Search Documents

By Joseph Fernandez, Luminita Calin

INTRODUCTION The Tunnel and Reservoir Plan (TARP), commonly known as the Deep Tunnel Project, is the daring and unique concept developed by the Metropolitan Water Reclamation District of Greater Chicago (MWRDGC) as a two-phase solution to the problem of waterway pollution and basement flooding due to sewer system backups created by the combined sewer over-flows (CSOs). Phase I, primarily for pollution control, includes the tunnels, shafts, connecting sewers and structures. These Phase I facilities intercept, during wet weather events, the CSOs within the MWRDGC TARP service area. The tunnels and shafts provide temporary storage of the CSOs for subsequent treatment at Water Reclamation Plants (WRP) before discharging into waterways. Ultimately, upon completion of Phase II, the tunnels, located from 45 m(150 ft) to 100 m (330 ft) below ground, will convey the CSOs to reservoirs for storage until WRP capacity is available. Phase II, which includes the reservoirs, pumping facilities, additional tunnels and shafts, has been planned to serve a dual purpose. The reservoirs provide storage of excess flows during wet weather events, those beyond the WRP capacity. Following the wet weather events, the stored flows can be conveyed, at controlled rates, to the WRPs for full treatment. These excess flows previously would have resulted in both overflows into the waterways and eventually backups in the local sewer systems. The storage capacity of the reservoirs also will promote the full utilization of the conveyance capacity of the tunnels and shafts, which in turn results in optimizing the conveyance capacity of the existing sewer systems. Therefore pollution control is further enhanced by allowing for capture of a greater volume of CSOs and greatly minimizing backups in the local sewer systems. The TARP project consists of four systems: O’Hare, Mainstream, Des Plaines, and Calumet, covering a total area of 971 km2 (375 mi2) and serving the City of Chicago and 51neighboring communities as shown in Figure1. With only two contracts left before completion of the Phase I tunnels, the 12.7km (7.9mi) Torrence Avenue leg, to be awarded in 1997, and the 12.4km (7.7mi) Little Calumet leg unfunded as of yet, both part of the Calumet System, the pollution control phase of the project is now 86% complete (Table 1).

Jan 1, 1997

By W. D. Hausel

The Wyoming Province is an Archean craton which underlies portions of Idaho, Montana, Nevada, Utah, and much of Wyoming. The cratonic block consists of Archean age granite-gneiss with interspersed greenstone belts and related supracrustal terranes exposed in the cores of several Laramide uplifts. Resources found in the Province and in the adjacent accreted Proterozoic terrane include banded iron formation, Au, Pt, Pd, W, Sn, Cr, Ni, Zn, Cu, and diamonds. The Province shows many similarities to the mineral-rich cratons of the Canadian shield, the Rhodesian and Transvaal cratons of southern Africa, and the Pilbara and Yilgarn blocks of Western Australia, where much of the world's precious and strategic metal and gemstone resources are located.

Jan 1, 1991

By Julian W. Feiss

Before undertaking to present to you a current analysis of copper, I would like to preface my remarks with a few observations that in themselves have a bearing upon commodity reviews in general. Having sat through a large number of such reviews since first joining the A. I. M. E. nearly forty years ago, I have no illusions about the hazards of the undertaking. If a speaker presents a statistical summary of commodity economics for the last year, most of his audience, having already read at least four commodity summaries on the identical subject, either get up and walk out or fall asleep. Should the latter happen, and were the listener to tumble from his chair and break his neck, obviously the speaker is liable. The subject matter seldom lends itself to histrionics on the part of the speaker so dangers of heart attack in the audience are not too great. Therefore the speaker, in order to retain listener interest, resorts to prophecy. Such venture was undertaken long ago by weather soothsayers, the "harouspex" of Ancient Rome, who generally cut up a sacrificial sheep and after staring at the entrails made their predictions which I understand had a batting average somewhat better than those undertaken on Wall Street based upon Dow Jones averages. Not being a licensed harouspex I cannot undertake predictions. I shall, however, fall back upon the experts.

