Search Documents

By W. F. Riggs

1 Flotation Analogy To explain flotation in simpler terms the following analogy will be used. A factory (the flotation cell) manufactures a product (collector coated mineral). The product (collector coated mineral) is transported to market (the launder). A truck (the frother) is used to transport the product (collector coated mineral) to the market (the launder). The truck (the frother) transports the product over a road (the froth bed). The truck (the frother) and product (collector coated mineral) are supported by tires (the air). 2 Assumptions This operating philosophy assumes that the correct collector dosage is present along with the correct particle size distribution, pH conditions, etc. and that the minimum required frother dosage is correct. 3 Collector Addition The collector addition as used at a flotation plant is based on dosage rate as determined by the amount of mineral value entering the concentrator. Collector is normally added at two points in the concentrator: The primary flotation circuit and staged addition in the rougher scavenger circuit. Surveys have shown that the staged collector addition provides an increase in the kinetics and increases the recovery of the valued mineral in the rougher scavenger circuit. 4 Frother 4.1 Frother Dosage As explained in the above analogy, frother can be likened to the truck that transports the product (collector coated mineral) to market (the launder). Just as you would not use a truck rated at 15 tonnes to transport a 20 tonne load, you cannot expect to transport coarse minerals to the launder when there is insufficient frother present. Frother dosage must always be at, or above the minimum target. If less frother than the required minimum is used, then coarse mineral particles will not be supported and transported to launder where the mineral is recovered. To the naked eye the froth characteristics, even when insufficient frother is used, will appear to be correct. You cannot see the coarse particles that are not being recovered in the froth. (See Section 4.2 below for an explanation of why this occurs.)

Jan 1, 2006

By M. S. Riyazulla

A model of a new laboratory magnetic separator has been conceived to cater the needs of process engineers and mineralogists world over engaged in mineral characterization and beneficiation. It would be essentially a laboratory instrument for the separation and concentration of various ferro and non-magnetic minerals. Based on the basic concept of Frantz Isodynamic Magnetic Separator, the new separator conceived would not only speed up the work of a process mineralogist and save the energy, but it would effectively separate and sequentially produce about fourteen fractions at a time. In the present paper, the probable operational procedures and the design have been discussed in detail for the various mining companies to assess its economic feasibility. If it could be fabricated, it would have a worldwide market The concept has been patented in author?s name in India.

Jan 1, 2009

By K. Kovári, G. Anagnostou

Slurry and EPB-shield tunnelling have been successfully applied worldwide in recent years. Under extremely unfavourable geological conditions, however, face instabilities may occur. The present paper aims at a better understanding of the mechanics of face failure. For the case of slurry shield, attention will be paid to the time-dependent effects associated with the infiltration of slurry into the ground ahead of the face. Related topics, such as the stand-up time and the effect of the excavation advance rate, will be discussed. In the case of an EPB-shield, a distinction will be drawn between fluid-pressure and effective pressure in the chamber. The effective pressure can be visualized as a “grain to grain” contact pressure between the muck and the ground at the face. The water pressure in the chamber reduces the hydraulic head gradient in the ground and, consequently, the seepage forces acting in front of the face. The face is thus stabilized both by the direct support of the pressurized muck and by the reduction of the seepage forces in the ground. The paper includes normalized diagrams which allow the assessment of tunnel face stability.

