Search Documents

By Poltak Sinaga

PT Kaltim Prima Coal?s 13-km (8-mile) overland conveyor (OLC) was commissioned in 1991. It is a conventional three-roller, 35 degree trough belt type. Cost and performance optimization during initial design resulted in a 5.4-m/sec (17.7-ft/sec) belt speed, 1,000 mm- (40 in.-) belt width to convey 1.35 kt/h (1,490 stph) and 7 Mt/a (7.7 million stpy) of coal. Despite a high initial figure, the belt speed was lifted to 6.5 m/sec (21 ft/sec) in 1996 to accommodate mine throughput in-crease. In 2002, a new low loss ST2100 1,100 mm- (43 in.-) wide belt replaced the ST2250 that was due to be changed-out. An upgrade project was initiated at the end of 2003 to further increase the belt speed to increase the OLC capacity to 30 Mt/a (33 million stpy). Upgrading the OLC by increasing the belt speed was the lowest capital option. Increasing belt width and/or modifying the trough angle to have larger cross sectional area was not an economical option because it would require expensive changes and significant down time of the OLC. To achieve 30 Mt/a (33 million stpy), the belt speed had to be increased to 8.5 m/sec (28 ft/sec). Although such high belt speed looked feasible, there was no information at that time of other OLC operating at such high speed. There was a risk that the conveyor would not operate safely and reliably at higher speeds. This risk was escalated by the fact there was no facility to lower or fine-tune the belt speed once the higher belt speed was implemented.

Jan 1, 2009

By J. Gentry

Chemical grouting has been successfully used for over forty years to control the movement of groundwater in a wide variety of applications including tunnels, subway systems, sanitary sewers, mines and construction projects. This paper illustrates the versatility of chemical grouts by reviewing three projects where chemical grout was utilized to address some very difficult water control challenges. The featured product is acrylamide which can be used alone or in conjunction with other types of grout such as cementitious products. Acrylamide grout is injected as a two component product that will react and form an impermeable gel when the components combine. There are notable differences between the acrylamide based products and cementitious products. The most notable and significant difference is that acrylamide is a true solution grout that contains no particulates and has a viscosity of 1-2cps. This feature enables the acrylamide grout to penetrate very small geological features that other grouts could not penetrate and to seal small cracks and fissures where groundwater seepage is occurring. The product also has an adjustable gel set time from a few seconds to several hours which enables the operator to determine the product travel before it forms a gel. When properly applied the product has a half-life in the soil of 362 years (per testing by the US Department of Energy).

Feb 27, 2013

By G. T. Lineberry, L. Adler

Due to safety-imposed constraints on clearances for mobile bulk handling equipment, it is necessary to optimally select a unit based on speed and size. The unit cannot be both large and fast. Since output is proportional to both size (or capacity) and speed, the combination must be carefully examined to maximize output. A simple graphical procedure and a calculus-based solution are presented to accomplish this. While the procedure applies to all mobile bulk handlers, as an example of the solution technique, attention is focused on shuttle cars. Background Major variables To fully define a bulk handling problem, the conditions, equipment, and activities must be characterized. The conditions and activities, when lumped together, are termed "encumbered space," since they "act to impede motion, as with a burden" (Lineberry, 1979). The insertion of mobile bulk handling equipment into what is already a difficult set of conditions and activities compounds the state of encumbrance, as limited space is competed for by many normal and life support systems. Long (1972) recognized the effects of design criteria, including road width, on haulage vehicle speed and, therefore, on production. Velocity -clearance curves Velocity-clearance curves are either available or can be constructed in the field. A preliminary set of curves for average conditions and activities is shown in Fig. 1, where clearances are only for the side of the vehicle (Lineberry and Adler, 1984). These curves set the safe speed limits for a vehicle operating at given clearances, under given conditions and activities. When feasible, velocity-clearance curves should be constructed through field measurement and observation. Curve construction should also consider haulway roughness, distances, and operator skill, as well as loading and dumping characteristics. It should be noted that haulage capacity determination is a total systems problem, not one just dependent on velocity and clearances. Production requirements and company capabilities also influence capacity determination.