Jan 1, 1965

By K. D. Luxbacher, J. T. Davis

"A wind tunnel was designed to examine air flow, heat transfer and layering near an active fire at a working face. This tunnel simulates an active entry in an underground coal mine including an attached cross-cut of similar dimensions. A steel rectangular duct 1 ft. (0.305 m) tall, 3 ft. (0.914 m) wide and 10 ft. (3.05 m) long composes the main body of the tunnel and represents a mine entry. Air flow is generated by an exhausting centrifugal fan attached to one end of the crosscut. This fan was sized to supply air velocities based on Froude scaling. A 6 in. (15.25 cm) propane burner is used to simulate fires of various heat release rates at the working face. Thermocouples are used to map heat layering in the tunnel. Ports are installed for the introduction of tracer gases into and from sampling the system. Barometric, differential pressure, and temperature sensors are also included to monitor environmental conditions. Details about the design and testing of the system are presented including an overview of how the tunnel was scaled to accurately represent fire and flow phenomena. Finally, the proposed use of the tunnel for better understanding of mine fire phenomena and prevention is given. INTRODUCTION Fires in underground mines have been a concern since the dawn of mining. While technological advancements, regulations and best practices have improved both fire detection and firefighting techniques, mine fires continue to represent high risk events. From 2006 through 2015, fires accounted for 1.06% of fatalities in underground coal mines and 0.85 percent of fatalities in all underground mines in the United States (U.S. Department of Labor, 2006 to 2015). In addition to the risk of loss of life, mine fires can cause millions of dollars in equipment damages and lost production revenue. Extensive research has been conducted on how fires occur and spread in underground mines. In addition to testing conducted by government agencies such as the Mine Safety and Health Administration (MSHA) and the National Institute for Safety and Health (NIOSH) (e.g.(Liming, 2006), researchers like Verakis and Dalzell (Verakis, 1988) and Lowndes, et. al. (Lowndes, 2004) have furthered this field by studying ignitions and propagation of conveyor belt fires. While the studies of belt fires in mines are extensive, studies focused on fires at the working face are few in number. The particularly confined space and limited access to a working face, coupled with less robust, temporary ventilation controls create a unique environment that warrants special attention. Separate from studies on mine fires, the use of tracer gases to characterize flow patterns in normal mining ventilation is well established. In 1982, Timko and Thimons (Timko, 1982) outlined current and future applications of sulfur hexafluoride (SF6). However, little experimentation has been conducted to study specifically how tracer gases might be used to evaluate active mine fires and the fires’ effect on the surrounding mine environment (e.g.(Lindsay, 2014). In order to better understand the dynamics of smoke layering from a fire in an enclosed space, a small-scale apparatus was designed to map smoke layering and to examine other aspects of fire behavior at a working face. In addition to studying smoke flow around an active fire, experiments will be conducted using tracer gases in order to determine how they might be used to evaluate an underground fire."

Jan 1, 2017

By Siddhartha Roy, Hemant Agrawal, Ram Madhab Bhattacharjee, Devi Prasad Mishra

Heat stress is a major concern for the health, safety and productivity of miners working in hot and humid underground mines. At greater depth, heat inside underground mines increases due to geothermal gradient, heat released from high-capacity machinery, exposed rock surface, auto-compression of air, human metabolism, etc. Prolonged physical work in thermal environments severely affects the health, safety and efficiency of miners. In order to address this important issue, a systematic literature review (SLR) has been conducted. This SLR aimed to identify the research gap in the area of heat stress effect on underground miners and its control. An extensive literature search was carried out on numerous digital databases, grey literature and conference proceedings to identify relevant research work for this review. Moreover, the impactful studies, methodologies and preventive measures undertaken during the past five decades on the effect of heat stress on underground miners were retrospectively analysed, with a broader aim to explore the need for further research on this pertinent topic. Overall, 571 references were identified from the literature review, out of which 51 research articles addressing the sources of heat, heat stress effects on miners, heat stress indices and control measures for heat stress in underground mines were selected as primary papers for detailed review. Pre-developed fatigue is one of the prime causes of health hazard, safety and productivity loss of miners working in underground high heat stress zones. Hence, development of a better heat stress index integrating personal, environmental parameters and pre-developed fatigue (PDF) of miners is essential.