Jan 1, 1997

By M. Tokoglu

Accurate estimation of resources is one of the major challenges in mineral project evaluation. Contemporary mineral resource estimation practice calls for contribution from several disciplines and execution of several interdependent tasks. 3D estimation domain modelling is obviously one of the most essential components of such a substantial process which forms the basis of this research. The study constitutes a comparative analysis of four major domain modelling techniques; (i) explicit modelling, (ii) implicit modelling, (iii) indicator kriging, and (iv) conditional simulation. It involves comparison of outcomes for alternative scenarios to assess the implications of the modelling decision on resource estimates of a polymetallic massive sulfide deposit located in western Turkey. Thus, identical grade estimation method and parameters are considered to identify the discrepancies arising only from the choice of the domain modelling approach and underlying assumptions. Economic implications are demonstrated in the form of range of outcomes for the extends of the ultimate pit, ore tonnages (min:37.0 Mt, max: 46.7Mt), waste tonnages (min:201.2 Mt, max: 251.2 Mt), stripping ratios (min:5.18, max: 5.71), and total pit values (min: $1.05B, max: $1.45B). Examination of solid models as well as cross-sections revealed that major discrepancies are observed beyond outlying drillholes. Therefore, it has been proposed that assumptions regarding extrapolation distance is the main source of mentioned dissimilarities. Key words: Domain modelling, explicit modelling, implicit modelling, indicator kriging, conditional simulation INTRODUCTION Resource estimation is apparently a challenging process calling for extensive expertise and input from several sources, each of which introducing its related uncertainties. In the last decades, substantial role of quantitative analysis of several forms of risk and uncertainty in evaluating projects’ upside potential and downside risks has been realized. Studies indicated that mining companies have been severely impacted because of not meeting project expectations. As noted by Vallee (2000) “… in the first year of operation after start-up, 60% of mines surveyed had an average rate of production less than 70% of designed capacity”. Several other studies on mining projects also revealed that uncertainties related with the resource model are one of the major contributors of mentioned shortfalls. In this perspective, quantification of uncertainties associated with each component of estimation process is critical. 3D estimation domain models capturing major mineralization controls are the fundamental components of contemporary mineral resource estimation. Domain models are key guiding tools for estimation and are products of a complex process involving many unknowns and assumptions. There exists a number of 3D modelling alternatives which are distinct with respect to complexity, time and effort involved. Acknowledging potential influences on downstream mining practices and relavent economic implications, risks and uncertainties associated with 3D domain modelling are critical yet poorly studied aspects.

Jan 1, 2019

By S. Mishra, C. Shon, D. Saylak

Only 40% of fly ash generated by the power plants in US are recycled and used for commercial applications. Of these, the high lime, Class C ash had been preferred. Systematic laboratory and field-scale studies have shown that, by including calcium chloride in the mix design of stabilization of roadbed materials, both Class C and Class F fly ashes can be effectively utilized. Test data reveal that the addition of calcium chloride to the system accelerates its curing rate, thereby increasing early strength and long term durability of the constructed road. For road construction, a preblended Class F fly ash–CaCl2 system tends to be more forgiving than the Class C fly ash–CaCl2 system. The former system produces more durable roads. The role of calcium chloride as an accelerator in these systems is discussed along with a mathematical model developed for fly ash- CaCl2 stabilized roadbed systems.

Jan 1, 2007

By R. K. Simpson, C. S. Eldridge, M. H. Tyler, J. P. Hodgkison

The WMC Olympic Dam Operation in South Australia is an integrated site, involving brown fields exploration through to production of copper cathode, uranium oxide, gold and silver bullion. The Geology and Analytical Services (GAS) Department reflects this totality and, therefore, is perhaps a unique construct in the industry. It comprises Geology, the Metallurgical Laboratory and the Analytical Laboratory, offering a single point of contact in matters of metal discovery and tracking through mine design, production, beneficiation and final product certification. This structure promotes value adding by removing traditional barriers between groups that can deliver more, collectively, than as individual units. This approach to value adding by bringing disparate groups together is echoed in each of the three sections where enhancements in the traditional value adding activities have been delivered by multi-skilling and encouraging overlapping involvement.

Jan 1, 2002

By P. Tong-jiang

We studied mineralogical characteristics of the vermiculite samples from seven mines in China. We found three types of interstratified structures in the investigated samples: 1:1 regular interstratified structure, segregated interstratified structure, and random interstratified structure. The vermiculite samples from six mines are mainly composed of phlogopite?vermiculite interstratified minerals, and the samples from the other mine are composed of chlorite?vermiculite interstratified mineral. The samples with phlogopite?vermiculite structure have high contents of K2O, TiO2 and Na2O. The samples with chlorite?vermiculite structure have the highest contents of MgO and Al2O3. The cation exchange capacity of the samples is 17.3?99.0 mmol/100g.The exchangeable cations of phlogopite?vermiculite samples from Weili Mine mainly include Na+ and Ca2+, while those of phlogopite?vermiculite samples from Tongguan Mine mainly include Mg2+ and Ca2+. The thermal expansion ratio of the samples is between 9 and 32. The exfoliated vermiculite products from Weili Mine have the best mechanical strength.