Jan 10, 1985

By W. J. Kennedy, John D. Gardner

Introduction During the past 10 years, energy costs in mining have risen from about 4% to as much as 25% of total production cost. When combined with declining ore grades, these costs exert inordinate stress on mine productivity. Industrial engineering techniques have traditionally been aimed at improving manufacturing facilities productivity, but they have been applied to mining as pressure for productivity improvement has increased. These techniques can perform four useful functions for mining operations by improving methods, equipment selection procedures, energy use through scheduling, and managing energy costs rather than being managed by them. This article discusses some of the standard techniques for productivity improvement, and how they can be adapted to perform these four functions. Pre-Production The best time to seek high productivity is when a mine is being planned. During pre-production, when most options are still open, an optimum mine design is achievable. At this time, major equipment selections are made, the layout, material handling systems, and processes are designed, and critical energy source decisions are made. By including explicit energy cost projections, decisions can be made that will save significant amounts of money per ton of ore over the life of the mine. Attention can also be given to often overlooked details such as lighting. Some of the same tools used in new mine planning are applicable to productivity improvements at an existing plant. These tools are the charting and modeling methods that have been developed by industrial engineers over the past 75 years. Energy Consumption Before any analysis of energy consumption can be performed, preliminary work is necessary to find the kind of energy used, how much it costs the plant, and when electrical peaks occur. Past bills should be examined to determine the monthly consumption rate and the cost of each energy type. These data should be adjusted to remove effects caused by production fluctuations or weather. Knowing when electrical peak demands occur is necessary because these determine either the electrical capacity needed or the amount that must be bought. At $500-$800 per kW for construction or $5-$15 per kW per month for purchase, they represent a significant cost. By the time these data are collected, planners should be aware of the importance of energy in the total cost of mine operation, and should have the most crucial time data for electrical peak demand. Flow Process Chart Reducing costs can be accomplished by a thorough look at mine systems and how altering one system causes changes in others. By developing and exercising models of production processes outward to the transportation of the final product, otherwise obscured weaknesses may become apparent. There are tools available for analyzing the mine and its associated systems; one of the most useful is the flow process chart. The flow process chart gives a system analysis of a production procedure by classifying all actions into one of five types: operations, inspections, transportation, delays without paperwork, and delays with paperwork. Operation: In an operation, the nature of something is changed. Examples are blasting, washing coal, and processing matter. Denoted by 0. Inspection: Examining an object for identification or to measure some attribute. Examples are determining whether a drill hole is deep enough, deciding how far to cut under an unsupported roof when operating a continuous miner, or checking the lubricant level on a truck. Denoted bye. Transportation: Moving an object from one place to another. Examples are transporting overburden, moving coal on a conveyor belt, and pumping water. Denoted by =>. Delay without paperwork: A delay that is an inherent part of the system. Examples include idle time of a continuous miner while waiting for shuttle cars or for roof bolting, crushed ore in a storage area waiting for grinding and flotation, and people from one craft waiting for another craft to finish. Denoted by D. Delay with paperwork: A delay that can be terminated only by some written authorization. Examples are coal that cannot be removed until authorized by a bill of sale and transportation orders, personnel records, maintenance, or spare parts. Denoted by V. In practice, the flow process chart is completed after data collection and a detailed examination of the process. Data collection is needed to answer questions on distance, quantity, and time for each of the operations. As the analysis is being performed, each step of the process is subjected to these questions: • Why is the step necessary? • What is being moved? • When does the step take place, and why?

Jan 11, 1983

By Y. P. Chugh

During late 2010, a scientifically founded water spray system was developed for continuous miners (CM) (Patent Pending) that reduces respirable dust exposure for miner operator by about 30%. It includes engineered sprays around the cutting drum, outer bit-ring sprays, chassis sprays and side cutter boom sprays. About 3.6 ? 4.5m (12-15 ft) behind these sprays is additional sprays that spatially cover the area between the CM chassis and the mine roof and ribs. The spray system uses approximately the same volume of water as currently used on CMs with similar operating pressures. An Illinois mine decided to implement these concepts on a CM during rebuild stage. Dust control performance of the rebuilt CM was evaluated using gravimetric sampling and real-time monitoring using multiple personal dust monitors (PDMs). The average results based on about 105 cuts show about 30% and 20% reduction in dust exposure for the miner operator, and the haulage unit operator. Visibility in the mining areas was also significantly improved. The coal company has already decided to implement the system on all their CMs.