Jan 14, 2022

By T. Grammatikopoulos, C. Gibson, M. Aghamirian

"Lithium is a silver-white alkali metal that has recently become a target commodity for many junior mining companies. Lithium has a wide range of applications including ceramics and glass, lubricating greases, air treatment, continuous cast mold flux powders, polymer production, and primary aluminium production, but the current popularity of lithium can be attributed to an anticipated increase in demand for lithium ion batteries. The most common lithium-bearing minerals occur globally in pegmatites and granites. Spodumene [LiAl(Si2O6)] is the most desirable economic lithium-bearing mineral due to its high lithium content (theoretical Li2O content of about 8 wt%). However, lithium can also be hosted in petalite, micas, tourmaline, and phosphate minerals. In Canada there are a number of spodumene deposits in Ontario and Quebec at development stage that have the potential to help narrow the forecast lithium supply gap stemming from the widespread acceptance and use of electric vehicles. This paper discusses the beneficiation of hard rock lithium deposits, including an in depth review of the use of flotation to upgrade spodumene. A review of the use of dense media separation (DMS), magnetic separation, and roasting as means to process spodumene bearing ores is also discussed. INTRODUCTION Lithium is a soft, silver-white alkali metal with atomic number 3. As of 2015, the end use of lithium was estimated to be as follows: lithium-ion batteries (35%), ceramics and glass (32%), lubricating greases (9%), air treatment (5%), continuous casting mould flux powders (5%), polymer production (4%), primary aluminium production (1%) and other uses (9%) (Jaskula, 2014). Lithium is found in brine lake deposits containing lithium chloride and in hard rock pegmatite deposits. It can be sold in a range of product types; as mineral concentrate, brine, compound (lithium carbonate or lithium hydroxide) and metal depending on its intended end use (Goonan, 2012; Jaskula 2014). In the 1990s the United States and Chile were the largest producers of lithium globally, primarily from brine operations (Ober, 1994). Most of the lithium compounds produced over this period were consumed in the glass, ceramics and aluminium industries. In the 1980s and 1990s there were two major lithium operations in the United States: brine operations at Silver Peak, Nevada, and a spodumene mine and lithium carbonate/lithium hydroxide plant in Kings Mountain, North Carolina. The Kings Mountain operations ceased production in 1991 and were eventually dismantled in 1994. Brine operations were also active in Argentina and Chile, while the largest lithium ore deposit in the world was operated at Greenbushes, Western Australia. During this period it was predicted that major shifts in demand for lithium would come from the success and widespread use of electric vehicles (Ober, 1994)."

Jan 1, 2017

By R. A. Metz, Willard C. Lacy

Rather than attempting to present a summary of the many and highly varied papers that have been presented at this symposium on sampling and grade control, I will attempt to extract the general philosophy of analysis and approach, and attempt to identify the trend of future developments. First, the term "sampling" is used with its broadest connotations. A sample consists of a representative portion of a larger mass, and must represent the mass not only in the grade of contained metals or minerals, but also in all other respects in terms of mineralogy and mineral quality (1, 5), deleterious materials, recoverability of economic components, physical behavior, geophysical response (1), and even archaeological and environmental aspects (7, 11). The sample must be taken from a locality and in such a manner and quantity that it is representative of the larger rock mass. This calls for complete and accurate geological control and an understanding of the nature and distribution of the contained chemical and physical elements and a record of the effectiveness of the different sampling methods. Second, value of a given mass of ore material is based upon its profitability - the difference between recoverable value and costs to achieve recovery, beneficiation and sale. There is a strong movement in mining geology control toward more complete analysis in determining cutoff grades and in grade control, as illustrated by the kriging of metallurgical recovery factors as well as grade at the Mercur Mine (8). To achieve a "profitability factor" as a guide for economic mining practice requires further integration of: 1) the value of contained metal or mineral, 2) percentage recovery of values, 3) dilution of ore with waste rock, 4) addition to, or loss of value as a consequence of by-product materials or deleterious components, 5) cost of producing a saleable product plus minimum profit to justify the effort (cutoff), and 6) cost of land restoration (7, 11). All these parameters vary with the rock type, rock structure, mineralogy, depth, geometry, mining and metallurgical methods, but they must be sampled and analyzed if sampling and grade control are to reflect profitability. A wide variety of deposits has been presented at this symposium; each deposit with its own problems and special solutions. Deposits containing high unit-value components, e.g. precious metals and diamonds, present special problems in the obtaining of accurate samples and generally require statistical analysis control methods or may disregard or modify occasional high or occasional low values, based upon experience (12). Grade control may be accurate for the long term but may vary for the short term. Bulk sampling is always essential. Deposits containing metals or minerals with low unit value are very sensitive to transport costs, and they are often very sensitive to small amounts of deleterious components or differences in physical or chemical behavior. Problems of sampling and grade control change with the genetic type of deposit, with the stage of deposit development and with the size of the information base. Precious metal epithermal deposits (2, 6, 8), because of rapid vertical zonation and erratic lateral distribution of values, have always been difficult to evaluate and maintain grade control and ore reserves. On the other hand, evaluation and grade control are relatively easy in bulk-lowgrade deposits (4, 13). However, these deposits generally have a low margin of profit and are sensitive to mining and beneficiaton costs, price fluctuations and political costs. Industrial mineral deposits (5) often must be evaluated on the basis of their behavior, rather than by chemical analysis. Environmental impact generally increases with the scale of the operation, but certain elements or minerals have especially high impact effects (7, 11). In the exploration phase there is no production control of sampling procedures and careful geological observations are particularly essential. The greatest number of problems is related to the oxidized outcrop where the chemical environment of the ore body has changed and the contained values may have been enriched, depleted or values left unchanged (2, 6). Present evidence suggests that gold values may be very mobile under certain conditions (2, 6) and stable under others. Everything must be sampled in detail. Principal values and by-product or deleterious elements may vary dependent upon their position within the soil profile. Such factors as geomorphic position, erosion rate, vegetation, climate, etc., may affect the interpretation (1, 3). During the development phase it is equally easy to overtest, to have "paralysis by analysis," as to undertest (3, 6). Bulk samplng and testing are