Feb 27, 2013

By T. J. McKeon

Partition curves are used to evaluate the separation performance of gravity-based concentrators. The partition curve is used to identify the nominal density cutpoint and relative sharpness of the separation. In addition, the graphical representation makes it possible to quickly identify the root cause of misplacement based on the characteristic shape of the partition curve. Partition curves have been traditionally constructed using data obtained from float-sink tests using heavy organic liquids. These toxic liquids are environmentally unfriendly and have been banned in several countries. Another method of establishing the partition curve is to introduce density tracers into the feed and plot the distribution to the lights and heavies. For heavy mineral separations, this approach is generally impractical due to the fine particle size. In addition, the partition data obtained using these existing techniques do not account for secondary factors such as particle shape that may influence the separation. In light of these problems, a methodology was developed for constructing partition curves using experimental data obtained from microscopic grain-counts. This technique, which essentially uses the different mineral species as density tracers, provides a powerful tool for evaluating heavy mineral separations. A case study is provided to demonstrate how this analytical approach can be used to assess and improve the separaton performance in an industrial upgrade plant.

Jan 1, 2005

By Nicholas S. Lynn

Introduction Borne out of the need for reductions in capital expenditure and increased production, several new and innovative carbon systems have been developed for small precious metal heap leach operations throughout the United States. Perhaps the most important aspect of these systems is the carbon column. Though diverse in design, these columns can be categorized into three basic types. The first is known as the gravity flow type or Cortez type. As the name indicates, solution flows via gravity, throughout 4 to 6 columns which are arranged in a normally stepped con- figuration which is conventionally upflow in design. The second type, known as the vertical column, is an arrangement whereby flow is established through pressurization in an upward manner, throughout 4 to 6 columns in a vertically stacked configuration. This arrangement is typically intended for use with small portable heap leach operations and employs a semi-continuous mode thus preventing gravity from occurring. The third type and newest development in carbon columns is an arrangement whereby the solution flows throughout 4 to 6 columns placed in a side by side configuration and pressurized by a single feed pump (Figure 1). A unique aspect to the third type, is that the adsorb and desorb cycles are accomplished in the same column, due to a fixed carbon charge. An in-depth analysis is warranted due to numerous advantages of this arrangement, and is therefore the subject of this paper. Advantages and Variations One advantage to the third type of carbon column is the fact that initial capital expenditures and operating man- power requirements are reduced. Another advantage is that the system can be made fully portable up to a 0.0315 m3/s (500 gpm) capacity. Systems of this nature are operational at several sites. Above this flow rate, the system's portability is one which can be maintained, but disadvantages (i.e. larger diameter carbon column and greater weights) far outweigh the advantages. There are several variations in each of these systems which allow for unique operation. For example, carbon columns made highly portable, can be moved from unitized heap leach operations to central stripping facilities. Although this method has been used in Colorado, transportation of these units has been known to be quite cumbersome. If distances exceed 5 km (3.2 miles) then special front-end loaders are required. This limits heap locations to within 5 km (3.2 miles) of the central processing facility. Another example transports the carbon charge from the heap leach locations to a centralized processing facility; this method is quite effective. For the past 5 years one mine has employed this technique of transporting carbon in 907 kg (1 ton lots), in DOT containers, towed by company pick-ups. This operation uses a vertical column with a 907 kg (1 ton) carbon charge. A third example uses static carbon columns with fixed carbon charges. Carbon Adsorption System The carbon adsorption system (Figure 1) is fed by a single preg solution feed pump. This feed pump pushes the preg solution through all four to six fixed charged carbon columns, which are on line. The sequencing of the carbon columns is achieved using valves. Expansion of the carbon charge is dependent upon the carbon selected. The carbon typically used is a 6 x 12 mesh size, with a nominal flow rate of 0.00135 - 0.00138 m 3/s (22-25 gpm) per square foot of carbon, based on a 40% bed expansion. With 8 x 16 mesh size,