Jan 1, 2012

By C. M. Liu

"The Freeport-McMoRan Sierrita Crystal Plant produces Copper (II) Sulfate Pentahydrate (CuSO4·5H2O) through a series of cooling crystallizers. In this process, high supersaturation and unwanted spontaneous nucleation promote fine crystals. Seeding through recycled crystal classification can manipulate the crystal size distribution (CSD) for larger crystals. Proper selection of the crystallizer for seeding can prevent spontaneous nucleation and promote final crystal size. This study shows when seeding temperature is closer to the crystallizer temperature, suspension densities in the crystallizers are promoted and overall CSD shifts to a larger size of crystals. INTRODUCTION Figure 1 shows an overview of the crystallization process. The in-plant feed flow, called Pregnant Mother Liquor (PML), enters the first crystallizer and is subsequently cooled through a series of four crystallizers. Specific temperatures are targeted for each crystallizer to ensure the crystallization process is operating within the metastable zone (MSZ). The discharged flow from crystallizer #5 then enters two cyclones. The overflow from the cyclones contains smaller crystals providing seed crystals for crystallizer #5. The underflow from the cyclones begins the drying process. The overflow from crystallizer #5 enters cyclone #3 for removal of fine crystals and seeding purposes. The underflow from cyclone #3 has the capability to provide seed crystals for crystallizer #1 or crystallizer #2. The overflow leaves the system as Spent Mother Liquor (SML). Undersize crystals dissolve into the PML and return back to crystallizer #1.THEORIES AND METALLURGICAL TESTS Seeding requires an understanding of the crystal size, solution temperature and amount of crystals that enter the crystallizers (1). For the seed crystal size, classified crystal seeds can prevent fine crystals returning back into the system which eventually leads to excessive agglomeration (2). Proper selection of the crystallizer can ensure seeding at an appropriate temperature. Seeding at a temperature much lower or higher than the saturation temperature promotes spontaneous nucleation. Typically, seeding between 4-5°F below the saturation temperature is acceptable (5). A general rule of thumb is to add the seed crystals at the temperature between the solubility curve and the metastable zone. An experiment conducted by Mettler-Toledo AutoChem, Inc. indicates seeding close to the solubility curve rather than the metastable zone promotes a lower supersaturation and nucleation rate but yields a higher growth rate and a greater number of larger crystals (1). The amount of seed crystals can not only change the suspension density but also narrows the width of the MSZ in the crystallizers. An experiment conducted by Jaroslav Nyvlt reports with the crystals absent, the maximum allowable undercooling is 6.3 degrees at a cooling rate, 5°C/hour. With the presence of crystals, it narrows the MSZ width to 2.2 degrees (4). Industrial crystallizers normally operate at suspension densities between 15% and 25% by mass. When suspension densities are lower than 15%, it increases the risk of primary nucleation and the probability of incrustations; on the other hand, if the suspension densities are greater than 25%, it can cause a greater attrition rate and increase the probability of deposits (6). Moreover, operating suspension densities between 15% and 25% are also sufficient to minimize supersaturation rate which promotes crystal growth over nucleation (2, 6)."

Jan 1, 2015

By M. E. Kravetz, E. B. Milosavljevic, L. R. Solujic

Gold ores containing high levels of cyanide-leachable copper minerals, such as covellite, chalcocite, bornite, malachite, azurite, and cuprite have traditionally been difficult to treat economically. A novel hydrometallurgical process for efficient treatment of cyanidation effluents obtained by leaching high copper gold ores (or concentrates) based on the use of Cherokee Chemical organo-sulfur reagents (OSR-A, OSR-B and OSR-C) is described. The process may be modified to selectively precipitate silver, or completely recover silver, copper and zinc, as well as regenerate significant amounts of cyanide. For example, data obtained demonstrate that 100 % of silver and zinc, and 98 % of copper were removed from the solution, while 80 % of cyanide was recovered. The treated barren solutions exhibit enhanced gold and silver leaching kinetics compared to the untreated controls.

