need for the generation of vast amounts of complex experimental data.

Feb 1, 2021

By Juan L. Sepulveda

An MPSI KW-20 Tower mill has been tested at the Butte Molybdenum plant of Anaconda Minerals Company, as a substitute for the conventional 1.5x3.0 m (5x10 ft) tumbling ball mill currently used for regrind purposes. The Tower mill was operated in both open and closed continuous circuits. These results were complemented with a series of batch grinding tests to determine some of the operational features of this mill. The relative grinding efficiency of the Tower mill with respect to the tumbling ball mill was determined and the applicability of this new mill to a plant/heavy duty environment was assessed. Experimental results obtained on the regrind of moly concentrates indicate that approximately 40% energy savings can be realized by using the Tower mill instead of the ball mill.

Jan 1, 1984

By Louis A. Panek

Using an approach based on the theory of similitude, the author develops a general equation and related concepts that provide new insights to an old problem. The load-bearing capacity (strength) of a square, rectangular, or cylindrical prism of a brittle material such as rock, coal, or concrete is expressed as the mathematical product of a size effect, a shape effect, and a function of the mechanical properties (deformability, cleat/joint spacing, and friction) of the pillar, roof and floor materials. Through an application of multivariate statistical analysis, the results of assorted tests and observations of failed pillars can be combined into a fundamental scaling equation, which provides a unified, consistent approach to the estimation of mine pillar strength. The form of the equation is sufficiently general to be able to incorporate refinements in the characterization of the basis factors, as they become available through future experimentation and analysis.

Jan 1, 1979

By Basak Anameric

This study reports preliminary feasibility investigations for utilization of the selective carbothermic reduction and smelting (SCRS) processing scheme to beneficiate low-grade iron-manganese (Fe-Mn) mineral deposits from MN, USA. The study includes laboratory-scale demonstrations using an induction furnace and production of various products by manipulation of operational parameters. The products include alternative iron (Alt Fe), high carbon ferromanganese (HC FeMn), alternative silicomanganese (Alt SiMn), and upgraded manganese concentrate (Mn conc). All of these products have commercial value and can be used in various applications as raw materials.

Nov 23, 2020

By R. K. Singhal

A variety of mining equipment is used in the mining of oil sands by surface mining. This includes bucket wheel excavators, draglines, hydraulic shovels and off-highway trucks. This paper examines the existing mining schemes and equipment used Peculiarities of oil sands surface mining and their influence on equipment selection, utilization and mining schemes are described. Recent developments undertaken to improve mine productivity are also dealt with together with some notes on proposed measures to obtain further gains in productivity.

Jan 1, 1985

By Dejan Petrović, Pavle Stojković, Jelena Ivaz, Saša Stojadinović

In spite of the fact that flyrock phenomenon represents the real threat for personnel and machinery, it still remains insufficiently investigated. There are efforts, in the mining community, to explain the causes of flyrock, but the models capable to accurately predict flyrock occurrence and define the flyrock distance still do not exist. This article is an attempt to establish such a predictive model. The model utilized the adaptive nature of artificial neural networks and combined it with the accuracy of numerical modeling of physical phenomena. Necessary data were collected by high-speed camera recordings of actual blasts at three different surface mines and processed for further use for artificial network training. The result was a neuro-numerical couple which was capable to predict flyrock occurrence, estimate the launch velocity of flyrock fragments, and calculate the maximum distance of flyrock fragments. The safe distance was then calculated by multiplying the flyrock distance with a factor of safety. The article explains the procedure for data acquisition and processing, artificial network construction, training, and validation. It also explains the principles of flyrock distance calculation and, finally, provides a definition of factor of safety and safe distance. The results showed that the prediction was satisfactorily accurate and reliable.

Oct 22, 2021

By David A. Zegeer

It's a pleasure to be here, and an honor to be invited to address this distinguished group of professionals. Today, I'd like to begin with an overview of progress in coal mine safety and health. I'll discuss some current areas of concern. And I'll make some suggestions as to where we may be headed in the future. This year marks the coal industry's 15th anniversary under the Coal Mine Safety and Health Act, which took effect in 1970. We have come a long way in those 15 years. As a coal mining man from way back, I remember the era when the Coal Mine Safety and Health Act first was passed. Some of you may remember it, too. At that time, the safety and health of coal miners was in the public eye even more than it is at present. One reason was a mine explosion that killed 78 miners when it occurred in a large underground coal mine in November 1968. That disaster raised tremendous public concern about protecting the safety of miners.