Jan 1, 1987

By Y. Nien Wang

The Devil?s Slide portion of Highway 1 between Pacifica and Montara is often closed due to the instability of the adjacent slopes. Following many years of public input and careful evaluation of alternatives, Devil?s Slide will be by-passed via two inland tunnels, providing a safe, dependable highway between Pacifica and Montara. For the twin tunnels, each 9m diameter tube will accommodate only one traffic lane. Each tunnel tube will accommodate a 3.6 meter roadway, 0.6 meter and 2.4 meter inside and outside shoulders respectively, and 1.2 meter walkways on each side. Cross passages will connect the bores at about 120 meter intervals and jet fans will provide tunnel ventilation. The twin tunnels are approximately 1,250 meter long and 9 meter wide. Excavation will progress from south to north using tunneling techniques that rely on inherent rock strength for support known as the New Austrian Tunneling Method (NATM). Both tunnels will be excavated at the same time, one tunnel face approximately 40 meters ahead of the other. Staggering the tunnels reduces the likelihood of damage from blasting in alternate tunnels. The work schedule is 24 hours a day, 7 days a week resulting in a 24-month timetable to break through to the north portal.

Jan 1, 2008

By J. M. Wempen

Booster fans in underground coal mines are often located using the concept of a neutral point. Normally, intake airways are maintained at higher absolute pressure than return airways, so air leaks from intake to return. By adding a significant pressure force to a region of a ventilation system, booster fans installed in a return airway can increase the pressure in the return so that air leaks from return to intake. This is commonly referred to as recirculation. The neutral point occurs at the location in the system where the pressure difference between the intake and the return airway(s) is zero and at this point there is no leakage or recirculation. Ideally, placing a booster fan near the neutral point minimizes leakage and recirculation; however, in practice the position of the neutral point is not static and it changes as the ventilation system parameters change. This paper presents a study of how changes in the system parameters affect the location of the neutral point in a model coal mine ventilation system. First the effects of booster fan pressure and location on the neutral point are evaluated. Next the effect of increasing mine distance, and therefore mine resistance, on the location of the neutral point and the magnitude of recirculation is evaluated.

Jan 1, 2012

By S. A. Abdel Sabour

Conventional methods for selecting a production plan for an open pit mine is based on the assumption that ore grades throughout mine life as well as market variables are known with certainty. Another important issue that is also being ignored in the conventional procedure is the value of management flexibility to revise operating policy with time according to the arrival of new information. Based on this oversimplification of reality, an optimum mine plan that is thought to be maximizing net present value (NPV) of the project is selected. Given the multiple sources of risk affecting the estimated NPV, there is a high probability that the actual value will be different from that estimated. This could mislead decision making process regarding selecting an optimum mine plan. This paper proposes a multi-criteria ranking system for selection between alternative mine designs under both geological and market uncertainties. The system is based on integrating multiple market and geological uncertainties as well as the operating flexibility to revise the ultimate pit limits using a Monte Carlo-based real options valuation (ROV) model. To compare the methods, the article applies the proposed system, along with the conventional NPV-based method, to rank possible mine designs for a copper and a gold mine. It has been found that, considering multiple risk analysis measures while integrating uncertainty and operating flexibility results in selecting a mine design that is different from that selected by the conventional method.

Jan 1, 2009

By D. Brunner, G. R. Baiden, H. J. Yazici

System simulation is an increasingly popular technique for analyzing and improving existing as well as newly designed underground mining operations. An engineering firm that specializes in simulation helped a major metals producer build a long-range planning model of an existing underground mine. Subsequently the team adapted this model to assess technology alternatives in the design of a new mine. The two models differ in the level of detail used for modeling the development process. This paper discusses the differences in approach between the models along with the experiences gained and challenges faced during the construction and use of the models.

Jan 1, 1999

By Y. Wang, K. S. E. Forssberg, A. Johansson, X. Lu

This paper presents the desulphurisation of a fine graphite powder below 80 µm by high gradient magnetic separation. The removal of pyrite (FeS2) and pyrrhotite (Fe1-xS) from the fine graphite powder was carried out with a modified version of the Sala dry HGMS with vibration assistance. In addition, a comparative study with dry and wet HGMS systems has also been performed. In order to establish the performance of the desulphurisation, a test series of varying parameters such as magnetic induction, matrix type/configuration and vibration were performed. As an equipment/process for removing sulphurous impurities from the fine graphite powder, the dry HGMS is deemed useful and comparative with the wet HGMS.