Jan 1, 2004

By E. V. Manlapig

This review paper describes recent advances that have been made at the Julius Kruttschnitt Mineral Research Centre (JKMRC) in Brisbane in developing a framework for simulating the flotation process. The work has been carried out collaboratively with the Mineral Processing Research Unit of the University of Cape Town in South Africa (UCT), as part of the Australian Minerals Industries Research Association (AMIRA) P9 Project. The framework consists of four components, namely – the mathematical model of the flotation process, suitable measurement tools for characterising the flotation cell, a computer program for modelling and simulating the process and the plantas for testing and validating the flotation models. A brief description of the model is first presented, then a number of applications of the model are described. The paper shows how the model can be used to optimise the performance of flotation cells, and then two case studies on the modelling methodologies are described. Finally the current and future plans of the project are outlined.

Jan 1, 2001

By D. H. Y. Tang, S. S. Peng

Three-dimensional finite element modeling (3-D FEM) was performed to analyze the safety factors of stump pillars, 5.5 m x 5.5 m, under a cover of 63 m using the Modified Drucker-Prager Theory. The results showed that they were safe. This was substantiated by underground observations. But the safety factors predicted by three commonly used pillar design formulae showed otherwise. This paper discusses the modeling details and analyzes the difference between 3-D FEM method and traditional pillar design formulae.

Jan 1, 1987

After World War I the character of my mining life changed completely. Before then adventure had been almost continuous but after the war there was lots of staying in one place, almost routine, between adventures. This was fortunate, as the life of a mining engineer is a wandering one at best, and it makes being married and raising a family a dubious enterprise. It would have been quite out of the question with the life I led before I got married at the end of the war The new sort of life made the "beaconing of adventure" intermittent. There were often long stays at home between wanderings which was fortunate as it changed the continuity of these memories. I must briefly summarize accounts of the more or less routine periods and concentrate on the occasional exciting episodes between. After a long visit with friends in Berkeley, Dorothy and I left for Arizona and three days at the Grand Canyon that were nearly too much for both of us. One beautiful day we started a short walk down the Bright Angel Trail. It was such a lovely bracing day that we kept on walking and enjoying the views until, just after noon, we reached the Colorado River. We were the only ones in sight so to enjoy the sunshine to the full we both had a good swim in the swiftly flowing river. So far, everything was wonderful. But when we started to climb back up the trail, rising nearly 6000 ft in ten miles we soon found that we had counted too much on our youth and endurance. We had to rest every few hundred feet and it seemed as though we would never reach the top. It was eight o'clock in the evening when we finally staggered into our room and collapsed. On the way to the Canyon I had seen John Greenway and Dr. Ricketts in Santa Barbara and they had little idea what would happen to them or to me. Before resuming his position as general manager of Calumet and Arizona and New Cornelia, Greenway must recover from the effects of the gas he had suffered in the war. Dr. Ricketts

Jan 1, 1976

By Charles W. Daugherty, Robert Nyren

The replacement of Boston’s elevated Highway I-93 running north to south through the heart of the city with 8-lane tunneled roadways, coupled with the underground extension of Highway I-90 eastward to Logan Airport, has earned the Central Artery/Tunnel (CA/T) Project the position of the largest infrastructure project in the U.S. today. The gigantic interchange featuring numerous ramps where these two main branches of the Artery intersect required the construction of three huge jacked tunnel boxes that were pushed beneath eight active Amtrak and commuter rail tracks that had to remain undisturbed in spite of poor geology and a minimum of cover between the track beds and the tunnel crowns. Ground freezing was chosen as the method of stabilizing the soil over the tunnels, and it was extended in one area to stabilize the ground at the intersection between the tunnels and an abutting deep cut-and-cover excavation. Because many standard geotechnical instruments consist basically of open standpipes filled with water, it was a major challenge to keep them de-iced and in a condition to provide data on vertical and lateral ground movements. The efforts to do so are herein described.