Jan 1, 1992

The U.S. National Institute for Occupational Safety and Health (NIOSH) conducted a study to determine the effectiveness of a filtered air delivery system to reduce respirable dust exposure of roof bolter operators in underground coal mines. When performing roof bolting operations, roof bolter operators may experience exposure to high levels of respirable dust during a working shift, especially when working downwind of the continuous mining machine. While drilling and installing roof bolts, this filtered air system supplies a clean curtain of air over the roof bolter operator by means of a plenum mounted beneath the canopy. This experimentally designed air curtain, adapted for roof bolting machines used in this study, is based upon previous design prototypes, computational fluid dynamics (CFD) simulations and trial-and-error testing. Both the prototype and final designs were tested in the full-scale mining galleries at the Office of Mine Safety and Health Research (OMSHR) in Pittsburgh, PA before being taken underground for field testing. Test results of the system in both laboratory and field studies show reductions in operator exposure to respirable dust when the operator is positioned directly under the protected zone of the canopy.

Jan 1, 2012

By A. López-Valdivieso, M. A. Corona-Arroyo, M. Llamas-Bueno

Magnetite (Fe3O4) ore is concentrated by low-magnetic-field drums to recover a magnetite concentrate that is low in silica (SiO2). The presence of SiO2 in the magnetite concentrate for steel production increases the steel processing costs, so a major challenge in magnetic concentration is to lower the SiO2 grade in the Fe concentrate. This work presents studies that were carried out on the removal of SiO2 from the magnetite concentration at the plant scale. Studies were performed with a three 36 × 96″ drum unit processing 46 ton/h of rougher magnetite concentrate. These studies showed that silica appears in the magnetite concentrate by three mechanisms, namely SiO2 entrainment in Fe3O4 chains, heterocoagulation between Fe3O4 and SiO2 particles, and mineral locking of SiO2 to Fe3O4. The SiO2 entrainment mechanism had the highest contribution (75%) to the SiO2 recovered in the Fe concentrate. Electrokinetic studies on Fe3O4 and SiO2 showed that heterocoagulation occurs because of the low negative zeta potential of the minerals at the pH of the plant slurry. This study also showed that a high percentage of ultrafine size SiO2 particles trapped in Fe3O4 agglomerates was not removed by the dilution water for the slurry fed to the drum. To lower the SiO2 recovery in the drum magnetic concentration process, work should be directed towards the removal of trapped SiO2 in Fe3O4 agglomerates.

By S. M. Hsiung

Chain pillar design formula under weak roof condition was developed by statistically analyzing the results from the three dimensional finite element parametric analyses. The parameters such as mechanical properties of the roof and floor strata, overburden depth, panel width and length, and coal strength were incorporated in the formula. A conversion formula which transfers a rectangular chain pillar into a square chain pillar of equal strength is proposed. The influence of high in-situ horizontal stresses, which are often encountered in the coalfield, on chain pillar stability is also discussed.