Jan 1, 2002

By H. Lyn Bourne

This is the seventh annual tabulation of royalty information. It is also the first year in which some data have been deleted to make room for new data. The concept of royalties evolved from a time when the government owned all of the land, including mines, to the situation where free miners won the right to claim minerals but paid a portion of their production to the royal treasury. Today, a mineral royalty is a payment to the owner of the mineral rights for the privilege of producing the mineral commodity. However, some people incorrectly believe that the selling price and the royalty are the same thing. The contract between the owner (lessor) and the mining company (lessee) is the mineral lease. Some clauses that are common to mineral leases include: identification of property, granting clause, reservations, definitions, royalty rate, taxes and title, indemnity, termination, inspection, assignability, successors, and reclamation. There often are variations in royalty rates for a given commodity that reflect differences in location, quality, market conditions or public versus private ownership. History In the time of ancient Rome, the government owned the mining properties by virtue of conquest. It would lease the mines to favored citizens who would pay rent to the State. Various conditions of sovereign ownership of both land and mineral rights continued in Europe until the Renaissance. As the laws evolved for land ownership by private citizens, the concept that minerals belonged to the State (King, Crown, sovereign) continued until about the 15th century. Free miners challenged the notion of sovereign ownership and won the right to discover and claim minerals. But a portion of their production had to be paid to the sovereign - a royalty. So, the original concept of a mineral royalty was a tax on production that was due to the Crown or Church. The term mineral royalty, as it is known today, is a payment to the owner of the mineral rights (formerly the royal owner) for the privilege of mining and producing the mineral commodity. The owner of the mineral rights, the lessor, and the mine operator, the lessee, enter into an agreement to mine the property. The agreement is the lease. While this concept is common, there are some who do not understand that the royalty is a portion of production paid to the owner as agreed on in the lease document. This author has seen reports where the selling price of a commodity has been quoted as the royalty. ("They get 70 cents a ton royalty at their pit and the guy down the road only has a 65 cent royalty.") These reports have been authored by people not familiar with the mining industry. Lease clauses In addition to the amount to be paid the lessor, there are several other items to be addressed in the lease agreement. The following list may not be all inclusive, but briefly describes most of the common clauses any good mining lease should contain. Identification: This opening clause names the owner (lessor) and the operator (lessee), the address of each, and gives the legal description of the property. Granting clause: This part of the lease gives the time period or duration of the agreement and information about renewal periods. It also has language about the exclusive right of the lessee to mine the property. Reservations: If the owner wants to exclude any portion of the property or set some specific conditions about the operation, there needs to be a clause that describes these reservations. Definitions: This section should address some of the technical terms that the lessor may find confusing - short tons versus cubic yards, dollars versus percentage of average selling price, any escalator indices such as consumer price index or producer price index, and material mined versus material sold. Royalty: This section spells out what the royalty rate will be, how often it will be paid, if there is an annual minimum, the pay dates, and how the records will be kept. This section also describes the conditions under which the lessee is exempt from the annual minimum - natural disasters, strikes, governmental actions, or other causes referred to as force majeure. Taxes and title: The lease needs to identify who is responsible for the property taxes, severance taxes (if applicable), and other taxes that relate to the mining activity - taxes on equipment, improvements, or stockpiles. This is a good place in the lease for the owner to certify his ownership of the property and its mineral rights and also certify that no other leases are in effect. The lessees may want language that allows them to pay mortgages or other debts on the property to keep their lease in effect. Indemnity: This portion of the lease identifies that the lessee assumes the risks for lessee's mining operation. Lessor should expect indemnification by the lessee through standard insur¬ance policies - workers compensation, liability and property damage. Termination: Both the lessor and lessee want language that will allow them to terminate the lease. This section of the lease describes the conditions under which one of the parties may terminate the lease (failure of the

Jan 1, 1989

By D. J. Kunz

Myanmar Ivanhoe Copper Company Ltd. (MICCL) has been operating the Sabetaung- Kyisintaung (S&K) Project producing LME Grade A Copper Cathode using the Heap Leach-SX-EW Process since 1998. The mineralization is mainly Chalcocite and the mine has a life of 20 years at the designed annual production of 25,000 tonnes of cathode copper. Design capacity was achieved within two of months of start-up. The mine is among the world’s lowest cost, Heap Leach-SX-EW operations. Information regarding plant design and operation are presented along with the challenges lying ahead and the latest developments. Daniel Kunz is President and Chief Operating Officer of Ivanhoe Mines, and a director of MICCL. He has more than 20 years’ experience in mining, construction and engineering. Prior to joining Ivanhoe Mines in 1996, Mr. Kunz was Vice President and Controller of Morrison Knudsen Corporation, a major international mining and construction company. He was also President and Chief Executive Officer of MK Gold Company, a public mining company listed on NASDAQ.