Jan 1, 1985

By Elvin R. Beach, Jaroslaw Drelich

Pull-off forces were measured for 8-9 pm diameter polystyrene (PSI particles on smooth spin- coated polystyrene films and hexadecanethiol (HDT) self-assemble monolayer surfaces using atomic force microscopy (AFM). Three parameters were controlled during experimentation: (i) the maximum applied load pressing the particle onto the substrate was varied from 50 to 4,000 nN, (ii) loading/unloading rate for the particle to attach and separate from the substrate varied from 0.01 to 9.3 Hz, and (iii) contact time for particle to reside on the substrate surface before retracting the particle to separate it from the surface changed from I µsecond to 200 seconds. the pull-off forces increased with increasing applied loading, increasing loading/unloading rate, and increasing contact time for the PS particle on PS film and on HDT monolayer. The PS particles experience elastic and plastic deformations duringpull-08 force measurements. Plastic deformation is primarily associated with flattening of surface irregularities. The results obtained in this research suggest that the particle-substrate contact areas of the magnitude comparable to those predicted by the JKR contact mechanical model can be reached in the AFM experiments by using high applied loads and long particle-substrate contact times. This result re-opens the prospect of' using AFM for studying surface energies of deformable micro-particles, even if the micro-particles have small irregularities on the surface.

Jan 1, 2003

By G. Norman Owen, Roger E. Scholl, Tor L. Brekke

INTRODUCTION Underground structures are generally regarded to be safer than surface structures during strong seismic motion, except when crossing a causative fault. Recent studies of observed earthquake damage to tunnels generally support this view, although instances of severe damage and, occasionally, collapse are reported. For proposed underground construction of sensitive structures such as nuclear power plants, liquefied natural gas facilities, and nuclear waste repositories, a verification of the seismic response of underground structures will be required.. This paper discusses the stabilization recommendations used in a study of additional costs required to protect tunnels against ground motion caused by earthquakes and underground nuclear explosions (1). The study is a part of the site investigations for possible construction of a nuclear waste repository. The additional costs estimated in the study are not presented here; only the stabilization measures are presented in the present paper. The tunnels, which would constitute the underground facilities of a possible repository, are assumed to be 5.5 m (18 ft) in diameter and to be located at a depth of 600 m (2,000 ft). Three candidate geological materials are considered: argillite (shale), granite, and tuff. Several peak ground accelerations are used: 0.3g, 0.5g, and 0.7g for earthquakes, and 0.5g, 0.7g, and 1.0g for underground nuclear explosions. Potential damage due only to shaking is considered here. This paper does not discuss problems that result from creep or sudden rupture of intersected faults or from ground failures at portals.

Jan 1, 1979

By Qingqing Huang, Aaron Noble

The Mineral & Metallurgical Processing Division (MPD) of the Society for Mining, Metallurgy & Exploration held the first MPD Student Video Contest during the spring of 2021. The event showcased the work of 18 graduate and undergraduate students from several U.S. and international institutions. The contest began in January when students submitted a onepage abstract for judging. Over the next several months, they developed a three-minute video that further explained their research findings. Both the abstract and video were evaluated by a panel of judges, and the top-placing participant was recognized at an MPD virtual event held on June 10.

Sep 13, 2021

By J. Marts

Underground longwall coal mining sections are operated as sealed gobs if the coal is prone to spontaneous combustion. Sealing along the gate roads during longwall face retreat limits the flow of fresh air (oxygen) into the gob and, thus, deprives the spontaneous combustion reaction of oxygen. In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines have used computational fluid dynamics modeling to simulate the flow of gases in sealed longwall gobs. The models were validated using measurements and observations from the field and demonstrate that targeted injection of nitrogen along the gate roads inby the face can be used to control the size and location of explosive methane clouds within the gob and to minimize or eliminate the explosion hazard resulting from the formation of flammable methane-air mixtures.

Sep 1, 2013

By R. E. Hucko

The principal thrust of the U.S. Department of Energy (DOE) Coal Preparation R&D Program is to develop technology to reduce the ash and sulfur contents of United States coals to levels such that the resultant product can be formulated into a high quality solid or slurry fuel that could replace oil or natural gas in both new and retrofit applications. Specifically, the objective is to develop and refine cost-effective physical and chemical beneficiation processes to extract 85-95 percent of the total sulfur and ash. The Coal Preparation program is implemented by the Pittsburgh Energy Technology Center (PETC) and is conducted both in-house and by a cross section of industrial organizations, universities, and national laboratories. Research is subdivided into three areas -coal characterization, beneficiation, and ancillary unit operations. This paper will provide a brief overview of many of the research projects being carried out in these areas in fiscal year 1984.

Jan 1, 1984

By R. S. Kalyoncu

Materials demands by the advancing process technologies, desire for higher performance and durability, and improved efficiency in combustion processes, such as applications in heat engines, heat exchanges, and batteries have added to the driving force fueling R&D efforts for the development of components with the combined characteristics of metals and non-metals. These new materials involve refined and specialized microstructures that can lead to improvements in the performance characteristics and durability new technological applications require. Fabrication and sintering methods, once believed to be sufficient, alone, have been found to be inadequate in the manufacture of such advanced components. Realization of the importance of the starting powders has led to efforts to produce materials of ultrahigh purity and ultrafine particle size with very narrow particle size distributions. Such powder characteristics are essential for the fabrication of components with high density and with the desired mechanical, electrical, or magnetic properties called for by the specific application. Novel ultrafine and ultrapure powder preparation techniques are discussed and effects of impurities on the powder characteristics, particle size and morphology, sintering behavior and properties of the finished product are elucidated.