Jan 1, 2003

By W. J. Nokleberg, B. A. Bouley, T. K. Bundtzen

Central Alaska contains a wide variety of pre-, syn-, and post -accretionary mineral deposits that are related to the growth and evolution of the north-west North American continental margin. Withinpre-accretionary terranes, the Devonian-Carboniferous, carbonate platform-hosted MVT zinc-lead deposits of the Kandik and Reef Ridge districts in central Alaska, and the Devonian-Mississippian volcanogenic massive sulfide (VMS) polymetallic deposits of the Bonnifield, and Delta mineral belts of eastern Interior Alaska have received the most exploration interest to date. Syn-accretionary rift related, mafic and ultramafic sill swarms and zoned plutons of the Kluane-Nikolai igneous belt are currently being explored for Ni-Cu-Co-PGE deposits. Syn-accretionary granitoid complexes in the PurcellMountains, Illinois Creek, and Sitylemenkat areas have been explored for uranium-REE-gold, and tin-silver mineralization respectivelyPost-accretionary granitoid intrusions and associated volcanic fields that range in age from mid-Cretaceous to early Tertiary contain significant gold-silver-polymetallic resources in the East Central Alaska, Hogatza, and Kuskokwim Mineral belts. Collectively the three main post-accretionary plutonic/volcanic belts of central Alaska are part of the Tintina Gold Province, where exploration since 1990has identified about 848 tonnes gold.

Jan 1, 2000

By Ray Brainard

Treated effluent from the Clean Water Coalition (CWC) member agencies is currently discharged at an annual average rate of 6,570 l/s into the Las Vegas Wash, and is increasing annually. As the effluent flow increases, the nutrient loading of the treated effluent will approach the maximum limits allowed under the current regulations. To manage this flow while maintaining water quality in Lake Mead, the CWC is implementing a 44-km-long conveyance system. This paper discusses the geological and geotechnical aspects of the 13.4-km-long tunneled section through the River Mountains and their effect on design. The tunnel alignment traverses a heterogeneous package of volcanic and sedimentary rocks exhibiting widely variable rock conditions.

Jan 1, 2008

By J. L. Yordan, J. Kortmeyer, I. Yildirim

Talc is used to remove stickies from pulp during paper recycling processes. It is well known that the interaction is controlled by the surface chemistry at the talc/water, sticky/water and talc/sticky interfaces. If the interfacial tensions are known, one can calculate the free energies of interaction and hence predict whether the stickies can be removed by talc. In the present work, the surface tensions of several different talc samples were determined using the acid/base theory. The information was then used to determine appropriate interfacial tensions, which in turn were used to determine the free energy of interaction between talc and stickies. It was found that the calculated free energies are much more negative than those between the stickies and other minerals such as calcium carbonate, bentonite clay and kaolin clays.

Jan 1, 2002

By Kent Phillips, Meredith Scaggs-Witte, Emily Sarver, Cigden Keles

"After nearly four decades of decline, the prevalence of coal workers’ pneumoconiosis (CWP, or black lung) in the United States has been on the rise since the mid-1990s (Laney et al., 2014; Laney et al., 2010; Suarthana et al., 2011; Pollock et al., 2010; Antao et al., 2005; Blackley et al., 2016). Particularly alarming is the number of cases of rapidly progressive disease such as progressive massive fibrosis (PMF) (Pollock et al., 2010; Antao et al., 2005; Blackley et al., 2016; Laney et al., 2017). A recent study by Laney et al. (2017) observed 192 U.S. coal miners participating in the Coal Workers’ Health Surveillance Program (CWHSP) who had been diagnosed with PMF since 2000. Of the 163 (85 percent) that had a normal radiograph on file to use as a baseline, 27 (17 percent) of these individuals had progressed from a normal radiograph to PMF diagnosis in less than 10 years. Moreover, 162 (84 percent) of the individuals in that study worked in Kentucky, West Virginia or Virginia, and 169 (88 percent) had only ever mined underground. Blackley et al. (2016) also reported on a group of 60 PMF cases that were discovered by a single black lung clinic in eastern Kentucky. Since seeking care at such clinics and participation in the CWHSP are voluntary, and could be influenced by a number of factors, there has been some concern that these reports may overestimate the degree of resurgence in severe disease (i.e., versus disease that was previously under-reported). Even so, they highlight a critical need to better understand the cause(s) of disease development and progression — such that effective interventions can be devised.The notable uptick in CWP and PMF rates among miners in central Appalachia has led to this region being called a hot spot for disease (Pollock et al., 2010; Antao et al., 2005; Blackley et al., 2014; Laney et al., 2017). While the geographic clustering has been well documented (Pollock et al., 2010; Antao et al., 2005; Wade et al., 2011; Wang et al., 2013), the root cause is still unknown. Leading hypotheses have focused on the relative amount of rock being cut along with coal in many central Appalachian mines, as there has been a tendency to mine increasingly thinner coal seams over the past couple of decades (Laney et al., 2010; Schatzel, 2009). This shift has likely been accompanied by changes in specific dust exposure factors, such as increased abundance of particularly harmful dust constituents (e.g., silica or silicates) or increased frequency of harmful exposures (e.g., due to work in more risky environments) (Pollock et al., 2010; Blackley et al., 2016; Cohen et al., 2016; Douglas et al., 1986)."