Jan 1, 1984

By John R. Gaines

I am not a member of AIME, and this is my first annual meeting. As a lifelong member of the non-ferrous metals industry I have enjoyed listening today to speakers point with pride and view with alarm the public relations activity or lack thereof in the halls of government, as well as at the grass roots. There is much to be alarmed about, to be sure, but also some accomplish¬ments to be viewed with pride. Other speakers have given a broad overview of our industry's relations with their several publics. I will be specific about two incidents in which The Anaconda Company faced the loss of confidence of a large portion of its publics: the nationalization of our properties in Chile in 1971 and the closing of our under¬ground mines in Butte, which was announced last October. If I have a minute left over, I will speak about our concern for the loss of confidence in business institutions which has been re¬vealed in recent public opinion polls.

Jan 1, 1975

By John J. Rhodes

I welcome this opportunity to give a Congressman's birdseye view of a subject which I believe holds great potential for the future in helping meet the needs of people, with minimal adverse impact on the environment. All mankind, not just the people in this great nation, faces the need for additional usable space. In some parts of the United States the problem arises from rapid urbanization of the surface and little utilization of the subsurface. Everywhere there is an increasing problem of insufficient space arising out of the increasing population crush and growing demands for open space, housing, water, transportation, communication, and social service. You are the technicians to whom we look for assistance in finding answers. We look to you also to provide guidance for broad policy decisions concerning underground space. I prepared for a career practicing law, but since 1952 I have been a member of the House of Representatives. In this latter capacity I deal with programs designed to help solve all kinds of problems. But, naturally, I am especially interested in the water scarcity and other environmental problems of my home state of Arizona and the arid and semi-arid areas in the West. This North American Rapid Excavation and Tunneling Conference has as its theme: "Tomorrow's Tunneling Technology Today." I have a very great interest in this potential of our underground space resource. The Central Arizona Project now getting underway in my state will consist in part of tunnels and underground pipelines to convey life-sustaining water from the Colorado River to people and lands across Arizona to the Phoenix and Tucson areas.

Jan 1, 1997

By G. T. Lineberry

Horsepower requirement is recognized as a most important equipment characteristic. Other critical equipment characteristics will be isolated and analyzed by traditional operations research techniques, using off-highway trucks as an archetype. A computer search technique has been developed, employing various production and cost analyses. With this model, the optimum combination of horsepower, capacity, and velocity can be found, minimizing handling cost per ton. An example of the program's use and interpretation of its results will conclude the paper.

Jan 1, 1984

By R. Fred Pena

The Tower Mill has proven to be a grinding machine with a demonstrated application flexibility. Variations in applications have proven to be numerous. This mill was originally intended for fine grinding applications. Subsequent testwork and installations have demonstrated the mill can be utilized in place of ball mills as secondary mills. The following lists a few of the circuits tested: 1. Tower Mill secondary receiving feed from a primary SAG mill grinding stage. 2. Tower Mill as tertiary grind unit following a rod mill/ball mill. 3. Tower Mill as secondary grind unit following a primary ball mill. 4. Tower Mill as a limeslaker. 5. Tower Mill grinding as a primary unit taking limestone crusher discharge. Applications demonstrate the mill is energy efficient and is sensitive to the following consideration: 1. Circuit chosen. 2. Top size of feed. 3. Product size required. 4. Classification equipment performance. 5. Media size required. 6. Media type required.

Jan 1, 1986

By Dirk van Zyl

Three conditions are required for a risk to be realized: (1) a source of risk (i.e., hazard) must exists (2) some process must take place which will lead to the exposure of people, animals, and/or the environment to the hazard: and (3) as a result of the expense, undesirable effects are produced on the people, animals, and/or the environment. A comprehensive risk assessment addresses all three of the conditions through the following four steps: (1) risk source (hazard) characterization, (2) exposure assessment, (3) dose-response assessment, and (4) risk estimation. Although the terminology may differ, the overall approach of financial, public health, and environmental risk assessments is the same (National Science Foundation, 1985).

Jan 1, 1988

The US economy grew at a rate of 4% in 1994 and the gross domestic product rose to $6.74 trillion. With 261 million people - 605,000 in mining, including petroleum -the United States has l 10 million dwelling units and 200 million licensed motor vehicles. New private housing units authorized in 1994 rose 14% to 1.4 million units. New car production rose 11 % to 6.6 million units, while truck and bus production rose 30% to 5.2 million units. The inflation rate was less than 3% and the prime rate of interest averaged 7.15%. The producer price index (1982 = 100) for fuels and related products and power was down 4% to 78, while metals and metal products rose 5% to 125. Chemicals and allied products rose 3% to 132, and non-metallic mineral products rose 3% to 124. The merchandise trade deficit rose 25% to $166 billion. Disorder in the former Soviet Union led to substantial dumping of mineral materials. With vast mineral resources, the former Soviet Union land area totaled 22.4 million km2 (8.6 million sq miles). In comparison, the North Ameri¬can Free Trade Agreement (NAFTA) area (United States, Canada and Mexico) totals 21.4 million km2 (8.3 million sq miles).