Jan 1, 1992

By Jeffrey J. Daniels

Advances in borehole geophysical research for mineral assaying, and remote detection of mineralization away from the borehole. Nuclear activation measurement research has provided accurate in situ assays of economic metals with neutron-gamma activation, using a high resolution intrinsic-germanium detector. Although nuclear activation analysis is the present "best-hope" for obtaining in situ assays for some elements, gamma-gamma and magnetic susceptibility measurements can provide accurate assays for lead-zinc and magnetite, respectively. Borehole optical spectroscopy and x-ray fluorescence are being investigated as possible in situ assaying techniques for some minerals. More laboratory and field calibration research is needed before nonlinear complex resistivity (NLCR) can be routinely used as a quantitative assaying tool. Field tests have shown that variations in the local geologic environment can affect the quantitative accuracy of assay values from downhole NLCR measurements. Deeply penetrating borehole geophysical methods are increasingly being used for mineral exploration as drilling costs and exploration have increased. Borehole electrical measurements have been shown to be useful for detecting conductive orebodies that are not interesected by a drillhole. Hole-to-surface resistivity, and surface-to-hole time-domain electromagnetics are demonstrated to be particularly effective for defining mineralized zones in a massive sulfide environment. Borehole gravity meters and three-component magnetometers have been developed and should prove useful for defining geologic anomalies away from the drillhole.

Jan 1, 1985

By J. F. Brune, A. Verma

"Face ignitions in underground coal mines are a major risk for underground mining operations, as they can lead to methane or coal dust explosions. The 2010 disaster at the Upper Big Branch Mine resulted in 29 fatalities due to a methane and coal dust explosion initiated from a face ignition. Much research has been conducted to mitigate face ignition hazards, from water sprays to installing passive and active explosion barriers. Despite the increased use of water sprays in U.S. coal mines, there have been more than 50 documented face ignitions in the U.S. underground coal mines since 2010, indicating that this hazard still prevails. This paper will examine the statistics of face ignitions and gas explosion in U.S. coal mines based on MSHA data. It will study factors contributing to these face ignitions and outline best practices for their prevention based on experience and practices worldwide. INTRODUCTION Methane and coal dust explosions are one of the major causes of coal mine disasters in the U.S. and around the world. Such disasters have resulted in the large number of fatalities and loss of mine infrastructure. The recent explosion at the Soma coal mine in Turkey has caused the death of 301 miners (Mining Turkey, 2014). As documented by U.S. Mine Safety and Health Administration (MSHA, 2015a), the U.S. coal mining industry has also experienced several catastrophic mine explosions with accidents at Upper Big Branch mine, Darby mine, Sago mine and Jim Walter Resources No. 5 mine in the last decade, causing the deaths of almost 60 miners. Every explosion requires a source of ignition, the right amount of fuel and oxygen. In underground coal mines, methane acts as a fuel while ventilation air acts as a source of oxygen. The source of ignition may vary from spontaneous combustion, electrical equipment and switchgear, mechanical heat sources, face ignitions due to friction rock-on-rock or from cutter bits and lightning strikes. Under the right conditions, energy of less than 0.3 mJ is sufficient to ignite methane-air mixtures (James, 2007) that can result in a catastrophic explosion. Much research has been done to mitigate the methane explosion hazard by proper dilution, continuous monitoring of methane and elimination of ignition sources. Historical studies indicate that face ignitions are the major cause of explosion in underground coal mining operations worldwide (Belle, Carey, and Robertson, 2012). Statistics shows that most mine disasters were started from a small face ignition, which turned into a major explosion fueled by additional methane and coal dust (Belle et al., 2012). To investigate face ignition hazards, researchers must study potential ignition sources as well as potential explosive atmospheres near mechanical coal cutting operations. Statistical analysis of U.S. coal mine face ignitions reported by the U.S. Mine Safety and Health Administration (MSHA, 2015b) shows that several factors are responsible for face ignitions."

Jan 1, 2016

By M. D. Flavel

My paper relates to bond's third theory of comminution and suggests work be used as a basis for designing crushing and screening plants, this will give more accuracy than existing methods, As stated in the abstract, this paper is only a synopsis of my official paper, many of the questions that might arise in this brief address will be answered by referring to the detail i n the main paper $ Because of the limited time available and the fact that many people here do not need to study the aspects of crushing and screening in depth, i will highlight-those sections of the paper which show how major capital, operating and energy cost savings can be achieved in the process, I will develop the theme in the following manner, Firstly, pointing out, why a new approach is needed to the fundamentals of crushing and screening, Secondly, by setting forth some theory to describe what we are trying to accomplish, Thirdly, by looking at important factors which need to be observed in designing plants and applying machines to comply with this theory, Lastly, i will put forth some ideas on how we might develop this theory to make the industry more efficient, At the outset, i have to say my approach to this process is entirely new, for those used to applying machines and designing plants on existing criteria, they will find this theory easier

Jan 1, 1977

By K. Darcovich

The wettabilities of agglomerates made from coals of several different ranks were measured by the adhesion technique. Oil levels from 0 to 10% by weight were used. As was expected, it was found that higher-rank coals are more easily oil-wetted and that the surface properties of the agglomerates correlate with agglomeration recovery and ash removal data.

Jan 1, 1992