Jan 5, 2018

By R. Oler

The mining industry?s traditional preference for protective coatings in corrosive environments, due to cost considerations, has been to apply galvanized and epoxy coatings. As a result of extreme pH levels and the limitations of current products, a new coating has been developed to withstand severe conditions. Harsh chemicals and corrosive groundwater pose added challenges to mines in maintaining long term ground support which demands continuous rehabilitation. This paper highlights the challenges and identifies a solution by applying a new economic coating to DSI?s Omega Bolt? that withstands the most corrosive of conditions. [ ]

Jan 1, 2012

By Jr. Smith

Borates have been mined in the desert areas of California and Nevada for more than 100 years. To about 1890, playa surface mining provided the chief sources of boron minerals. Underground mining of colemanite and later of borax and kernite was predominate until about twenty years ago. Open pit mining of the large deposits of borax and kernite near Boron, California has been most significant for the past twenty years. Mining of colemanite in the Ryan, California area, near Death Valley, began in 1907. Following the discovery of the large deposits in the Boron area (about 1957), mining in the Death Valley area became nearly nonexistent. Only small tonnages were mined for special uses. Little mining was done in the Boraxo area near Ryan. The first claim was made in about 1915 In 1960 the area became the property of the Kern County Land Company, which was acquired by Tenneco Oil Company in 1967. In 1976 the various borate properties and claims in this region were acquired by American Borate Corporation. The open pit mine is now approximately 400 feet (121.9 m) deep, 3000 feet (914.4 m) long and 1000 feet (304.8 m) wide. The borates in the Boraxo pit consist primarily of three minerals. These are about 50% coiemanite (C2B6O11' 5H2O), about 40% probertite (NaCaB5O9.5H2O), and 10% ulexite (NaCaBcO9.8H2O). The colemanite, along with boric acid and high-grade coiemanite ore from Turkey provide the only sodium-free borates for production of textile grade fiberglas. When heated to its decomposition temperature, colemanite decrepitates to a fine powder. This provides the basis for the concentration process. The gangue minerals in this deposit are primarily calcite and clays, including bentonite. The ore body has a very low arsenic content.which is a desirable feature. Test work had been done with samples prior to the results discussed herein. This paper will discuss results of test work which were the basis for erection of a plant, and the subsequent plant operations.

Jan 1, 1978

By Gary B. Hemphill

The 345 km long Taiwan High Speed Rail Project will connect the island’s two most populated cities, Taipei and Kaohsiung. Kaohsiung is the world’s third busiest port. The 23 km of alignment on Contract C230 requires the construction of 5,879 m of shallow mined tunnels ranging from 137 m to 1,285 m in length. All nine of these tunnels are mined using NATM methodology. Two of the tunnels, T01 and T08 are in the Toukoshan Formation. This paper will discuss the mining methods, ground support design, and the instrumentation installed to monitor and verify its effectiveness in the two aforementioned tunnels.

Jan 1, 2003

By W. L. Jacobsen, T. L. Dyer

Cortez Gold Mines completed a feasibility study for a new openpit gold mine in north central Nevada. The production schedule calls for a peak in material movement. This schedule is based on current operational efficiencies and equipment parameters observed at the company’s existing openpit operation. To mitigate risks of over/under predicting production, simulation modeling was used to validate the loading and haulage requirements during the peak production period. The advantage of simulation is the ability to provide a realistic model of a mining operation based on scheduled and unscheduled random events during the period under analysis.

Jan 1, 2007

Asgco’s design of the Arrowhead Ceramic Lagging provides solutions to problems experienced with conveyor belt slippage around the drive pulley and severe wear problems on snub and bend pulleys. Asgco has developed a range of pulley lagging from ceramic, drive rubber and non-drive rubber lagging that is available in abrasion-resistant SBR and MSHA grade rubber for conveyor pulleys from slow belts all the way through to high-speed, high load belts. There is a growing need for a maintenance-free and reliable pulley lagging to ensure conveyor belts run to their highest efficiency.

Jan 1, 2006