Jan 1, 1995

By K. Saberyan

A technique is described for the solvent extraction of zirconium. In this method, zirconium has been extracted quantitatively from 0.005 M sodium salicylate solution at pH 2.5 - 3 using 0.01 M triphenylphosphine oxide dissolved in toluene as an extractant. Zirconium has also been recovered quantitatively from 0.2 M potassium thiocyanate solution, but extractions in nitric and hydrochloric acids (as media) were negligible. The resulting extracted metal ion has been stripped with sulfuric acid (0.5 M) and determined with inductively coupled plasma atomic emission spectrometry. This method has been applied successfully to achieve 95% recovery of zirconium from zircon concentrate.

Jan 1, 2010

By C. E. Schmidt

Homestake crushing and grinding, practice-was completely revised during the period of 1951-1953. During the conversion, both crushing plants at the head frames the Ross and the Yates, were changes at each plant involved replacing the two 8K gyratories with a rebuilt, The flow sheet single thirty inch gyratory for primary crushing to four inch. The gyratory discharges to a seven foot Symons standard cone crusher set at 1-1/8 inch opening. The cone discharge goes to Tyrock screens fed by vibrating feeders. Screen openings, are l/2 inch by 5 inches: at the Ross. Plant, and 3/8 inch by 5; inches at the Yates. Screen oversize goes to a seven foot Symons cone brusher converted to the short head type; the crusher setting is 5/16 inch. Crusher, discharge; is closed circuited with the Tyrock screens, The above crushing installation delivers a minus 5/8 inch rod mill feed to the mill bins. The crushing revision eliminated the-180 heavy South African type stamps, which had previously reduced the 2 inch crushing plant product to a minus 5/8 inch feed for the 10 rod mills, and 8 ball and pebble.; mills, other revisions in the mill flow sheet, resulted in 3 identical units of about 1350 tons per day, capacity per unit, Each unit consists of an open, circuit 6 foot by 12 foot rod mill, fed from two 24 in by 48 inch vibrating feeders of the four feeders available per unit. A gathering belt delivers the ore discharge of the feeders to the Transportoweigher, which in turn discharge s, into the rod; mill feed spout. Rod Mill discharge is the feed for the 9 foot by 11 foot ball mill, The ball mill is closed circuited with a 16 foot by 30 foot Dorr Classifier. The Homestake make amalgamator, for coarse gold recovery in the ball mill circuit, made' necessary a 36 inch spiral conveyor between the classifier rake discharge and, the combination drum and double scoop feeder on the ball mill See Figure l - the flow sheet of the two stage grinding units.

Jan 1, 1958

By Paul Gribbon, Greg Colzani, Jim McDonald

The $300 million West Side Combined Sewer Over?ow Project consists of over5.5 kilometers of soft ground tunnel, an 833-million liter per day (220-MGD) deep shaft pump station, 3 kilometers of micro tunneling, and other miscellaneous shafts and pipelines. The construction contract, underway since September 2002, is a reimbursable cost plus fixed fee contract that included a quali?cations-based contractor procurement process and has undergone some modi?cation since execution. This paper will describe the contractual issues addressed to date, dispute resolution, where improvements can be made, and how an Owner can evaluate whether this type of contract is the best approach for an underground project.

Jan 1, 2005

By John L. Stafford

The ROEMMC combustion system was originally conceived as a means of utilizing solid fuels that would otherwise have been wastes requiring disposal and convert these fuels into useful energy sources. This concept follows as an extension of the application of residual waste incineration with energy recovery practiced in the lumber, manufactured board, sugar cane, and other industries. The incineration of these wastes in the furnaces of steam generating equipment is thoroughly described (1, 2, 3, 4, 5, 6, 7). The fundamental principle of the ROEMMC system is temperature control which makes possible the maintenance of the non-combustible fraction of these solid fuels in a dry solid state and their separation from the gaseous products of combustion. This philosophy of ash removal and the "slagging" philosophy are compared. The ROEMMC equipment function and applications are described.

Jan 1, 1978