Jan 1, 2001

By James H. Dye, N. E. Norman

There will be about 300 raise boring machines used worldwide by late 1981, attesting to the acceptance of this drilling system by the mining and construction industries. Over the past few years, many articles have cited the advantages of raise boring: •improved safety; •faster completion of the raise; •elimination of sublevels; •cost reductions; •better structural characteristics of the opening; •labor reduction; and •noise abatement. The relative importance of each advantage varies from mine to mine. When analyzing the total economics of raising, each advantage must be considered. The factors having the most effect on economics are fixed costs, direct costs, and comparative savings versus conventional methods.

Jan 3, 1981

Due to deposit shape and dimension, narrow vein makes reserve modeling, geological control, stope design, drill and blasting more challenging. It needs high standard quality control as errors can be created easily, which could cause significant amount of ore loss or dilution. From channel sampling, survey control, reserve modeling, drill hole design, blasting, communication with underground drillers to backfill, this paper illustrated every step and its quality control of a long hole stope mining. Compared to other narrow vein mining methods (cut and fill and shrinkage), long hole stoping means higher production, less labor, and significantly lower cost when deposit characteristics allowed.

Jan 1, 2012

By O. F. Brown

The use of quality materials (aggregates and asphalt binder) in optimal proportions is the key to producing optimally performing hot mix asphalt (HMA). The Superpave mix design standard in the US introduced specific volumetric and binder property requirements in HMA design. Different methods for HMA constituent proportioning have been proposed in various guidelines. The design process to determine the HMA blend is currently iterative and engineers rely almost exclusively on experience. This approach is time consuming and often does not result in cost-optimal HMA mixtures. This paper introduces a mixed integer linear programming (MILP) optimization model for hot-mix asphalt constituent proportioning. The MILP model minimizes the total mix cost while satisfying all the volumetric, binder and mix property specification requirements. The model has been successfully validated with real-life example. The aggregates and binder ratios from the model were in close agreement with those from the contractor. The Bailey ratios and the gradation constraints were also satisfied. The cost of the optimal mix was $0.804/Mg less than that of the contractors?. This marginal reduction might make all the difference in an industry that is highly competitive. The MILP model also demonstrated that adding RAP to the contractor?s design would reduce the cost of the blend by $5.74/Mg. The virgin binder content was reduced by 1% because of the recycled asphalt contained in the RAP. This work represents the first successful attempt in incorporating both aggregate and asphalt performance requirements into the optimization formulation. Applying these models will ensure the minimum cost mix that meets all constraints and will increase profit margins for plant operators.

Jan 1, 2012

By J. R. Kunkel, V. Lishnevsky

At mine sites, the operational and required storage volumes of solution and water storage ponds and reservoirs are usually calculated based upon a water-balance approach. Many climatological variables including precipitation, air temperature, solar radiation, pan evaporation and relative humidity along with operating parameters, are used in the water-balance model. The water-balance model often seeks to find a “critical period” of wet or dry climatological sequences which result in a “maximum” pond storage volume or water demand. The problem with this approach is that the designer usually does not know when the project will come on line in relation to the historical record. To avoid this pitfall, we use a more robust approach. In the more robust method, the water-balance calculations begin in each year of the historic climatological record. This method results in the same number of water-balance runs (or realizations) as the number of years of climatological record. Results of this type of analysis guarantee that the critical period or maximum required pond volume will be found if it is assumed that the historical climatological record repeats itself or if a synthetic time series is used. In addition, this method permits calculation of the likelihood (probability) that a given pond volume will be equaled or exceeded in any given month of the operational life of the facility. In this paper, the results of the sizing of a heap leach pad solution pond are presented along with the probabilities of a given solution pond size being equaled or exceeded based on the robust water-balance approach.

Jan 1, 2002